CVP supports mixed G.711 and G.729

"CVP supports mixed G.711 and G.729"
Where do you configure the allowed codec(s)?
Also, if the ingress gateway is also the vxml gateway and the ingress is SIP with g729 only (so no midcall renegotiation) but the vxml call leg is g711 -- how do you specify the transcoding resource to be used? If I change the vxml call leg to use g729 (flat codec) also, do I still have to go through the whole hex editing thing mentioned here (http://www.cisco.com/c/dam/en/us/td/docs/voice_ip_comm/cust_contact/contact_center/customer_voice_portal/cvp8_0/release/notes/cvp_801_rnotes.pdf)? I couldn't find any mention of this in the later CVP release notes, so not sure if it's still needed.
thanks,
will

Thanks for the quick reply Chris!
"You configure them on your dial-peers and region setting in CUCM."
CUCM isn't involved yet though unless I'm missing something (which isn't as rare as I'd like). CVP sets up the VXML call leg from the ingress gateway to the VXML gateway (same device here) right? Does it just use the same dial-peer level codec(s) as you are allowing in your cube->cvp call server dial-peer? Is that what you mean?
LTI looks pretty slick, but I can't find any info regarding compatibility with CVP although I'm not entirely sure how that codec selection (ingress gw to vxml gw) works. Codec renegotiation is out unfortunately. It's g729 ingress with every call transcoded at the CUBE to g711. Trying to retroactively fix this and other design flaws and we'll have to move the agents to g729.
Looks like we either transcode for the VXML call leg or migrate that to g729 as well. Seems like transcoding gives us the flexibility to add asr/tts at a later date if/when requirements change. On the other hand, using a flat codec end to end makes troubleshooting easier and frees up those dsp's. Any advice/experience to share one way or the other?
thanks,
will

Similar Messages

ADF Faces: is mixing JSF RI and ADF Faces tags supported?

Hi,
I'm looking at ADF Faces as a future possibility for our application that is currently based on JSF RI.
When looking at the ADF Faces demo it strikes me that all pages are almost completely built up from ADF Faces tags.
For instance
af:form
af:commandButton
af:inputText
are used instead of the equivalent core jsf tags f:form, f:commandButton and f:inputText
I'm wondering if this is mandatory if we would like to use some ADF Faces components mixed within our existing application.
In other words: are ADF Faces tags supported in the environment of conventional JSF tags? And mixing ADF Faces JSF components with JSF components by other vendors?
Another thing that strikes me is that pages are constructed using ADF Faces tags for any and all markup content.
I guess this is meant to support several different clients (normal browser applications, mobile clients, voice activation over telephone) using different renderers.
In my experience abstracting markup this way inherently means loss of control over the exact markup that is sent to the client. This is not acceptable for all projects and customers.
Is embedding ADF Faces tags within template HTML, within f:verbatim tags or not, supported?
Regards,
Joost de Vries

You absolutely can mix JSF RI and ADF Faces tags. This is very much supported! You can swap in <h:form> and <h:commandButton> and <h:inputText>. Our versions support some features that the JSF tags do not, as described in our release notes.
Your point about using tags to produce all markup is a very cogent one. For some projects, absolute control over HTML will be a necessary requirement, so we do support that style of development. But we believe strongly that the future does not lie in constant handcoding of HTML, but instead in building more powerful, flexible, and reusable components and assembling those into pages. This was one of the themes of a talk I gave with two coworkers at this past JavaOne.
-- Adam Winer (JSF EG member and ADF Faces lead)

Unity and G.729 Calls

Hi All,
I need to know if Cisco Unity supports G.729 calls or no?
what I know it does not.
I have a customer has a lot of branches and centralized CUCMs and Unity in HQ.
I placed the phones in HQ in HQ device pool. HQ region
and phones in BR1 in BR1 device pool. BR1 Region
Voice mail ports are in HQ device pool.
so if IP phone in HQ called Unity the call is G.711ulaw here no problem.
I was surprised when I plced call from IP phone in BR1 device pool to Unity and Unity accept the call and I checked the call by pressing ?? and it was G.729.
I checked the Media resources conifguration I do not have any transcoder defined in the Cluster.
any advise??

Yes, Unity Connection is the same. CUE supports only g.711. See the following link for the steps to disable g.729 in Unity Connection.
http://www.cisco.com/en/US/docs/voice_ip_comm/connection/7x/administration/guide/7xcucsag140.html
The advantage of forcing an external transcoder is increased performance. With a handful of calls being transcoded in software by Unity, there is no problem. If you ask Unity to transcode thousands of g.729 calls, you're going to see performance issues with the Unity server.
Hope this helps.
Brandon

Is there a way to "mix" the nodes and leaves of the tree so if they are at the same level, they will display in a specified order.

Is there a way to "mix" the nodes and leaves of the tree so that even if they are at the same level (1,2,3...), they will display in a specified order (via sort sequence, alphabetical, etc.).
History:
We are using the Tree UI element to display/manage a material bom interface. We seem to be running into an issue with displaying the nodes/leaves of the tree.. regardless of the order that the context is built (which is currently the order of the exploded BOM from from CS_BOM_EXPL_MAT_V2), the bom is displayed with the nested boms at the top of each level and the single materials below them. For example. If TK1 contains Material1, Material2, Material3, Kit1(containing component1, comp2, comp3), Material4, Kit2(containing comp4, comp5, comp6), and Material5 (in this order), the tree will display with the A level node as TK1, the next node as Kit1 (with its subleaves of comp1,comp2,comp3), Kit2(with subleaves of comp4,comp5,comp6), THEN Material1, material2, material3, material4, material5. Our users are adamant about the items displaying in the correct order (which should be alphabetical based on the description for one report and by location for purposes of inventory for another). I've searched but not been able to locate a similar question. If I've missed it, please point me in the right direction. The users want the tree, not a "tree" table. This is our first attempt at the tree, so maybe we're missing something basic?
TK1
-Mat1
-Mat2
-Mat3
-Kit1
--Comp1
--Comp2
--Comp3
-Mat4
-Kit2
--Comp4
--comp5
--comp6
-Material5
displays as
TK1
-Kit1
--Comp1
--Comp2
--Comp3
-Kit2
--Comp4
--Comp5
--Comp6
-Mat1
-Mat2
-Mat3
-Mat4
-Mat5

co-workers said example picture is misleading.. we can make the order work if everything is a "folder" but not a mix of "folders" and "files" (if making a visual reference to the windows browser). i.e - a file is represented as an empty folder.
TK1
. Mat1
. Mat2
. mat3
> kit1
.. comp1
.. comp2
.. comp3
. mat4
> kit2
.. comp4
.. comp5
.. comp6
. mat5
displays at
TK1
> kit1
.. comp1
.. comp2
.. comp3
> kit2
.. comp4
.. comp5
.. comp6
. mat1
. mat2
. mat3
. mat4
. mat5
we can make it work if everything is a folder. This is our current workaround.
TK1
> mat1
> mat2
> mat3
v kit1 (when expanded)
.. comp1
.. comp2
.. comp3
> mat4
> kit2 (when not expanded)
> mat5

Canon 860 Series (Pixma) Printer Problems with OSX 10.8 (Mountain Lion) – links to Canon Support Site with Drivers and Software with install tips

After spending several hours sorting out Canon Pixma OSX problems here are my thoughts:
Canon 860 Series (Pixma 868) Printer Problems with OSX 10.8 (Mountain Lion) – links to Canon Support Site with Drivers and Software with install tips
Problem:
- New imac and MacBook Pro 2012 (OSX 10.8.2) had a problem using Canon Pixma 868 printer on network and would not scan or print using Canon Pixma software (Pixma MP Navigator 2.1 & Photo Print), which has advanced scanning and photo printing functions.
- When I connected the canon printer to my imac, OSX 10.8.2 automatically downloaded and installed drivers for Canon 860 series printer. I could then add the new printer (select ‘apple menu’ / ‘system preferences’ / ‘print and scan’ / “+”) and printer would work while connected via USB but could not get to print or scan over network wifi.
- The original Canon 860 Series CD does not work with 10.8 and the manual / online instructions did not make sense (as based on CD install).
Solution:
1) Install Canon Printer Drivers and Software (from official Canon site)
Go to canon support site, review FAQ, then download and install following Pixma 860 Series software & drivers for OSX 10.8 (links see below). The version I downloaded is in brackets but check for updated version. Full instructions are below.
Canon 860 Series Drivers & Software for OSX 10.8 Mountain Lion:
The base software and drivers needed for using Canon 860 Series on Mac OS X 10.8 (USB) are
1 Printer Driver
(Canon MX860 series CUPS Printer Driver Ver. 10.67.1.0 (03-Aug-2012))
2 Scanner Driver
(Canon MX860 series Scanner Driver Ver. 14.11.4a (03-Aug-2012))
3 Network Tool
(Canon IJ Network Tool Ver. 4.1.0 for Intel Mac (27-Dec-2012)
Canon Software for using advanced printing and scanning functions (while connected to network)
4 Solution Menu
(Canon Solution Menu Ver. 1.4.1 (27-Jul-2012 ))
5 MP Navigator EX
(Canon MP Nav EX Ver. 2.1.3 (02-Auf-2012))
6 Easy-PhotoPrint EX
(Canon Easy-PhotoPrint EX Ver. 4.1.6 (21-Jan-2013 ))
Canon Support (HK) – check your local site
http://www.canon.com.hk/en/download/main/index.do
Select Product and drivers from support site eg http://support-hk.canon-asia.com/
1. Choose a product category
Multifunctional Printers
2. Choose a product series
Pixma
3. Choose a product model
Pixma MX868
4. Choose type of document
Downloads or FAQ
If you have problems installing the software under 10.8, see the FAQ on Canon site. You will need to allow software installs from “unidentified developers by using “Control” Key or by changing your system preferences)
2) Check Canon Printer and Software Working while connected via USB
Once you have downloaded and installed drivers and software and restarted computer, check that the printer and Canon Pixma software (Pixma MP Navigator 2.1 & Photo Print) are working via USB. Open the Canon IJ Network Tool App (Applications / Canon Utilities /IJ Network Tool / Canon IJ Network Tool App) and make sure you can see the Canon MX 860 series (xx.xx.xx.xx.xx.xx) and that it shows the correct SSID Wifi settings (under the Canon IJ Network Tool App ‘Setup menu’). This is normally done as part of the automatic install but worth double checking
3) Add new network printer using ‘apple menu’ / ‘system preferences’ / ‘print and scan’ / “+”).
After you have checked USB printing turn off printer, unplug the USB cable and shutdown the Canon IJ Network Tool App.
Then turn the printer back on and wait 30s. Then add a new printer using ‘apple menu’ / ‘system preferences’ / ‘print and scan’ / “+”). Once you select “+” (add new printer), wait 10-30s for the Wifi Networked Canon MX 860 Series printer to appear in the new window eg Canon MX 860 series (xx.xx.xx.xx.xx.xx) (Kind: “Canon IJ Network”)
DO NOT ADD THE MX 860 SERIES BONJOUR SCANNER (the Bonjour Scanner is the built-in software, is not needed and often appears first on the add printer list). The Canon scanner can be accessed used through the MP Nav EX Ver. 2.1.3 software (which has much better functions)
You will now have two Printer Canon MX860 (USB) and Canon MX860 (Wifi / Network). Set the Canon MX860 (Wifi / Network) as default and test print and scan
If the Wifi Networked Canon MX 860 Series printer does not appear, check the printer and make sure that the printer can see the wifi network. On the printer select Menu / Settings / Device Settings / Lan Settings / WLAN Setting List. It should say WLAN Active, identify the SSID and have an IP address
If the printer can not see the Wifi Network, plug the USB cable back in, then open the Canon IJ Network Tool App (Applications / Canon Utilities /IJ Network Tool / Canon IJ Network Tool App). Make sure you can see the Canon MX 860 series (xx.xx.xx.xx.xx.xx) and that it has your SSID settings (under setup), if it has this info, restart the computer and the printer and try again

Hi, thaks for response, meant to post as a discussion (not question), wanted to save others time if they get the same problem

3 iphones in household.All use same apple ID.But all contacts get mixed between phones and facetime calls come in from other contacts.Ho can we change this so our phone information isn't visible to each other?

3 iphones in household.All use same apple ID.But all contacts get mixed between phones and facetime calls come in from other contacts.How can we change this so our phone information isn't visible to each other?

Use separate Apple IDs for each family member and use Family Sharing features of those things (if any) that you do want to share. https://www.apple.com/ios/whats-new/family-sharing/

On my ipad mini, when I delete an email from the inbox (and it goes into Trash), it immediately deletes that email from the server (ATT/Yahoo). I've called support for both ATT and Apple and can't find a way to have the emails remain on the server.

On my iPad Mini, when I delete an email from the inbox (and it goes into Trash), it immediately deletes that email from the server (ATT/Yahoo). I've called support for both ATT and Apple and can't find a way to have the emails remain on the server.
My husband and I share an email address and if he misses a day checking email on his notebook, he doesn't receive the items that I have sent to Trash on my iPad Mini.
Appreciate suggestions.
[The curious thing is, if I "move" the deleted emails from Trash on my iPad Mini into the Inbox, I can go to my notebook, open my online email and they are back in my ATT/Yahoo Inbox.]

Is your Yahoo account set up as POP3 or IMAP?

When I try to launch itunes I get an error mesage saying that Apple application support was not found and suggests that I uninstall and re-install it, but that doesn't work

When I try to launch itunes I get an error mesage saying that Apple application support was not found and suggests that I uninstall and re-install it, but that doesn't work

For general advice see Troubleshooting issues with iTunes for Windows updates.
Start with the section Install missing components which should address your particular error. Otherwise the steps in the second box are a guide to removing everything related to iTunes and then rebuilding it which is often a good starting point unless the symptoms indicate a more specific approach. Review the other boxes and the list of support documents further down page in case one of them applies.
Your library should be unaffected by these steps but there is backup and recovery advice elsewhere in the user tip.
If you've already tried a complete uninstall and reinstall try opening iTunes in safe mode (hold down CTRL+SHIFT) as you start iTunes, then going to Edit > Preferences > Store and turning off Show iTunes in the Cloud purchases. You may find iTunes will now start normally.
tt2

I have the latest version of Firefox yet I am still getting an error message that says photoshop is no longer supported on my platfrom and thereofre it's not downloading.

I have the latest version of Firefox yet I am still getting an error message that says photoshop is no longer supported on my platfrom and thereofre it's not downloading.

Please give a bit more system details. Which OS and version are you on? Is it 32 bit or 64 bit. Try downloading the Creative Cloud App if not already installed from: https://creative.adobe.com/products/creative-cloud. You can choose to install PS from withing this app and need not rely on web page.
Regards,
Anirudh

Support for RAW Video and Image Sequences

Being a stills photographer who moved into video some years back, I'm very interested in the direction Lightroom is going with regards to video support. I haven't tried it yet but I wondered if LR4 supports Red R3D files? And would it perhaps support other future RAW video formats from the likes of Canon and Sony? It would seem like the perfect application, perhaps intergrating with Premiere in a similar way to RedCine with FCP. Be great to be able to log footage, orginize it into bins and do basic colour correction in LR, edit the project in Premiere and re-touch in After Effects.
Another task LR would seem ideally suited to is combining image sequences into timelapse video. Shooting timelapse as an image sequence on a DSLR is pretty much standard practice these days; and I've used LR to colour correct, crop and scale my sequences (before fitting them together in Quicktime) for years now. It would be fantastic to be able to preview the clip and export the video (as DPX, ProRes or DNxHD) from within Lightroom.
These are obviously fairly long term wishes. In the short term though, the video features are pretty much useless to me without support for exporting ProRes and DNxHD files. With this LR becomes a powerful asset manager that could be used to collect together footage from multiple sources/codecs and transcode it all for editing. As mentioned in a previous thred, XML support would make it even more useful in this context. There is definitly a gap in the market for an application than can handle this kind of task well.
With other manufactures floundering or neglecting their professional user base, Adobe would seem poised to take the video post crown. I wonder if Lightroom could be part of the takeover?

As I understand it Andy, its intention is to remain a photographers program, not a videographers program. The basic video features are available for lightweight management of videos coming from digital cameras, but it's not going too much further than that at this point in time. Of course that may change in the future, but we'll all have to wait and see on that one.

Is a 10GB "Clickwheel" iPod still supported by iTunes 8+ and OS X 10.4+

I have a 10GB clickwheel iPod that I've been trying to update just to use for some simple mp3 spoken word files and a handful of songs. Not trying to load entire iTunes library on it. Is the clickwheel not compatible with 10.4.11? I've used disk utility to erase and reformat my iPod, used iTunes to restore several times, and unchecked almost all my music just to see if I can get a handful of files to update onto my iPod. I don't care that it's not sleek and brand new, but I certainly hope I can use it still for basic stuff. I'm wondering if it's no longer supported by iTunes 8+ and OS X 10.4+. Does anyone know for sure and can provide an answer? If it should be supported, does anyone have any other suggestions? It seems like it tries to update, but after I see the message that 6 of 100 or 11 of 100 songs have been copied, it just locks up and that is it. Any help would be appreciated.

Doug,
Your iPod should work with no issues on 10.4.11 and iTunes 8+.
When the iPod "locks up" do you hear any clicking noises? Your symptoms sound like the hard drive is having hardware issues.
Here's a trick I used to use to fix the older iPods. It involves opening up the iPod, so if you don't feel comfortable, you might want to go to someone who does.
Take a blade from a box cutter and gently move it along where the plastic meets the metal on the iPod. Use the blade to pry open the iPod from the metal case for the back.
Once you get the iPod out, look towards the bottom of the iPod, and you should see the hard drive with a wide cable attached to it. Take that cable out of the hard drive (gently). Find a Bic pen cap (or something similar) and push it in between the two rows of pins on the cable. Try to make sure the pins are spread apart evenly and all pointing directly out. Once you get that in place, firmly push the cable back into the hard drive and gently put the iPod back together.
You may then want to restore just to be safe, and try loading your music again. I've used this trick on many old iPods to bring another couple of years of life into them. (sometimes this cable comes loose, causing the issues you're describing)
Justin

CD/DVD drive it's not supported by Windows XP and Bios

I've bought a new cd/dvd drive Mat****a Panasonic.
It only work on Windows 2000, it's not supported by Windows XP and Bios, so i can't boot with.

Could you please provide some information (name) about you notebook?
Did you bought this drive or was this drive delivered with the notebook?
If the drive cannot berecognised by BIOS then in my opinion the drive supports wrong master / slave / c-sel settings.
You should know that not all drives are compatible.
The settings cannot be changed because the drive dose not supports any jumpers but only the firmware.

RMAN support of OPS/RAC and ISD's

Can some one point me in the right direction for any white papers, or documentation, on RMAN and its current support of OPS/RAC and/or Intelligent Storage Devices (ISD). I'm trying to do a comparison of RMAN against other third party backup and recovery software and need to find out as much as I can of RMAN support of these architectures. Thanks!

The closest documention I have of RMAN and OPS/RAC is the Oracle Documentation. Take a look in the RAC ADMIN doc. And I talked a little bit about it in an OpenWorld paper from last year. You can find the paper @
http://otn.oracle.com/deploy/availability/pdf/BR_OOW01_213WP.pdf
Bottom line, RMAN supports the clustered environments the same as single instance databases. The rub is the archive log destinations. This is discussed in the RAC documentation.
Thanks, Tammy

Adobe Flash Player will it be supported on an IMac and update ok?

Hi, I am thinking about purchasing an IMac 21", can anyone advise me to if this system will be able to support Adobe Flash Player and if so, are there any problems when trying to update Flash Player? I have tried Googling this but there are so many conflicting comments, it gets confusing. I am also unsure which IMac it will be as in intel or PCC. Help please Janine

Mac System Requirements.
Intel Core™ Duo 1.83GHz or faster processor
Mac OS X v10.6, v10.7, or v10.8
Safari 5.0 or later, Mozilla Firefox 17, Google Chrome, or Opera 11
512MB of RAM; 128MB of graphics memory
http://www.adobe.com/products/flashplayer/tech-specs.html
These are the Sys Requrements in order to run the latest version of Flash. Any Mac will be able to run some earlier version, but it will not be safe. Flash is constantly being updated and patched against exploits.
In order to be able to properly reply to your question, we need to know the Mac model no. you intend buying. But If you meant iMac 21.5", it will be able to run the latest Flash. There were no 21.5" PPC iMacs, and I'm fairly certain there were no 21" PPC iMacs also.

Just upgraded to ios 711 and wifi is grayed out!! tried reboot and network reset. no soap. thank u!

I just upgraded my 4s to ios 711 and wifi is now grayed out and unaccessible. tried network reset and re boot. any ideas? thanks in advance.

diesel,
thank you but have tried the reboot/net reset several times and no change. guess a trip to the apple store in my future?

CVP supports mixed G.711 and G.729

Similar Messages

Maybe you are looking for