Current Monitoring Options?

I'm running a DeckLink card to an HDLink SDI->DisplayPort and onto a DreamColor.
This doesn't work with SG.
I'm looking at what other options i have.
It seems that the simplest might be a Quadro 4000 display port into the DreamColor as a second video card. It should be 10bit and RGB so should work with the DreamEngine colour processing. Does that sound like a plan?
The downside is that my original route is all video, which means that motion is rendered at exact frame rates whereas i'm worried that a card into dreamcolour will mess with the frame redraws (i.e. not be *exactly 50Hz* but over or under slightly.
What is everyone else doing?
thanks!
Paul

I have 2 cards because of Resolve ironically. (Only one outputs video to screens though)
In Premiere I have GUI for PPro application on 1 and full screen monitoring on the 2nd.. plus a BM card (sdi) to a BC Monitor.
IN SG I have GUI for SG application on 1 and full screen monitoring on the 2nd.
Neither of these setups use the 2 cards like Resolve does. ie. 1 for Monitoring...the other for GPU processing.
IN SG I see no way to set up two graphic cards.
Only solution I see is to dump the BM cards (!!!) and use AJA cards..

Similar Messages

Best Practice for ASA Route Monitoring Options?

We have one pair Cisco ASA 5505 located in different location and there are two point to point links between those two locations, one for primary link (static route w/ low metric) and the other for backup (static route w/ high metric). The tracked options is enabled for monitoring the state of the primary route. the detail parameters regarding options as below,
Frequency: 30 seconds               Data Size: 28 bytes
Threshold: 3000 milliseconds     Tos: 0
Time out: 3000 milliseconds          Number of Packets: 8
------ show run------
sla monitor 1
type echo protocol ipIcmpEcho 10.200.200.2 interface Intersite_Traffic
num-packets 8
timeout 3000
threshold 3000
frequency 30
sla monitor schedule 1 life forever start-time now
------ show run------
I'm not sure if the setting is so sensitive that the secondary static route begins to work right away, even when some small link flappings occur.
What is the best practice to set those parameters up in the production environment. How can we specify the reasonanble monitoring options to fit our needs.
Thank you for any idea.

Hello,
Of course too sensitive might cause failover to happen when some packets get lost, but remember the whole purpose of this is to provide as less downtime to your network as possible,
Now if you tune these parameters what happen is that failover will be triggered on a different time basis.
This is taken from a cisco document ( If you tune the sla process as this states, 3 packets will be sent each 10 seconds, so 3 of them need to fail to SLA to happen) This CISCO configuration example looks good but there are network engineers that would rather to use a lower time-line than that.
sla monitor 123
type echo protocol ipIcmpEcho 10.0.0.1 interface outside
num-packets 3
frequency 10
Regards,
Remember to rate all of the helpful posts ( If you need assistance knowing how to rate a post just let me know )

External monitor options For Macbook Pro(2011)

Just curious as to what my monitor options are as a external monitor for the Macbook Pro. I'm pretty much set on 27'' thunderbolt display but its a hefty price to swallow...
Best buy has some good deals on there 27'' monitor but can i get the same resolution and clarity from other brands that will be eqivalent to Apple?
I'd like to stay in the 27'' to 30'' size...
thanks

Any other options like Samsung, LG etc... that offer the same specs as the thunderbolt display?
Thanks

Can anybody tell me where the export current frame option is in the new final cut update? It used to be under the share menu but that menu has now been removed.

Can anybody tell me where the export current frame option is in the new final cut update? It used to be under the share menu but that menu has been removed now.

When I click File> Share> There is no save current frame option. Also Cmd E isn't working either.

When will Apple offer a "print current page" option????

There are 2 things I like about Windoze:
1. I am tired of having to tab to the pages area of the print dialogue box and type 2 & 2 again, when I really wish Apple would just put a print current page option.
Can anyone who works @ apple see that it gets implemented next update?
2. And also make it so we can resize a window from any side? Windoze does it, why not apple?

Chris,
Sorry, but this is a user-to-user discussion forum. There is no one from Apple paid to read and respond to these posts. I have Never seen an Apple employee respond to the subject of a post here - only administrative stuff like You're not allowed to use that kind of language here, etc.....
Please go to the Tiger Mac OS X Feedback area - that is the place to give input to Apple.

PRO Tip Monitoring option was disabled on SCVMM

Hello,
I have integrated SCVMM 2012 R2 and SCOM 2012 R2 also test the PRO ,the jobs ran successfully.
But i could not able option to enable PRO "Monitor option"(it is disabled) on SCVMM.how to enable this.

You must be a member of the Administrator user role to set up and modify the connection to an Operations Manager server
Also check below links
http://blogs.technet.com/b/scvmm/archive/2011/04/14/operations-manager-integration-and-pro-improvements-in-scvmm-2012.aspx
http://blogs.technet.com/b/kevinholman/archive/2012/08/21/integrating-vmm-2012-and-opsmgr-2012.aspx
Please remember, if you see a post that helped you please click "Vote As Helpful" and if it answered your question, please click "Mark As Answer"
Mai Ali | My blog: Technical | Twitter:
Mai Ali

How to get the name of current monitor?

I have a script which is used to get some application data. The script take parameters such as "LOB" so it can query data for different department. When it found something, it raise an event in event log.
Therefore this script is used by several different monitors. Each monitor calls the script by passing different parameters. To better understand the event was created by which monitor, I want the script can get the name of monitor which calling it and they
list it in the event log too.
Currently, I am passing $MPElement$ as one script parameter so I can get the monitor's GUID. Then get the name by running powershell command. Is there an easier way to get the monitor name? Thanks!

The best way to do this is to put the monitor name as a property bag in the script and pass that to your event details. Otherwise, we're looking at querying the database each time the monitor generates an event, and this is overhead that is really not
necessary. The other option, which is just even worse in terms of performance, is to use powershell to query the SDK for the monitor name. Both of these options are not going to be a good solution, because now you need to implement action accounts that can
either query the database or the sdk.
Jonathan Almquist | SCOMskills, LLC (http://scomskills.com)

Output to monitor options

My late 2011 13" MBP only has one TB output which I currently use (TB to hdmi adaptor ) for my samsung hdmi monitor but would like to use the TB out to connect to a TB HD that also only has one TB port. What are my options if any?
Many thanks
Dave

Thanks for your help, I was just referring to
>> Since Thunderbolt displays should always be at the end of a Thunderbolt chain, I'm not surprised that the display you're looking at has only one TB port.<<
It's not a TB Display as I said & understand that if it was why it would only have one TB port, but this point is a little redundant/confusing as it's not relevant to "this" conversation.
I have however looked at TB hubs & the Caldigit TB hub seems like a good option especially at below $200. --> http://eshop.macsales.com/item/CalDigit/TSUS60/
There also seems to be a much cheaper option ($58) USB to hdmi/VGA option both at OWC . This of course ties up a USB port but I might try this first because of price--> http://eshop.macsales.com/item/Newer%20Technology/VIDU2DVIA/
Many thanks again
Dave

Thunderbolt to SDI Monitoring Options?

I've been reading here that the current SDI reference monitor setup I've used for Resolve will not work wtih Speedgrade since it uses the Blackmagic Mini Monitor to connect Thunderbolt to the SDI.
I'm interested in moving over to Speedgrade for grading if possible, but I'm using the new MacPro and iMacs -- none of which work with nVidia cards. At this point all Apple Mac solutions will need to be Thunderbolt based.
So what is the simplest and least expensive way to get an SDI signal from a thunderbolt port that is compatible with Speedgrade?
Thanks!

BMD makes 4 different types of TB output devices, Aja makes another 3.
You have to decide what works for you and your workflows since you have not mentioned what type of content you work, so it's impossible to offer suggestions. Option are available for HD and 4K output from both companies.
I work on commercials, features and episodic television, I use the best tools I can get my hands on,
Gary Adcock
Studio37 Inc.
Production and Post Workflow
Camera and OnSet Technology.
Chicago, IL. USA.
This device has a tendency towards horrible spelling, it's actually worse than my spelling naturally is.

Multi-Camera Monitor Option Missing

Hello, Please help.... I just downloaded the CS6 Premeire Pro and I don't have the Multi-camera monitor in my window tab... Can you tell me if I have to do to get that option?

Create a new Sequence and add your clips to their tracks.
Sync them up, then nest that into a second Sequence.
Right click that Nested Sequence and select Multi-Camera > Enable.
Then:
I just downloaded the CS6 Premeire Pro...
Be sure to update to the current version (CS6.0.5).
Within Premiere: Help > Updates...

'Setup System Monitoring' option is disabled in solution manager

Hello,
I am trying to setup system monitoring for different systems in solution manager but the 'Setup System Monitoring' is disabled.
In solman I go to Solution_manager --> Operations Setup --> on the right side pane 'Setup System Monitoring' is disabled. How can you change this to change mode so that you can configure monitoring for different systems? Any idea, please help.
Thank you in advance.
Sameer
Edited by: Sameer Pant on Mar 19, 2011 1:07 AM

Hi Lakshmi,
But when i right click on the qualifier
No u hv to right click on a field to which Compound field is mapped ( Ur Main Table Field)
Right Click on Compound field & choose option Set Qualified Update.
New Links: Create
Existing Links: Update (All Mapped Qualifiers)
Thanks,
Maheshwari

Late 2005 G5 Monitor Options

I ran twin 22" Cinema Displays since 1999, and one went south with the infamous two short, one long flashes. Tried switching/reconnecting, but no change-- it's the monitor.
I assume my original 6600LE video card won't run a 30 inch at high resolution, but are there any monitors in the 24 to 26 inch range that will run well with my current set-up? If not, with an upgraded video card?
With a larger monitor, I might retire the two monitor system. 90% of my work is writing, with 3 or 4 docs open and in view. I do some video editing, but I don't need perfect colors like a graphics designer.
Thanks for any tips.

Hi-
The 6600LE has one dual link DVI and one single link DVI.
You can run a 30" monitor at optimal resolution of 2560 by 1600 connected to the dual link DVI.
So, get the monitor that you want.

Apple monitor options for pismo?

hi all,
i'm thinking of getting an external monitor for my pismo - to give the lcd a rest and as an extended display for fcp etc. i was thinking of a 17" crt apple studio display - the clear backed ones - as it wouldn't bee too expensive and they look cool as well. however i've been told that these monitor don't have an agp connection and a converter is big $$. i could get a new (non-apple) lcd, or second hand non-apple 17" quite cheaply, but with google having proved fruitless i'm just wondering what apple options there might be?
cheers!
sennen.
G4 550 pismo Mac OS X (10.3.9)

ah, thanks for that jpl! i have that adapter! tho i'm wondering if that document refers to the clear or graphite crt displays or both? i was told by a re-seller that the clear backed crt a) doesn't have the right connection, and b) as the power and monitor connection is all in the same cable that it won't run off a powerbook... could be bad info...
thanks!
sennen.
G4 550 pismo Mac OS X (10.4.7)

ASA SLA Monitoring Options

Hi,
Does the "Number of packets" option mean that all the packets specified must exceed the threshold, or is it only one that can be missed? The internet connection for the config below is not very reliable and ping responses are regularly dropped. I beleive this could be causing the route to change to the backup connection when not needed.
Thanks

Hello Dustin,
The "number of packets" configuration is the amount of ICMP request packets that are going to go out from the ASA to the target, and these packets are the ones that are going to be inspected or monitored so if they are getting regularly dropped the test is not going to pass and a Failover between the routes will happen.
Please rate helpful posts.
Have a good one
Julio!!!

BUSINESS PROCESS FLOW (BPF) TASK SETUP - CURRENT VIEW OPTIONS

This article explains a few findings regarding the options on Current View Type for setting up Business Process Flow tasks and will discuss BPC for Excel, Data Manager and BPC Web tasks.
Future posts will cover more tasks.
This is valid for 5.x versions only.
IMPORTANT NOTE:
DATA MANAGER PACKAGES
    Data Manager Packages tasks such as Run Specific Package, Run User Package are not integrated
    with the Current View Type selection. Therefore, the options Inherit from Data Region, Inherit from
    Current View or Member Lookup does not work on Data Manager Packages. This is due to the diversity of Data Manager Packages, such as Import, Export, Clear, Default Formulas, each of them requiring a complete different set of parameters, some of them not related to the Current View.
1. INHERIT FROM DATA REGION
Once you choose to Open a BPF from BPC for Excel, you are prompted to choose the Data
Region. Upon setting the desired Data Region, the Current View is changed
accordingly on BPC Web.
    OPEN TEMPLATE / REPORT LIBRARY / SCHEDULE LIBRARY
    If a step is defined as Open Template/Report Library/Schedule Library
    and INHERIT FROM DATA REGION is set to one (or more) of the Data Region
    dimensions, the Current View on BPC for Excel should change to match
    the settings done Data Region settings, being the same as the one on BPC Web.
    SET WORK STATUS
    Same as above.
2. INHERIT FROM CURRENT VIEW
    OPEN TEMPLATE / REPORT LIBRARY / SCHEDULE LIBRARY
    If a step is defined as Open Template/Report Library/Schedule Library and INHERIT FROM
    CURRENT VIEW is set to one (or more) dimensions, the report will pickup the Current View
    from BPC Web and BPC for Excel should change to match the Current View,
    being the same as the one on BPC Web.
    Example:
    1. Log on to BPC Admin on ApShell -> Manage Application Sets;
    2. Go to Business Process Flows -> Budgeting Process;
    3. Grant access to the BPF to your test user;
    4. Check Sub-Step 1 of Step 1 - Check Budget Data. This steps has a
       INHERIT FROM CURRENT VIEW setup (ENTITY).
    5. Log on to BPC Web on ApShell;
    6. Go to Open a Business Process Flow and choose Budgeting Process;
    7. Choose the desired Data Region;
    8. On BPC Web, verify the value setup for ENTITY on the Current View;
    9. Open the Check Budget Data;
    10. The ENTITY on the Current View will be set up accordingly to what
        was set on BPC Web.
    SET WORK STATUS
    Same as above.
3. MEMBER LOOKUP
    OPEN TEMPLATE / REPORT LIBRARY / SCHEDULE LIBRARY
    If a step is defined as Open Template/Report Library/Schedule Library and MEMBER LOOKUP
    is set to one (or more) dimensions, the report will set the Current View
    on BPC for Excel to the member that was configured.
    Example:
    1. Log on to BPC Admin on ApShell -> Manage Application Sets;
    2. Go to Business Process Flows -> Budgeting Process;
    3. Grant access to the BPF to your test user;
    4. Check Sub-Step 1 of Step 1 - Check Budget Data. This steps has a
       MEMBER LOOKUP setup (CATEGORY).
    5. Log on to BPC Web on ApShell;
    6. Go to Open a Business Process Flow and choose Budgeting Process;
    7. Choose the desired Data Region;
    8. On BPC Web, verify the value setup for CATEGORY on the Current View;
    9. Open the Check Budget Data;
    10. The CATEGORY on the Current View will be set up accordingly to what
        was set on the Task configuration, in other words, there should be BUDGET set
        on the Current View.
    SET WORK STATUS
    Same as above.
REFERENCES
This is an unofficial addendum for the SAP BPC 5.1 ADMINISTRATION USER'S GUIDE on:
PAGE 54 - Managing Business Process Flows
PAGE 57 - Adding new business process flows -> To add a step -> Select the current view type
SAP BPC 5.1 ADMINISTRATION USER'S GUIDE can be found on [BPC Instalation Guides and User Guides|http://service.sap.com/instguidescpm-bpc].
Edited by: Gustavo Bortoloti on Dec 15, 2008 6:48 PM

Hi Gustavo Bortoloti,
That's right, the SAP BPC version 5.x SP x not have the specific setting.
Thanks,
Wandi Sutandi

Current Monitoring Options?

Similar Messages

Maybe you are looking for