CVP to Unity Mailbox issue.

Hi,
I am having a problem with calls going to the correct voice mailbox after coming from CVP when the call originates on a CTI RP.
When the call comes in on a DN associated to the CVP Routing Client, the call goes to the correct Voice Mailbox.
The call flow is:
1) Call hits a dial-peer in the gateway
2) Call goes to CVP
3) ICM executes a script associated to the DN.
4) The call will end in a Precision Queue.
4) If no agent is available the call will then be routed to a Unity pilot number, to be routed to a Voice mailbox associated to the number.
I do this by using Call Routing Rules, that matches the calling number. I've used set the user.microapp.override_cli ECC variable to the dialled number to ensure the CLI matches the calling number for the routing rule in Unity.
The above call flow works correctly and the call goes to the correct Voice mailbox. If I do same and it is an internal call with the caller dialling a CTI Route point the call ends up at unity but is not associated to the correct Voice mailbox.
I assume the user.microapp.override_cli ECC variable does not work when the call comes in via CUCM, is that correct?
If that is correct, how do I make sure the call goes to the correct Voice mailbox?
Thanks,
Bruce

I mean in unity connection Advanced --> Conversation section enable option Use Last (Rather than First) Redirecting Number for Routing INCOMINGCall

Similar Messages

More overstuffed mailbox issues.

My co-workers and I have recently experienced overstuffed mailbox issues and I have been using this forum to figure out what to do. We had been getting "Not downloaded from server" info, and sure enough the mailboxed in question are as large as 1.7 Gb.
Now the only problem is, I don't know how, if at all, the messages from this folder can be retrieved so that some of them can be saved. Ideally, we would like to delete most of the messages but keep the most recent in an active mailbox for searching purposes. Then we would be dilligent in the future about deleting old work to avoid this in the future.
But what can I do right now? I read something about a "Breaker Script" but I don't know how to get it, or what the exact procedure for using it would be.
Please help- thank you, thank you, thank you!

Allan,
Thanks, this worked perfectly! Is it possible, though, that using this script might make the split mailboxes, or maybe the Mail program in general, run more slowly? This seems to be happening to me today, but it may be unrelated.
Thank you again,
Maren

VM Mailbox issue

Dear Team,
Sometime I am facing issue with VM mailbox while importing to unity server , when i assign VM proofile to extension in device profile and trying to import in unity connection server it does not display and in that case i have to create mailbox manually.
i unable to uinderstand what could be the cause but its a issue
Please help.
Regards
hari

When you say "importing" is this through LDAP?
are you saying this sometimes works, where other users you cant import through that same LDAP scheme?
Only thing that I can think of is that you have applied some custom filter in Unity that prevents a certain user from being imported.
for the rest, like Chris mentioned, there is no correlation between the 2.

Mailbox Issues in New Databases in DAG

Ran across a strange problem after moving mailboxes into 2 new Databases in DAG. We have a 2 Server DAG that
had 2 existing DBs. We created 3 additional DBs and planned on moving all MBs over to reclaim space from the older DBs. After moving 30 or so Mbs to the new Databases we found that while mailflow functioned, we could not access any shared mailboxes or mailboxes
that had full control permissions could not be added. Users that had been moved but had shared MBs on another DB in Outlook would get error messages that Folders could not be expanded or Exchange Server was unreachable, all while mail flow was functioning.
Moving these users back to the original DBs solves the issue.
Any ideas what could be happening to the new DBs added to the DAG? The DBs were mounted and copies were healthy.

Hi ocean,
Thank you for your question.
Did you rebuild profile to check if the issue persist after we move mailbox to new DB?
Are there multiple DCs in your organization? And please make sure sync is no problems between DCs.
After we move mailbox, we could check if shared permission or Full Access Permission is missing on recipient mailbox.
We suggest we post the entire error information to
[email protected] for our troubleshooting.
If there are any questions regarding this issue, please be free to let me know.
Best Regard,
Jim
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected]
Jim Xu
TechNet Community Support

Mail rebuild mailbox issue with Gmail

I set up Mail 4.6 to receive and send e-mails to and from Gmail as per the instructions on the Gmail site and used additional information on this forum.
What is happening is whenever I rebuild the gmail folder it downloads again all the files I have deleated. I rebuild after deleting a lot of Spam and e-mails I no longer need.
As recommended the account is set as a imap account.
Under the mailbox tab it is set:
DRAFTS: Store draft messages on server - box not checked
SENT: Store sent messages on server - box not checked
           Delete message: dropdown set to: One day old
JUNK: Store Junk messages on server - box not checked
          Delete message: dropdown set to: One day old
TRASH: Move deleted message to the Trash mailbox - box is checked
             Store deleted messages on the server: - box not checked
             Permanently erase Delete message when: dropdown set to: One day old
Under the Advance tab it is set:
Enable this account - box is checked
Include when automatically checking for new messages - box is checked
Compact mailboxes Automatically - is greyed out - box is checked
Keep copies of messages for offline viewing: dropdown set to: All messages and their attachments
I am not sure is this last item of 'Keep copies of messages for offline viewing' refers to the the Gmail server or the mail box - if it is the gmail server then I guess Mail is just syncronising with this; thus any mails I delete will be down loaded again. ((All the other mail servers I use I set under Advance tab to 'Remove copy from server after retrieving message' - but this option is not shown for gmail.
Two things are happening:
a) When I delete files in the Mail, Gmail folder the next time I rebuild the mail box I get 1000 + emails down loaded; even though I may only have deleted 30 or so.
b) At other time mail will show downloading e-mails in the blue download indicator, but no new emails appear.
Would welcome some direction on how to resolve these issues; thank you.

The issue with g-mail became cronic. Now I can't delete e-mails received to my gmail account.
When I try to delete emails in the gMail or Mail inbox the following message is show.
The Message could not be removed to the mailbox (null)
The destination mailbox "(null)" does not allow messages to be moved to it.
This started after following the recomendation I found in the forum to sync gmail folders to the Mail - folders.
I am looking for solution to get back to the original condition that while not what it should be it is better than now.
Was hoping for solution were I wouldn't have to delete gmail account from mail then start again.
Any ideas welcome as I would like to delete emails in the gmail folders in Gmail without logging into Gmail every time.
Thank you

Exchange 2010 /hosting shared mailbox issue

Hello everyone.
I had an issue come up in our Exchange 2010 with /hosting switch deployment (currently at SP2).
We have several organizations and shared mailboxes configured and working on some. We add Full access permissions via Powershell + Send as rights and it auto configures and works just fine.
Last week though, one of several people that uses a specific shared mailbox started getting the error: "Unable to open your default e-mail folders. The Microsoft Exchange Server computer is not available. Either there are network problems or the
Microsoft Exchange Server computer is down for maintenance." (Error ID: 300)
The other users can still work just fine. Configuring the account in another PC shows the same problem (so it's not the local profile).
Creating 2 users, giving nr1 full access to nr2 generates the same error.
In another org though, i was able to give full access to another acount to an existing user and it worked (although the auto-mapping didn't, had to add it manually)
I'm out of ideias. Any sugestions?
EDIT: Did a couple more tests on another Org. On this one everything works with the shared folder access with old and new accounts but strangely the auto-mapping doesn't.
It seems that this is an issue with the mapping.

Hi,
From your description, I recommend you manually update or create your Outlook profile with RPC encryption and check the result. Here is the steps on Outlook 2007 for your reference:
1. Select your profile, and then click Properties, click E-mail Accounts.
2. Select the Microsoft Exchange Server account, and then click Change.
3. In the dialog box that contains your mailbox server and user name, click More Settings.
4. In the Microsoft Exchange Server dialog box, click the Security tab.
5. Click to select the Encrypt data between Microsoft Office Outlook and Microsoft Exchange check box, and then click OK.
6. Click Next, and then click Finish.
For more information, here is a kb for your reference.
Connection issues and error messages in Outlook for a mailbox on a server that is running Exchange Server 2010
http://support.microsoft.com/kb/2735060
Hope this can be helpful to you.
Best regards,
Amy Wang
TechNet Community Support

Mailbox Issue - Won't Delete ANY mail

Hi there,
I seem to have an issue with Mailbox on my MacBook Air. Please note: I did NOT have the issue on my iMac, before I sold it and reset it. Both Mailbox accounts were set up exactly the same.
I have a hotmail account which I have set up through Mailbox. I can send and receive with no issues at all. The only thing I can't do is delete the mail. I have over 15,000 junk emails and can't delete them. It's exactly the same with my Sent and Trash folders. I like a nice clean Mailbox - this isn't good for my OCD!
Regards,
James

Go to Mail > Preferences > Accounts and under the Advanced tab for the account preferences, is "Remove copy from server after retrieving a message" selected and if so, what is your selection below for removing messages from the server when downloaded by the Mail.app?

Lion and Mailbox issues

Hi!
I'm recently new to Apple, having just bought a Mac Air. I've configured Mailbox because I hate using the service provider sites to deal with my email, preferring a simple, no nonesense email service without instant messager, flashing lights emotions and other hype. Unfortunately my Mailbox seems to want to retrieve my entire history of sent messages from my configured email accounts and even more annoying is that I seem to have to keep deleting the same messages from my trash before they finally die! The other curious issue is that I sometimes find I have several copies of a sent message in my draft folder.
Is this just happening to me? Is there a way of keeping my mailbox under control?
Alan

I have the same issue.
Safari would stall and sometimes stop responding without any reason.
Three things seems to help.
1. Stop automatic graphics card switching (if you have discreet card). Could be issues with graphics drivers not knowing "how" to render a web page when moving from program to program.
2. Turn off automatic brightness control.
3. When Safari crawls, turning of HOVERZOOM usually brings Safari back to normal. I now have this off and seems to be helping a lot.
Mountain Lion 10.8.1 on MacBook Pro
- Landing Gear

Exchange mailbox issues

Earlier today my Exchange mailbox stopped working with the error message 'Cannot Get Mail. The connection to the server failed.'
Our IT department has confirmed that the Exchange server is working correctly, and I'm able to access my emails on my iMac and Macbook. I can also access them via the Exchange remote web link so it's definitely not the server.
I've since updated to iOS 6.1.3 which hasn't resolved the issue.
I've deleted the mailbox and added it again a dozen times. And I've switched the phone on and off about 10 times at various stages of the delete/add process.
Now, when I try to add it again, I get the error message 'Exchange Account. Unable to verify account information.'
Does anyone have any ideas?
Thanks

Are you trying to do this while on cellular data or wifi? If cellular, which carrier... I've read ppl have had problems with Verizon when trying to do this but it's intermittant.
If wifi, is it corporate or your home wifi? Some corporate wifi's block access to exchange mail (mine does) so we have to use corporate desktop email to log conversations.

500 unexpected error : Editing Resource mailbox Issue

Not able to edit resource mailbox in 2013. Issue is not for all resource mailbox only for few resource mailbox's it gives me error 500 unexpected error . Request could not be completed. any idea we are migrating from ex2007 to 2013 When we create new resource
mailbox in Ex2013 there is no issue
Version of Exchange 2007 sp3 roll12, Ex2013with rollup 4 . All resource mailboxes are on Ex2013

Hi,
Could you perform other operations in EAC?
You said that issue was not for all resource mailbox, only some resource mailboxes were affected. If that is the case, I recommend you compare these affected resource mailbox with other normal mailbox and check if there is any difference between them.
If possible, I recommend you move a resource mailbox to a different mailbox database to check result.
Best regards,
Belinda Ma
TechNet Community Support

How can I set up Unity mailbox to deliver messages to email mailbox?

Unity Newbie! Where do I configure a voice mailbox to deliver messages to user's email mailbox?

Andrea,
The previous post simply alludes to the fact that Unity doesn't have a built-in mailstore - instead it relies on Exchange (or in some cases, Domino). Unity can be set up in a Voicemail Only configuration or Unified Messaging configuration. If you have Unity, AD, and Exchange installed all on one box then this is usually indicative of voicemail only. In other words, your Unity server is also a domain controller and Exchange server in a standalone domain used just for itself. When you create subscribers, an associated AD and Exchange account are created but within the domain associated with Unity (not the domain users log into so the users are only aware of the phone login credentials). In Unified Messaging, your Unity would be a MEMBER of an existing AD domain and would integrate with a corporate Exchange server or cluster. In this configuration, the account associated with a subscriber is the account they use everyday - in other words, their voicemail resides in their Exchange inbox that they connect to via Outlook.
My guess is that you have voicemail only configuration today but are looking to do 1 of 3 things:
1) Unified Messaging - voicemail is actually integrated with your corporate Exchange and all voicemails natively reside in the inbox
2) Mail Relay - voicemail messages are relayed from the existing Unity to an email address configured for a user
3) Integrated Messaging - user can configure an IMAP folder in their email client and have access to voicemail from within a separate mailbox in the client
Which sounds like your requirement? If you have more questions, just ask.
Hailey
Please rate helpful posts!

Iphone 4 Mailbox Issues

Over the last day or so the mailbox has been not only super slow but continuously locks up crashes. It hasn't done this until yesterday which seems kind of crazy since nothing has changed on the phone. I reset the network settings, cleared the cache, cookies and all of that even though it has nothing to do with it. It still takes forever to download email, display it, or anything. I has been taking me three attempts to get my email. Any ideas?

If you are using cell data (not WiFi) it could be that AT&T has a temporary network issue in your area. Go to a wifi hotspot and see if that fixes it.
If you are using wifi, try resetting your router.
Phil

Mailbox issue - Symbol - Clock?

My inbox has a symbol next to it that looks like a clock (maybe a pie with a slice missing).... I cannot retrieve mail or send mail? I cannot find anything about this symbol....
I get this error message periodically.....
Some actions taken while the account “NC Fat Boy” was offline could not be completed online.
Mail has undone actions on some messages so that you can redo the actions while online. Mail has saved other messages in mailbox “On My Mac” in “On My Mac” so that you can complete the actions while online.
Additional information: The connection to the server “imap.gmail.com” on port 993 timed out

That symbol is indicating that it is trying to sync with the server.
It can't seem to talk to the gmail account, so it can't finish syncing.
When Mail can't talk to gmail, I will open up a browser and log into gmail from there. That seems to reset something on the gmail server so Mail can connect again.

Mail from Excel using a Shared Mailbox issue

Hello,
We have Office 365 running with several shared mailboxes. We configured the value DelegateSendItemsStyle so when you send an email it will be placed inside the shared mailbox send item folder. (See KB:
http://support.microsoft.com/kb/2181579). So far so good.
When we send directly from an Office application like Excel (File -> Share -> E-mail -> Send as Attachment), in the new email window we change the From field to a shared mailbox, type our text and send the mail. Now the file will be placed
inside the users send items folder.
Somehow when we mail directly from Word/Excel the DelegateSendItemsStyle gets overruled and ignored. When we change the shared mailbox to a payed one with a license, add the box as a second Exchange account and send the mail then, everything is ok and the
mail will be placed inside the shared mailbox send items folder. As you might understand, with 25 shared mailboxes it is a waste of money to license them all.
I contacted Microsoft Office 365 support, and this is outside of their support scope.
Any ideas how we can fix this?
Thanks in advance.
Kind regards,
Max

Hi,
Please read the kb 2181579 again, we can find the following information:
The functionality is available only when the Exchange account is set to
Use Cached Exchange Mode. The DelegateSentItemsStyle registry value does not affect an Exchange account that is configured in Online mode.
When you said "add the box as a second Exchange account", did you mean "additional Mailbox"?
Go to File -> Account Settings -> Account Settings -> Double click on your account name -> More Settings -> Advanced -> Make sure "Use Cached Exchange Mode" and "Download shared folders" have both been ticked -> OK.
Kindly check the result.
Thanks,
Melon Chen
Forum Support
Come back and mark the replies as answers if they help and unmark them if they provide no help.
If you have any feedback on our support, please click
here

CVP 4.1 Sigdigits Issue

Hi
I have a CVP 4.1 with Split PSTN/VXML Gateways and have enabled sip.sigdidits feature to strip off the significant digits to route calls to specific VXML Gateways.
I have a SIP Trunk pointing towards the Call server with a prefix of 4 digits. These digits are discarded and the DNIS is sent to the ICM to invoke the Appropriate Script. The Script uses a Send2VRU with NVRU Label as 77777 which is returned back to the Call server.
The call server also has a Local route specified as 4 Digit Prefix + NRVU Label pointing to the VXML Gateway. The VXML gateway has a Voip Dialpeer that matches the Digits sent by the call server ie. Prefix Digits + NVRU Label + CorrID and triggers the Bootstrap.tcl
The problem we are facing is that the VRU Leg never engages and disconnects with an Error 38 (network Outage)
THe call server logs indicate there is a problem with DN Routes or Gateway Dial-peers, however, everything seems perfectly fine to me.
I am not using any SIP Proxy server, any help would be much appreciated.
Attached are the call server logs.

There have been a few posts here on SIP.sigdigits (I've been in some of them) so you may want to do a search and check them out.
Let's see. I don't see anything obviously wrong, but let's go over it.
CVP is configured with SIP.sigdigits and the value = 4.
The VOIP dial peer towards CVP prefixes 4 digits before sending it to CVP. Let's assume you prefix "8888". Your setting on this dial peer is to send it directly to the SIP Back-to-Back User Agent on CVP using ipv4:a.b.c.d:5060.
When the call arrives at CVP, it strips off 4 digits - i.e. "8888", and sends the resulting DNIS up to ICM through the PG. This starts the ICM script, and hits the "Send to VRU" node. The script pauses and returns the label configured on the Type 10 NVRU for the CVP routing client. You say that this is "77777".
Your label "77777" looks a bit odd. The length is 5. I assume you mean to do this, and have your CVP configured with a DNIS length of 5. True?
This is not as is recommended by Cisco. Normally, one makes this length 10 and you should have a label like "7777777777".
Anyway, CVP gets this label, prepends the sig digits it saved ("8888") and looks for a static route, since you don't have an Outbound Proxy.
You have a static route that catches "888877777" and sends it to the appropriate voice gateway.
Now, on the VXML gateway, you have a dial peer here that catches "888877777T" and tries to run the bootstrap. It sends the complete number back to CVP, and it again applies SIG.digits and strips off "8888", so it looks on "77777" to find the correlation ID.
The only thing that bugs me is the NVRU label.
One thing you say that I can't follow is "I have a SIP Trunk pointing towards the Call server with a prefix of 4 digits."
Are you speaking of a SIP Trunk in Call Manager? This is for getting the call to the agent, and because of SIP.sigdigits, the label returned will be "8888".
Assume all agent extensions are 5 digits.
You need to configure this trunk with significant digits = 5 (it counts from the right hand side). It's not that it discards digits, especially the SIP.sigdigits prepended - it just looks from the RHS and counts 5.
You will need this to get the call to the agent, but not for making the call queue on the gateway; so I wonder why you mention this.
Regards,
Geoff

CVP to Unity Mailbox issue.

Similar Messages

Maybe you are looking for