DAG Configuration Question

Hey guys
I have 3 Exchange 2013 servers in one site and 3 in another. I currently have them tied into one large DAG and keep a primary plus 2 copies of each database within my DAG. My question is, is this a valid configuration - to have a DAG that doesn't
necessarily hold a database copy?
Cheers,
Joe

So I have six nodes in the DAG but for each database only three copies (including my primary), therefore there are 3 remaining nodes that are participating in my DAG without a copy for that database. I suppose my question is: is this valid or should I be
creating a DAG specifically for each database and copy relationship (no idle nodes). I think the way I have it set up now is fine, I just wanted to make sure I wasn't going against best practice.

Similar Messages

SAP-JEE, SAP_BUILDT, and SAP_JTECHS and Dev Configuration questions

Hi experts,
I am configuring NWDI for our environment and have a few questions that I'm trying to get my arms around.
I've read we need to check-in SAP-JEE, SAP_BUILDT, and SAP_JTECHS as required components, but I'm confused on the whole check-in vs. import thing.
I placed the 3 files in the correct OS directory and checked them in via the check-in tab on CMS.   Next, the files show up in the import queue for the DEV tab. My questions are what do I do next?
1. Do I import them into DEV? If so, what is this actually doing? Is it importing into the actual runtime system (i.e. DEV checkbox and parameters as defined in the landscape configurator for this track)? Or is just importing the file into the DEV buildspace of NWDI system?
2. Same question goes for the Consolidation tab.    Do I import them in here as well?
3. Do I need to import them into the QA and Prod systems too? Or do I remove them from the queue?
Development Configuration questions ***
4. When I download the development configuration, I can select DEV or CON workspace. What is the difference? Does DEV point to the sandbox (or central development) runtime system and CONS points to the configuration runtime system as defined in the landscape configurator? Or is this the DEV an CON workspace/buildspace of the NWDI sytem.
5. Does the selection here dictate the starting point for the development? What is an example scenarios when I would choose DEV vs. CON?
6. I have heard about the concept of a maintenance track and a development track. What is the difference and how do they differ from a setup perspective?   When would a Developer pick one over the over?
Thanks for any advice
-Dave

Hi David,
"Check-In" makes SCA known to CMS, "import" will import the content of the SCAs into CBS/DTR.
1. Yes. For these three SCAs specifically (they only contain buildarchives, no sources, no deployarchives) the build archives are imported into the dev buildspace on CBS. If the SCAs contain deployarchives and you have a runtime system configured for the dev system then those deployarchives should get deployed onto the runtime system.
2. Have you seen /people/marion.schlotte/blog/2006/03/30/best-practices-for-nwdi-track-design-for-ongoing-development ? Sooner or later you will want to.
3. Should be answered indirectly.
4. Dev/Cons correspond to the Dev/Consolidation system in CMS. For each developed SC you have 2 systems with 2 workspaces in DTR for each (inactive/active)
5. You should use dev. I would only use cons for corrections if they can't be done in dev and transported. Note that you will get conflicts in DTR if you do parallel changes in dev and cons.
6. See link in No.2 ?
Regards,
Marc

Configuration question on css11506

Hi
One of our vip with 4 local servers, currently has https. the http is redirected to https.
Now, my client has problem which a seriel directories need use http, not https. some thing like. quistion:
     1. If there is any possible, I can configure the vip to filter the special directories and let them to use http not https. and rest pages and directories redirect to https?
     2. If not, I can make another vip to use same local servers, but, is possible to only limited to special directories? and with wild code? some like the directories are partially wild coded, something like, http://web.domain/casedir*/casenumber?
     3. if not on both option, is any way I can fix this problem?
Any comments will be appreciated
Thanks in advance
Julie

I run my Tangosol cluster with 12 nodes on 3
machines(each machine with 4 cache server nodes). I
have 2 important configuration questions. Appreciate
if you can answer them ASAP.
- My requirement is that I need only 10000 objects to
be in cluster so that the resources can be freed upon
when other caches are loaded. I configured the
<high-units> to be 10000 but I am not sure if this is
per node or for the whole cluster. I see that the
total number of objects in the cluster goes till
15800 objects even when I configured for the 10K as
high-units (there is some free memory on servers in
this case). Can you please explain this?
It is per backing map, which is practically per node in case of distributed caches.
- Is there an easy way to know the memory stats of
the cluster? The memory command on the cluster
doesn't seem to be giving me the correct stats. Is
there any other utility that I can use?
Yes, you can get this and quite a number of other information via JMX. Please check this wiki page for more information.
I started all the nodes with the same configuration
as below. Can you please answer the above questions
ASAP?
<distributed-scheme>
<scheme-name>TestScheme</scheme-name>
<service-name>DistributedCache</service-name>
<backing-map-scheme>
<local-scheme>
<high-units>10000</high-units>
<eviction-policy>LRU</eviction-policy>
<expiry-delay>1d</expiry-delay>
<flush-delay>1h</flush-delay>
</local-scheme>
</backing-map-scheme>
</distributed-scheme>
Thanks
RaviBest regards,
Robert

Configuration Question on local-scheme and high-units

I run my Tangosol cluster with 12 nodes on 3 machines(each machine with 4 cache server nodes). I have 2 important configuration questions. Appreciate if you can answer them ASAP.
- My requirement is that I need only 10000 objects to be in cluster so that the resources can be freed upon when other caches are loaded. I configured the <high-units> to be 10000 but I am not sure if this is per node or for the whole cluster. I see that the total number of objects in the cluster goes till 15800 objects even when I configured for the 10K as high-units (there is some free memory on servers in this case). Can you please explain this?
- Is there an easy way to know the memory stats of the cluster? The memory command on the cluster doesn't seem to be giving me the correct stats. Is there any other utility that I can use?
I started all the nodes with the same configuration as below. Can you please answer the above questions ASAP?
<distributed-scheme>
<scheme-name>TestScheme</scheme-name>
<service-name>DistributedCache</service-name>
<backing-map-scheme>
<local-scheme>
<high-units>10000</high-units>
<eviction-policy>LRU</eviction-policy>
<expiry-delay>1d</expiry-delay>
<flush-delay>1h</flush-delay>
</local-scheme>
</backing-map-scheme>
</distributed-scheme>
Thanks
Ravi

I run my Tangosol cluster with 12 nodes on 3
machines(each machine with 4 cache server nodes). I
have 2 important configuration questions. Appreciate
if you can answer them ASAP.
- My requirement is that I need only 10000 objects to
be in cluster so that the resources can be freed upon
when other caches are loaded. I configured the
<high-units> to be 10000 but I am not sure if this is
per node or for the whole cluster. I see that the
total number of objects in the cluster goes till
15800 objects even when I configured for the 10K as
high-units (there is some free memory on servers in
this case). Can you please explain this?
It is per backing map, which is practically per node in case of distributed caches.
- Is there an easy way to know the memory stats of
the cluster? The memory command on the cluster
doesn't seem to be giving me the correct stats. Is
there any other utility that I can use?
Yes, you can get this and quite a number of other information via JMX. Please check this wiki page for more information.
I started all the nodes with the same configuration
as below. Can you please answer the above questions
ASAP?
<distributed-scheme>
<scheme-name>TestScheme</scheme-name>
<service-name>DistributedCache</service-name>
<backing-map-scheme>
<local-scheme>
<high-units>10000</high-units>
<eviction-policy>LRU</eviction-policy>
<expiry-delay>1d</expiry-delay>
<flush-delay>1h</flush-delay>
</local-scheme>
</backing-map-scheme>
</distributed-scheme>
Thanks
RaviBest regards,
Robert

Two node - Two site Active/Active DAG Configuration

Information
Both sites exist in a single AD domain
Site A
1 Exchange 2013 multi-role server (CAS + MBX)
Server will contain mailboxes for individuals who work in Site A
Server will contain database copies of databases in Site B
Site B
1 Exchange 2013 multi-role server (CAS + MBX)
Server will contain mailboxes for individuals who work in Site B
Server will contain database copies of databases in Site A
Goal
To create a configuration where users who work in Site A have their mailboxes active in Site A and users who work in Site B have their mailboxes active in Site B.
Questions
Since this DAG has an even number of members, where do I place the witness server? Do I need two witness servers, one in each site?
It seems to me as long as both sites can still communicate, I only need one witness server to maintain quorum.
To my current understanding, if Site A has a witness server, and Site A looses its WAN connection, Site B's databases are going to go offline because it has lost quorum.
I'm assuming if I placed a witness server in each site, and one of the sites lost its WAN connection, then I'd be placed in a split-brain scenario as both sites would still think it had quorum. Is this accurate?
The company has given me a limited budget hence the reason for only having two exchange servers in this setup. Is my only recourse to have four nodes (two nodes per DAG) in this active\active scenario? If the company says they absolutely cannot spend money
on two more servers, could I use the current setup in an active\passive configuration?
Thanks!

You would need to place the File Share Witness in a 3rd datacenter for automatic failover, otherwise depending which DC the FSW is ( and you can only have one FSW per DAG active a time), then in case of a WAN or DC failure, the databases will be active in
the DC that has quorum.
If the FSW is in Site A and Site A goes down, then quorum is lost and Site B will need to be manually swithed over using this procedure:
http://technet.microsoft.com/en-us/library/dd351049(v=exchg.150).aspx
To be truly active/active in both DCs, then you would need to 2 DAGs with each respective FSW in each DC that has the preferred user base.
Twitter!: Please Note: My Posts are provided “AS IS” without warranty of any kind, either expressed or implied.

DAG configuration in DR site

Planning for Exchange 2013 DR. I have some queries on configuring DAG in my DR site.
Current setup:-
Primary site:- (2MB,2 CAS)
DR Planning:-
One Mailbox,One CAS Server
In primary mailbox server, two nic card is there. One is for MAPI and other one is for DAG replication. In DAG replication NIC card there is no gateway. Primary site DAG working without
any issues. In DR mailbox server two nic is there(One for Mapi and other for DAG replication). Problem iam facing is Primary site DAG NIC card not able to communicate with DR MBX server, since there is no gateway in replication NIC card. If I add the gateway
in replication NIC, then it is communicating with DR MBX. But iam getting mutiple gateways warning message.
MY Query is:-
1) Is there any problem having multiple gateways in MBX server.
2) If there is no problem with multiple gateway, how to restrict the users traffic hitting DAG replication NIC card.
3) Is there any configuration required in failover cluster manger menu for DR.
4) Is there any way to check DAG(replication) traffic hitting which NIC card..
Thanks for your support...

Hi vino,
Thank you for your question.
Replication networks typically do not have default gateways, and if the MAPI network has a default gateway, then no other networks should have default gateways. Routing of network traffic on a Replication network can be configured by using persistent, static
routes to the corresponding network on other DAG members using gateway addresses that have the ability to route between the Replication networks. All other traffic not matching this route will be handled by the default gateway that's configured on the adapter
for the MAPI network.
So we should check configuration which is DAG cross site, we could refer to the following link:
https://social.technet.microsoft.com/Forums/exchange/en-US/bc260c97-a5aa-484d-bc8a-e7660ef4554f/setup-exchange-2010-dag-across-sites?forum=exchange2010
Issue 1: NO
Issue 2: In a general, user network was separated with replication network.
Issue 3:NO
Issue 4:it is pre-defined by yourselves, we could defined which NIC is charged for replication.
If there are any questions regarding this issue, please be free to let me know.
Best Regard,
Jim
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected]
Jim Xu
TechNet Community Support

Closed loop configuration question

I have a motor(with encoder feedback) attached to a linear actuator(with end limit switches).
The motor has a commercially bought servo drive for control.
The servo drive will accept either a step/direction (2 seperate TTL
digital pulse train inputs) or an analog -10 to 10vdc input for
control.
The purpose is to drive a linear actuator(continiously in and out) in
closed loop operation utilizing a ( (SV) Setpoint variable)value from a
file converted to a frequency to compare with an actual ( (PV) Position
variable) measured frequency.
I have created and experimented with individual vi's allows analog
control and digital pulse train control (thankfully with the help of
examples).
Before I pose my question, I would like to make the following
observations: It is my understanding that Closed loop control
means that I dont need to know an exact position at which to drive, but
constant comparision of PV and SV through PID applictation.
Without getting into any proprietery information I can say that the
constant positioning of the linear actuator will produce a latency of 2
to 3 seconds based on the time the actuator moves to a new position and
when the PV will change. While experimenting with the analog
input, i noticed imediate response to motor velocity, but after the
motor is stopped, position is not held in place. However, while
experimenting with the Digital pulse train input, I noticed that the
servo drive can only accept one command at one time; if, halfway
through a move, position error produces a response to move the linear
actuator in the opposite or different direction, the origional move
must finish first.
Can anyone recommend the proper configuration for the closed loop control i have described?
If I can make the system work with the servo drive/motor I plan to use
the simple (pci 6014) daq card with the Analog out, or utilize the
digital out.
If I cant get this to work, we do have a pxi with 7344 motion card(I
would like to exhaust all efforts to use the PCI 6014 card).
Depending on where I go from here, I planned to use the PID vi's for the loop control.
Thanks,
Wayne Hilburn

Thanks for the reply
Jochen. I realize there is a built-in latency with windows but I
think the I/O control would be ok. A change in actuator position
will not result in an immediate change in process variable; Is
there a way to measure the latency or is it calculated? A
satisfactory reaction time could be from 1 to 1.5 sec.
Use of the PCI-6014 is to supply the control output to the servo
drive/amp, and not to drive the motor itself. As stated earlier,
while using the 6014 board, I have the choice of digital or analog
output.
Currently I am at a point where I must choose which configuration,
analog control or digital control(in the form of digital pulse train),
(i am inserting from first message)
While experimenting with the analog
input, i noticed imediate response to motor velocity, but after the
motor is stopped, position is not held in place. However, while
experimenting with the Digital pulse train input, I noticed that the
servo drive can only accept one command at one time; if, halfway
through a move, position error produces a response to move the linear
actuator in the opposite or different direction, the origional move
must finish first. .
I dont claim to understand all the limitations with the
specific boards, however, i am using an approach that is showing me the
characteristics(a couple are listed in the above paragraph) of
the hardware and software configurations.
So I am really back to my origional question; Which configuration
would be better for closed loop control, analog or digital pulse train?
Thanks,
Wayne Hilburn

Multiple Oracle Configuration Question

We have a typical environment setup. I will explain it below:
Our application works in Online and Offline Mode. For Online mode we connect to Oracle 10g enterprise server and a Local instance of Access and In offline application totally works in Access.
Now we want to move away from Access and have Oracle PE instead just because we want to use stored procedure and same set of code for offline and online processing.
So a typical user machine will have a PE instance and a Oracle Client. Currently we use LDAP.ora for Configuring connections. Now i have few questions
1. How do we ensure that Oracle PE will work when we don't have network connection. Can we have like PE setup with Tnsnames.ORA
2. What can be the smallest possible package for PE.
3. Can I use one client to access both PE and Server databases.
Any help will be highly appreciated.
Thanks in advance.

Assuming the "Xcopy installation" refers to using the Windows xcopy command, can you clarify what, exactly, you are installing via xcopy? Are you just using xcopy to copy the ODP.Net bits? Or are you trying to install the Oracle client via that approach?
If you are concerned about support, you would generally want to install everything via the Oracle Universal Installer (barring those very occasional components that don't use the OUI). Oracle generally only supports software installed via the installer because particularly on Windows, there are a number of registry entries that need to get created.
You can certainly do a custom install of the personal edition on the end user machines. There are a few required components that I believe have to be installed (that the installer will take care of). I assume your customization will take the form of a response file to the OUI in order to do a silent install?
Justin

CCMS configuration question - more than one sapccmsr agent on one server

Hello all,
this might be a newbie question, please excuse:
We have several SAP systems installed on AIX in several LPARs. SAP aplication server and SAP database is always located in different LPARs, but one LPAR can share application server of several SAP systems or databases of several SAP systems.
So I want to configure SAPOSCOL and CCMS-Agents (sapccmsr) on our databse LPARS. SAPOSCOL is running - no problem so far. Due to the circumstance that we have DBs for SAP systems with kernel 4.6d, 6.40 (nw2004), 7.00 (nw2004s) I want to use two different CCMS-Agents (Version 6.40 non-unicode to connect to SAP 4.6d and 6.40 + Version 7.00 unicode to connect to SAP 7.00).
AFAIK only one of these can use shared memory segment #99 (default) - the other one has to be configured to use another one (e.g. #98) but I don't know how (could'nt find any hints on OSS + Online Help + CCMs-Agent manual).
Any help would be appreciated
regards
Christian
Edited by: Christian Mika on Mar 6, 2008 11:30 AM

Hello,
has really no one ever had this kind of problem? Do you all use either one (e.g. windows) server for one application (e.g. SAP application or database) or the same server for application and database? Or don't you use virtual hostnames (aliases) for your servers, so that in all mentioned cases one CCMS-Agent on one server would fit your requirements? I could hardly believe that!
kind regards
Christian

Master iPad configurator question concerning cart syncing with different versions of iPads.

I have a question concerning configurator syncing.Can the master iPad be a different version of iPad than the other synced iPads? For instance can iPad 2 be the master iPad to a group of iPad Air's? The iPad 2 has some fewer capabilities than the Air, would some settings or restrictions be left off of the iPad Airs if they were set up this way? Thanks.

There is no such thing as 'master iPad'. If you're using Configurator or Profile Manager control of the setup is done from a Macintosh.

Exchange server 2010 DAG configuration

Dear Boss,
I would like to configure Exchange server 2010 with DAG . I have test lab . i would like to tell my test LAB setup .
One domain controller win-2008 X 64 Ent
Two Exchange server 2010 ( Role - Client Access, Mailbox) Each Server Two Network Cards with Different Classes
IP 192.168.44.50 , 51
IP 10.0.0.10 , 20
One Exchange server 2010 ( Role - Hub Transport )
IP 192.168.44.53
Pls tell me how can i create DAG
Note:- i would like to test below steps
1. Exchange server1 may be down or network link down how server 2 to work automatically without any disturbance
2. Exchange server2 may be down or network link down down how server 1 to work automatically without any disturbance
3. Hub transport server maybe down how it can be work ?
Regards
Subash

Hi Suriya,
To create a DAG, simply use the below commands from Exchange Management Shell:
New-DatabaseAvailabilityGroup -Name "DAGNAME" -WitnessServer HUBSERVERNAME
Add-DatabaseAvailabilityGroupServer –Identity DAGNAME -MailboxServer ExchangeServer1
Add-DatabaseAvailabilityGroupServer –Identity DAGNAME -MailboxServer ExchangeServer2
New-MailboxDatabase -Name DB1 -Server
ExchangeServer1
Add-MailboxDatabaseCopy -Identity DB1 -MailboxServer
ExchangeServer2
You can run your tests now, by restarting any of the servers, and you should be able to see the DB1 will automatically failover & failback between the nodes with out any intervention.
for the HUB transport you must have another server to achieve high availability, so you can install the HUB role on a different server or add it to one of your existing servers.
Mohammad Saeed | MCSE 2003 | MCTS: Lync, OCS, Exchange

Setup/ Configuration Question

The network setup I'm using is a wireless G router, Belkin brand, and I have four WRE54G expanders throughout the warehouse. I don't have WEP turned on so I used the auto configuration on all of them. They all made connection and they all work. However, each one of them tends to lose connection from time to time. At least once every couple of weeks I have to reset one of them. When they stop working the red light comes on and I know the link is gone. I'll reset it and everything will be fine for a while. I thought I'd try to get into the web utility to check if any settings are off, however because it has been auto configured I'm not sure what the ip address is. It's not the default. We use a 10.x.x.x range and I've scanned the entire range and none of them show up on an IP. The only thing that does, besides the computers connecting, is the router. I've run the linksys setup utility and had it do a site survey but it keeps coming back saying that the site survey failed. I hate to take them all down from where they are mounted and physically connect them to check things, but I'm not sure it that's the problem. Any ideas would be appreciated. Thanks. If the question I am asking here has already been addressed, please point me to the related thread.
(Edited subject to keep page from stretching. Thanks!)
Message Edited by JOHNDOE_06 on 06-21-2007 08:57 AM

Still kinda funny that the site survey fails. Are you using a Vista computer? Saw that using a XP computer solved someone's problem.
If you can't get the setup software to work you really need to find out what IPs were assigned to the REs to access the IE interface or hard wire them (v2 and 3). I know it is alot of work. I guess you have to assess how much of a hassle it is.
I don't know if the RE shows up on ipconfig/all. I guess it should since it has a unique IP address. Mines the default so I'll check and repost.
I'm wondering what the effect is of having 4 REs in relatively "close" proximity is? When mine loses connection (infrequently), the light turns red but immediately turns blue cuz it connects to router again (got only 1 RE). Would your's connect to the router or to another RE? If it connects to another RE, I guess you lose half the speed again. Interesting....
Also, other than the blue lights, do have any other indication that the REs are working, e.g. increased signal?
Message Edited by Luckydog on 06-21-2007 11:53 AM
Message Edited by Luckydog on 06-21-2007 12:02 PM
Message Edited by Luckydog on 06-21-2007 12:13 PM

Oracle hardware and storage solution configuration questions

Hi all,
I am configuring hardware and the storage solution for a project and am hoping to have some questions answered about using Oracle as the storage solution.
The current setup will have 2 Dell NX3100 NAS gateways each with dual quad core processors, 24GB of RAM, 12x2TB data disks, and running Windows Storage Server 2008 64bit as the OS.
Will also have direct attached storage of 2 Dell PowerVault MD1200 disk arrays, each disk array with 12 x 2Terabyte SAS disk drives giving a total of 36TB of storage space for each NAS Gateway.
Based on this information, is there any problem with two Oracle Standard Edition installation (1 per NAS) holding up to 36TB of data (mostly high res images) in this hardware configuration?
Does Oracle have a built in solution for replicating data between the 2 NAS heads and down to the disk arrays? Where the application sever will write to one of the NAS+disk arrays and then that data is written from the first NAS to the 2nd NAS+disk array? Currently I've used DoubleTake in other projects but am wondering if Oracle has something similar that is built in.
Finally, will Backup Exec Oracle agent work with this configuration for backing up the data to a Dell PowerVault ML6020 Tape backup device?
Thanks in advance for any insight.

Hi,
Does Oracle have a built in solution for replicating data between the 2 NAS heads and down to the disk arrays? Where the application sever will write to one of the NAS+disk arrays and then that data is written from the first NAS to the 2nd NAS+disk array? Currently I've used DoubleTake in other projects but am wondering if Oracle has something similar that is built in.NAS - I still doubt during the network issues (In case of RAC - all nodes would get afftected), I would not suggest certainly for this. Let the other experts reply back.
- Pavan Kumar N

SQL Server 2012 Failover Cluster configuration questions

Hi,
I have few questions on , SQL Server 2012 Failover cluserting pleasse provide suggestions:
1) In SQL Server 2012 is there a configuration for active / passive Failover Cluster installation? If so how is it done? if you could provide any links or articles that would help.
OR
Is this been replaced by Always ON Availability Groups?
2) Also in our environment we have done active/active installation but at a time my understanding is only node has the ownership to the shared storage versus both the nodes, is that correct? If not please provide an explanation?
Any additional information would be valuable in clearing my doubts?
Thank youy
Malini=

Hi malinisethi,
If you install SQL Server in a cluster and configure Active-Passive cluster. In the first node, select “New SQL Server Failover Cluster installation” option , when we are installing Active-Passive cluster, we have to specify one virtual/network name. (Note:
For Active-Active clustering you have specify different network names as per the number of nodes). on the other nodes is similar to installing on the first node except that we have select the Add Node to a SQL Server failover cluster option from the initial
menu. For more information, there is a similar issue about SQL Server 2008 Active-Passive/Active-Active cluster installation, you can review the following article.
http://sqldbpool.com/2009/10/07/sql-server-2008-active-passive-cluster-installation/
About Active/Active SQL Cluster, two clustered SQL Server instance are created in different nodes. Then apply Active /Active configuration of both instance. There is an example about creating an Active/Active SQL Cluster using Hyper-V. you can review the
following article.
http://blogs.msdn.com/b/momalek/archive/2012/04/11/creating-an-active-active-sql-cluster-using-hyper-v-part2-the-clustered-instances.aspx
Regards,
Sofiya Li
Sofiya Li
TechNet Community Support

Remote configuration question

Hello! I have several questions about configuration in my system that is shown on picture.
I need to have a possibility to program the second FPGA(Virtex-6) and its flash memory. I'm going to send mcs or bit file via ethernet to FPGA 1(Kintex-7) then programming in JTAG-mode FPGA 2 or its flash. First of all, i need to develop JTAG configuration logic at FPGA-1. Then, i have a questions:
1) Is it possible to detect in the jtag chain a flash memory of the FPGA 2 and programm it via FPGA-1? Or its only possible to programm it only using Impact and jtag-programmer?
2) I would like to know if my jtag-configuration logic (at FPGA-1) will have mistakes, is it possible to damage fpga-2 by sending wrong sequences of bits during configuration it "on fly"?

XSVF is something like taking a straight-forward iMPACT programming process, and then recording the transitions of the JTAG signals. Then what you do is to "play back" the recording to make the same thing happen within your target system. Pretty much anything you do in iMPACT including indirect flash programming (SPI or BPI) can be converted into XSVF.
You could also roll your own JTAG conversion code, but I think that will take a lot more effort. I would not be too worried about damaging the FPGA, however. Typically errors in the configuration process are detected as CRC errors and prevent the part from running bad codes.

DAG Configuration Question

Similar Messages

Maybe you are looking for