Cyan Will Not Print

Cyan will not print; print head is rated as "Good" by HP; also receiving Failure Notice: "Alignment Failed."HP's "Ink Cartridge Status" does not register any "Ink cartridge level," although there is plenty of Cyan ink in the cartridge. Changing Cyan Ink cartridge did not help.

@Bluemoon1, welcome to the community
I understand you mentioned that you have tried troubleshooting steps for the issue you're having with the cyan ink not printing from your Officejet L7780, however, I am going to post my suggestions as I am not sure what steps you've tried. Please look over the steps and give them a try to hopefully bring the cyan back to print again!
Fixing Print Quality Problems for the HP Officejet Pro L7500, L7600, and L7700 All-in-One Printer Se...
A 'Cartridge Problem,' 'Ink Cartridge Failure,' or 'Incompatible Ink Cartridges' Error Message Displ...
If the issue does continue after the steps are done, please give us a call to see what your printer options are at that point. HP may have out of warranty options for the printer, if the printer is no longer in warranty.
Please call our technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region. http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html
Have a great weekend
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

Similar Messages

HP Officejet Pro 8500 Cyan ink will not print. installed a new one, but no success

HP Officejet Pro 8500 Cyan ink will not print. installed a new one, but no success

I had to replace both printheads about $85 a piece. It may be more cost effective to buy a new printer. Once I replaced the one printhead, the other one went out. It is common and it did solve the issue. I really like my printer and if it gets me another year or so, I think it was worth it.

L7555 Will not print cyan

My grandparents have an old 7555 Pro and recently installed new cartridges in it but since then they have not been able to print anything with cyan in it. They asked me to fix it and after a few diagnostic reports, two alignments (it was way off), four auto cleanings and a hand cleaning the thing still will not print cyan. They did tell me that it had started this a few months ago but it was just faded, not full on missing the cyan. The diagnostic says the printheads are fine and the ink is brand new but they do not have the money to get it fixed somewhere since it is obviously out of warranty. K, Y and M all work fine it is just C that is having issues. The printer is not desplaying any error messages and comes out with a perfect self-test.
I have a suspicion it is the ink line but I am weary about pulling it apart only to find out it's a glitch or something. I've looked around the forums before signing up and none of the answers for this issue worked. So before I go pulling this monster apart does any one have any suggestions to try to get the cyan to work?

Hello UnknownGhost,
Welcome to the HP Forums.
I see that you are having some printing issues with the cyan ink cartridge.
I do have a couple steps we can try in the attempt to troubleshoot this issue.
First off, please make sure that you have the printer power cable connected directly to a wall outlet and not a power bar/strip. Here is a document that uses a LaserJet printer as an example but it is meant for HP products in general. Please click on the following link that explains the Issues when Connected to an Uninterruptible Power Supply/Power Strip/Surge Protector.
I have also located a document that will give troubleshooting steps on Fixing Print Quality Problems for the HP Officejet Pro L7500, L7600, and L7700 All-in-One Printer S....
Please feel free to write me back if you have any other questions or concerns.
Cheers,
Click the “Kudos Thumbs Up" at the bottom of this post to say “Thanks” for helping!
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
W a t e r b o y 71
I work on behalf of HP

My HP Officejet 6500 E709a All-in-One will not print more than one copy at a time.

My HP Officejet 6500 E709a All-in-One will not print more than one copy at a time. This is especially disconcerting at Christmas time when you're trying to get Christmas letters in the mail! Any help?

The cyan portion of the printhead may be clogged. I would suggest running the diagnostics shown here. If three levels of cleaning of the printheads does not resolve the issue you may need a new printhead.
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

HP Officejet Pro 8500 Wireless - will not print green

I have a HP Officejet Pro 8500 Wireless that will not print Green.
I have:
1. Cleaned Printhead using device cleaning command. All steps
2. Alligned Printer - get message 'Alignment failed. Refer to device documentation for details.' I see know documentation
3. Calibrate Linefeed
4. Unplugged device while it was on and then replugged restarted.
5. Unplugged device while it was on and cleaned magenta/cyan printhead (following instructions from your website explictly).
The Alignment failed message persists and it still will not print green. I have done some of the above multiple times.
I hope you can help quickly. I have a home office and this is putting me behind a lot!
If I need a new printhead, get one and it does not fix the problem, can I return it? How can I get a printhead quickly?
THanks! Kathy

Hi KathyGates,
Please let me take a moment to say "Welcome" to the HP Forums. I hope you enjoy your experience!
To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I see that you are having an issue when it comes to printing in green. I also see that you are having some issues with aligning the printer.
I have a few suggestions and with any luck, hopefully get this issue resolved for you.
Please start off by making sure you have the printer power cable connected directly to a wall outlet and not a power bar/strip. I have a document that uses a LaserJet printer as an example but is meant for HP products in general. Please click the following link that explains the Issues when Connected to an Uninterruptible Power Supply/Power Strip/Surge Protector.
I also have a document that troubleshoots Fixing Ink Streaks, Faded Prints, and Other Common Print Quality Problems.
Please write me back if you are still having issues or if you have more questions.
If I don't hear back from you today, I hope you have a Fantastic Thursday.
Cheers,
Click the “Kudos Thumbs Up" at the bottom of this post to say “Thanks” for helping!
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
W a t e r b o y 71
I work on behalf of HP

HP color laserjet CP2025 will not print. Help.

I have a HP color laserjet CP2025, but it will not print. I installed the driver HP Color LaserJet CP2020 Series PCL 6. I have a Windows Vista Home Premium. There is a message to replace the cyan cartridge, but I assume if the printer has black ink, then it'll print in black and white. Do I need to replace the cyan cartiridge for it to print? What other options can I try to troubleshoot?
Thank you.

@kesler
‎Thank you for using HP Support Forum. I have brought your issue to the appropriate team within HP. They will likely request information from you in order to look up your case details or product serial number. Please look for a private message from an identified HP contact. Additionally, keep in mind not to publicly post ( serial numbers and case details).
If you are unfamiliar with the Forum's private messaging please click here to learn more.
Thank you,
Omar
I Work for HP

HP Officejet Pro L7780 All-in-One Will Not Print Blue Ink - It Prints Pink Instead

HP Officejet Pro L7780 All-in-One -
Issue:
Blue ink will not print (It prints the color pink instead.).
Actions taken:
1. Cleaned ink heads.
2. Replaced ink cartrige.
3. Reinstalled software.
Sugestions by HP customer service:
Purchase a new printer: Because the issue is software related - not reading the blue ink cartrige.
Any suggestions or advice would be very much appreciated.
Thank you for your time!
Thank you.
Sincerely,
Ryan

The cyan portion of the printhead may be clogged. I would suggest running the diagnostics shown here. If three levels of cleaning of the printheads does not resolve the issue you may need a new printhead.
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

LaserJet 4600 will not print black

My LaserJet 4600 has only 12-13,000 pages on it and will not print black ink. Magenta, cyan, and yellow print fine. The black cartridge works in my other 4600, and I've also tried the magenta in the black slot-- it will not print in that slot either...... Appears to me to be a hardware issue..... Any suggestions as to what the problem is, and is it something that I can fix? Or is it a job for a repair shop?........... Another aspect is-- is it cost prohibitive to fix?.. Thanks......................

Good day,
To get your issue more exposure, I would suggest posting it in the commercial forums since your product is a commercial product. You can do this at Commercial Forums.
Enjoy your day!
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

Hp photosmart 5515 will not print black.

hp photosmart 5515 will not print black, but will print colors (cyan blue yellow). Printer shows full inks on all colors.
This question was solved.
View Solution.

No solution. Power cycled several times, power cycled computers, modem, router, performed all recommended cleanings, changed all ink cartridges, checked it over several days - no go. Then, suddenly, after weeks, it started printing again. That's one hell of a gremlin. Throughout all of this time, my inexpensive Canon printer never faltered.

Cyan ink not printing

I have an HP officejt pro 8500. Out of nowhere in the middle of printing my cyan ink will not print i replaced the cartridge witha new one i did a the diagnostic test and it still will not print. all colors show except for cyan. I cleaned printheads could the cyan line be clogged

Hello,
Please click here to access the steps that should resolve the issue.
Regards,
Jabzi
Give Kudos to say "thanks" by clicking on the "thumps Up icon" .
Click "Accept as Solution" if it solved your problem, so others can find it.
Although I am an HP employee, I am speaking for myself and not for HP.

HP Laserjet 4100 on network will not print

Since I’ve installed Snow Leopard, I have not been able to print with my HP Laserjet 4100.
My set-up: new 24” iMac, many hard drives and more. Two devices: HP Color Laserjet 5550 and HP Officejet J5750 are connected to the iMac through a USB Hub. Although initially scanning did not work with the J5750, I was able to make that work once additional drivers were downloaded from HP. Both work fine.
I also have an older HP Laserjet 4100 which has been my steady workhorse for years. It only has Ethernet and serial port outlets. It is connected to an AT&T 2-Wired Ethernet Hub/DSL Modem (model 2701HG-B) that is connected to the iMac.
I’ve contacted HP and Apple about this problem. None of the three people I worked with at Apple could help and the HP representative was unsure if they could help but that it would cost me $40 to find out. According to HP website, since Apple Talk no longer exists, we are required to input the IP for the device. For the 4100, the IP address is 10.0.1.100. I tried this two ways: in the “Add Printer” window under “IP,” inputted as the IPP, and inputted as the HP Jetdirect Socket (as per the HP instructions). When this is done, the printer shows up when you give a print command. However, it does not show up in the “Add Printer” window under “default” or anywhere else.
Status: If I connect the 4100 Ethernet cable directly to the back of the iMac, the “Supply” level indicates the true level of toner in the 4100. However, it will not print. If I connect the 4100 Ethernet cable to the Ethernet hub, the supply level does not show nor can I print.
Any suggestions?

I am struggling with the same problem. I have two HP 4100dtn printers on ethernet. Each has a manually assigned IP address. I can set up the printer(s) just fine in the Print & Fax Preference and Snow Leopard finds the printer just fine when I enter the IP address and chooses the correct HP Driver.
When I try to print, my print job appears in the queue as expected, than an error appears that something about a "bad command". Sorry, I'm home right now and don't have direct access to the printer so I can't give you the precise language of the message, but the gist of the message is that the system tried to connect to the printer to send the print data but the printer does not know how to respond to the command that was sent.
It's as if the firmware in the 4100 just doesn't have something in it's lexicon that Snow Leopard needs. The HP web site is no help. One page I found says the printer is supported (http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?lang=en&cc=us&obje ctID=c01664444&jumpid=regR1002USEN ) and another page I found says that it is not supported (http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?lang=en&cc=us&obje ctID=c01879014&jumpid=regR1002USEN). The HP on line chat won't let me log in and hold a chat with HP unless I know the Serial Number of the printer, which I don't have here at home.
More to follow tomorrow.
Anyone have any ideas?

HP Laserjet 4100 will not print in Snow Leopard

Since I’ve installed Snow Leopard, I have not been able to print with my HP Laserjet 4100.
My set-up: new 24” iMac, many hard drives and more. Two devices: HP Color Laserjet 5550 and HP Officejet J5750 are connected to the iMac through a USB Hub. Although initially scanning did not work with the J5750, I was able to make that work once additional drivers were downloaded from HP. Both work fine.
I also have an older HP Laserjet 4100 which has been my steady workhorse for years. It only has Ethernet and serial port outlets. It is connected to an AT&T 2-Wired Ethernet Hub/DSL Modem (model 2701HG-B) that is connected to the iMac.
I’ve contacted HP and Apple about this problem. None of the three people I worked with at Apple could help and the HP representative was unsure if they could help but that it would cost me $40 to find out. According to HP website, since Apple Talk no longer exists, we are required to input the IP for the device. For the 4100, the IP address is 10.0.1.100. I tried this two ways: in the “Add Printer” window under “IP,” inputted as the IPP, and inputted as the HP Jetdirect Socket (as per the HP instructions). When this is done, the printer shows up when you give a print command. However, it does not show up in the “Add Printer” window under “default” or anywhere else.
Status: If I connect the 4100 Ethernet cable directly to the back of the iMac, the “Supply” level indicates the true level of toner in the 4100. However, it will not print. If I connect the 4100 Ethernet cable to the Ethernet hub, the supply level does not show nor can I print.
Any suggestions?
Chuck Stewart
< Edited by Host >

Well, another week has gone by without a solution.
Again, here is the problem:
I have a 24" iMac connected to a USB hub and an AT&T 2-Wire DSL/ethernet hub. When I upgraded to Snow Leopard 10.6.1 and now the update 10.6.2, the two printers on the USB hub work fine but the HP Laserjet 4100dtn does not print. This old printer has only ethernet or serial ports. I've downloaded and installed the HP driver updates from Apple and HP to no avail. According to HP, I must add the 4100 manually using its IP. I've followed the instructions while adding a printer to select IP- HP Jetdirect - Socket. The address of the printer is 10.0.1.100. When I type this in, the window says that this is a valid and complete address. It searches and then says the "Print Using:" is a Generic PostScript Printer. The driver for this printer, I believe, should be "HP LaserJet 4100 Series v.3010.107" Regardless, when I click Add the window "Determining Installable Options" shows "Status: Connecting to printer..." It never establishes a connection.
The 2-Wire DSL/Ethernet Hub/Modem, has an IP of 192.1687.1.66, Submask 255.255.255.0 and Router (DNS) 192.168.1.254.
If I plug the ethernet cable directly from the printer to the iMac, the supply level shows correctly but will not print. If I plug the ethernet cable from the printer to the 2-Wire and then to the iMac, it neither shows supply level nor prints.
Any suggestion as to how to fix this problem? (I've been on the phone with 3 different Apple respresentatives and 1 HP representative with no success.)

Officejet Pro 8600 - Macbook Pro and Macbook Air will not print

Products:
HP Officejet Pro 8600
Macbook Pro (Mac OS X, Version 10.7.5)
Macbook Air (OS X, Version 10.8.2)
Question:
Why did my Macs initially print fine, but now will not print at all?
Full Story:
I have a wireless network at my house that consisted of a 30mb cable internet, Netgear 900n, HP Officejet Pro 8600, 2 Dell Laptops with Windows 7, a Lenovo Laptop with Windows 7, and Dell Tower with Windows 7 - All printed just fine.
The HP Officejet 8600 was added to my network about 2 months ago.
I added a Macbook Pro and a Macbook Air about 3 weeks ago. Both Macs printed just fine for about a week. Then suddenly they stopped. I spent about 2 hours on the phone with HP Service, and they finally said it must be my router. So I called Netgear. Netgear was useless! They wanted me to agree to charges for services before they would even discuss the issue.
Due to information provided by HP's service support, and because Netgear will not support their product, I promptly purchased a new router - an Apple Airport Extreme.
The Macs recognize the printer, will print if hardwired via a USB cable, but will not print wirelessly to the Officejet Pro 8600. The PCs print fine.
The frustration that is being felt is compound by the fact that the Macs printed just fine with the Officejet Pro 8600 2 weeks ago, and now the printer just shows "idle"... even with a new router. (see image below)
Please help, I appreciate any support.
As a side note, the HP Service rep was very friendly, and definitely tried to support the HP Product, which is much more than I can say about Netgear.
Thank you,
This question was solved.
View Solution.

Hi,
More likely the issue related with Multicast, which Apple devices relies on to communicate with teh device through the network.
First try unplugging the router for 30 seconds.
Plug it back to the power and wait for 2-3 minutes.
Turn the HP printer Off and back On, then check for any difference.
If the same persists, try changing your router configuration as following
Note: the settings below are not related with the HP product, I provide you the steps as a best effor and those are only based on my own knowledge. you may try modifying the router settings at your own risk:
Open the router configuration page (can be found listed as the Default Gateway by clicking the Wireless icon on the printer, then print a network configuration report.
Click the Advanced tab.
Click the Setup option from the menu, then click on WAN Setup.
Make sure to uncheck the box next to Disable IGMP Proxying and Apply the changes.
Click the LAN Setup on the same Setup menu.
Set the RIP Version as RIP-2 and Apply the changes.
Reboot your router and then check for any change.
I hope you may find that information useful, you may also use the user guide below for further information:
http://www.downloads.netgear.com/files/GDC/WNDR4500/WNDR4500_UM_07DEC2011.pdf
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

HT201465 I have installed software for a HP Deskjet 1510 printer but it will not print

I have OS X Yosemite 10.10.3 and I just purchased a HP Deskjet 1510 all-in-one printer. I have installed the software and my computer is picking up the printer but it will not print. I have restarted the computer and it still will not print.

Hello jamesettafromfl,
If you continue to have issues setting up your new printer in Yosemite, you may find the information and troubleshooting steps outlined in the following articles helpful:
OS X Yosemite: Add or remove a printer
OS X Yosemite: Printing troubleshooting
Sincerely,
- Brenden

My deskjet 3050 says it is connected to the wireless network but will not print unless wirelessly

my deskjet 3050 all in one j610 printer will not print wirelessly even tho it says it is connected to the network.
It will only print when connected by usb cable.

Download and run this utility:http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?cc=us&lc=en&jumpid=ex_r4155/hho/ipg/ccdoc/p...
What does it say?
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

Cyan Will Not Print

Similar Messages

Maybe you are looking for