D5503 touchscreen display loses pressing

Hello,
I have Xperia Z1 Compact Black D5503 for 5 days.
I like it, but i have a problem with touchscreen.
When i press the screen and start drawing or swiping something(continuous touch) - it randomly losses my touches.
For example in Xperia Diagnostic Tool i don't have one line when i drawing, i have two or three. Pulling down the notification bar doesn't always register and rolling my thumb on the screen to lazily scroll a webpage registers as a zoom. In sony launcher when i swype apps list left-right it sometimes run app instead of swiping.
It may happen 2-3 times for 10-seconds and may not happen even in 2 minutes. So i think it is randomly and occurs in any part of the screen rather than in a single point.
I don't have any touch screen protectors except sonys default. I have this bad touchscreen screen everywhere in the system, not only in some apps.
A also did reset to manufacter defaults in phone and in pc companion.
I have 2 Sony Xperia Z and i never had such bad touchscreen experience.
Is it software issue or something with hardware? Do i need to go to the service center?
D5503, latest 4.3 (.114), Dispaly type(manufacturer): auo, Touch firmware version: e.
I have a normal hands. ))

Hi and welcome to the community! Since you're new please be sure that you have checked out our Discussion guidelines.
I suggest that you try to reinstall the phone software using Update Service..
Before reinstalling your device you may want to backup your information first. Check out this topic for more information on how to.
How to backup?
If the issue should still remain I think that this needs to be examined and fixed at a repair center. For more information about how to submit your phone for repair and where, contact your local support team.
- Community Manager Sony Xperia Support Forum
If you're new to our forums make sure that you have read our Discussion guidelines.
If you want to get in touch with the local support team for your country please visit our contact page.

Similar Messages

P55W Adjusting sensitivity on touchscreen display to use stylus?

I recently bought a P55W-B5220 laptop and would like to be able to use a pen / stylus on the touchscreen display like a tablet. I'm not sure if I just have an incompatible stylus or if there is a sensitivity issue that is preventing me from utilizing the laptop in this way. I can use my fingers to manipulate the screen just fine. I only have problems when I try to use my stylus. Is there any way to ajdust teh sensitivity of the screen? Or do I need to try another design of stylus / pen? Thank you,Kay

Hi! I am also trying to reduce its sensitivity. In my case, if the brightness goes above 50%, I start getting hundreds of "touches" on the screen, becoming impossible to use. I keep my screen dim but sometimes I need full brightness or, when being outside/plugging it in to the ac. it shifts and goes crazy.

How to keep the watch to display without press the button on my iPod Nano 6th)?

Dear Guys,
I have purchased a watchband for my ipod nano 6th recently, overall is okay but i don't know how to keep the watch to display without pressing the sleep/resume button on edge? Also, the screen is not showing the watch immeditaly when I press the button, it shows the music/cd folder, then I need to scroll the screen back to the watch display. Please help.

There is no way to keep the display on permanently, as doing so would significantly reduce the overall life of the battery. It would maybe last only hour, maybe not even.
As for having your iPod wake up to the watch view, head to Settings -> General -> Time on Wake -> On.
B-rock

Touchscreen display monitor toggling

Hi All,
Bought an acer touchscreen monitor and hooked it up to my iMac. Its on extended display mode and when I touch the screen on the display It starts to control the mouse if its on the iMac's display. Is it possible to make the mouse jump to the other display when I touch to move it?
Thanks.
Olly.

Hi
In my knowledge such function is supported by several graphic cards.
You dont write anything about your notebook. Its not very helpfully
Anyway, I think you can change the screen position it in the graphic card properties.
Check the advanced options.
PS: I think you have accidentally enabled this option. As far as I can remember the on the Nvidia graphic cards you can use the key combination to change this rotation option:
Ctrl + Shift + R

Display loses brightness after restarts

I have a question that I can't seem to find the answer to. Since some update (can't remember which one), my MacBook Pro will lose it's brightness after restarting. But here's the funny part, it doesn't lose it "quickly" after a restart. For instance, I use cocktail to run at night. When my MacBook Pro restarts, the brightness is perfect. But... if I leave it at the login-screen (I use username/password to enter desktop), it eventually will turn off the brightness. I can't tell you how long after restart since I never timed it or saw it do it. It's just that every morning, my mac is sitting with no brightness on the login screen. Then I have to hit the brightness button.
Any suggestions? I've reset the NVRAM and reset the PRAM. I guess I should take it off the login and see if it dims the desktop after logging in after a restart.
Bryan

You might check "Options" under Energy Saver and see if the box is checked that says "Automatically reduce the brightness of the display before display sleep". I don't know if this is relevant, but you could uncheck it and see if it makes a difference.
Good luck!

There was a problem connecting to the server message - displayed when pressing printer email address

HP Photosmart B210, Windows 7...was able to print from iphone yesterday but now will not print. One the face of the printer if the ePrint symbol is pressed for the printer address the message "there was a problem connecting to the server" appears. I can find the device with my phone and on my computer. I can print from the computer but not phone

I understand you are getting unable to connect to server error message on your printer. I would first unplug router and printer for about 1 minute. I would plug router up first then printer. I would then try to enable web services. If not successful and you get same error message. I would follow these steps.
1. Obtain your printer's IP address
a. This can be done by pressing the wireless icon on printer.
2. Enter the printer's IP address in a browser.
3. Select the network tab at the top of the page.
4. On the left select networking.
5. Select Network Address (IP)
6. Select Manual DNS Server
a. Manual Preferred DNS should read 8.8.8.8
b. Alternate DNS Server should read. 8.8.4.4
7. Select apply you might get a warning just select okay.

Greek language notes display loses accented characters

I can type in Greek in TextEdit, save the file as Unicode (UTF-16), and drag it into my iPod Notes folder.
In OS10.4 I can use accented characters in TextEdit but, when the file is loaded onto the iPod, it omits the accented characters. They aren't displayed incorrectly - they simply aren't displayed at all.
Anyone ever tried uploading Greek to an iPod? Any Greek users out there?
Martin

Yes, the accented characters appear OK on my wife's video iPod.
I suppose there's no chance that Apple will update the software on my not-very-old color iPod?
No, I thought not. Money-grabbing *****s.
I love Apple but not ALL the time.

Touchscreen unresposive and pressing buttons on it's own

Hello,
I have the Xperia Z3 for three weeks now, and yesterday the touchscreen started to be unresponsive and doing things on its own. I have reset my phone and left it off for 12 hours but there is no difference in it's behavior. I also did the PC Companion Software repair but still no difference at all. Also I haven't dropped the phone a single time and it haven't touched any water at all. So if anyone have had the same experience I would gladly like to know what could be the problem.
With regards,
Connery M. A.

You should contact your local Xperia Care
http://www.sonymobile.com/global-en/support/contact-us/
"I'd rather be hated for who I am, than loved for who I am not." Kurt Cobain (1967-1994)

13"w/ext display loses WiFi connection after waking from sleep

I have my 13" macbook pro (mid-2009) connected to an external monitor. When the system goes to sleep and wakes up, the wifi is disconnected and an error window pops up saying something to the effect of another computer is using the IP address assigned to my computer.
If I reset the modem it usually works, otherwise I must wait about 15 minutes for system to connect again.
It does not happen if there is no monitor connected to the notebook.
Is there something I can do to stop this from happening?

I have a strong suspicion that I am getting wifi interference from my neighbors. Several new wifi signals have appeared in the last month coinciding with new neighbors moving in and some old ones getting wifi. Upstairs, I can pull up 6 or 7 networks, some broadcasting on the same channel. Downstairs, where my MacPro resides, I do not see those networks. My problem seems to manifest itself on my MacBook Pro when I move upstairs and can pick up the extra networks.
When I power cycled my router this morning, I noticed it changed channels from 11 to 6, indicating that the Auto setting is determining a better channel. Also, this problem seems worse after 5 pm. So, I'm chalking this one up to neighbor interference. If my iPhones could use the 5 GHz band, I'd use that exclusively... or maybe it's time for a simultaneous dual band router.
I wish I had a dollar for every time I've advised a customer that interference was the cause of his wireless connectivity issue.

TS1398 iPad mini with retina display loses WIFI connectivity quickly

I'Ve seen several posts about this including one where apple replaced a iPad.
I have recovered my pad and that fixed tethering and some other problems but WIFI is still a problem. It only stays connected for a few minutes. When I pick it up after it was asleep it looks connected but isn't. My iPhone 6 works perfectly after 8.0.02 but the iPad is still having probems. toggling the WIFI off and on sometimes works but I usually have to rest the pad to get it working. Thought it was my router till I found all my other Apple IOS devices woring just fine. What can I do?

This is the iPod touch forum

My Thunderbolt display has gone noticeably dim with the mis-press of a button.

I have a dual monitor set up with a brand new 15" MBP and Thunderbolt display. I was working on the Thunderbolt display and pressed a key and now my screen is noticeably dimmer, even though brightness settings are all the way up. Once I unplug the display from my MBP, the MBP takes on the settings and becomes noticeably dimmer regardless of the brightness settings turned up. I'm unsure as to how to fix this. Any tips on what I can do or mistakes I may have made?
Thanks.

After a few reboots of my Mac, reconnects to the display, and restarts of iTunes, the problem seems to be gone. I am unable to reproduce it now. So, yay! But for a while I was quite concerned. I haven't the slightest idea what was causing this problem, but there were many factors at play. Like playing to multiple sources in iTunes, equalizer settings, etc. I jut simply don't know enough about the technology.

Prompt command misdisplay, 2 letters constantly displayed b4 command

I run Arch Linux in VirtualBox.
I use bash history. On first click a _long_ command is displayed. On next clicks, the first 2 characters of the _long_ command are constantly displayed on the screen followed by the next command in turn. If I press "enter" the new command is normally executed without considering the first 2 characters. They disappear by "enter" or "clear" and come back again after the execution of another _long_ command.
e.g.
# > pwd
# > time
# > date
# > date (time, pwd) (are displayed by pressing the upwards arrow)
# > less /.../.../.../file (first long command)
# > ledate (letime, lepwd) (are displayed by the upwards arrow)
Any idea what I have done wrong?
Thanks
PS: bash.bashrc.local
# This file is in the public domain.
# It's created by ...
echo
echo -e "\e[35;40;1m##############################################################################"
echo -e "\e[35;40;1m#@@@ @@@#"
echo -e "\e[35;40;1m#@@ \e[36;40;1mArch GNU/Linux!\e[35;40;1m @@#"
echo -e "\e[35;40;1m#@ @#"
echo -e "\e[35;40;1m#@@ \e[32;40;1mIt puts the fun back into computing.\e[35;40;1m @@#"
echo -e "\e[35;40;1m#@@@ @@@#"
echo -e "\e[35;40;1m##############################################################################"
# Check for an interactive session
[ -z "$PS1" ] && return
PS1='\n\[\e[30;40;1m\]\016l\017-[\[\e[36;40m\]\s\[\e[30;40;1m\]]-[\[\e[37;40m\]\u@\H\[\e[30;40;1m\]]-[\[\e[32;40m\]\l\[\e[30;40;1m\](\[\e[31;40m\]\j\[\e[30;40;1m\])]-[\[\e[33;40m\]\@ \d\[\e[30;40;1m\]]-(CmdNo.\[\e[31;40m\]\!\[\e[30;40;1m\])-(HistNo.\[\e[31;40m\]\#\[\e[30;40;1m\])\n\[\e[30;40;1m\]\016t\017-[\[\e[34;40;1m\]$(pwd)\[\e[30;40;1m\]]-(\[\e[34;40m\]$(ls-t | wc -l) files,$(ls-l | grep -m 1 total | sed {s/total//})b\[\e[30;40;1m\])\n\016m\017-> \[\e[35;40m\]\$\[\e[37;40m\] > '
PS2='\[\e[31;40m\]more!\[\e[37;40m\] > '
PS3='\[\e[31;40m\]Select\[\e[37;40m\]> '
PS4='\[\e[31;40m\]debug\[\e[37;40m\] > '

I do not have a backup. Should I back up before I try doing a reinstall of the os x?
That's also known as shutting the barn door after the horse has bolted.
It can't hurt, but it's not going to help much.
Camelot: when you say "apps and user content should stay intact" - doesn't sound very definitive. Are there any variables that come into play?
No.. generally it's pretty reliable, but yours is an odd situation. I wouldn't expect to lose any user data, just CYA
I do have a start up disk along with some apps that I created in retrospect many years ago ....(I think it's os x 10.2.8) Can I use this to boot up and then just navigate to my user files so I can get some things done that I need to?
Unlikely. For one have you even tried restoring from your Retrospect backup? (it's not the most reliable system).
Secondly, you can't boot from your Retrospect backup, so you'll need to restore that system to boot from it. Have you got a second disk to restore to (you do NOT want to restore 10.2.x over your 10.4.x system).
in terms of "random deleted files" : not entirely random
Ok, maybe not entire random, but it's also somewhat unknown. You need to have some idea of what files you're trying to restore, but if you haven't got them in a backup where are you going to get them from?
You cannot just take old copies from your 10.2.x system and hope they'll work (in case that's what you're thinking).
The BEST solution is to boot from the 10.4.x installer disk and let it do its thing.
And for what its worth, Unauthorized access attempts, in and of themselves, are not a cause for concern since they were clearly caught by the OS. It's the access attempts that succeed (and are not logged) which are more of an issue.

[X230] Missing on-screen display in W7

Hello, I have foolishly uninstalled "On Screen Display" from Programs & Features, thinking it was some kind of junk/malware stuff. This caused me to lose the brightness/volume on-screen display. Duh! I tried to follow earlier instructions on how to bring it back... I installed Lenovo Power Management which brought the "On Screen Display" application back, or at least it is showing under Programs & Features again, but after rebooting, I still don't have on-screen display when pressing volume or brightness keys. What else can I do to bring it back? This is under W7 Home 64-bit. Thanks!

Solution is here.
To summarize what he did:
1. Install all available drivers for your ThinkPad X201 using support.lenovo.com or ThinkVantage System Update
2. Re(install) the fingerprint reader driver
3. After the fingerprint reader driver is installed, reinstall Hotkey Features Integration.
Jonas
Microsoft MVP: Windows Consumer Expert
Yoga Tablet 2 10 || ThinkPad X1 Carbon (20A7007MPH) || ThinkPad Helix (3698-6EU) || IdeaCentre B540
Twitter: @jonashendrickx

How do i use my imac 21.5" 2011 as a display for my macbook pro late 2011, through thunderbolt cable ? I have tried and it doesnt seem to work, neither does target disk mode.

How do i use my imac 21.5" 2011 as a display for my macbook pro late 2011, through thunderbolt cable ? I have tried and it doesnt seem to work, neither does target disk mode.
Could it be a borked cable ? I just bought it new from the store today, i have updated both imac and macbook pro to latest thunderbolt firmware and updates. Both 10.7.3.
MacBook Pro:
Vendor Name:    Apple, Inc.
Device Name:    MacBook Pro
UID:    0x0001000A17016E60
Firmware Version:    22,1
Port:
Status:    No devices connected
Link Status:    7
Port Micro Firmware Version:    FFFF.FF.FF

You are correct, here is what Apple Says:
http://support.apple.com/kb/TS3775
I was able to find these instructions, however they referr to 2009-2011 27" iMacs. I think it's the same, if it's not then contact Apple directly for instructions. If either of the machines is less than 90 days old or covered by AppleCare then call AppleCare tomorrow for help, they should be able to easily answer this for you. You will find the number in your manual or you can use the AppleCare Contact Info link.
Your iMac should automatically recognize the presence of a digital video signal at the Mini DisplayPort and enter Target Display Mode.
If your iMac does not automatically enter Target Display Mode, press command + F2 to manually enter Target Display Mode.

Blank screen after rotating the display in Yosemite (MacBook Pro Late 2013)

Hi,
after installing Yosemite on my MacBook Pro 15" Late 2013 I have trouble rotating it's screen. After I launch Preferences and click Displays while pressing alt and command keys I see the list of possible orientations available.
If I now select 270° the screen immediately goes black. To be clear: The display is not turned off like when the MacBook sleeps. It's still lit, but only shows a black screen. After turning the MacBook off by pressing and holding the power button I can boot and voilà, the screen is perfectly normal, showing everything rotated at 270°. If I reset to Landscape from there (i. e. 0°), I have no problem at all, everything still works. Setting it back to 270° again lets the screen go black again.
I have an installation of Mavericks at my primary partition and it has no problems at all with rotation. Is this a known bug or can anyone confirm this behaviour?
As a hint for others suffering the same problem: You can get around the hard reset by pressing shift-comand-q followed by enter key. This logs your user out of the system and gets you back to the login screen. This obviously kind of reinitializes the UI. After that, the display's rotation is working and you just have to login again.
Even if this is some kind of workaround it would still be much more convenient not requiring this workaround.
Thanks in advance,
Oliver

Hi,
yes, I had the same issues here! My solution was to force the system to use the discrete graphics card instead of the intel one. Then you get some additional options for the resolution which are much more usable. If you need further infos let me know. I'm using the MacBook in a rotated state about 95% of the time and it works pretty well now (at least in Mavericks, where I also experience your described behaviour).
Greetings,
Oliver

D5503 touchscreen display loses pressing

Similar Messages

Maybe you are looking for