D-Link DIR-615 (Rev H1(!)) does not work with Airport Express?

Hi there,
I had my AirPlay working just fine with my Airport Express (AX) and my wireless N Router D-Link DIR-615 (Rev. B2). Now I changed my Internet provider and received a D-Link DIR-615 (Rev. H1) and I cannot find my AX anymore (I mean, it's still here, but the AirPort Utility cant find it!)
Are there known issues between those two?
(The Rev. H1/B2 is the Hardware Version of my D-Link DIR-615. The Firmware is up-to-date (8.01 I think))
The status light is a solid, beautiful green.
I already tried the following:
- restart the AX, the D-Link and my MacBook (10.7.2)
- changed from AES to TKIP (found that somewhere in the internet)
- Reseted my AX to factory settings and configured everything new. (via Ethernet)
Probably interesting:
- After resetting to factory settings and configuring everything new, the AX showed up in iTunes, but when I tried to connect with it, it kept me waiting for 1-3 Minutes and simply did not connect w/o error message. The AX disappeared after restarting iTunes.
I'm running out of solutions..
Anyone a good question/suggestion or answer for me?
greetings
squob

Only way I see out other than waiting, is to hook he Drive to a Mac, (FW preferable for speed), then get Tri-Backup...
http://www.tri-edre.com/english/tribackup.html
Which can be set to trigger Backups when Shares mount.

Similar Messages

HP LaserJet 1000 not working with Airport Express

Has anyone had any luck getting a HP LaserJet 1000 working with Airport Express on Windows XP or even OS X for that matter?
I can connect to the Airport Express device using iTunes, but its pretty muched gimped for printing. uggh.
MacBook Pro Mac OS X (10.4.6) D-Link DI-524

I've no personal experience with your particular printer but these pages may help you
http://h20000.www2.hp.com/bizsupport/TechSupport/Home.jsp?&lang=en&cc=uk&prodTyp eId=18972&prodSeriesId=45674&submit.y=7&submit.x=4&lang=en&cc=uk
http://www.ifelix.co.uk/tech/1013.html
Steve

Mac OS X not working with Airport Express but Win XP is ok on the same iMac

Hello everyone,
as the message says I am having troubles with Airport Express.
To say it quickly, I live in a house share in London, and everyone in the house enjoys the wifi without troubles. I do as well with my macbook from every point of the house.
The troubles are with the big iMac: with mac os the internet signal won't just work at all, pages take minutes to load with both safari and firefox, and most of the times the loading times out.
I thought it was a signal power problem, but the weirdest thing of them all is that... when I switch to Windows XP on the same iMac (and right now I am writing from that!) the internet works perfectly!
Then I switch to mac os again... and slow internet again!
Anyone has an idea of what could this be?
Many thanks for the support

Yes, I just discovered this problem on my own machine.
I just wanted to check some settings and discovered that the behaviour of the GUI of Server Admin was somewhat "erratic": First this "no services are configured" message. Some of the configured servers were marked with the usual green "up and running" bullet, others dark grey - those were normally configured and running and clicking the appropriate line seemed to force Server Admin to check the actual state and then turned also green. But sometimes configuration pages were "greyed out", or while switching through the tabs Server Admin claimed that where were "unsaved changes" which should be saved (or discarded).
And then SMB: this was light grey, as usual when a service is not running and clicking on it I browsed through the configuration tabs - everything seemed ok (all my settings were correctly shown, configured as PDC with right domain name etc.) - and I started the service. Then suddenly the configuration settings changed to the default settings - no more PDC, but a "standalone server" with workgroup name "WORKGROUP"...
Looks for me, as if Server Admin lost it's "source" file for the configuration (the file in /var/db/smb.conf says, that it is automatically generated -- does somebody were the source file is stored?)...

HT1145 Why is iOS 5.1 AirPlay not working with Airport Express

Ive updated my iPad and iphone to iOS 5.1 and now AirPlay is not working with my Airport Exress set up.
Can anyone help me out? I can't seem to resolve this and I'm an apple head

I have the same problem from my Ipad 2 and my Iphone 4S trying to airplay to my Apple TV 2. i dont get any airplay button when playing photos or \video.
All worked fine with IOS 5.0
Whats going on?

Hands Free Link (HFL) on Acura TL does not work with iPhone 3G

I pair iPhone successfully, and can pick up the incoming calls. However, when I make an outgoing call on iPhone, and tell it to use HFL, the call is not transferred to HFL.
HFL works fine with my Treo 650, including picking the outgoing calls.
Is there a software update or setting for either iPhone or Acura?
Thanks,
Inna

InnaB, this is an issue with iPhone. This is just MY speculation, hope Apple will release a fix soon. You can also leave a feedback here http://www.apple.com/feedback/iphone.html and PLEASE enter specific information of vehicle like Model, year and type of radio or Audio System your vehicle is equipped with when you fill out that feedback. I have encountered similar issues with other makes of cars too as I do a lot of testing of cars.There are some vehicles that work fine and then there are some that exhibit concerns like yours.
On a side note have you tried to RESET NETWORK settings and tried? Also unpair ALL BT sets, re-pair the iPhone to your vehicle and try it. Some instances I have encountered where the IiPhone was STILL paired to a HEADSET, it would NOT release it to work with another BT device. Some car audio systems have what's called an "Auto Pairing" which works awesome with iPhone, where you DONOT have to worry at all, start the vehicle, turn on audio system, iPhone auto pairs to that system. I donot know IF your vehicle is equipped with that design, check in the user manual of that system please.

Does airplay work with airport express without wifi?

I would like to stream music from my Macbook Air to my stereo using Airport Express. However, it is my weekend home in which there is no wifi connection. Will it still work or does Airplay require a wifi conenction to the internet to work?

Yes, you should be able to get it to work. I tried it just now with an older AirPort Express, and it works for me, but the configuration and settings are rather unconventional.
Set the AirPort Express to create a wireless network with no security code— it may work with one but maybe not. Configure the AirPort Express in Bridge Mode with respect to the Internet, and assign it a static IP address of, say, 192.168.4.1.
I made a wireless connection to the AirPort Express from an iPhone 5 and was able to play music from my iPhone to speakers attached to the AirPort Express. Interestingly, the iPhone doesn't actually make a full connection to the AirPort Express but the wireless network name shows up in its Settings.
The iPhone has a self-assigned 169.x.x.x IP address, but I am able to choose the AirPort Express-attached speakers from the Music app on my iPhone.
There may be a cleaner way to do this, but one way or another you should be able to get it to work.

Time capsule base station not working with Airport Express

Hi...
I have a network setup using the airport base station hat is part of my (older) time capsule. I also have an older Airport Express.
My network is working fine...and looks like the first image below. When I plug in the Airport Express and reset it...I get what you see on the second image. The thing is...the airport utility is supporting the base station just fine prior to looking for the airport. I presently have airport utility 6.3.2 and my airport base station has firmware 7.6.4.
Any help would be great....thanks!

Your express is a G wireless model and not compatible with the N wireless TC.
You can use it but only by using it with ethernet and setting it up as AP.. you also need to use 5.6 utility not v6.. apple removed support for G wireless devices from v6.
LOL..
I was 2min late.

Xbox 360 not working with Airport Express

I have a Airport Extreme router and I just bought a airport express so I can wirelessly relay the signal and hook up my xbox 360 to the express. I put it in WDS mode and it worked fine up until the xbox 360 ran the IP address test. It didn't pass the IP and my settings were on automatic. I thought the Express acts as a extension to the Airport but I guess not. Are there any settings I can change to make this work? Please help.

Same issue you have except I never connected the printer directly to my Mac via the USB. Went straight to the wireless Airport Base Station and connected the printer. Printer is found in "Printer Setup Utility" and connected via "Bonjour", unsure what that is. However the *"Printer Setup Utility"* is asking me to select: *"Print Using"* and giving choices such as CANON BJC-1000 - GIMP-PRINT v5.0.0 beta2. I am unsure what to select. And the printer still doesn't print even with one of these 20 choices selected. Any ideas from anyone?

BT Home Hub not working with Airport Express

We have just moved house and had BT Internet installed. It uses the very latest Home Hub but this is causing the Airport Express to fail.
On occasion it works but more often than not the connect is lost and the MacBook/Airport Utility fail to see the AE's again.
What can I do to keep my Airport network up and running all the time. I NEVER used to have this problem with my old set up at my home house.

Whenever you make a change on your network.....in this case a new router......you need to reset the AirPort Express back to factory defaults and then reconfigure it again to work in the new environment.
Power down the AirPort Express
Hold in the reset button on the AirPort Express and keep holding it in for another 8-10 seconds as you plug the Express back in to power
Release the reset button
Allow 40-45 seconds for the AirPort Exrpess to restart
Open AirPort Utility and click Continue to follow the guided setup to configure the Express to "join" your wireless network.

Photosmart C4280 not working with Airport Express

I have a Photosmart C4280 connected to an Airport Express Base Station via USB for wireless printing. I have two computers that I want to use for printing - an iMac and a Toshiba laptop running Windows XP. Printing from the Mac works perfectly and required zero configuration. On the laptop I created the printer using Bonjour. It located the printer on the network without a problem and I selected the driver for the HP 4200 Series printer. However, when I try to print, the print job sits in the qeue and eventually I receive an error message that it couldn't print.
I have disabled the Norton and Windows firewalls but that doesn't solve the problem. I have also tried some generic drivers but that didn't work. Does anybody have any additional suggestions?
Thanks in advance.

Check out http://discussions.apple.com/message.jspa?messageID=8883084#8883084
It describes a Vista/AirPortExpress/C4280 installation, but should be relevant to XP.

Airport card does not work with Airport Extreme when security is turned on

I have an iMac running OSX 10.4.11 with an Airport card installed (firmware version 9.52).
I recently replaced my Netgear wireless router with an Apple Extreme Base station and now I am not able to connect my iMac to the wireless network when WEP security is turned on - I get an error from the Airport Setup Assistant when I attempt to connect to the wireless network.
It works fine if the wireless security on the Extreme Base station is turned off.
Please help and thanks in advance.
Motasim

First, I highly recommend that you switch to either WPA or WPA2 as WEP is no longer considered secure. If you must use WEP, I suggest that you try the following:
o Re-create the Network Name (SSID) on your AirPort Extreme Base Station (AEBS)
o Try using 128-bit WEP, with a 26-Hex character key for the encryption type.

Canon Pixma MP520 does not work with Airport under Leopard

Before this printer MP520 worked without any problem.
After installing Leopard, I can print through USB but not through Airport.
I installed all latest updates for Leopard, firmware for Airport and even the latest Canon driver.
I can see the printer in my Bonjour list. Then it looks like it's connecting and then an error window pops up. Error A 306, print attempt failing.
I also restarted Airport with and without printer connected.
Any hint is welcome

Resolved after complete re-installation of MAc OS X

DOES THIS WORK WITH AirPort Express Base Station with AirTunes?

If i purchase AirPort Express Base Station with AirTunes, will I be able to hook it up to the speakers of my home dvd theatre system?
Also whiich is better, the AirPort Express Base Station with AirTunes or the Refurbished AirPort Express Base Station with AirTunes?
THANK YOU.

If i purchase AirPort Express Base Station with
AirTunes, will I be able to hook it up to the
speakers of my home dvd theatre system?
I would say yes.
Also whiich is better, the AirPort Express Base
Station with AirTunes or the Refurbished AirPort
Express Base Station with AirTunes?
They are the same, just happens one has already been used/owned/overstocked/etc...
iFelix

Imac internet not working with airport express

Hi there,
I purchased an imac for my upstairs bedroom, but the signal from the time capsule was weak, so I bought an airport express and set it up. But still I cannot connect to internet even though after running the network diagnostics say I am connected to internet. My macbook works perfectly in the bedroom with all airport bars working, but the imac still has only two bars. I've tried everything, help!!

Same issue you have except I never connected the printer directly to my Mac via the USB. Went straight to the wireless Airport Base Station and connected the printer. Printer is found in "Printer Setup Utility" and connected via "Bonjour", unsure what that is. However the *"Printer Setup Utility"* is asking me to select: *"Print Using"* and giving choices such as CANON BJC-1000 - GIMP-PRINT v5.0.0 beta2. I am unsure what to select. And the printer still doesn't print even with one of these 20 choices selected. Any ideas from anyone?

External USB HD does not work with HAL:

External USB HD does not work with HAL:
From the last 10 days the HAL auto-mount with ntfs-3g file system of my external hard drive does not woks.
But the manual mount procedure with the command mount -t ntfs-3g /dev/sdb* /mnt/XYZ works.
I've followed the instructions in the wiki: http://wiki.archlinux.org/index.php/HAL and the system has worked up to the last kernel or HAL update.
My fat32 usb-stick works without any problem.
If I try to open the device with KDE it appears an error popup wit this message:
TODO: have to rethink extra options
Error: kio_media_mount_helper
The log from the kernel.log is
Nov 6 22:03:16 myhost usb 5-1: new high speed USB device using ehci_hcd and address 4
Nov 6 22:03:16 myhost usb 5-1: configuration #1 chosen from 1 choice
Nov 6 22:03:17 myhost Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
Nov 6 22:03:17 myhost ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Nov 6 22:03:17 myhost Initializing USB Mass Storage driver...
Nov 6 22:03:17 myhost scsi6 : SCSI emulation for USB Mass Storage devices
Nov 6 22:03:17 myhost usb-storage: device found at 4
Nov 6 22:03:17 myhost usb-storage: waiting for device to settle before scanning
Nov 6 22:03:17 myhost usbcore: registered new interface driver usb-storage
Nov 6 22:03:17 myhost USB Mass Storage support registered.
Nov 6 22:03:22 myhost scsi 6:0:0:0: Direct-Access WDC WD32 00JB-00KFA0 0811 PQ: 0 ANSI: 0
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Test WP failed, assume Write Enabled
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Test WP failed, assume Write Enabled
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
Nov 6 22:03:22 myhost sdb: sdb1
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Attached SCSI disk
Nov 6 22:03:22 myhost sd 6:0:0:0: Attached scsi generic sg2 type 0
Nov 6 22:03:22 myhost usb-storage: device scan complete
and the error.log is
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
Do you have some idea ....
Bye.

I have done the following:
Downloaded the patched hal version.
used makepkg in /abs/local/trunk/ to create a pkg for pacman
used sudo pacman -U pkgname to install it.
used sudo nano /etc/hal/fdi/policy/preferences.fdi to create the fdi file with the following content:
saved the file and removed my ntfs entryes from fstab and rebooted. and still there is no automount off ntfs partitions.
have i done something wrong?
br fjodork
WARNING: what follows is a guide of what did work for me, I'm still in an early stage of learning linux, so please correct me if anything of what follows is wrong/dangerous/stupid. As I said, this worked for me, it's not pretty, since I was learning each step on the fly and I'm sure there are better ways to do this.
So fjodork, you seem to have done the the necessary steps, though i couldn't get it to work until i first removed hal without dependencies
pacman -Rd hal
it will give you some warning about the dependencies, ignore it since we are reinstalling hal in a few steps.
First i tried to follow Raymano's link, obviously it showed me nothing in the browser so I thought it might be a broken link.
So I downloaded the source tarball from here http://hal.freedesktop.org/releases/hal-0.5.10.tar.gz
unpacked it changed the /tools/hal-storage-mount.c as per Milfadoodle's instructions.
at first I tried to compile directly from source, the process would finish without a glitch though after reboot nothing changed, as if hal weren't
installed, i guess there were issues with paths. anyway read on
Then repacked the source in tarball, copied it to /var/abs/extra/system/hal and modified the PKGBUILD as follows
makedepends=('pkgconfig' 'gperf')
options=('!libtool')
install=hal.install
source=(${pkgname}-${pkgver}.tar.gz #removed url so makepkg looks in the current directory for the tarball
hal
hal-policy.patch
cryptsetup_location.patch
hal-0.5.9-hide-diagnostic.patch
ntfs3g-valid-options.patch)
md5sums=('6641c30a27c00485c6accac5110ff911' # replace with md5sum of your package's sourceball (run md5sum filename)
'882f67668cb14a0a9e4a27ef22278027'
'5ba8b610aa9763a5f42b9f7cbd7a86ad'
then makepkg (i had to add --asroot, don't ask why
and finally pacman -U hal-0.5.10-1-i686.pkg
another reboot and everything worked without a glitch!:D (yeah i know i still haven't got rid of the reboot mentality )
I have also put the policy files as per the wiki instructions.
PS: I know this is a dirty way to getting things done but as i said, I'm just starting
If anyone could comment/correct/explain this post I'd be more than happy, the automount issue was bothering me for about a month now (you'll say why do I need ntfs in the first place? well, I only recently switched for Linux as my primary OS, these are some relics of the M$ era

D-Link DIR-615 (Rev H1(!)) does not work with Airport Express?

Similar Messages

Maybe you are looking for