D400 - system status LED blinking, network LED blinking

Hi - Just recently started experiencing this problem with my D400.
The system status LED is blinking, which according to the user guide means that WHS is either booting or shutting down.  The Network LED shows activity. 
Problem is that I can't get on the D400 via remote desktop.
Frustrating.  Talked with support already, said only option is to send in to depot or find a local resource to troubleshoot or fix.  Problem is that we have our music/photos on this thing. 
Support also said that if we factory reset data on all drives will be erased.
Looking for help wherever I can get it.  Thanks!
Scott

Hi scottdcm, and welcome to the Lenovo User Community!
To get your music/photos off the system before returning it for service, connect the hard drive(s) to another computer with a SATA connection. An external USB/SATA connector or drive enclosure will also do the job.
You can also remove any drives you have added before shipping it for service.
Hope this helps!
I don't work for Lenovo. I'm a crazy volunteer!

Similar Messages

  • UCS240 M3 System status LED Amber blinking

    Hi Guys
    I have a alarm in the UCS240 . The System status LED Amber is blinking, but in the vCenter nothing appears abnormal.
    Please see the captures:
    -System Event
    -System Status
    - CPU
    - Memory
    - Storage
    -Temperature
    -Platform Alert
    TIA
    Cristian

    Dear Eric
    Time :Fri Dec 20 12:55:17 2013
    Severity :Warning
    Code :F1008
    DN :sys/rack-unit-1/board/storage-FLASH-ctlr-1/vd-HV
    Probable Cause :equipmentDegraded
    Description :Flex Flash Virtual Drive HV Degraded: please check the flash device or the controller
    TIA.
    Cristian

  • SUN Fire V65 - System Status LED - non-critical condition

    Hi guys
    We have a Checkpoint Cluster which is made up of 2 Sun Fire V65 servers.
    The front panel of the servers are showing the System Status LED lights as Blinking Amber , which sun documenation has listed as
    "Blinking amber: Indicates the system is in a non-critical condition" ref: http://dlc.sun.com/pdf/817-2024-12/817-2024-12.pdf
    We have resetead the hardware, cleared ,logs, even change HW etc. The light goes away for some time and then returns.
    Can anyone advise on what to do?
    Sun has the following listed in their Troubleshooting pdf i ref before
    "Non-Critical Condition
    A non-critical condition is indicated with a blinking amber status LED and signifies
    that at least one of the following conditions is present:
    ¡ Temperature, voltage, or fan non-critical threshold crossing.
    ¡ Chassis intrusion.
    ¡ Satellite controller sends a non-critical state, via the Set Fault Indication
    command, to the BMC.
    ¡ A Set Fault Indication command from the system BIOS. The BIOS may use the Set
    Fault Indication command to indicate additional, non-critical status such as
    system memory or CPU configuration changes"
    Is there any Unix / Linux / SPLAT logs I can look at or debugging we can look at.
    Thanks in advance

    Your initial description mentions that you have swapped various pieces of hardware around. I presume that means you used current parts instead of new-never-used components. Are both of the clustered systems showing the same symptoms?
    I can only think of a couple of additional things to try.
    Firstly, those are old boxes. V65's went EOL in January 2005, so yours are at least that old if not older. They are x86 architecture. Have you replaced the CR2032 CMOS battery that's on the systemboard? Have you additionally checked for voltage fluctuations in the data center? A marginal power supply can "mostly work" but it can be effected by an AC mains issue.
    If that doesn't change anything, then you may need to contact Checkpoint. They may be able to point you toward some sort of heartbeat function that is tripping a fault level when it flip-flops between the two systems.
    That's a software investigation and would be outside the scope of this forum.

  • C220 M3 System Status LED is Amber

    Hello All,
    I have a C220 M3 server that is running one of our CUCM subscribers and Unity Connection subscriber. I noticed today that it has an Amber light on the chassis. I have looked in VCenter, the ESX host screen, and even the Call Manager application for error statuses, but no errors are mentioned. For some reason, I cannot access the CIMC on that server and the IP address I have for the CIMC is not responding to Pings. Is there any other place I can look to discover what is causing this error light to be on?
    Thanks.

    Dear Eric
    Time :Fri Dec 20 12:55:17 2013
    Severity :Warning
    Code :F1008
    DN :sys/rack-unit-1/board/storage-FLASH-ctlr-1/vd-HV
    Probable Cause :equipmentDegraded
    Description :Flex Flash Virtual Drive HV Degraded: please check the flash device or the controller
    TIA.
    Cristian

  • Cisco 1131AG LWAP status led yellow and other leds blinking green

    I have a problem with three AIR-LAP1131AG-E-K9  that joined the controller and the status led turns to yellow after joining the controller while other LEDs are blinking green.
    The APs has no coverage at all although the WCS shows that there is coverage and the 4400WLC shows that the AP interfaces are UP. (The ethernet interface and tha 802.11b,g radio interface is up).
    The SSID broadcast is enabled.
    On the switch the interface is up and there is traffic going in and out of the LAP.
    I tired power reset and factory reset for the APs but the problem remains the same.
    Any ideas for what might be the problem ?!!
    Regards

    Yes the clients are not able to see the SSID broadcasted by the AP.
    But these APs were functioning normally before without any changes to the WLC config.
    I had the same problem with other APs but they went back to normal state after a hardware reset to the APs.

  • FP-1600 Status LED blinks 17 times.

    My FieldPoint bank has 9 modules. I previously had a problem with the FP-TB-10 power and ready lights blinking, but that was because one of my dual-channel modules was not seated correctly. Now the status LED is blinking 17 times. The manual says to contact NI about this. The FieldPoint Explorer seems to find all of the modules correctly, though. Anyone know what's up?

    Aaron,
    I checked the firmware and the FieldPoint Explorer version, and I'm using 3.20 and 3.0, respectively. When I power cycle the FP-1600, the 17 blinks of the status LED go away. Communication works, and all of the devices are found. However, communication does drop out from time to time, and eventually the status LED begins blinking 17 times again.
    A possibly related issue is that the FP-AI-V10 dual-channel module that I have plugged into slot 2 of the FP-TB-10 base causes the FP-TB-10 to flash its power and ready LEDs. Re-seating the FP-AI-V10 seems to fix this, although the module is definitely already clicked into place when I see this problem. Upon reseating (or just pressing on it without removing the module), the FieldPoint Explo
    rer program finds this module.
    I'm tempted to think that this issue with the FP-TB-10 and FP-AI-V10 are unrelated to the FP-1600's status LED blinking 17 times because even with the FP-TB-10 removed from the bank, I still get the flashing LED.
    Any ideas? Also, what is a GPF type error?
    Thanks,
    Jake

  • Sun Fire X2100  Blinking Status LED...

    We have 3 new Sun Fire X2100 servers at my current job. Just recently the status LED (orange) started blinking. The logs show fine and running a prtdiag shows everything up and running fine. Is there a way to turn off the blinking LED? I have gone over every piece of information I can find and have found nothing about how to turn this off once it has started blinking.

    This may be one of two issues:
    - There's a know ILOM/nge driver bug in eariler releases of S10 x86 (pre 6/06).
    - There's a know issue with an older firmware rev of the BIOS/LOM where the net management port hangs/drops out and triggers the blinking fault LED. Do you know what BIOS revision you are at?
    Most times a mobo swap is NOT the fix. You may be making the problem worse because we have mobos in the supply chain with older firmware revisions.
    On the X2100's I usually have my customers try:
    - Moving the RAM in different slots
    - Updating the BIOS/LOM firmware
    - Running the PC-Check diags
    ... before I send a field tech out to do major surgery.

  • CIsco AIR LAP1131AG E K9 Status LED = Yellow; Ethernet LED = Off; Radio LED = blinking Red, what is this? it isn't in the manual

    CIsco AIR LAP1131AG E K9 Status LED = Yellow; Ethernet LED = Off; Radio LED = blinking Red in a pattern, red off then red red, Our AP isn't working it won't show up on our Cisco WLC 2125 anymore and this is the LED indicators, I've checked in the manual and this combination of LEDs do not exists??

    No cisco web is working perfectly.
    do you have a valid CCO id with smarnet contract ?? then only you can download new IOS for AP:
    Autonomous AP image:
    http://software.cisco.com/download/release.html?mdfid=279537722&flowid=6775&softwareid=284180979&release=12.4.25d-JA2&relind=AVAILABLE&rellifecycle=ED&reltype=latest
    LAP AP image:
    http://software.cisco.com/download/release.html?mdfid=279537722&flowid=6775&softwareid=280775090&release=12.4.25e-JAP&relind=AVAILABLE&rellifecycle=ED&reltype=latest
    Regards

  • NI smart camera 1764 Status LED Blinking

    I am using NI smart camera 1764. when i am giving 24 V DC supply to the camera then Power & Status LED is blinking continuously in RED colour. on the other hand pass & fail LED also blinking in RED & GREEN colour alternatively. i am not able to connect camera to my computer through ETHERNET cable & cannot use for my application. 
    Please suggest me the solution as soon as possible.

    Have a look at chapter 6 of this manual:
    http://www.ni.com/pdf/manuals/372429b.pdf
    Adnan Zafar
    Certified LabVIEW Architect
    Coleman Technologies

  • Fp-2000 status LED starts blinking

    The status led of my FP-2000 started blinking twice after turning off my module  and turning  it on again, I already updated the firmware to version 10.4 following the indicated steps. I already tried in safe mode, also reset and format disk , always after configuring  the IP the status button starts blinking twice, again.
    Thank you for your support

    Hi Srael
    Try following this document to see if you can solve the problem
    http://zone.ni.com/devzone/cda/tut/p/id/4466
    Greetings
    Julio Mena

  • CFP 2110 - Status led flashing continously

    I'm running into problem with a cFP 2110.
    During the debugging of my RT application on the cFP, I get an error message "Host IP address not in the access list". At this time, I was unable to download any application to the cFP. the VI server IP access list was configured with *. So all the IP address can access to the cFP.
    I found a procedure on the ni web site to reset the system.
    -Set to safe mode
    -ftp the cFP and delete all the file
    -Remove the safe mode.
    It means that there is no more OS or LabVIEW RT on the system.
    Now, When I restart the cFP, the Status led is flashing continously (1 flash / 1.5s) and I don't have access anymore to the cFP in MAX.. Can some one help me on this case ? .
    Thanks
    Attachments:
    Ni_recommendations.pdf ‏126 KB

    Hi Poussin,
    I would recommend flipping the Reset IP dip switch (dip switch 7).  This
    should get the controller to show up in Measurement and Automation
    Explorer(MAX) as 0.0.0.0.  If you can't see the controller, you may want
    to try turning off your firewall.  Often computer firewalls will prevent
    customers from seeing unconfigured controllers in MAX. 
    Once you find your controller, you can flip the reset IP dip switch back to the
    off position and reset the IP address.  For more information on this,
    click on your FieldPoint controller in MAX that will be displayed as
    0.0.0.0.  In the MAX help that appears on the right, click on the link
    titled, "Configure Network Settings."  If you need assistance
    choosing an IP address, please look at this KnowledgeBase. 
    Once you have assigned an IP address to the controller, the status light should
    stop blinking once.   You will then need to install software. 
    Here is a general
    document that describes how to assign an IP address and install software.
    Please let me know if you have any other questions.
    Regards,
    Ching P.
    DAQ and Academic Hardware R&D
    National Instruments

  • How to turn OFF status LED on VC220?

    I'm looking for a way to turn off the status LED on a VC220.  This is not the IR LED, but instead the large blinking LED on the front.
    The documentation mentions that it can be turned off, but I can't find a menu option for this.
    Thanks for your help!
    --Joe
    Status LED
    Indicates the following status:
    LED Off—The power is off or the LED status is turned off.
    Flashing green in one second intervals—The camera and network is functioning.
    Steady orange—The camera can’t detect a networking signal; thus the camera is not functioning. For example, the Ethernet cable is not attached.
    Flashing orange—The PIR sensor noted movement. Flashing green rapidly—The firmware is being
    upgraded.
    Flashing orange rapidly—The camera’s default settings are being restored.
    Alternating flashing green and orange—Video has been lost.

    Joe,
    Use the Network Setting > IP Setting page to set the IP address and other related
    settings. When you complete the configuration, click Save to save the settings;
    otherwise click Cancel to discard the changes.
    • Disable LED Operators—Select to disable the LED illuminators. You may
    choose to do this if you don't want to alert others that the network camera is
    on. Use the Network Setting > IP Setting page to set the IP address and other related
    settings. When you complete the configuration, click Save to save the settings;
    otherwise click Cancel to discard the changes.
    http://www.cisco.com/en/US/docs/security/csbvsc/vc220/administration/guide/VC220AdministrationGuide.pdf
    page; 41
    Hope this is what you're looking for,
    Jasbryan

  • FBUS-HSE/H1 not detecting 100Mbps and status light blinking green

    I had the HSE/H1 connected to my network, but it decided to go crazy on me and drop off the map. I know the IP Address of the unit, but am unable to connect with it anymore. I did a factory reset on the unit, but am unsure if that resets the IP address as well. If that is the case what is the best way to force an IP address on the unit? The status light blinks green at a rather fast rate as well. I can add the ethernet interface board in the interface fonfiguration utility, but can not add the hse/h1 LD since it just sits there and listens for the board forever. I hope it is an easy fix and not a matter of the unit died on me.
    Thanks
    Kyle

    The blinking status LED indicates that the linking device is in standby state. The linking device will be assigned an IP address automatically through DHCP. 
    Please check whether the linking device and the host PC are in the same subnet. Otherwise, the linking device will not be detected.
    Feilian (Vince) Shen

  • WiSM Status LED 1 & Status LED 2 showing off. Is it normal?

    Hi,
    WiSM WLAN Service Module WS-SVC-WISM-1-K9 in 6509e running VSS IOs s72033-ipservicesk9_wan-mz.122-33.SXI2a.bin having trouble to get the IP from service-vlan DHCP also status LED 1 & Status LED 2 showing off.
    The pertinent config is as follows.
    vlan 300
    name WiSM_Service_Vlan
    interface Vlan300
    description *** WiSM Service-Vlan
    ip address 192.168.200.1 255.255.255.0
    ip dhcp excluded-address 192.168.200.1
    ip dhcp pool WiSM_Service-Vlan_300
       network 192.168.200.0 255.255.255.0
       default-router 192.168.200.1
    wism service-vlan 300
    vlan 183
    name WiSM_Management
    interface Vlan183
    description *** WiSM Management Vlan ***
    ip address 10.39.139.254 255.255.255.0
    wism switch 1 module 4 controller 1 allowed-vlan 125,126,183,300
    wism switch 1 module 4 controller 2 allowed-vlan 125,126,183,300
    wism switch 2 module 4 controller 1 allowed-vlan 125,126,183,300
    wism switch 2 module 4 controller 2 allowed-vlan 125,126,183,300
    wism switch 1 module 4 controller 1 native-vlan 183
    wism switch 1 module 4 controller 2 native-vlan 183
    wism switch 2 module 4 controller 1 native-vlan 183
    wism switch 2 module 4 controller 2 native-vlan 183
    HO2NET0001#sh wism status
    Service Vlan : 300, Service IP Subnet : 192.168.200.1/255.255.255.0
          WLAN
    Slot  Controller  Service IP       Management IP    SW Version  Status
    ----+-----------+----------------+----------------+-----------+---------------
    20    1           0.0.0.0          0.0.0.0                      Service Port Up
    20    2           0.0.0.0          0.0.0.0                      Service Port Up
    HO2NET0001#sh module
    Mod Ports Card Type                              Model              Serial No.
      1    8  CEF720 8 port 10GE with DFC            WS-X6708-10GE      SAL13442Q5N
      2    8  CEF720 8 port 10GE with DFC            WS-X6708-10GE      SAL13442GAL
      3   48  CEF720 48 port 10/100/1000mb Ethernet  WS-X6748-GE-TX     SAL13410N8P
      4   10  WiSM WLAN Service Module               WS-SVC-WISM-1-K9   SAD133101UY
      5    5  Supervisor Engine 720 10GE (Active)    VS-S720-10G        SAL13442JE4
    Mod MAC addresses                       Hw    Fw           Sw           Status
      1  0025.84f1.55b8 to 0025.84f1.55bf   2.1   12.2(18r)S1  12.2(33)SXI2 Ok
      2  0025.84f1.4e58 to 0025.84f1.4e5f   2.1   12.2(18r)S1  12.2(33)SXI2 Ok
      3  0027.0da7.c240 to 0027.0da7.c26f   3.2   12.2(18r)S1  12.2(33)SXI2 Ok
      4  0023.5e25.7168 to 0023.5e25.7177   2.3   12.2(14r)S5  12.2(33)SXI2 Ok
      5  001f.9e2a.2608 to 001f.9e2a.260f   3.1   8.5(3)       12.2(33)SXI2 Ok
    Mod  Sub-Module                  Model              Serial       Hw     Status
      1  Distributed Forwarding Card WS-F6700-DFC3C     SAL13442EG9  1.4    Ok
      2  Distributed Forwarding Card WS-F6700-DFC3C     SAL13442H9T  1.4    Ok
      3  Centralized Forwarding Card WS-F6700-CFC       SAL13442HU9  4.1    Ok
      4  Centralized Forwarding Card WS-SVC-WISM-1-K9-D SAD133200D6  2.1    Ok
      5  Policy Feature Card 3       VS-F6K-PFC3C       SAL13442E5S  1.1    Ok
      5  MSFC3 Daughterboard         VS-F6K-MSFC3       SAL13421AJZ  2.0    Ok
    Mod  Online Diag Status
      1  Pass
      2  Pass
      3  Pass
      4  Pass
      5  Pass
    HO2NET0001#sh vlan
    300  WiSM_Service_Vlan                active    Gi1/4/9, Gi1/4/10
    The service IP is supposed to have been populated with an address from the dhcp pool. I am also unable to connect to access it by console as well as doing a session switch 1 slot 4 processor 1. I get the following upon attempting to do so:
    Through Console.
    It is giving following & then got stuck.
    Bootloader 3.2.202.0 (Nov 13 2007 - 19:35:12)
    Motorola PowerPC ProcessorID=00000000 Rev. PVR=80200020
            CPU: 999 MHz
            CCB: 333 MHz
            DDR: 166 MHz
            LBC: 41 MHz
    L1 D-cache 32KB, L1 I-cache 32KB enabled.
    I2C:   ready
    DTT:   1 is 33 C
    DRAM:  DDR module detected, total size:512MB.
    512 MB
    8540 in PCI Host Mode.
    8540 not PCI Arbiter.
    Memory Test PASS
    FLASH:
      Flash Bank 0: portsize = 2, size = 8 MB in 142 Sectors
    8 MB
    L2 cache enabled: 256KB
    Card Id: 1537
    Card Revision Id: 1
    Card CPU Id: 1287
    Number of MAC Addresses: 32
    Number of Slots Supported: 4
    Serial Number: FAM133200D6
    Manufacturers ID: 30464
    Board Maintenance Level: 00
    In:    serial
    Out:   serial
    Err:   serial
                          .o88b. d888888b .d8888.  .o88b.  .d88b.
                         d8P  Y8   `88'   88'  YP d8P  Y8 .8P  Y8.
                         8P         88    `8bo.   8P      88    88
                         8b         88      `Y8b. 8b      88    88
                         Y8b  d8   .88.   db   8D Y8b  d8 `8b  d8'
                          `Y88P' Y888888P `8888Y'  `Y88P'  `Y88P'
                        Model SVC-WiSM   S/N: FAM133200D6
    Net:   TSEC ETHERNET
    IDE:   Bus 0: OK
      Device 0: Model: STI Flash 8.0.0 Firm: 01/17/07 Ser#: STI1MMJ109198093647
                Type: Removable Hard Disk
                Capacity: 488.7 MB = 0.4 GB (1000944 x 512)
      Device 1: not available
    Booting Primary Image...
    Press <ESC> now for additional boot options...
    Detecting Hardware . . .
    Cryptographic library self-test....passed!
    XML config selected
    Validating XML configuration
    Cisco is a trademark of Cisco Systems, Inc.
    Software Copyright Cisco Systems, Inc. All rights reserved.
    Cisco AireOS Version 5.2.178.0
    Initializing OS Services: ok
    Initializing Serial Services: ok
    Initializing Internal Interfaces: ok
    Initializing Network Services: ok
    Initializing Licensing Services: ok
    Starting ARP Services: ok
    Starting Trap Manager: ok
    Starting Network Interface Management Services: ok
    Starting System Services: ok
    Starting FIPS Features: ok : Not enabled
    Starting Fast Path Hardware Acceleration: ok
    Starting Switching Services: ok
    Starting QoS Services: ok
    Starting Policy Manager: ok
    Starting Data Transport Link Layer: ok
    Starting Access Control List Services: ok
    Starting System Interfaces: ok
    Starting Client Troubleshooting Service: ok
    Starting Management Frame Protection: ok
    Starting LWAPP: ok
    Starting CAPWAP: ok
    Starting Certificate Database: ok
    Starting VPN Services: ok
    Starting Security Services: ok
    Starting Policy Manager: ok
    Starting Authentication Engine: ok
    Starting Mobility Management: ok
    Starting LOCP: ok
    Starting Virtual AP Services: ok
    Starting AireWave Director: ok
    Starting Network Time Services: ok
    Starting Cisco Discovery Protocol: ok
    Starting Broadcast Services: ok
    Starting Logging Services: ok
    Starting DHCP Server: ok
    Starting IDS Signature Manager: ok
    Starting RFID Tag Tracking: ok
    Starting WLAN Control Protocol (WCP): ok
    Starting Mesh Services:  ok
    Starting TSM: ok
    Starting CIDS Services: ok
    Starting Ethernet-over-IP: ok
    Starting DTLS server:  enabled in CAPWAP
    Starting FMC HS: ok
    Starting WIPS: ok
    Starting SSHPM LSC PROV LIST: ok
    Starting Management Services:
       Web Server: ok
       CLI: ok
       Secure Web: Web Authentication Certificate not found (error). If you cannot access management interface via HTTPS please reconfigure Virtual Interface.
    (Cisco Controller)
    Welcome to the Cisco Wizard Configuration Tool
    Use the '-' character to backup
    Would you like to terminate autoinstall? [yes]:
    AUTO-INSTALL: starting now...
    Through Session
    HO2NET0001##session switch 1 slot 4 proc 1
    The default escape character is Ctrl-^, then x. You can also type 'exit' at the remote prompt to end the session Trying 0.0.0.0 ...
    Any assistance or ideas offered will be greatly appreciated.
    Thanks,

    Hi Tabish,
    How many times do you have to open this same topic?
    In my opinion, this is your THIRD thread for the same topic.

  • Lenovo 3000 N500 23G Battery Status LED problem.

    I am having problems with the Battery Status LED on my new laptop.  The LED turns blue at around 22-30% charge and the Hardware manual indicates it should be 95%, also the LED remains lit when fully charged on battery power when it should be off. The biggest problem is that I have no idea on when the battery is charged and I should not need to boot into windows to check this.
    I have already returned an identical model to the retailer for the same reason, they did confirm that the unit was faulty and send me another which seems to have the same suspected fault.
    Has any one else have the same problem as me, I am not too sure if I should return the 2nd unit for a refund and look elsewhere?
    I did contact Lenovo support before and was advised to get it repaired under warranty, I did not need to do this as the unit is less than 30 days old and I wouldbe entitled to a refund or replacement.
    Below is an excerpt from the manual I downloaded from this website.
    Thanks, Mark.
    Blue: The battery is charged to 95% or more of its capacity.
    Blinking blue: The battery is being trickle-charged
    Orange: The battery is being normally charged
    Off: The computer is operating on battery power, and the battery has enough power
    Blinking orange: The computer is operating on battery power, and the battery is charged to no more than 8% of capacity.)

    The battery is going to fail on this unit; actually it is a defect in the circuit built into the battery the detects charge level.  It has been happening quite frequently with IBM/Lenovo batteries these days.  If you have warranty left, get the unit in for repair or you will be out of luck like the rest of us who bought these units with failure prone batteries and a poor excuse for product quality.  If you care to help your fellow Lenovo owners, call, email, write, picket, jump up and down, do what ever you have to do to voice your concern and complaint to as high a person as you can at IBM and Lenovo.  We have to keep the heat on at a corporate level at both IBM and Lenovo, to remind them that there is a price to pay for the fact that they do not care about their customers.   

Maybe you are looking for

  • Two config material in sales order?

    Hi All In variant Configuration , in sales order i created two line items with the same material , but the character values are diff. When i run the md04 it working fine with the item 10 , but for the item 20 no value related material has not been  p

  • How do I get back all the songs stored in iTunes after they were wiped out off my computer?

    How do I get back all the songs stored in iTunes after they were wiped out when I re-installed Windows 7?

  • Liquify tool photoshop cc 2014

    where can i find the liquify tool photoshop cc 2014? I  have looked everywhere!

  • Missing Plugin for Adobe Flash Player 10.1?

    I have an 64 bit acer computer Windows Explorer 7 XP I am using Mozilla Firefox When trying to download Flashplayer 10.1 I click to download but the information bar comes up saying Additional plug-ins required to display all media on this page. When

  • Urgent: User Exit Coding

    Need help in missing coding for the below: DATA : wa_var_range LIKE LINE OF i_t_var_range, wa_e_t_range TYPE LINE OF rsr_t_rangesid. When zmbpbrnd. If I_step =2 Clear wa_e_t_range. select * from zmbp_brand_auth where zmbp_de_brand= zmbpbrnd and xubna