D-Link DIR-615/Macbook detecting but not connecting

This is my first post on the forum.
So I went on a vacation back in January for about a week, but during that week I unplugged my D-Link DIR-615 Wireless N router and modem (Toshiba, Time Warner), just so I wouldn't have people attempting to connect to it for any reason by any means. Fair enuf, right?
I get home, connect the mac, modem, router. Airport will detect the network, but will not "transmit" the internet, won't pull up any webpages.
Any ideas? I've checked the through some of the other posts, but it's kind of hit and miss.

This is because your Mac is connecting to your router but is failing to obtain an IP address via DHCP.
Is your Mac still set up to obtain an address automatically via DHCP?
If so, try the following sequence:
1) Disconnect from your D-Link
2) Power off the cable modem and router.
3) Power on the cable modem and wait until its status lights indiciate it is connected to its network.
4) Power on the D-Link and wait until its status lights state it is connected.
5) Try to reconnect to the D-Link on your Mac.

Similar Messages

Help! My Zen Micro is detected but not connected to zen media explorer & mediasou

Hi
recently i just bought a creative zen micro at 5 GB. after installing all the drivers and programs using the installation CD that came with my player, I connected my player through the USB cable to my pc USB root hub.
an auto-detect of my zen micro window pops up at the righthand corner, prompting me to click 'organize' in the creative media source. clicking the organize option, mediasource program starts but while it is loading the music library, an error message: CTCMS, The program has performed a illegal operation......etc.
i tried disconnecting my player followed by opening the media source prog and connecting my player after that. another error message: file operation failed. please ensure that your player is properly connected.
I'm using windows 98 SE on an AMD processor. i was able to use the removable disk mode of my player to store data from pc. However when comes to the media mode of my player, it is shown as not connected status in the zen micro media explorer and in the creative media source program, it's either shown as not properly connected or illegal operation when loading music library from my player. in addition, under the device manager, the creative zen micro driver is shown as working properly. i was also able to upgrade my firm ware to version .02.05. using my pc to connect to my player. However, even before upgrading the firmware, this problem is already present. i have contacted the creative technical support helpdesk for advise on this issue and they have suggested to me various solutions such as checking my drivers if they are updated, reinstalling the drivers and software applications for the media library, installing jet engine service pack for my windows and the MDAC component but still nothing works.
anyone have any suggestions? pls help
thanks
Message Edited by fanaticpat on <SPAN class=date_text>05-30-2005 <SPAN class=time_text>0:20 PM
Message Edited by fanaticpat on 05-30-2005 0:2 PM

Hi,
Sorry I can't help you. I just wanted to let you know I have the same exact problem. It started three days ago and I've been going back and forth with creative support and nothing has worked. I am beginning to grow really distressed. I feel a little better now because after seeing that it's happening with someone else, it is most likely not the player. I am running windows 98 SE as well. I also have an AMD Duron processor. I have a new computer on the way with windows XP I really hope it works. But now I have a new problem. I listed it on the front page of this forum a few minutes ago. My player froze and now only boots up in rescue mode. I am getting so frustrated with my player. If you figure anything out will you be as kind as to send me a message on how you got your player working again? I would really appreciate it. Thanks.
Nick
Message Edited by nichols088 on <SPAN class=date_text>06-09-2005 <SPAN class=time_text>05:33 PM
Message Edited by nichols088 on 06-09-2005 05:35 PM

3G Pen detected but not connecting

Hello Everyone,
Today I recieved a 3G Usb PEN and tried to install it and make it work on Arch Linux (It's a Huawei E173s), the pen was detected but there was no connection. I've tried a lot of configuration, but since I don't really know if the apn was right, I tried to connect and old 3G Pen (a Huawei E220).
And then tried to connect. Network Manager (here in Gnome3), show me that it was trying to connect but then fail.. And I really don't know why :S...
This is the log from /var/log/daemon.log :
Feb 15 12:31:06 localhost NetworkManager[2022]: <info> Activation (ttyUSB0) starting connection 'Clix Omissão'
Feb 15 12:31:06 localhost NetworkManager[2022]: <info> (ttyUSB0): device state change: disconnected -> prepare (reason 'none') [30 40 0]
Feb 15 12:31:06 localhost NetworkManager[2022]: <info> Activation (ttyUSB0) Stage 1 of 5 (Device Prepare) scheduled...
Feb 15 12:31:06 localhost NetworkManager[2022]: <info> Activation (ttyUSB0) Stage 1 of 5 (Device Prepare) started...
Feb 15 12:31:06 localhost NetworkManager[2022]: <info> Activation (ttyUSB0) Stage 1 of 5 (Device Prepare) complete.
Feb 15 12:31:17 localhost NetworkManager[2022]: <warn> GSM connection failed: (32) Sending command failed: 'Resource temporarily unavailable'
Feb 15 12:31:17 localhost NetworkManager[2022]: <info> (ttyUSB0): device state change: prepare -> failed (reason 'unknown') [40 120 1]
Feb 15 12:31:17 localhost NetworkManager[2022]: <info> Marking connection 'Clix Omissão' invalid.
Feb 15 12:31:17 localhost NetworkManager[2022]: <warn> Activation (ttyUSB0) failed.
Feb 15 12:31:17 localhost NetworkManager[2022]: <info> (ttyUSB0): device state change: failed -> disconnected (reason 'none') [120 30 0]
Feb 15 12:31:17 localhost NetworkManager[2022]: <info> (ttyUSB0): deactivating device (reason 'none') [0]
Feb 15 12:31:17 localhost NetworkManager[2022]: nm_system_iface_flush_routes: assertion `ifindex > 0' failed
Feb 15 12:31:17 localhost NetworkManager[2022]: nm_system_iface_flush_addresses: assertion `ifindex > 0' failed
Feb 15 12:31:17 localhost NetworkManager[2022]: <info> Policy set 'Wired connection 1' (eth0) as default for IPv4 routing and DNS.
Feb 15 12:31:17 localhost NetworkManager[2022]: <info> Policy set 'Wired connection 1' (eth0) as default for IPv4 routing and DNS.
How can I solve this problem ?
Thanks in advance,
Luis Da Costa

Is this anything to do with this
https://bbs.archlinux.org/viewtopic.php?id=118746

D-Link DIR-615 (Rev H1(!)) does not work with Airport Express?

Hi there,
I had my AirPlay working just fine with my Airport Express (AX) and my wireless N Router D-Link DIR-615 (Rev. B2). Now I changed my Internet provider and received a D-Link DIR-615 (Rev. H1) and I cannot find my AX anymore (I mean, it's still here, but the AirPort Utility cant find it!)
Are there known issues between those two?
(The Rev. H1/B2 is the Hardware Version of my D-Link DIR-615. The Firmware is up-to-date (8.01 I think))
The status light is a solid, beautiful green.
I already tried the following:
- restart the AX, the D-Link and my MacBook (10.7.2)
- changed from AES to TKIP (found that somewhere in the internet)
- Reseted my AX to factory settings and configured everything new. (via Ethernet)
Probably interesting:
- After resetting to factory settings and configuring everything new, the AX showed up in iTunes, but when I tried to connect with it, it kept me waiting for 1-3 Minutes and simply did not connect w/o error message. The AX disappeared after restarting iTunes.
I'm running out of solutions..
Anyone a good question/suggestion or answer for me?
greetings
squob

Only way I see out other than waiting, is to hook he Drive to a Mac, (FW preferable for speed), then get Tri-Backup...
http://www.tri-edre.com/english/tribackup.html
Which can be set to trigger Backups when Shares mount.

Setting up D-Link DIR-615 wireless N router with a macbook pro

Hello all.
I am trying to setup a D-Link DIR-615 wireless N router with my macbook pro. I got the router, opened it, put in the startup CD, and nothing works.
I went to the D-Link site and it says that the CD is not compatible with mac's, but to look on pages 10-15 in the user manual ( on the CD), which I did and found nothing related to setting up the router on my mac.
So I'm at the very beginning (putting in the initial CD) of setting this up, and wondering how to do it. Can anyone guide me through it or point me to a thread or online description of how it's done. I have very little computer background but I can pick it up decently when I have to, so please help as I will be very grateful. Thanks,
Jonathan

Unfortunately as with most routers it will be a manual affair that is quite involved. The first thing is to connect to the router over ethernet, so you should connect the cable supplied between the computer and the router and turn the router on. Go to System Preferences and open the Network panel, make sure the DCHP setting is automatic, you should have a connection if it is already on auto, there will be numbers in all the boxes when connected. In the documentation for the router you should find an IP address for the web interface along the lines of 192.168.0.1 (this seems to be the correct one for D-Link), open Safari (or another browser if you want)put this number in the address bar and press return. There will probably be a request for password at this stage, this will be in the documentation or on the bottom of the router, fill it in and you will get to the web interface. You should then be able to follow the instructions in the router documentation to set it up. It should be fairly easy through the basic setup procedure as long as you know your internet settings.

D-Link DIR-615 cannot access wirelessly with iPhone 3G

I've added another router to my home to get better range in the far corners of the house. I added a D-Link DIR-615 hard wired to my first router. I can access this new router both by cable and wirelessly with my laptop, but not wirelessly with my iPhone.
I've tried making the password all letters, (saw a post that said numbers don't work??) and even taking out the password and leaving it blank. The iPhone sees the router and identifies it by name. When I try connecting, after entering the password, it says "unable to connect to network". IO can connect to my first router with the iPhone.
Any suggestions? I'm using WEP for encription, except when I tried it with no passwords! Thanks!

A few ideas:
Often the power on sequence is the determining factor in if/how DHCP will work. Especially when it comes to consumer-grade cable modems and routers. Try different power on sequences.
Try to figure out if your cable modem is storing and enforcing the MAC address of one of your devices. Take the router out of the picture, attach your MBP, and see if it works. Then leave the modem on, unhook the MBP, and plug in a Windows laptop. If it doesn't work, then your modem wants/needs to only see one MAC address. If this is the case, look in your routers settings for "Spoof this computer's MAC Address" and you should be good to go.
One trick I've used in the past is to assign an entirely new subnet for the router to hand out. For example if it used to give out 192.168.1.x, the new subnet would be set to 10.1.1.x. This forces every system and rebuild its caches. Too many times routers, controllers, OSes, apps, and even hardware like phones keep caches to help speed things up. It's not always obvious how to reset these. But by switching subnets you force every device to rebuild the caches.
Good luck.

D-Link Dir-615 internet problems

Hi All, I am not posting this for help. I came across a problem and could not find any help on the net that would solve it. So this is to help anyone whom might have similar problems.
First, let me give you the scenario. I have SBC DSL as my ISP and the 2Wire modem/router took a dump. I looked for a modem/router combo that was 802.11 (N) compliant. There are a few but the prices were a little above what I wanted to pay. So I ended up buying a DSL modem and a D-Link DIR-615. I set the modem to "Bridge Mode" and followed the set up instructions from D-Link. After the setup some web pages were stalling and timing out. I noticed this on HTTPS pages mostly but also pages on the Apple site too. I then went to Safari and used the "Activity Window" to show me why.
Well the cure for this, which I have not been able to find anywhere on the net, was to "Disable" QoS on the DIR-615. After that...greased lightning speeds.
Hope this helps anyone that might be suffering with the same problems.
Cheers,
Glynn

This is because your Mac is connecting to your router but is failing to obtain an IP address via DHCP.
Is your Mac still set up to obtain an address automatically via DHCP?
If so, try the following sequence:
1) Disconnect from your D-Link
2) Power off the cable modem and router.
3) Power on the cable modem and wait until its status lights indiciate it is connected to its network.
4) Power on the D-Link and wait until its status lights state it is connected.
5) Try to reconnect to the D-Link on your Mac.

Flash D-Link DIR-615-D4 with DD-WRT firmware.

Hello I ve got a D-Link DIR-615-D4 off EBay (it was used with virgin media Virgin Firmware: 1.00VG) with the intention of
replacing my HH2.
Pippincp has kindly offered to guide me through the process.
He rightly pointed out that a new thread could prove useful to other users too and here it is.
Thanks Pippin.

On the bottom of the router is a label which will give you the version number of the router.
Something like this.
H/W Ver : D4 F/W Ver:1.00VG.
From that you now know you have a D4 router which is all the info you need.
Now you need either the D-Link stock firmware for it or the custom DD-WRT firmware.
This guide is for the DD-WRT firmware but stock should be similar.
I'm not putting everything in one long post as I want to guide Brinnie as much as possible rather then just post and leave him to it so it will be in stages.
Go here and enter 615 in the search bar. Click on the version you have and download the factory webflash .bin file.
Once you have it Brinnie post back. If you have any probs post back.

Airport Extreme Card wont connect to D-Link DIR-615 (wireless N router)

Hi, I got an old Mac G5 that has the airport extreme card in it and can't connect to the internet through with my D-Link DIR-615. I tried a couple options on a MAC but didn't work. I have a Laptop running Windows Vista and had no problem connecting. I'm using WPA for security and my password has 31 characters. Do you guys think That I have to change the length of my password to 26 or even less? Is there any guide that you guys may know that cuold help me on this issue?
Thanks a lot.
Masrocha

Password
40-bit hex
40-bit ASCII
128-bit hex
128-bit ASCII
LEAP
This would be telling me that your G5's AirPort is NOT "seeing" the D-Link's wireless network as encrypted with WPA, but with WEP instead. This typically can be caused by either the D-Link's current configuration is incompatible with the AirPort card or that there is something amiss with the AirPort card itself.
BTW, My D-Link has WEP, WAP-Personal and WAP-Enterprise
Ok, we will want to stick with either WEP or WPA-Personal.
We now have two choices: 1) Continue to troubleshoot additional configuration changes to the D-Link to try to get WPA to work with your G5, or 2) Switch to the lower strength encryption: WEP.
Which would you prefer to try?

IPhone Detected But Not Identified?

I hooked up my iPhone to my base that goes into my cpu and I got this message: "An iPhones was detected, but could not be identified properly. Please disconnect and reconnect the iPhone and try again." I havent had any problems like this before. Will a reinstall over this iTunes fix the problem? I am running Windows XP. I have also noticed that when I plug up my phone, the Scanner and Camera Wizard pops up recognizing the iPhone as a camera. Also when running iTunes after I got that message, my cpu will freeze for about 5 seconds and work fine a little while then freeze again for 5 seconds. But when I close iTunes, it stops freezing.

I am having the same issue iPhone detected, but not identified. Did you get a solution to the problem? Had to go to th Apple store to register my phone. iPhone connected fine with their MacBook. That doesn't help me at home though.

My macbook air will not connect to the internet due to a self assigned IP address. I have tried trawling the support forums, but either I can't understand the suggestions, or they don't work. Please explain to me in simplest terms how to fix this. Thanks!

My macbook air will not connect to the internet due to a self assigned IP address. I have tried trawling the support forums for hours, but either I can't understand the suggestions, or they don't work. Please explain to me in simplest terms how I can fix this. Many thanks!

The warranty entitles you to complimentary phone support for the first 90 days of ownership.
If you bought the product in the U.S. directly from Apple (not from a reseller), you have 14 days from the date of delivery in which to exchange or return it for a refund. In other countries, the return policy may be different. If you bought from a reseller, its return policy applies.

When i plug in my ipod nano (6th generation) a message comes up saying it's 'detected but not identified' i've spend like all day trying to solve it, uninstalled it, reinstalled it and nothing seems to work..

when i plug in my ipod nano (6th generation) a message on itunes saying the ipod is 'detected but not identified'- i've spent all day trying to fix it and nothing seems to work so i can't sync any songs..

Hello beafraser,
Here's an article to help troubleshoot when your iPod is detected but not identified.
iPod nano: Error message saying that iPod 'could not be identified properly'
http://support.apple.com/kb/ts3218
Hope that helps.
Thank you for visiting Apple Support Communities.
Nubz

Can anyone point me in the right direction for the link to download Acrobat 9 Standard? I found the link to download 9 Pro but not standard. Old computer crashed and new computer does not have a CDR/DVD rom drive.

Can anyone point me in the right direction for the link to download Acrobat 9 Standard. I found the link to download 9 Pro but not standard. Old computer crashed and new computer does not have a CDR/DVD rom drive.

Hi,
Standard or Pro would be licensed through your serial number, the download link and downloaded file would be the same for both of them.
Pro or Standard would be determined after you put in your serial number.
Download Acrobat products | 9, 8
Thank You
Arjun

My MacBook Pro will not connect to my home wifi but will connect everywhere else. My other Apple devices (I-pad, I-touch, another MacBook Pro) connect to the router without problems. It was working fine but all of a sudden stopped working.Thanks!

My MacBook Pro will not connect to my home wifi but will connect everywhere else. My other Apple devices (I-pad, I-touch, another MacBook Pro) connect to the router without problems. It was working fine but all of a sudden stopped working.Thanks!

try this.
get back into your router's settings and start deleting devices that are not connected to your router.
you can also delete the ones that are connected - they'll connect again.
on the DHCP side of it, increase the amount of users that can connect/log in to your router.
see if that sorts it out for you.
good luck.

IPod Nano 6th Gen detected but not recognized

Since recently, my IPod is not being recognized by iTunes (11.1.4.62 ). The error says that it is detected but not be identified properly. I went through all the troubleshooting steps including resetting my ipod, re-starting the driver, re-installing iTunes but nothing works. Interestingly, if iTunes is not open, I can see the iPod as a storage device, I can open and browse it. So I assume there is no error with the wire, the iPod itself or the driver. As soon as iTunes gives the above error, it stops being visible as a storage device. How can I fix this?

Aridra,
Thanks very much for this - I had exactly the same problem; went through the same steps to no avail unitl I read your post. Similarly, I uninstalled EVERYTHING Apple on my PC and re-installed. Bingo !! my iPod is now recognised and synched.

D-Link DIR-615/Macbook detecting but not connecting

Similar Messages

Maybe you are looking for