CWA with WLC Firmware 7.0.228 and ISE 1.1.1

Hi,
Does Cisco ISE central web authentication supports on WLC version 7.0.228 ?
My customer has many access points which are support only for firmware code 7.0.228.
Cisco ISE version 1.1.1
WLC 5500 Series but the existing access point is cannot support to 7.3
Thanks,
Pongsatorn Maneesud

Tarik is correct, you need 7.2.x and later to use CWA with ISE. Here is a general summary of features supported on ISE on 7.0 and 7.2 versions of code:
Scenarios                                                          WLC 7.0                                             7.2
802.1X Auth                                                     Yes                                                      Yes
802.1X + Posture                                            Yes                                                      Yes
802.1X + Profiling                                           Yes                                                      Yes
Web Auth + Posture                                       No *                                                   Yes
Web Auth + Profiling                                      Inventory only *                         Yes
Central Web Auth(CWA)                               No *                                                   Yes
Local Web Auth(LWA)                                   Yes                                                      Yes

Similar Messages

Guest wireless with WLC 2504, Catalyst 4510R+E and ASA 5510

I need to add guest (internet only) wireless to our existing internal wireless and am looking for advice as to the best practice configuration. Existing infrastructure as follows:
WLC 2504
1142 LAPs
4510R+E
ASA 5510
Existing configuration as follows:
WLC management interface and APs addressed on the 192.168.126.0 /25 network
Internal WLAN mapped to the management interface
Management interface VLAN ID 0 (untagged) and dynamic AP management enabled
WLC port 1 (only) connected to 4510 via trunk with native VLAN set to 7 and allowed VLAN set to 7
4510 connected to ASA inside interface (security level 100)
Switchport on 4510 connected to ASA configured as switchport access VLAN 99 (our internet VLAN)
ASA inside interface NOT configured for subinterfaces and is addressed on the 192.168.121.0 /25 network
What is the best way to add guest wireless to our existing configuration?
Note: I need the guest wireless to be filtered by Websense as our internal wireless is
Any advice would be greatly appreciated!

Thank for the reply Scott. The configuration recommendations from Yahya did not work. I set up as he recommended and also added a dhcp scope on the wlc. Client gets dhcp but cannot even ping the wlc much less anything else. Yahya stated above to configure port 2 on the wlc to an access port on my 4510. Aren't all connections from the wlc supposed to be trunk links to the switch? Shouldn't I just leave the management interface on the wlc untagged and add a dynamic interface for each wlan and tag it with the approriate vlan id? And then leave the (one) physical connection on the wlc (port 1) connected to a trunk link on the 4510 that allows the required vlans?
Any input would be greatly appreciated...
JW

Windows 8.1 compatibility with WLC v7.0.98.218 and DELL DEVICES

hello,
We have a lot wlc (4400, WiSM, WS-C3750G-24PS and 5500) running on version 7.0.98.218.
Windows 7 and Windows 8 clients are able to connect to the WiFi, which has Windows 8.1 can no longer connect.
we tested two WLAN's, one with security policy: [WPA2] [Auth (802.1X)] and another with [WPA2] [Auth (PSK)], MAC Filtering
in any of the WLAN's the clients with Windows 8.1 did not bind (cannot connect).
the outup obtained is attached
one of the devices which are having problems is a dell laptop E5430.
We've update the wireless card drivers ... according to the dell ... I did downgrade for old version... upgrade to last versions given by broadcom ... but still the problem
can you help me ?!?
Regards,
Tiago Marques

To enable that your network is ready for 802.11w and Windows 8 ensure that you are running the latest Cisco Unified releases in your wireless controller network.
Please find the link :-
http://www.my80211.com/home/2012/10/19/bug-cscua29504-upgrade-that-code-if-you-want-windows-8-to-wo.html

IMAC can't find N network with TC firmware 7.4.1 and 7.4.2

Hello, I have a problem since I upgraded my TC from 7.3.2 to 7.4.1 and 7.4.2.
both my two IMACs can't find the TC N network, only if I downgrade to 7.3.2 they actually find and connect to the TC N network.
please let me know if the only solution is not to upgrade the firmware.
thanks
Fabrizio

Same here: 7.1.1 works but 7.2.1 & 7.3.1 do not with the same symptoms.
In fact there are now several threads reporting the same loss of internet connectivity. Happily reverting to 7.1.1 restores connectivity.

When install printer driver via Bonjour, what information OS/CUPS communicate with printer firmware to auto-detect and find correct PPD to install?

Hi guys,
We are developing printer driver/firmware for Mac OS X 10.5 and up. Right now we have problem that printer firmware fail to be auto detected by Mac OS 10.5 during installation via Bonjour. Could anyone teach me how the communication works between OS/CUPS and printer F/W during the installation via Bonjour? What kind information the two sides exchange?
Any input will be appreciated!

Sorry for the incorrect information. The OS should be Mac OS X 10.4 instead of 10.5

Zen Sleek with PlaysForSure Firmware 2.01.03 and Windows 2

Would someone kindly advise me if this is a viable combination, and will the original Zen Sleek Media Explorer still work.
Thanks and regards
gdl

Some have reported that reloading the firmware will fix the slowness. Gi've that a try and see if it works for you.
As for the file error that you are getting, download the following 3 hotfixes, esp the last one as it speficially fixes this error. The other 2 I suggest you download them just in case to prevent some errors that may appear.
Windows Media Format 9.5 Runtime:
<a href='http://support.microsoft.com/default.aspx?scid=kb;en-us;8922' target=_blank>http://support.microsoft.com/default.aspx?scid=kb;en-us;8922[/url]
DRM performance fix:
<a href='http://support.microsoft.com/default.aspx?scid=kb;en-us;902344' target=_blank>http://support.microsoft.com/default.aspx?scid=kb;en-us;902344[/url]
Fix for large data transfers:
<a href='http://support.microsoft.com/default.aspx?scid=kb;en-us;89536' target=_blank>http://support.microsoft.com/default.aspx?scid=kb;en-us;89536[/url]

WLC 5508 (ver 7.2) and ISE 1.1.2

Ciao,
I found this interesting article:
Dynamic VLAN Assignment with RADIUS Server and Wireless LAN Controller Configuration Example
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml
And I'm wondering if the same configuration will work with ISE 1.1.2.
My needs are:
- one SSID
- according to authentication (for guest: user\pwd in ISE database; for employees certificate or user\pwd M$ AD) moved to a VLAN or another
Ciao e grazie!
Luciano

Philip,
My bad, I apologize for the confusion, they put so many numbers on the back
here this might help.
http://www.cisco.com/en/US/products/ps10315/products_tech_note09186a0080bcb905.shtml

Wireless Guest Access with 802.1X (PEAP/MSCHAPv2) and ISE?

Hi,
I have a setup based on WLC 5508, Catalyst 3750-X and AP3600i.
The WLCs are running 7.3 and ISE is 1.1.1
I'm trying to setup wireless guest access, where the guests connect to a SSID with 802.1X using PEAP/MSCHAPv2.
They should receive their username/password either from a sponsor directly (corporate AD user which prints the credentials) or through a SMS.
The credentials will be created by the sponsor, using the sponsor portal on the ISE.
Now to the questions:
Is it correct that the foreign WLC (i.e. the WLC within the internal corporate network), should be set to no L2 and L3 security on the guest WLAN, to avoid having the foreign WLC contact the ISE and all traffic be forwarded directly to the anchor WLC?
Is it correct that the anchor WLC (i.e. the WLC in the DMZ), should be configured with 802.1X/WPA2 L2 security and the ISE servers as the RADIUS servers on the guest WLAN, to ensure that the client is correctly authenticated/authorized by the ISE?
When a guest logs on, how can I ensure that only one device (MAC address) is allowed per user?
As it is now, a guest is able to log on with (I assume) an unlimited number of devices, using the credentials they have received.
Thankyou very much :-)
Best Regards,
Niels J. Larsen

Hi,
I have a setup based on WLC 5508, Catalyst 3750-X and AP3600i.
The WLCs are running 7.3 and ISE is 1.1.1
I'm trying to setup wireless guest access, where the guests connect to a SSID with 802.1X using PEAP/MSCHAPv2.
They should receive their username/password either from a sponsor directly (corporate AD user which prints the credentials) or through a SMS.
The credentials will be created by the sponsor, using the sponsor portal on the ISE.
Now to the questions:
Is it correct that the foreign WLC (i.e. the WLC within the internal corporate network), should be set to no L2 and L3 security on the guest WLAN, to avoid having the foreign WLC contact the ISE and all traffic be forwarded directly to the anchor WLC?
Is it correct that the anchor WLC (i.e. the WLC in the DMZ), should be configured with 802.1X/WPA2 L2 security and the ISE servers as the RADIUS servers on the guest WLAN, to ensure that the client is correctly authenticated/authorized by the ISE?
When a guest logs on, how can I ensure that only one device (MAC address) is allowed per user?
As it is now, a guest is able to log on with (I assume) an unlimited number of devices, using the credentials they have received.
Thankyou very much :-)
Best Regards,
Niels J. Larsen

Problems with EFI Firmware Update to 1.5 for mid 2010 Mac Pro, and sleep issues

Hello to the community, I have run into an annoying issue.
I need to update the EFI firmware on my 8 core mid-2010 Mac Pro. I downloaded the EFI update from the apple website from here : http://support.apple.com/kb/DL1321
But everytime I download it, as I click to install, it gives me the message:
Alert
This software is not supported on your system.
But clearly this is the correct EFI for my computer. I tried burning the Firmware restoration onto a CD from here:
http://support.apple.com/kb/DL1320
But the computer did not respond the way it said it should (with the 3 flashes/beeps etc.) and have the optical drive open for the CD.
So I'm completely stuck.
*Also my Mac Pro had issues with sleep, when I put it to sleep, sometimes when I try to bring it back, it restarts itself, and other times, it just turns itself on and the monitor screen remains black, so I have to hit the power button to turn it off then back on again. This only happnens when the computer has been put to sleep for a slightly extended period of time, roughly 20mins +, sometimes longer. I was trying to solve this problem by first updating the firmware because I think it could be related to that, but I've had this problem with the firmware so I couldn't find out. This is actually the bigger problem for me because it will affect my work. I am currently using an iMac while I fix up this mac pro.
I'm a music composer so I've upgraded many aspects of my system due to work. I have a 1TB Samsung 840 evo SSD, 2 seagate 2 TB HDD, and 1 WD 1TB HD (the original one in the mac pro), along with 32 GB of RAM. So my only problems are the firmaware and the weird activity when the computer is put to sleep.
Some help would be greatly appreciated!
I'm running OS X Mavericks 10.9.2
mid-2010 Mac Pro
8 core processor (2 X 2.4gHz)

According to this article, your EFI firmware is up to date:
Computer
Model identifier
EFI Boot ROM version
SMC version
Mac Pro
Mac Pro (Late 2013)
MacPro6,1
MP61.0116.B04 (EFI 2.0)
2.20f18 (SMC 2.0)
Mac Pro (Mid 2010)
MacPro5,1
MP51.007F.B03 (EFI 1.5)
Mac Pro (Early 2009)
MacPro4,1
MP41.0081.B07 (EFI 1.4)
Mac Pro (Early 2008)
MacPro3,1
MP31.006C.B05 (EFI 1.3)
Mac Pro (8-core)
MacPro2,1
MP21.007F.B06 (EFI 1.2)
1.15f3 (SMC 1.1)
Mac Pro (Original)
MacPro1,1
MP11.005C.B08 (EFI 1.2)
1.7f10 (SMC 1.1)
EFI and SMC firmware updates for Intel-based Macs

ISE 1.2 With WLC and AD

Hi everyone,
What is the steps and Procedure implement Wired and wireless authentication with ISE, WLC and AD for a LAB environment. currently the following are done.
The wireless network is configured with 2 SSID (Staff and Guest)
Active Directory, DNS, DHCP, and NTP configured & synced.
ISE and AD running on C220 VMs, and WLC is 5760 Appliance.
Please provide your thoughts and assistance.
Regards

You have to implement dot1x and radius between your NAD and ISE device.
Using the switch 3850, that are the steps:
username RADIUS-HEALTH password radiusKey1 privilege 15
aaa new-model
aaa authentication login default local
aaa authentication dot1x default group radius
aaa authorization network default group radius
aaa authorization auth-proxy default group radius
aaa accounting update periodic 5
aaa accounting auth-proxy default start-stop group radius
aaa accounting dot1x default start-stop group radius
!this password will be used to communicate with ISE and to verify reachability
!between ISE and Switch
aaa server radius dynamic-author
client 172.16.1.18 server-key 7 radiuskey
client 172.16.1.20 server-key 7 radiuskey
ip domain-name lab.local
ip name-server 172.16.1.1
dot1x system-auth-control
interface GigabitEthernet1/0/3
switchport mode access
switchport voice vlan 50
switchport access vlan 10
ip access-group ACL-ALLOW in
authentication event fail action next-method
authentication event server dead action authorize voice
authentication event server alive action reinitialize
authentication host-mode multi-auth
authentication open
authentication order dot1x mab
authentication priority dot1x mab
authentication port-control auto
authentication periodic
authentication timer reauthenticate server
authentication violation restrict
mab
dot1x pae authenticator
dot1x timeout tx-period 10
spanning-tree portfast
ip access-list extended ACL-ALLOW
permit ip any any
!the comm between radius and ise will occur on these Port
ip radius source-interface Vlan100
logging origin-id ip
logging source-interface Vlan100
logging host 172.16.1.20 transport udp port 20514
logging host 172.16.1.18 transport udp port 20514
ip radius source-interface Vlan100
logging origin-id ip
logging source-interface Vlan100
logging host 172.16.1.20 transport udp port 20514
logging host 172.16.1.18 transport udp port 20514
snmp-server community ciscoro RO
snmp-server community public RO
snmp-server trap-source Vlan100
snmp-server source-interface informs Vlan100
radius-server attribute 6 on-for-login-auth
radius-server attribute 8 include-in-access-req
radius-server attribute 25 access-request include
radius-server dead-criteria time 10 tries 3
radius-server vsa send accounting
radius-server vsa send authentication
!defining ISE servers
radius server ISE-RADIUS-1
address ipv4 172.16.1.20 auth-port 1812 acct-port 1813
automate-tester username RADIUS-HEALTH idle-time 15
key radiusKey
Please be sure that NTP servers and time are synchronized.
enable dot1X on windows machine, or using cisco NAM.
you can enable debugging on aaa authentication to see the events.
you have to create this user on ISE (RADIUS-HEALTH).
3850#test aaa group radius username password new-code
and observe the result. You are supposed to have user authenticated successfully.
You Must also have define these device in ISE on the radius interface.
ip radius source-interface ..... use this interface ip address to define Ip address of the NAD device in ISE.
administration-->network resources -->Network Devices-->Add
input the name
input the Ip address for radius communication
select the authentication settings and field the corresponding shared secret radius key
select snmp settings and select version 2c.
snmp community : ciscoro
you can customize the polling interval if you want and that all.
you are supposed to received message communication between your NAD and ISE.
After you can do the procedure for WLC device.
I will fill it after you have passed the first steps (3850 authentication).

Wireless guest access with CWA and ISE using mobility anchor

My team is trying to demo wireless guest access using CWA with an ISE server. We appear to be hitting an issue when combining this with mobility anchoring.
When we don't use a mobility anchor the authentication goes off without a hitch seemingly proving that the ISE configuration is sound. The test laptop associates and gets redirected, auths, moves to the RUN state and access to the network is granted.
When the mobility anchor is enabled, the test laptop does get redirected, authentication is successful, but the process does not fully complete, as on the foreign controller the user is in RUN state whereas on the anchor the user is still stuck at CWA required.
Now, I've read the L2 auth occurs between the foreign controller and ISE, and the L3 auth occurs between the anchor controller and ISE, but this does not appear to borne out in packet captures of the process where both parts of the auth seems to go to and from the foreign controller and ISE.
I'm curious to know if anyone else has come across this issue, or has ideas where I should be looking in the config or debugs to find the root cause.
When setting up the controllers and ISE this guide (linked below) was used and the controllers are 2504 controllers on 7.5 series software and ISE is on the latest 1.2 patches:
http://www.cisco.com/en/US/products/ps11640/products_configuration_example09186a0080bead09.shtml
To me it seems to be mobility related, but the authentication flow does seem to be off compared with what the guide says.

FOREIGN
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Adding mobile on LWAPP AP 0c:d9:96:ba:7d:20(1)
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Association received from mobile on BSSID 0c:d9:96:ba:7d:2f
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Global 200 Clients are allowed to AP radio
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Max Client Trap Threshold: 0 cur: 0
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Rf profile 600 Clients are allowed to AP wlan
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 0 Quarantine Vlan 0 Access Vlan 0
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Re-applying interface policy for client
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2164)
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2185)
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 255 on mobile
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 In processSsidIE:4565 setting Central switched to TRUE
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 In processSsidIE:4568 apVapId = 1 and Split Acl Id = 65535
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 Applying site-specific Local Bridging override for station 00:1e:c2:c0:96:05 - vapId 1, site 'AP-Group-CHEC.default', interface 'management'
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 Applying Local Bridging Interface Policy for station 00:1e:c2:c0:96:05 - vlan 84, interface id 0, interface 'management'
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 processSsidIE statusCode is 0 and status is 0
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 processSsidIE ssid_done_flag is 0 finish_flag is 0
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 STA - rates (8): 140 18 152 36 176 72 96 108 0 0 0 0 0 0 0 0
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 suppRates statusCode is 0 and gotSuppRatesElement is 1
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 apfProcessAssocReq (apf_80211.c:7830) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from Idle to AAA Pending
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 Scheduling deletion of Mobile Station: (callerId: 20) in 10 seconds
*radiusTransportThread: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Username entry (00-1E-C2-C0-96-05) created for mobile, length = 253
*radiusTransportThread: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Username entry (00-1E-C2-C0-96-05) created in mscb for mobile, length = 253
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Received SGT for this Client.
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Redirect URL received for client from RADIUS. Client will be moved to WebAuth_Reqd state to facilitate redirection. Skip web-auth Flag = 0
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Resetting web IPv4 acl from 255 to 255
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Resetting web IPv4 Flex acl from 65535 to 65535
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 84
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Re-applying interface policy for client
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2164)
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2185)
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 0 on mobile
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Inserting AAA Override struct for mobile
MAC: 00:1e:c2:c0:96:05, source 2
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Initializing policy
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 AUTHCHECK (2) Change state to L2AUTHCOMPLETE (4) last state AUTHCHECK (2)
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Not Using WMM Compliance code qosCap 00
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 L2AUTHCOMPLETE (4) Plumbed mobile LWAPP rule on AP 0c:d9:96:ba:7d:20 vapId 1 apVapId 1 flex-acl-name:
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 L2AUTHCOMPLETE (4) Change state to DHCP_REQD (7) last state L2AUTHCOMPLETE (4)
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfMsAssoStateInc
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from AAA Pending to Associated
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfPemAddUser2:session timeout forstation 00:1e:c2:c0:96:05 - Session Tout 1800, apfMsTimeOut '1800' and sessionTimerRunning flag is 0
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Scheduling deletion of Mobile Station: (callerId: 49) in 1800 seconds
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 1800
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Sending Assoc Response to station on BSSID 0c:d9:96:ba:7d:2f (status 0) ApVapId 1 Slot 1
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfProcessRadiusAssocResp (apf_80211.c:3066) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from Associated to Associated
*DHCP Socket Task: Jan 28 23:04:59.567: 00:1e:c2:c0:96:05 DHCP received op BOOTREQUEST (1) (len 308,vlan 84, port 13, encap 0xec03)
*DHCP Socket Task: Jan 28 23:04:59.567: 00:1e:c2:c0:96:05 DHCP (encap type 0xec03) mstype 0ff:ff:ff:ff:ff:ff
*DHCP Socket Task: Jan 28 23:04:59.567: 00:1e:c2:c0:96:05 DHCP dropping packet due to ongoing mobility handshake exchange, (siaddr 0.0.0.0, mobility state = 'apfMsMmQueryRequested'
*DHCP Socket Task: Jan 28 23:05:01.523: 00:1e:c2:c0:96:05 DHCP received op BOOTREQUEST (1) (len 308,vlan 84, port 13, encap 0xec03)
*DHCP Socket Task: Jan 28 23:05:01.523: 00:1e:c2:c0:96:05 DHCP (encap type 0xec03) mstype 0ff:ff:ff:ff:ff:ff
*DHCP Socket Task: Jan 28 23:05:01.523: 00:1e:c2:c0:96:05 DHCP dropping packet due to ongoing mobility handshake exchange, (siaddr 0.0.0.0, mobility state = 'apfMsMmQueryRequested'
*mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 DHCP_REQD (7) State Update from Mobility-Incomplete to Mobility-Complete, mobility role=ExpForeign, client state=APF_MS_STATE_ASSOCIATED
*mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 apfMsRunStateInc
*mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 DHCP_REQD (7) Change state to RUN (20) last state DHCP_REQD (7)
*mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 RUN (20) Reached PLUMBFASTPATH: from line 5793
*mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 RUN (20) Adding Fast Path rule
type = Airespace AP Client
on AP 0c:d9:96:ba:7d:20, slot 1, interface = 13, QOS = 0
IPv4 ACL ID = 255, IPv6 ACL ID = 255,
*mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 RUN (20) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 15206 Local Bridging Vlan = 84, Local Bridging intf id = 0
*mmMaListen: Jan 28 23:05:02.363: 00:1e:c2:c0:96:05 0.0.0.0 RUN (20) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
*pemReceiveTask: Jan 28 23:05:02.364: 00:1e:c2:c0:96:05 Set bi-dir guest tunnel for 00:1e:c2:c0:96:05 as in Export Foreign role
*pemReceiveTask: Jan 28 23:05:02.364: 00:1e:c2:c0:96:05 0.0.0.0 Added NPU entry of type 1, dtlFlags 0x4
*pemReceiveTask: Jan 28 23:05:02.364: 00:1e:c2:c0:96:05 Skip Foreign / Export Foreign Client IP 0.0.0.0 plumbing in FP SCB
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP received op BOOTREQUEST (1) (len 308,vlan 84, port 13, encap 0xec03)
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP (encap type 0xec03) mstype 0ff:ff:ff:ff:ff:ff
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP processing DHCP REQUEST (3)
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 0
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   xid: 0xafea6bc9 (2951375817), secs: 5, flags: 0
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   chaddr: 00:1e:c2:c0:96:05
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   ciaddr: 0.0.0.0, yiaddr: 0.0.0.0
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   siaddr: 0.0.0.0, giaddr: 0.0.0.0
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   requested ip: 10.130.98.8
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP received op BOOTREPLY (2) (len 320,vlan 84, port 13, encap 0xec07)
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP processing DHCP ACK (5)
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   op: BOOTREPLY, htype: Ethernet, hlen: 6, hops: 0
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   xid: 0xafea6bc9 (2951375817), secs: 0, flags: 0
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   chaddr: 00:1e:c2:c0:96:05
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   ciaddr: 0.0.0.0, yiaddr: 10.130.98.8
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   siaddr: 10.30.4.173, giaddr: 0.0.0.0
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   server id: 1.1.1.2 rcvd server id: 1.1.1.2
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) DHCP Address Re-established
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Reached PLUMBFASTPATH: from line 6978
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Replacing Fast Path rule
type = Airespace AP Client
on AP 0c:d9:96:ba:7d:20, slot 1, interface = 13, QOS = 0
IPv4 ACL ID = 255, IPv6 ACL ID
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 15206 Local Bridging Vlan = 84, Local Bridging intf id = 0
*DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
*DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 Assigning Address 10.130.98.8 to mobile
*DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 DHCP success event for client. Clearing dhcp failure count for interface management.
*DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 DHCP success event for client. Clearing dhcp failure count for interface management.
*DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 DHCP successfully bridged packet to STA
*pemReceiveTask: Jan 28 23:05:03.889: 00:1e:c2:c0:96:05 Set bi-dir guest tunnel for 00:1e:c2:c0:96:05 as in Export Foreign role
*pemReceiveTask: Jan 28 23:05:03.889: 00:1e:c2:c0:96:05 10.130.98.8 Added NPU entry of type 1, dtlFlags 0x4
*pemReceiveTask: Jan 28 23:05:03.890: 00:1e:c2:c0:96:05 Skip Foreign / Export Foreign Client IP 10.130.98.8 plumbing in FP SCB
*apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 Received SGT for this Client.
*apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 Resetting web IPv4 acl from 0 to 255
*apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 Resetting web IPv4 Flex acl from 65535 to 65535
*apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 AAA redirect is NULL. Skipping Web-auth for Radius NAC enabled WLAN.
*apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 255 on mobile
*apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 Inserting AAA Override struct for mobile
MAC: 00:1e:c2:c0:96:05, source 2
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Setting session timeout 3600 on mobile 00:1e:c2:c0:96:05
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Session Timeout is 3600 - starting session timer for the mobile
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Applying cached RADIUS Override values for mobile 00:1e:c2:c0:96:05 (caller pem_api.c:2307)
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Setting session timeout 3600 on mobile 00:1e:c2:c0:96:05
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Session Timeout is 3600 - starting session timer for the mobile
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Applied RADIUS override policy
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Replacing Fast Path rule
type = Airespace AP Client
on AP 0c:d9:96:ba:7d:20, slot 1, interface = 13, QOS = 0
IPv4 ACL ID = 255, IPv6 ACL ID
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 15206 Local Bridging Vlan = 84, Local Bridging intf id = 0
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Not Using WMM Compliance code qosCap 00
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Plumbed mobile LWAPP rule on AP 0c:d9:96:ba:7d:20 vapId 1 apVapId 1 flex-acl-name:
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Change state to RUN (20) last state RUN (20)
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 apfMsAssoStateInc
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from AAA Pending to Associated
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 apfPemAddUser2:session timeout forstation 00:1e:c2:c0:96:05 - Session Tout 3600, apfMsTimeOut '1800' and sessionTimerRunning flag is 1
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Scheduling deletion of Mobile Station: (callerId: 49) in 3600 seconds
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 3600
*apfReceiveTask: Jan 28 23:05:18.718: 00:1e:c2:c0:96:05 Sending Assoc Response to station on BSSID 0c:d9:96:ba:7d:2f (status 0) ApVapId 1 Slot 1
*apfReceiveTask: Jan 28 23:05:18.718: 00:1e:c2:c0:96:05 apfProcessRadiusAssocResp (apf_80211.c:3066) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from Associated to Associated
*pemReceiveTask: Jan 28 23:05:18.720: 00:1e:c2:c0:96:05 Set bi-dir guest tunnel for 00:1e:c2:c0:96:05 as in Export Foreign role
*pemReceiveTask: Jan 28 23:05:18.720: 00:1e:c2:c0:96:05 10.130.98.8 Added NPU entry of type 1, dtlFlags 0x4

IPod Touch 2G with Firmware 3.1.2 and audiobook troubles

I was using firmware 3.1.1, listening to an audiobook with no issues (audiobook was imported as mp3 files from multiple CD's - the media type was changed in bulk to Audiobook under the options tab). The book flowed fine from mp3 to mp3, in order.
Then I decided to go to 3.1.2 (I also recently updated to Snow Leopard) and the play order of the parts seemed to become random. The files still show up in the audiobook section, but do not play in order, even after renaming them all.
I tried to convert them in bunches to m4b files, and they still play out of order.
Is this an iTunes issue, or an iPod firmware issue? Is there a way to rollback to 3.1.1? I could only find 3.1.2 in my Library>iTunes>iPod Software Updates folder.

I have exactly the same problem although my audiobook playback was messed up by 3.1.1. Spoke to support in local store who suggested rolling back (can't do it either - also not in folder). Also suggested that way to check whether itunes or firmware was at fault was see if playback random in itunes. It isn't so I am assuming that the problem is with the firmware update. All was working fine until I installed 3.1.1 - I hoped 3.1.2 might sort the problem out but no luck. I hope Apple are taking notice of this because I am less than impressed with the accessibility of any support or even interest.

WLC 5508 with version 7.0.98.0 and AIR-LAP1242ag

hi, recently i have deployed wlc 5508 with ap 1262. initially i had trouble with the existing version on the wlc (6..0.199.0) which AIR-LAP1262N-E-K9 was not registering with wlc. i have upgraded the wlc to 6.0.199.4 ver still it was not registering. finally i have upgraded to 7.0.98.0 and all the 40 AP's ( AIR-LAP1262N-E-K9 ) are addedd and its working fine.
Now my issue is, at the same site i have 12 nos of AIR-LAP1242ag autnomous AP's which i need to convert to lightweight ap and register with wlc. where i am stuck currently. after loading the recovery image (c1240-rcvk9w8-tar.123-7.JX9.tar) the ap reboots and can see it register with wlc within seconds contollers pushed the new image and once the ap reboots, never register again.
does anyone has any idea?

After adding the country codes GB and RU.. in my test setup 1242 is registered...i will have it run for couple hours and see the result
ref: below
(Cisco Controller) >show ap uptime
Number of APs.................................... 2
Global AP User Name.............................. Not Configured
Global AP Dot1x User Name........................ Not Configured
AP Name              Ethernet MAC       AP Up Time               Association Up Time
AP1cdf.0f66.79ca     1c:df:0f:66:79:ca 0 days, 00 h 43 m 35 s   0 days, 00 h 42 m 36 s
AP001e.be27.a7e6     00:1e:be:27:a7:e6 0 days, 00 h 16 m 56 s   0 days, 00 h 07 m 15
This issue sorted...thanks

Cisco 3750 with integrated WLC, wpa2 ent, 802.1x and ms IAS.

So first post, I usually figure most of this stuff out. I have this all working with latest firmware etc, but I have more of a MS IAS issue than anything.
The Peap cert used is one generated for my IAS controller, but I have two things... I'd like it to be highly available (if I shutdown Ias#1 it uses ias#2 and has a different certificate as its host name dependent). Also, if I can get a certificate for both IAS servers (using ms cert authority, trusted by all my comp's etc), I'd like it to be more than a one year cert.
Both IAS servers are DC's, so when creating a cert request from Mmc cert snapin for machine, it has the template domain controller and only uses the machine name. I need to make a 2-5 year cert generic for IAS.
Thanks for any help.
Sent from Cisco Technical Support iPad App

There are two thing you could do.
1.) use a GPO to push the certificate from IAS#2 to all your clients.
2.) under the PEAP config, uncheck the validate server certificate box.
With PEAP, the supplicant doesn't 'need/have' to have the server cert, it's an option. When I'm testing, I alwasy uncheck this box. You could test if the clients will failover to the other IAS with the option unchecked.
As for the cert, are both of these devices a CA, or are you using as self genereated cert? If you have multiple IAS, you may want to promote a server to be a CA< and then issue both of these servers a cert from there. Then you only need to have your CA root on the client, instead of each IAS.
HTH,
Steve
Please remember to rate helpful posts or to mark the question as answered so that it can be found later.

An issue with WLC 5508 and 7921 phone

Hello all!
I have a system with WLC 5508 and some 1242 APs. And I use a lot of 7921 phones.
One of 7921 phones was in trouble. It loses registration, disconnect conversations...
I installed the trial WLC and run voice diagnostics.
I saw some of "Potentially degraded QoS in downlink direction because of incorrect packet classification" messages and one "Fair upstream packet loss ratio: 1,2%, which is less than threshold 2.5%"
As I understand all of 7921 phones in these area are affected.
what does it mean? I set up Platinum QoS for voice WLAN. I don't have any qos configuration string for AP and WLC ports on switches...
any ideas?
thanx in advance

Sergey:
There is one application called "WLC Config analyzer". You save your "show run-config" from your WLC in a text file and import it by this application. it will analyze the file for you and tell you what recommendations for voice are missing so you improve them.
When importing a config file you choose what voice clinets you are using, so you need to choose cisco 7921 to it tells you what config improvemetns is needed based on 7921 needs.
Here is the link to download the application:
https://supportforums.cisco.com/docs/DOC-1373
download the latest versoin.
BTW, how many voice/data clients are connected to one AP in that area? if I remember correctly if you are utilizing voice then the max number of clients connected to one AP should not exceed 17. If you have more than this number per AP try to minimize the number of users concurrently connected to the AP then try again.
Hope you'll find the config analyzer useful.
If useful please don't forget to rate.
Amjad

CWA with WLC Firmware 7.0.228 and ISE 1.1.1

Similar Messages

Maybe you are looking for