DAC cable between HP Flex-10 and Cisco 4900M
We have HP C7000/VC-Flex 10 Module that I would like to connect to our Netapps NFS datastore. The Cisco switch that I will be using between HP Flex-10 and Netapps is Cisco 4900M. I have a HP cable AP784A direct attach copper SFP+ to SFP+. Which module I need to purchase and insert into my 4900M to support 10Gb connectivity via HP DAC 10Gb cable.
Please Advise!
You need
4900M 4 port 10GE half card with X2 interfaces (WS-X4904-10GE)
OR
4900M 8 port 10GE half card with X2 interfaces (WS-X4908-10GE)
WITH
Cisco OneX Converter Module Converts an X2 Interface into One SFP+ Interface (CVR-X2-SFP10G)
I would recommend you to use following DAC cables from Cisco.
• SFP-H10GB-CU1M: 10GBASE-CU SFP+ Cable 1 meter (Version -02)
• SFP-H10GB-CU3M: 10GBASE-CU SFP+ Cable 3 meter (Version -02)
• SFP-H10GB-CU5M: 10GBASE-CU SFP+ Cable 5 meter (Version -02)
Similar Messages
-
The cable between the logic board and the 3G board was removed can I convert it to a Wifi only?
I have a Ipad 2 3g. someone detached the cable between the logic board and the 3G board can I convert it to a Wifi only?
The ipads that have 3g have an extra section attached to the logic board by a glued on wire. I bought this at a tag sale. Someone was apparently trying to repair their iPad and they did not know that when you removed that glued strip attaching the 3g antenna to the logic board you would never be able to re-atach it again later. So basicaly my 3g logic board is now in two pieces. the main logic board with wifi and the cdma 3g antenna. Now their is no differnce between the logic boards in either wifi only or wifi and 3g devices. I attempted to restore the device with the ios for wifi only, because there are 3 different ios versions depending on if you have wifi only wifi 3g with SIM card, or wifi 3g cdma.
-
Uplink between Stacked Dell 8132 and Cisco 1921 HSRP pair.
Hello,
I have three Dell 8132 switches stacked and we plan on connecting them to an HSRP pair of Cisco 1921 routers. What would be the best way to uplink these stacked switches to the 1921 pair?
I was thinking of creating vlan trunk from 2 of the 3 Dell switches, one trunk going to each router and enable HSRP on these trunks for the vlans I need to route. Would that be a good approach?
Attached is a basic network of what it would look like. Please suggest if this is a good way to accomplish this or if there is a more better and efficient way to do it?
ThanksJust to clarify I wasn't suggesting that you move all the routing to the Dell switches. If the routers are already doing some routing for you then you could simply connect the Dell switches with L3 uplinks.
But yes if you feel more comfortable using Cisco then use the routers.
I have never used an integrated switch module to be honest, I just used L3 switches and routers separately.
I suspect it would work as long as there was a backplane connection between the switch module and the router itself so you could route directly from the switch module to the router.
Can't say for sure whether there is or not as like I say I have never used them.
Which to use really comes down to how much bandwidth you need between vlans which only you know really. If you think using one interface and splitting it up may cause problems then you could look at a switch module.
Although it does seem a bit redundant purchasing a switch module when you have L3 switches already :-)
But I do understand what you mean about being a Cisco shop.
Jon -
SIP trunking between Microsoft OCS server and Cisco Voice GW router.
Hello All,
I have a client with an existing Microsoft OCS (office communications server) environment with the OCS server in their head office. The OCS clients in the remote Office registers with the OCS server in the head office. The WAN connectivity between the remote office and the Head office is MPLS.I would like to facilitate local call (PSTN) features at the remote site through a newly proposed Voice gateway router.
Can I achieve this by doing a SIP trunk between the OCS server in the head office to the newly proposed voice GW router in the remote office through the existing MPLS link. If yes, Could any one please assist me in this regards or suggest any other best solution to achieve the same.
Thank you in advance,
Mohammed Ameen RHi David,
this is a normal behaviour. To CUCM, OCS is a remote destination (just like your mobile phone). When your mobile phone hangs up, the system will put the call on hold for 10 sec.
This is there for the mobile user to go to his desk to pick up the call and continue the conversation (part of single number reach feature)
The best practise will be for the user to ensure that the other party hangs up the call first before he hang up.
Please grade if you think it's useful =) -
Dial-up connection between Asterik SIP server and Cisco 5400
Hi,
We have a setup for dial-up. The incoming call lands on Cisco 5400 and is forward to PGW using mgcp intergration. PGW sends it to Asterik SIP server over SIP. This Asterik Server sends it to another Cisco 5400 over SIP for Internet.
The issue is for some dial-up user, it works fine. But for some it doesn't. The problem is when we see the log on the last Cisco 5400, the incoming call tone is detected as FAX tone rather then Modem tone.
Any idea why is it so??Hi,
We have a setup for dial-up. The incoming call lands on Cisco 5400 and is forward to PGW using mgcp intergration. PGW sends it to Asterik SIP server over SIP. This Asterik Server sends it to another Cisco 5400 over SIP for Internet.
The issue is for some dial-up user, it works fine. But for some it doesn't. The problem is when we see the log on the last Cisco 5400, the incoming call tone is detected as FAX tone rather then Modem tone.
Any idea why is it so?? -
IPSEC between Netscreen SSG-140 and Cisco 3640 Router
The symptoms are that the NS will try to build the IKE session and time out. Even with the Cisco debugging enabled I get no IKE nor IPSEC SA trying to build on the 3640. What am I doing wrong or what can I try?
Enclosed is the configuration and a brief description of my environment.
172.30.0.0/16 -> 172.30.20.254 | Netscreen SSG-140 | 192.168.1.254 -> private net -> 192.168.3.5 | 3640 | 172.20.0.220 -> 172.20.0.0/16
The configurations are enclosedHi
I think you need to apply the crypto map to the interface FastEthernet0/0.
crypto map nsmap
Please rate if this helps.
Regards MJ -
Connectivity Issue between ASA 5520 firewall and Cisco Call Manager
Recently i have installed ASA 5520 firewall, Below is the detail for my network
ASA 5520 inside ip: 10.12.10.2/24
Cisco Switch 3560 IP: 10.12.10.1/24 for Data and 10.12.110.2/24 for Voice
Cisco Call Manager 3825 IP: 10.12.110.2/24
The users and the IP phone are getting IP from the DHCP server which configured on cisco 3560 Switch.
the Default Gateway for Data user is 10.12.10.2/24 and
for the voice users is 10.12.110.2/24
now the problem is that the users is not able to ping 10.12.110.2 call manager. please if somebody can help in this regard. i will appreciate the prompt response against this issues.Actually i don't wana to insert new subnet and complicate the nework. i need a simple way to solve the problem. below is the details for the asa 5520 config.
ASA Version 8.2(1)
name x.x.x.x Mobily
interface GigabitEthernet0/0
nameif inside
security-level 99
ip address 10.12.10.2 255.255.255.0
interface GigabitEthernet0/1
nameif outside
security-level 0
ip address x.x.x.x 255.255.255.252
object-group service DM_INLINE_SERVICE_1
service-object tcp-udp
service-object ip
service-object icmp
service-object udp
service-object tcp eq ftp
service-object tcp eq www
service-object tcp eq https
service-object tcp eq ssh
service-object tcp eq telnet
access-list RA_VPN_splitTunnelAcl_1 standard permit Inside-Network 255.255.255.0
access-list RA_VPN_splitTunnelAcl standard permit Inside-Network 255.255.255.0
access-list inside_nat0_outbound extended permit ip Inside-Network 255.255.255.0 10.12.10.16 255.255.255.240
access-list inside_nat0_outbound extended permit object-group DM_INLINE_SERVICE_1 10.12.10.16 255.255.255.240 Inside-Network 255.255.255.0
access-list inside_nat0_outbound_1 extended permit ip Inside-Network 255.255.255.0 10.12.10.16 255.255.255.240
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
mtu mgmt 1500
ip local pool VPN-Pool 172.16.1.1-172.16.1.30 mask 255.255.255.0
ip local pool VPN-Users 10.12.10.21-10.12.10.30 mask 255.255.255.0
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-641.bin
asdm history enable
arp timeout 14400
global (inside) 2 interface
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound_1
nat (inside) 1 Inside-Network 255.255.255.0
route outside 0.0.0.0 0.0.0.0 Mobily 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http Mgmt-Network 255.255.255.0 mgmt
http Inside-Network 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 30
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
telnet Inside-Network 255.255.255.0 inside
telnet timeout 5
ssh Inside-Network 255.255.255.255 inside
<--- More ---> ssh timeout 5
console timeout 0
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy RA_VPN internal
group-policy RA_VPN attributes
dns-server value 86.51.34.17 8.8.8.8
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value RA_VPN_splitTunnelAcl
username admin password LPtK/u1LnvHTA2vO encrypted privilege 15
tunnel-group RA_VPN type remote-access
tunnel-group RA_VPN general-attributes
address-pool VPN-Users
default-group-policy RA_VPN
tunnel-group RA_VPN ipsec-attributes
pre-shared-key *
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
service-policy global_policy global
prompt hostname context
Cryptochecksum:e5a64fa92ae465cd7dabd01ce605307d
: end -
SCSI cable between the DAT 72 and V440?
Hi all there,
What SCSI cable type do I need to connect the DAT 72 tape drives and the V440 servers? I haven't found any information in the whole sun webpage.
Thanks in advance,
Luis Rubio530-2383 should do the job.
-
IPSEC Tunnel between JUNIPER (SSG 20) and CISCO PIX 501
I have successfully established the IPSEC tunnel with juniper firewall by using cisco Pix 501 (6.3 version). The problem I am facing, I have network layer connectivity but after time interval I am not able to send the traffic on destination IP address on specific port, but can successfully PING the destination IP. On both firewalls the IPs are permitted for all ports.
Dear Mr.
The same problem has occured with me. -
HP DAC Copper Cable with Cisco 4900M
We have HP C7000/VC-Flex 10 Module that I would like to connect to our Netapps NFS datastore. The Cisco switch that I will be using between HP Flex-10 and Netapps is Cisco 4900M. I have a HP cable AP784A direct attach copper SFP+ to SFP+. Which module I need to purchase and insert into my 4900M to support 10Gb connectivity via HP DAC 10Gb cable.
Please Advise!You need
4900M 4 port 10GE half card with X2 interfaces (WS-X4904-10GE)
OR
4900M 8 port 10GE half card with X2 interfaces (WS-X4908-10GE)
WITH
Cisco OneX Converter Module Converts an X2 Interface into One SFP+ Interface (CVR-X2-SFP10G)
I would recommend you to use following DAC cables from Cisco.
• SFP-H10GB-CU1M: 10GBASE-CU SFP+ Cable 1 meter (Version -02)
• SFP-H10GB-CU3M: 10GBASE-CU SFP+ Cable 3 meter (Version -02)
• SFP-H10GB-CU5M: 10GBASE-CU SFP+ Cable 5 meter (Version -02) -
The maximum cable distance from antenna and Cisco 1200 series.
Hello all!
I?m using the Cisco 1200 Access Points Series with two 2.2dBi dipole antennas. I have read the installation guide for that Access Points and that can be installed with the antennas in separated places. But this guide didn't mention the maximum distance for the antenna cable...
Somebody here can say me this maximum distance?
Had somebody here made this kind of antenna installation with cable?
Thanks.Oh Yeah!, I absolutely agree on "shorter is way better"
Given any chance / choice at all, I'd try to keep the cable length under 25 feet. If the option is available for a NEMA cabinet to get the cable shorter, I'd probably do that too.
Since it's good practice to use a chunk of fiber optic cabling between the external stuff and the inside network, you may as well put the AP as close to the antennas as possible and convert the copper to fiber for the long haul.
You get some lightning protection (at least you won't smoke all of the systems sitting on your LAN) and better signal strength (and probably signal quality too).
For something like a 200' run, if forced to do it (we're talking "gun to the head" forced here), I'd probably be looking for something like Andrew LDF4-50 1/2" Heliax with probably a weeeeee bit O' amp tossed in for good measure.
That would also imply that the system would also have to be re-certified, because of the non-standard components ...and a pretty good budget to boot.
Sometimes you gotta do what you gotta do.
FWIW
Scott -
Hello, I couldn't find this on the Cisco Flex 7500 specs
http://www.cisco.com/en/US/partner/prod/collateral/wireless/ps6302/ps8322/ps11635/data_sheet_c78-650053.html
Do anybody know if I can set up an anchor mobility group between the Flex 7500 and the WLC 5508?
Kind regardsYes, 5508 can be used as anchor controller for static anchoring while 7500 as foreign using central swtiching.
For Mobility:
Fault Tolerance
It is recommended to use Flex 7500 as both the primary and backup controllers.
Flex 7500 primary and backup controllers must be in the same mobility domain.
Ref:
http://www.cisco.com/en/US/products/ps11635/products_tech_note09186a0080b7f141.shtml -
I installed the cable between my TV set and the new apple Tv for streaming. Nothing cam up on my TV screen. I want to get NETFLIx from my apple tablet and myTv set.
Change to the appropriate input on the tv.
-
Cable Between Physical Input and Seq. Input Disappears By Itself
Today, inexplicably, while recording routine MIDI overdubs on a cue, I suddenly lost MIDI thru from my master keyboard thru Logic to my MIDI racks. MIDI tracks played fine, but no MIDI thruput.
Tested the MIDI interfaces, AMS, rebooted the computer and the interfaces, all the usual stuff. Couldn't find any reason why I suddenly lost thruput.
It was only because I was at my wit's end that I decided to look at the Clicks and Ports Layer in the Environment to see if anything "somehow" got weird. And sure enough... the cable between the Physical Input and the Sequencer Input had disappeared. Gone. Vanished. Deleted.
How this could have happened without my deliberately going into the Environment, selecting the Clicks and Ports Layer and purposely deleting the cable connection is totally beyond me. This has got to be one of the weirdest behaviors I've seen. And just remember everyone, "weird" is an anagram for "wired" which, unfortunately, proved not to be the case.
Anyone else ever have this happen? Any ideas as to what might have caused this?Amin,
I've thought along these lines too, surmising that: items (or data) which were selected/highlighted in various windows at various times were somehow still subject to such actions as Delete, Cut, or Clear, despite the fact that those windows were currently closed. Now, I rarely (closer to "never") have need to visit the Clicks/Ports layer of the Environment, let alone tinker with the connection between phys input and seq input such that that cable might ever remain in a "selected" or "highlighted" state to begin with.
But in an effort to troubleshoot the missing cable scenario according to this theory, I deliberately highlighted the cable, closed that window, and continued working. I was hoping that at some point during normal editing operations I might lose my MIDI thruput again (because it got cut/deleted/cleared in association with a cut/delete/clear operation of another event or object) and then backtrack through the Undo History hoping to discover what operation caused it.
Well, 1.5 days later, after intensive editing of the same sequence (which ended up becoming quite complex) the cable stayed intact! So to a certain extent I think perhaps my theory is wrong, but I'm keeping an open mind.
But something valuable came out of this... considering LPH/David's information, I think that from now on I'm going to eliminate the physical input and sequencer input objects from my environment; they've proven to be a liability. And it's easy enough to add them to a song in the event I want to do some MIDI processing on Logic's input side.
I'd like to respond to your thoughts on floating windows in a separate post.
Cheers Amin! -
Difference between CIVS-IPC-VT38 and CIVS-IPC-VF31
Hi Expert,
1, May I know difference between CIVS-IPC-VT38 and Cisco IP Camera Fujinon 3-8 mm Varifocal Lens CIVS-IPC-VF31?
2, Do I need a lenses for Cisco CIVS-IPC-2611 Dome camera, if it is what the part number?
ThanksI'm just going by memory here, but I believe the VT38 part is made by Tamron, and the VF31 part is made by Fujinon.
Personally, I prefer the Tamron parts if I have the option, but you may want to review the detailed spec sheets from each manufacturer.
Also, the 2600 series domes have their *own* non-swapable optics made by "Computar". I can't remember the varifocal range off the top of my head right now, but it would be in the datasheets from Cisco for sure.
Hope this helps!
Cheers!
Maybe you are looking for
-
Is the original IPad still able to be updated?
-
Where can I control Auto Save and Versions? I can't find it in System Settings. Can I control it by terminal commands? On http://www.apple.com/macosx/what-is/ Apple claims: Versions creates a new version of a document each time you open it and every
-
Seagate drives not compatible with Time Machine causing OS lag/hangs?
Setup- Intel iMac (Early 2006) Mac OS X 10.5.1 Seagate FreeAgent Pro 750GB External Drive Reproducible Issues MacOS X lags at start up with the Seagate drive connected via Firewire and Time Machine enabled. MacOS X hangs at shutdown with the Seagate
-
E63 doesn't detect my Netgear Router (wgr614 v6)
E63 does not detect my netgear router (wgr614 v6). My T-Mobile SDA and T-Mobile Shadow, can detect it easily and also connect successfully. Here are the settings I have on router: Security: WEP Auth: Automatic Encrypt: 64 bit Channel: 6 Mode: g and b
-
Hello: I have an XL-2 and recently used it to video a sheep dog trial. I shot the video on Auto and brought it into Final Cut Pro 5.12. Then I exported it to the web using Sorenson Squeeze as a QT file. I am finding that as in the past, the contrast