"current encoder settings for bit rate and sample rate are invalid" message

I have some files I am working with. Details and what happened:
Had some music files where I was doing some trimming/splitting. Files worked fine in itunes.
Open the files in Quicktime Pro 7 to trim them. Exported to aif.
Opened the files with itunes. They open and play just fine.
In Itunes I click"create AAC version" to convert them.
I receive the message "An error occurred while trying to import the file. The current encoder settings for bit rate and sample rate are not valid for this file."
I don't know what to do from here. Suggestions?
Thanks.

Make sure that the AIFFs that you export are set for 16 bit PCM.
Also, assuming that you are using 44.1 kHZ sampling in your AIFFs, make sure that you are not trying to use 48 kHz in the AAC.

Similar Messages

TS1717 when trying to import cd the following message appears "the current encoder settings for bit rate and sample rate are not valid for this file"?

Trying to import cd when this message appears "the current encoder settings for bit rate and sample rate are not valid for this file". Any suggestions?

Thanks so very much. I chose MP3 and Download and it is working beautifully. Have a wonderful day and it is so nice of you to get right back to me. I'm trying to cut a DVD for my grandson's grad party and I got most of the photos and didn't have any music since I lost everything in a clean install. Could hug you!

The selected combination of bit rate and sample rate is not allowed.

I've always burned my purchased CDs into iTunes using a AAC 320 kbps and 48.000kHz. Now when I select that option in iTunes 9 I'm getting a "The selected combination of bit rate and sample rate is not allowed." pop up screen. So is it impossible to burn my albums in a 320kbps/48.000 AAC format?. I had no problems in previous versions of iTunes using this setting. I guess I might have to switch over using a MP3 import setting instead.

Audio CDs are encoded with a sample rate of 44.1 kHz. Ripping them at 48 kHz requires resampling and does not improve the quality. Unless you have a special need for 48, use 44.1.

In Finder how do I get iTunes to show bit rate and sample rate of an entry?

In Finder how do I get iTunes to show bit rate and sample rate of an entry so I can set my DAC?

TonyEyes wrote:
In Finder how do I get iTunes to show bit rate and sample rate of an entry so I can set my DAC?
Tony, Make sure you are in Songs view. Then View > Show View Options, and check the boxes for "Bit Rate" and "Sample Rate." See picture:

Difference between scan rate and sampling rate? what is meant by throughput/maxt

want to know the difference and meaning of sample rate and scan rate ? what is meant by throughput and maximun throughput

Hello;
There is a really good KnowledgeBase at NI web site that talks about these definitions and differences.
The KnowledgeBase ID number is 2D6CTML8.
Hope this helps.
Filipe

Internal handling of Bit Depth and Sample Rate

I am wondering if iTunes allows accurate import of 48KHz/24bit files or whether it will convert to 44.1KHz/16bit as default. There is contradictory information in the Internet.
Thanks.

I just experimented on my machine, which is running iTunes 8.1. 48/24 WAV files can be added to iTunes. When adding to the library, it does not change them.
However, if you use iTunes as a conversion tool, it cannot create 48/24 files. The highest it can go is 48/16. That may be the source of the seemingly contradictory information that you read.
I did not try syncing the iPod. However, based on past problems with 48/16 files, I would not be surprised if the iPod has a problem with 48/24 files.

Hello All... Back after a brief absence, things look a little bit different. I'm trying to take a 16 minute mini dv video and compress it for use on the web. I'm interested in any suggestions you may have on settings for the video and audio tracks. I'v

Hello All...
Back after a brief absence, things look a little bit different.
I'm trying to take a 16 minute mini dv video and compress it for use on the web. I'm interested in any suggestions you may have on settings for the video and audio tracks. I've tried using Sorenson 3 (15 frames, key frames set to automatic, 320 x 240) for video and IMA 4:1 (mono) for audio. The resulting video looked great but the file size came in at about 255 Mb.
Thanks!
PowerMac G5 1.8 Dual Mac OS X (10.4.3)
Message was edited by: Dan Foley

Thank you for the replies. Everyone was correct about the jack, interface, and phasing problems. I have been unplugging my motu audio interface and then using headphones at work. I have not changed any detailed audio output settings in logic. When I read that the jack might be a problem I tried switching headphones. This actually helped. I am using dre-beats headphones and they seem to be having issues with the mac/jack-(the phasing/panning problems. I can use these headphones with other devices but not the mac. I have to use ipod ear buds and the phasing seems fixed. Hopefully this information is helpful to someone else.
If anyone knows how to correct this issue please let me know its difficult to know what my final mixes are going to sound like and I have had to keep bouncing everything into i-tunes- sync to ipod and then listen in my car radio.

How do I determine correct media encoder settings for Blu-Ray

I am successfully producing Hi Def Blu-Ray disks by using one of the presets available in Premiere media encoder. Actually using the HDTV 1080i 25 High Quality setting. They playback in beautiful high definition but I think I was just lucky. I would really like to know what determines the setting I should use.
1. I live in Australia so I assume PAL.
2. My camera is a Sony HDV. HCR HC9 1440 x 1080i. I assume this is irrelevant to export encoding settings for Blu-Ray.
3. The export encoder preset has field order set to Upper. I would have thought I should either match the project settings which is interlaced to match my camera and project. OR more likely I should match the audience TV which would be a widesceen plama or LCD TV. I dont know if these TVs are interlaced or progressive. OR is it more a question of what field order the Blu-Ray player expects me to send on the disk?
4. I will play on a TV 1920 x 1080 pixel capable and on slightly lower resoultion widescreens. The encoder preset is for 1920 x 1080 so I assume that's ok for all widescreen TVs even lower definition ones.
As you can tell I am a learner. Any suggested links to basic reading on the subject would help me.
Robert
PS Put this item in wrong forum previously.

Since no response I've been searching and found the following.
When encoding to make a Blu-Ray disk from my HDV 1080i footage:
1. Tell encoder the source is 1080i That is interlaced and it's TOP field first for HDV footage.
2. Tell it to encode to 1440 x 1080 resolution. You could tell it 1920 x 1080 but it will take much longer to encode. Will be good but why bother. All BD players will automatically up the 1440 to 1902 full screen.
3. Beware, not all players support BD-R and BD-RE recordable disks.
Seems Panasonic is good. Samsung probably good. Sony and Sharp probably not able to read (yet).
4. All players read MPEG-2 compression and H264 compression. Use a bit rate of 25 Mbps for MPEG-2 encode or 18 Mbps for equivalent result in H264 encode. Can use higher rates. These are minimums for a very good result
5. One pass encode is pretty damn good but use two pass if you have the time to wait for the encode.

Supported bit depth and sampling frequency

Hi,
Is it possible to determine at runtime what sampling frequencies and bit depths are available for audio capture -- other than by trial and error? It does not seem that way from the API, but maybe I missed something, so I decided to post a question here. The only thing I was able to find so far is that 8-bit PCM WAV is required to be supported by all devices that support audio at all.
Thanks in advance for any info!
Sergei

Thanks for the info. I guess I was looking for something more specific - the exact bitrates and sample rates that Creative claims to support. Would you know where official and comprehensi've data can be had? There must be a tech spec somewhere.
It is common these days in business to see a recording of, say, a conference call or seminar presentation at 32k bitrate/025Hz, or even 24k bitrate/8000Hz, posted to a company's website for download by those who could not be there, and MP3 players are increasingly used for their replay. Companies use low digitization rates because there is no need for hifi and the files are much smaller: less storage, faster download.
I'd be surprized to think that Creative don't have compatibility with the standard range of rates offered by ubiquitous programs like Audacity and dBpower, the latter being one they themselves recommend!

Strange info in "Bypass Proxy Settings for These Hosts and Domains"

For my Mac Mini my Network IP Address always has a self-assigned 169.254 number that I cannot change. Strangely, this same IP number is similar to info that is in the Proxies section (of Network Settings) under "Bypass Proxy Settings for These Hosts and Domains".
No matter what I do, this info (*,local, 169.254/16) appears in my Network Settings in the Proxies section under "Bypass Proxy Settings for These Hosts and Domains". (I tried removing the info and it would cause the "Configure Proxies" selection to default to "Always Use PAC File". Had to go back and retrash all the plist files to have Proxies go back to "Configure Proxies-Manually". Still, the info (*,local, 169.254/16) continues to appear in the "Bypass Proxy Settings for These Hosts and Domains" section and my IP address is always a 169.254 number.)
Comcast cable modem via direct hardwired Ethernet works fine with my other computer, so not the modem. Also, other computer does not have any info in the "Bypass Proxy Settings for These Hosts and Domains" section.
Installed a fresh copy of OS X 11.5 on a new hard drive. Still the same problem.
I posted this issue before but only got one responder and the problem still exists. Any clues? Somebody must know about this stuff. Help please.
Thanks

When your Mac wakes up, it does not yet have an IP Addresss. It wants to send a request to a Router for an apprpriste IP address to use now. But it needs to have an IP address (like a return address) to receive any messages. So, ... wait for it,
... it (your Mac) makes one up. There are rules that ensure it is a random address, but they always start with 169.254. It is on the same subnet with any low-order 16 bits This is the "self-assigned" range of IP Addresses. This address is only good for talking on a local network segment, for things like asking for a valid IP Address from a DHCP-enabled Router.
In most cases, on most networks, the 169.254 self-assigned IP Address is replaced by a valid Local IP Address such as 192.168.xxx yyy or 10.0.xxx.yyy so quickly that you never even see the 169.254 Address.
If you do see the 169.254 Address, it can be read as "Nobody will talk to me" or "Nobody will give me an IP Address". When you have this IP Address for more than an instant, you should suspect bad cables for Ethernet connections, bad signal strength or interference for wireless, Router configuration problems, or Mac configuration problems.
Mac configuration problems are often solved by using the "Assist Me" button is System Preferences > Network and choosing to set up again.
Another diagnostic is to try using Network Utility and the Ping function, and Ping-ing the address of your Airport base Station, often 192.168.0.1 or 10.0.0.1 or similar. This will tell you if the Router is reachable, or there are cabling/wirelss signal problems.
In this case, proxies are not an issue, and are simply a distraction from the real problems.

What are best Mpeg encoder settings for making DVDs?

In switching from PP1.5 to CS3 the procedure is different for making DVDs and we have to encode mpeg files that later get picked up by Encore DVD build proces. What are the best mpeg encode settings for making the DVDs?
Thanks,
Chuck Taylor

Question:
If you are doing a video that is small enough that you are not worried about size, what is the absolute best quality encoder settings? Would a Continous Bitrate result in a higher quality file generally? VBR is for trying to make a smaller file I assume.
I'm frustrated with even white letters on black titles that have some flicker. I just don't seem to get the smooth quality I desire.
Should I look at a different encoder?
If you output PP3 to an AVI and then import it into encore, isn't there a reduction of Q. due to the save to the AVI file?
thanks.

Conflict between the saved data and the sampling rate and samples to read using PXI 6070e

Hello, I am using PXI 6070e to read an analog voltage. I was sampling at 6.6 MHz and the samples to read were 10. So, that means it should sample 10 points every 1.5 um. The x-axis of the graph on the control panel was showing ns and us scale, which I think because of the fast sampling and acquiring data. I use "write to measurement file" block to save the data. However, the data was saved every 0.4 second and as 35 points data at the beginning of each cycle (e.g. 35 points at 0.4 sec and 35 at 0.8 sec, and so on) and there was no data in between. Can anyone help me how there are 35 reading points every cycle? I could not find the relation between the sampling rate and samples to read, to 35 points every 0.4 second!
Another thing, do I need to add a filter after acquiring the data (after the DAQ assistant block)? Is there anti-aliasing filter is built in PXI 6070e?
Thanks for the help in advance,
Alaeddin

I'm not seeing anything that points to this issue. Your DAQ is set to continuous acquire. I'm not sure if this is really what you want because your DAQ buffer will keep overwriting. You probably just want to set to Read N Samples.
I'm not a fan of using the express VIs. And since you are writing to a TDMS file, I would use the Stream to TDMS option in DAQmx. If you use the LabVIEW Example Finder, search for "TDMS Log" for a list of some good examples.
There are only two ways to tell somebody thanks: Kudos and Marked Solutions
Unofficial Forum Rules and Guidelines

Burn voice mp3 play list to audio CD. convert bit rate or sample rate.

I have several audio files (voice), 30 in all, that I wish to play in a car CD player.
The car player cannot play mp3. Using iTunes I tried buring a play list of mp3 files to an Audio CD.
I get an alert from iTunes that I may require multiple CD's. Each mp3 file is around 90megs in size or about an hours worth of audio (voice).
The audio files are voice no music. But they are at 192 kbps bit rate and 44 khz sample rate.
Is there a way of converting them to squeeze more files onto a CD? Changing bit rate or sample rate?
Can itunes do that? Or is there a utility that can do that?
thanks

Now that memory serves me right. CDs have the MB size and the Minute size on them. example 700MB/80Minutes.
How we forget...
Thanks though

Samples and Sample Rate

Hi there!
If i have 16bit, 44.1kHz samples loaded in the EXS24 and my current project is set to have a sample rate of 48kHz, will there be any "upconversion" by Logic to automatically play the samples properly, or should i manually convert the samples (or can i write a script?)
Thanks in advance.

The ESX24 reads the original sample rate and spits things out at the rate of the project. No conversion needed on your end.

Edit encoding settings for menus with animated background?

Hi there,
I just spoke with german support and they mentioned, that there is no way I can edit the encoding settings of encore how to generate the needed parts for an animated menu.
In this case I have a PAL M2V progressive scan used as BG and after menu rendering encore has created a M2V for the menu with strange interlacing problems ...
There seem to be options in the "project settings" > "default transcode settings" dialog (translated form german), but they are grayed out. There seems to be one setting "lower field" and I can not change to "progressive" ...
Its hard for me to believe that there are really no ways of altering the encode settings for menus. Has someone an idea?

Because DVD is Interlaced and not Progressive, I would do the Export of that Motion Asset to Interlaced with matching Field Order. There is nothing to be gained by trying to force En to do things that are not allowed by the DVD-specs. It is an authoring app. and not an NLE, so it needs the best possible, DVD-spec. material to work with.
Good luck, and hope that helps,
Hunt

"current encoder settings for bit rate and sample rate are invalid" message

Similar Messages

Maybe you are looking for