CWWLSE - IP_Address_Change

Hello,
we get an error message in logs
for wireless clients on our WLSE appliance we cann't explain : event=IP_Address_Change. But we didn't
change any conf...
Any idea ?
Regards,
C.Rolland

An IP Address Change is sent from WDS to WLSE whenever a client's IP address changes and is detected at the AP that the client is registered to.This can be like For example, an IP Address Change event gets produced when a DHCP server assigns an IP Address initially to a client.

Similar Messages

  • CWWLSE-1030-K9 Cisco WLSE Wireless LAN Solution EE 2.13 with AP 1242

    Dear all, my customer has CWWLSE-1030-K9 Cisco WLSE Wireless LAN Solution EE 2.13 with 12 AP1242 (a/b/g) Radio 802.11g in place. Now he will buy additional AP what type of AP can i use because AP 12xx is EOS.

    Hello Dirk,
    AP 1200 is EOS, and customers were encouraged to migrate to 1240 Series (which is also EOS now)
    http://www.cisco.com/c/en/us/products/collateral/wireless/aironet-1200-series/eol_c51-506611.html
    Therefore it is recommended to migrate to Cisco Aironet 1600 or Cisco Aironet 2600 Series.
    http://www.cisco.com/c/en/us/products/collateral/collaboration-endpoints/unified-ip-phone-7900-series/end_of_life_notice_c51-726425.html

  • Upgrade linux Red Hat version 4 to Red Hat version 5 on an appliance CWWLSE-1130-K9

    Hi.
    I have a WCS 5.0 installed on an appliance CWWLSE-1130-K9 to Red Hat Linux 4.0. I need to upgrade to Linux Red Hat version 5 in order to use WCS version 6.0. Does anyone know the procedure to do it?

    You do need to have either your WLSE under warranty or a TAC smartnet contract for support on this device as far as product evolution and upgrades.
    You may have a support contract since you have a WCS.

  • CWWLSE-1130-19-k9

    Hi All,
    While booting Cisco CWWLSE-1130-19-k9 we are getting error saying that GRUB loading, please wait...Error 15. and system reboots. Hence kindly help me to identify what is this error and how can I rectify this problem?
    Thanks and Regards
    Mangesh A. Bhende

    Hi All,
    when i tried to boot the CWWLSE using recovery CD I got below mentioned error. Please help me in resolving this issue.
    hub.c: USB new device connect on bus1/1, assigned device number 2
    INIT: Entering runleveinput0l: 1: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb1:2.0
    bash: no job conEXT2-fs warning: checktime reached, running e2fsck is recommended
    trol in this shell
    hub.c: USB new device connect on bus1/2, assigned device number 3
    input1: USB HID v1.11 Mouse [0461:4d15] on usb1:3.0
    CDROM is hde
    Partitioning the drive: size = 40209120.
    version: Error reading from flash
    version: Error reading from flash
    Error: Version infomation not found in flash.
    md: stopping all md devices.
    flushing ide devices: hda hde
    Restarting system.
    Thanks and regards
    Mangesh A. Bhende

  • Eap-fast and CWWLSE-1030

    HI,
    I configure a Wireless Lan with 3 AP1131G-E-k9 and a radius serveur CWWLSE and Eap-Fast AND WPA2
    All seem's to be OK but some Laptop are obliged to re-authenticate several time a day ?
    Anybody has a idee if thre is a timer or
    others paramatter I should do set ?
    Thanks for your Help

    I recently ran into this issue. What I found although not that technical....if the user is prompted for the PAC and does not accept, I had a hard time getting them to authenticate afterwards. I was able to remove the user from the AAA server and once I added them back in they were able to authenticate with no issues. Again this is a very basic finding  and I have not had time to test my theory. I believe it has someting to do with the way AAA caches the user account, perhaps there is a denial of service or time-wait before the next login attempt is permitted. If you are using AD and not local accounts use the option, on the Radius server to Remove Dynamic Users.
    hardware userd Version 7.0...5508 WLC, 3500i AP's, WCS, MSE, Cisco ACS/Radius 4.2 WPA2, 802.1x, EAP-FAST

Maybe you are looking for