Cycle Count with new battery?

I recently got Apple to ship me a new battery and I shipped my old one back. With the replaced battery, I am still having the cycle count issues. It says the cycle count is '2'.
Now I replaced my battery last time because of a low cycle count. Why is the "new" battery doing this again??

You are misunderstanding the cycle count phenomenon.
That's the number of cycles it has gone through, not the number of cycles left, assuming you are using a software that registers the count correctly.
Here's one which is Universal:
http://www.coconut-flavour.com/coconutbattery/index.html

Similar Messages

  • Macbook 13.3 with new battery and new magsafe adaptor will not charge above 80% no indicator light on charger display states "not charging" while attached to charger

    macbook 13.3 with new battery and new magsafe adaptor will not charge above 80% no indicator light on charger, display states "not charging" while attached to charger

    rgregoryadams wrote:
    macbook 13.3 with new battery and new magsafe adaptor will not charge above 80% no indicator light on charger, display states "not charging" while attached to charger
    You'll want to reset your SMC (System Management Controller). Instructions are simple:
    http://support.apple.com/kb/ht3964

  • Macbook shutting down with new battery with 15 minutes remaining (consistent)

    Just installed a supposed new battery for the White Macbook 4,1 model, from an Amazon seller.  The battery looks authentic, fits well, accepts and fully charges, but it is a little more yellow in color than the rest of the casing.  That's all I can find wrong with it.
    The problem I am having is that the macbook will shutdown consistently with ~15 minutes left on the charge (under 10%).  I get no low battery warning.  I have tried numerous SMC and PRAM resets with no luck.  Battery temperature and computer temperature appear to be fine so the unit is not overheating.  The only indication I can assume is suspicious is that the battery will draw over 2 amps at times as that magic time remaining approaches.  Battery cycle count is 3 and remaining capacity is over 5300 mAh.
    Here is the pertinent info from System Profiler:
    Battery Information:
      Model Information:
      Manufacturer:          DP
      Device Name:          ASMB0?6
      Pack Lot Code:          2
      PCB Lot Code:          0
      Firmware Version:          110
      Hardware Revision:          500
      Cell Revision:          102
      Charge Information:
      Charge Remaining (mAh):          631
      Fully Charged:          No
      Charging:          No
      Full Charge Capacity (mAh):          5336
      Health Information:
      Cycle Count:          3
      Condition:          Normal
      Battery Installed:          Yes
      Amperage (mA):          -836
      Voltage (mV):          10900
    I'm running Lion 10.7.2 with 4 gigs of RAM installed.  I've read the Firmware version of this battery (110) needs updating but I can't find an updater that will run in Lion.  I also don't understand what ASMB0?6 means in the device name (what's up with the ?).  Again, the battery appears to be a legit Apple product and brand new by the cycle count (3).
    Can someone help me resolve this issue?

    HI kostby,
    I've been trying to calibrate the battery but can't do the 5-hour sleep procedure since the computer doesn't go to sleep.  Although I have noticed that the last time the shutdown occurred, the battery indicator light was one and blinking.  So the battery thinks it is drained but the computer does not (hence 15 minutes remaining and no low battery warning).  So I took the battery out of the computer last night with blinking indicator light and left it alone overnight.  I reinstalled the battery this morning and am charging it now.  Hopefully it calibrated.
    If not, I am going to ask for a replacement from the Amazon.com seller, since I just bought it "new".
    Thanks for your insights.

  • Satellite P300-161 - troubles with new battery

    I have just purchased a new battery on line for the above laptop.
    When I place the battery in the laptop, the orange charging light comes on, and the battery appears to charge.
    However, after several minutes, the charge light starts to flash, and stays flashing. I therefore cannot tell if and when the battery is fully charged.
    When I take the mains charger out and turn on the laptop, it comes on ok, but the battery icon is showing 'remaining time unknown' and is grey. The charge light is still flashing orange.
    When I emailed the company the reply was:
    <Hope the battery works well with your laptop.
    As a new battery, for the first three times, you should full charge 12hrs. Then discharge, 3% remains then recharge.
    Remember for the first three time charge, you should shut down your laptop>
    When I charged for 12 hours, the laptop would not turn on.
    The next response was:
    <Could you please try to plug and unplug the battery for more times,then recharge.
    If the battery still can't work? Would you pls kindly take photos of the battery which was sent by us and your original one to us?
    Just to see barcode(the white label)\part number\fit modle. >
    Has anyone any thoughts? My impression was that the battery is faulty.

    Thanks for reply.
    The battery in question is a high capacity 7800 mAh. Could this have a bearing on the problem!
    I'm not sure if Toshiba do one as large as this.

  • How setup cycle counts with wms picking

    How setup cycle counts to dispatch tasks when make picking of an order with wms and activate an exception?

    Hi,
    We need to use customization with respect to your requirement as you cannot meet the whole requirement with seeded parameters available in Picking rules. Let me know your mail id so that i can farward you an document that is from oracle which suggests about the using the functions and packages in the picking rules.
    Regards,
    Sravan.

  • Z10 will not charge & with new Battery will not turn on

    I have have had my Z10 about a month now, I am gernerally happy with it as a work phone which is similar to my private Iphone5. Unfortunately the Battry life has been reducing on a weekly basis to around 4 hrs between charges. Now it is dead and will not wake up, so I bought a new Battery, now it blinks once the three times but will not turn on.
    Any ideas ? The OS is the latest on the Blackberry site, but as I can turn the phone on I can't be more specific.

    Hello,
    From your description, if your charger is "known good" (e.g., it can charge other devices), then one can only deduce that something (hardware) inside the BB related to passing power from the charger to the battery has broken. Or that something passing power from the battery to the device has broken.
    Regardless, if your charger is 100% fine, then it sounds like a hardware problem for which no amount of OS/software level fixes nor internet-distance diagnostics can be of much value.
    I recommend you seek formal support via your official warranty channel. Normally, that starts with your original place of purchase or an authorized service center -- it varies by region.
    Good luck!
    Occam's Razor nearly always applies when troubleshooting technology issues!
    If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
    Join our BBM Channels
    BSCF General Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

  • Inbound Idoc function module  for Cycle count with msg type WVINVE

    Can any one tell me which is the standard function Module which processes Cycle count for message type WVINVE.
    My requirement is to setup Inbound Idoc for cycle processing with message type WVINVE.

    Hi Mukesh,
             Inbound FM is IDOC_INPUT_STORE_INVENTORY , and Process code is WVIN.
             Yoou can check this in Tcode WE42 for process code WVIN.
    Regards
    Srikanth M

  • Satellite A100-225 is not charging even with new battery

    Hi, Having a charging problem. Laptop suddenly shut down whilst using. Tried to start up but power light goes out and it shuts down again. With battery connected and ac adapter switched on the blue power light and yellow battery light stay on a few seconds and then shuts down, not allowing start up.
    Took the old battery out thinking it was that and my laptop starts up fine using just the ac adapter as this is how I am currently posting this. Refit the battery and the power light comes on and off again every few seconds and prevents start up.
    Have purchased a new battery thinking it was faulty but to no avail, exactly the same problem.
    Left the laptop off to charge the new battery but noticed the blue power light and yellow battery light going on and off together every few seconds.
    If I try to start the laptop up while the power light is on it starts to start but as soon as the power light goes out it stops. My thoughts are the charging unit inside my laptop is shorting out but I am no expert.
    Does anyone have any idea what the problem is and would it be expensive to fix as I have just spent 48 on a e new battery.
    Thanks Mick

    >Refit the battery and the power light comes on and off again every few seconds and prevents start up.
    Are you sure that the battery is compatible ? did you purchase the genuine battery from Toshiba ASP?
    I think batteries from 3rd party retailer could not be compatible always so I would test the notebook with a battery recommended by Toshiba.
    At the other hand it could be a motherboard problem but if the notebook start up properly using the AC adaptor, I would not be quite sure if its really a mobo issue.
    Try also this:
    Remove battery and AC adaptor, press power button 30sec long.
    Then insert the battery and connect AC adaptor and check if you could power up the unit.

  • PowerBook shuts down even with new battery

    My mom has a 12" PowerBook that she recently purchased a new battery for. Even with this new battery, the laptop shuts down seemingly randomly before the battery gets even down to 20%. They sent a new battery, and the laptop still does it.
    Any ideas?

    Sounds like the power manager needs replacing. See these sources which may be able to fix it for less than Apple:
    http://www.dttservice.com/
    http://www.powerbookresq.com/
    http://www.microdocusa.com/
    http://www.macspecialist.com/
    http://www.techrestore.com/
    Or find one at a parts store, and fix it yourself:
    http://www.ifixit.com/

  • Freezes on startup screen with new Battery

    laptop works fine with old Battery just battery will no longer hold a charge installed a new Battery freezes on startup screen ran battery test ok got a 2nd new Battery using the numbers off the old one same thing followed hp noteboook pcs testing and calibrating the battery everytime the first part says battery ok the 2nd part says na. reinstall old battery laptop works fine

    Thank you for visiting the HP Support Forums and Welcome. I have read about your Compaq-Presario and having an issue with the New battery. Here is a link to test and calibrate the battery.
    Plug the power adapter directly into a functioning wall outlet. Do not plug it into a power strip, surge protector, or secondary power source as this could cause and issue.
    If that does not help try the Microsoft ACPI-Compliant Control Method Battery is basically the driver that communicates between the computer and the battery. There is a chance that it is corrupted. It is reading the battery level wrong, so the computer thinks the battery level is higher then what is actually is, so when it runs out of juice it shuts down.
    Step 1. Go to Device Manager
    Step 2. Select Batteries
    Step 3. Right click the "Microsoft ACPI-Compliant Control Method Battery" that is listed there
    Step 4. Click Uninstall
    Step 5. At the prompt put a check in the box to remove the current driver
    Step 6. Shutdown the computer
    Step 7: Remove the battery for minute and then put it back in
    When the computer comes back up it should automatically find the driver.
    Step 8. Go to Device Manager
    Step 9. Select Batteries
    Step 10. Right click the "Microsoft ACPI-Compliant Control Method Battery" that is listed there
    Step 11. Click "Search automatically for updated driver software"
    Do the same thing with Microsoft ACPI-Compliant Embedded Controller.
    Hope this helps.
    Thanks.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the bottom to say “Thanks” for helping!

  • X201 random shutdown with new battery

    Hi all, 
    I use my X201 for 4 years now without any trouble. The original battery getting worned out, I replaced it with a 9Cell Duracell (Sanyo) one.
    Since then and only when I use the new battery, AC unplugged, my laptop randomly shuts down with no warning. No overheating issue.
    The Win7 logs point to powerfailure (Kernel Power at restart shows error 61)
    Any clue about i)the reason for this bizarre behaviour ii)the cure
    I would gladly purchase a new Lenovo battery if only I were sure to solve the problem ...
    regards and thanks !
    Christophe 
    Solved!
    Go to Solution.

    Hi, clahaye
    nice to see your success!
    Refering to the solution you've found the lock slider should be only mechanical device. Is there a chance one of the battery electrical contact wasn't reliable while the slider was open? I left the slider opened on my x220 many times w/o issues.
    x220 | i5-2520m | Intel ssd 320 series | Gobi 2000 3G GPS | WiFi
    x220 | i5-2520m | hdd 320 | Intel msata ssd 310 series | 3G GPS | WiFi
    Do it well, worse becomes itself
    Русскоязычное Сообщество   English Community   Deutsche Community   Comunidad en Español

  • Menu bar 0% with new battery

    I'm going to repost this with some new information. ibook G4 - formerly using newertech battery, whose health was good. - purchased a NEW apple replacement which showed 2/3 charge on the battery lights- no help. The menu bar reads 0% after a PMU reset - then when the battery is left in, it eventually has the "X" across the battery icon showing no battery installed - the ibook runs fine with the power adapter plugged in. PMU resets still no help. Left the computer plugged in overnight and the new apple battery which was 2/3 charge is now 100% (by battery lights) which indicates to me it is charging. How can I get the computer to recognize the battery?
    thanks for any help....

    Did you restart the computer with the battery installed and the computer plugged in?

  • PowerBook enters sleep mode with charger on and with new battery in Full

    Hi all,
    My powerbook enters in Sleep mode when it has a lot of energy. I have the powerbook with the charge on and battery in full charge and it still goes to sleep mode. It happens even when I'am working a lot with the computer. It appears that when a left my computer go to sleep over night the next day e goes a lot to sleep even when I'am working with the computer. I have tried to use just the charger, and just de battery but the error continues. I havemy power setting and it is e best performance (and it never goes to sleep in this mode).
    I can only avoid this if I never put the computer to sleep, because I i put it i will start putting it self to sleep.
    I have bought a new battery (7 months) and a new charger (2 month) recently, could be this the case?
    What is happening to my computer?
    It is my computer to ald and tired and needs to sleep a lot :/ ?
    Thanks for any help!

    The date only goes to 1970-01-01 if e click in power on without the battery and the AC adapter.
    If I remove the battery and unplug the AC adapter e wait many minutes and put back on the battery and the AC adapter a switch the power back on the date staid the same.
    I have notice one other think, some times the new battery that a bought in apple store does not charge (a have to remove the AC adapter a plug back in for it to charge), the AC adapter is correctly plug-in but it does not charge. I am begging to suspect that it is something wrong the the hardware (or the battery or the charger) sell by apple store.
    Is the any place for replace bad hardware still in warranty in apple store?
    What is the place to contact apple suport for this matters?
    Thanks!

  • Help with new battery issues

    I just bought new battery for my Macbook aluminium 13inch (late 2008),and i would really appreciate if you guys could help me with my issue. When i put my new battery in Mac how long do i have to charge it (all day or should i threat it like its not new and when its charged i can remove it from the charger)?
    I really want to do everything right.
    Thnx in advance.

    No I haven't and HP seems not to care about the problem so guess what. No more HP's for me anymore....

  • TouchSmart tx2-1370us HUGE issues with new battery PLEASE HELP I AM DESPERATE!!!!!

    I purchased a new battery for my laptop. I got a LHP-41XT which is supposed to last longer... the following issues I initially thought were because I got a defective battery but I replaced it for another one and they are still happening:
    Battery is fully charged. When power cord is disconnected after a random amount of time the computer just dies while the charge does not even get down to 80%. The computer does not even go into the shut down process, it just completely dies.
    When trying to turn on the computer with battery it starts to boot up and after a few seconds it completely shuts off. After that no matter how many times I press the bottom to turn it on it just wont even try to turn on. I have to turn it on with the cord. 
    To try to remediate the problem I have tried and failed the following:
     -  Get a new battery of the same model in case the problem was the battery
     -  Calibrate the battery using every single option there is (changing power profile to "Calibrate," letting the computer discharge completly without using it, letting the computer discharge completly using it, letting the computer discharge completly without using it in while in safe mode) but the computer just keeps on dying.
     -  Change all the power settings so the computer does not hibernate, go into shut down, or does anything when the power levels go down.
     -  Erase completely the battery drives so the computer does not try to detect the battery charge.
     -  Upgraded the computer bios to the latest version
     -  Replaced BIOS battery
    Please someone help me I do not know what else to do and I don't want to keep wasting money to try stuff that does not work...

    No I haven't and HP seems not to care about the problem so guess what. No more HP's for me anymore....

Maybe you are looking for