Daisy Chain TB Display

I have tried to daisy chain a second TB display to my 13" MacBookPro. One display works but not the second. Is there a software issue or is there something I am not doing correctly.

Thanks turbostar and Jeff. Kinda answers the question but the table at http://support.apple.com/kb/HT5219?viewlocale=en_US has a small caveat at the bottome that says:
"You can connect a second Apple Thunderbolt Display (27-inch) to a MacBook Pro (13-inch, Early 2011) and (13-inch, Late 2011), but the built-in display on the MacBook Pro will go dark. This is expected behavior."
So, where are the instructions for this to actaully happen?
Thanks!

Similar Messages

Daisy chain two display port monitors (Dell U2913WM) to new Mac mini Thunderbolt?

Everything I read said that I could hook up a display port monitor to a Thunderbolt port on the mac mini. I purchased two display port monitors (Dell U2913WM) that can be daisy chained, and hooked them up. All I get is mirroring. Does anyone know how to turn off mirroring with this setup? I did not get the "uncheck mirroring" option in preferences until I hooked up the second via the HDMI port instead of a daisy chain. The problem with that is, I cannot take advantage of the full resolution through the HDMI. It seems I have wasted my money on two monitors.
Looking for advice on:
1) How to daisy chain these two Dell monitors to the mac mini and turn off mirroring and use an extended desktop, or
2) How to take advantage of the full resolution through HDMI port?
Any help would be greatly appreciated.
Thanks!

So re-reading this thread, I now realize you did exactly what I wanted to do but your issue was having a cloned vs. extended desktop. Oops!
I believe your "nothing plugged in" issue is the cable. I'm not sure that TB cables are backwards compatible with DP - I think it's only the ports. Do you see multiple monitors in "System Preferences > Displays" if you hook the monitors up like you described in your OP?
My Dell U2713H arrived today and it works like a charm with the supplied Mini-DP to DP cable. The built-in display on my 13" mid 2009 MBP still works if not in clamshell mode, although I will mostly use mine in my HengeDock. In the OSD of the monitor, you can access "Display Settings > Display Info" and it will show you the DP capability. Mine is only DP 1.1a and I believe to run 2 of these at full resolution you will need the bandwidth in DP 1.2 which includes MST (daisy-chaining). This could be your problem.
Can you access the same menu in your OSD and report back what your DP compatability is?
Thanks!
mgb

Imac 5k daisy chain thunderbolt display?

Hello everyone. Quick question on iMac 5k. Can I daisy chain 2 thunderbolt displays to an iMac 5k? I currently have one thunderbolt display connect to it, want to see if i can add another thunderbolt display. Thank you for the help.

I believe you may do that provided the iMac is at the end of the chain, so the external drive must be able to pass through the port. But Apple's information on chaining is in relation to their standalone displays which must terminate the chain. So I am assuming that may also apply in your case even though the iMac isn't a standalone display.
It may be much simpler to use an USB external drive.

Daisy Chain DP 1.2 Monitor

I am looking to purchase a Dell Ultrasharp U2913WM 29" Ultra-Wide Monitor and I noticed that it has Display Port 1.2 capabilities through a displayport out and therefore has the ability to daisy chain multiple displays over displayport.
I was wondering if the Thunderbolt connector would allow me to take advantage of the Dell Ultrasharp U2913WM dasiy chain capablities considering it is compatable with Display Port.

ashayer wrote:
I found a solution which might work well for most people. If your monitor is HDMI compliant you can use this dock and get two monitors. Not the most ideal solution but it worked for me.
http://www.caldigit.com/thunderboltstation/
Thanks, I have already ordered the Caldigit Thunderbolt station, but this DOES NOT solve the dp1.2 issue at all. In summary, I can hook up both my Dell U2713H monitors today and will also be able to do it via the Caldigit Thunderbolt station, HOWEVER but both require using two ports, MDP for maximum resolution versus HDMI. I would like to use dp 1.2, which is supported by Intel on TB2, to eliminate using both my TB ports. However, for some reason TB2 on Apple products are preventing utilization of dp 1.2,

Daisy chain monitor from cinema display MacBook Air 5,2

I know the Mid-2012 MacBook Air is capable of 2 external displays as described here.
The monitor works when plugged directly into the MBA, but not when daisy chained from the back of the cinema display.
It's a dell monitor, and I'm using an Apple Thunderbolt-VGA adaptor.
Is there something I'm missing? Thanks!

As far as my question itself -- why does this happen? Has anybody had this issue on Lion and had it resolved on Mountain Lion?

Thunderbolt daisy chain problem with display

Hi to everybody,
being a proud new user of a thunderbolt audio interface Apollo Quad since a couple of days i am struggling to set it up without trouble for my secondary display in my Thunderbolt daisy chain...
My setup and connections
MBP Late 2011 17" 16GB RAM running Mavericks and UAD SW 7.11, 1 Thunderbolt port
Promise Pegasus R4 Thunderbolt RAID drive
Apple TB display
Second 26" display connected via DVI/Mini display port adapter
Erverything worked like a charm prior to inserting the TB audio interface with a Thunderbolt 2 Card into the TB daisy chain. Order of TB connections: MPB -> Apple TB display -> TB Audio interface -> Ext. display via DVI to TB connector.
Since putting the audio interface (Apollo) in the TB chain Apollo itself, TB display and Pegasus RAID run fine - but the last display behind Apollo only shows "invalid mode" blinking on the display. I tried changing the order of the devices, no change.
Has anyone an idea what to do?? - I have not exceeded the max number of TB devices (6) allowed to run in sequence. I read here in the forum that an ext display behind Apollo should work and has proven to do so. It has the new option card for TB2 inserted... Does the left/right port matter, which is connected to the display?
Thanks in advance for any help to get that sorted out!! The last option would be to go remove the TB card and run the Apollo per firewire as I need the second screen.. not the most convincing solution for me though.
Regards
Uli

Hi Ilya,
I am curious why it only happens for one particular Process Chain. Normally displaying a log has nothing to do with the client settings of SCC4 and/or system settings of SE06. My only guess is that it might be created in this system directly and that the system wants to modify anything here.
I am quite sure that the system is "closed" and it's not a Development system, e.g. a Production System. Please confirm.
Anyway, I have one suggestion and that is to check the Object Changeability in the Transport Connection. Go to t/code RSA1, choose the Transport Connection view and click on the push button Object Changeability.
Here you can see a list of Object Types like RSPT (Process Chain Starter), RSPV (Process Variants), PSPC (Process Chain). If it is set to "Not Changeable", I suggest to change that in e.g. "Everything Changeable".
Please try that with the above mentioned Object Types for Process Chain related Object Types and see if you are able to display the log w/o the pop-up.
You can also refer to SAP Note 337950 - Queries (including objects) cannot be edited for more information.
Thanks,
Sander

2 thunderbolt displays worked fine daisy chained, moved one to work in other room, now only one will work. both work independantly or both plugged into my macbook pro.

I have 2 thunderbolt displays and have had them daisy chained for months where I only would plug one into my macbook pro 15" retina and both displays have worked great. The other day I moved one of them into the conference room, connected also a HDMI cord to a projector to do some work with staff on software design.
I brought my thunderbolt back into my office and plugged it back into the other thunderbolt dispay, then plugged the other display back into my macbook and started it up and now I can only get one to work daisy chained. They both work great independantly or if both of them are plugged into my macbook pro, but not daisy chained any longer.
Is there a setting I need to look at to maybe reset so that my macbook pro will use both thunderbolt displays daisy chained?
Thanks for anyones advice and sharing any similar issues and how you fixed the issue.

Hi there,
The first thing that I would recomend is resetting the PRAM on your portable.
OS X Mountain Lion: Reset your computer’s PRAM
http://support.apple.com/kb/ph11243
If the issues persist, then you may need to force the device to detect displays.
OS X Mountain Lion: About the Display pane of System Preferences
http://support.apple.com/kb/ht5369
How can I detect displays?
If the detect displays option is not available, hold down the Option key while you are in the Display pane.
- Griff W.

I want to daisy chain my 15 inch mid 2012 non retina macbook pro to a 2012 27inch imac and then to a 27 inch thunderbolt display

I have a mid 2012 non retina 15inch macbook pro, and a 27inch 2012 imac, and a 27inch thunderbolt dsplay and I want to use the imac and the thunderbolt display as dual monitors for my macbook pro and daisy chain them together. I have an extra thunderbolt cable, How would I go about doing this, every time I try to connect it via Target Display mode it only shows up on the imac and the thunderbolt diplay shows the imac screen but I cannot access anything on it. I would love some help, I am probably just missing something simple.

Yes there is on Mac computers that do not come from the factory with "Built In", Note the Words Built In, DVD drive.
On all Mac computers that come with Built In DVD drive Apple has Restricted the installation of Windows from ONLY That Built In drive and Only when it is Physically installed inside the system.
Many people have tried what you want to do and to my knowledge None have been successful.
It is something that is Hard Wired, Written, into the Firmware of these Mac computers.
Some have tried installing Windows on the standard HDD and then moving that HDD to the optical bay or leaving it in the main bay and installing a SSD into either the main drive bay or optical bay and have been greeted with the system not booting to either OS or not booting to Windows.
Something about how boot camp sets up the drive and possibly makes changes to the Firmware or EFI partition on the drive that Windows is installed to or to both that restrict it. You can't even make another Mac OS X partition on that drive without screwing up the Windows install.
To your last post the Answer is NO as stated above.

Can I daisy chain two Thunderbolt displays to the new MacBook Airs (July 2011)?

I have last year's MacBook Air -- probably the best Mac I've ever had and I've had a few. I looked at using multiple displays last year, but the reviews for the major 3rd-party solutions really demonstrate how little is possible.
I see Apple says you can double up on displays for the MacBook Pro (I have a pre-Thunderbolt one unfortunately), what about the new (July 2011) MacBook Airs?
Anyone tried? Anyone know?
(I have a 30" Dell display, but it is, and always has been, very flakey when it comes to connecting to a Mac laptop).

You can thank Intel for that.
The sandy bridge chips all have integrated graphics, and before they were released -- they took nvidia to court claiming they didn't have a "license" to make GPU chipsets for the sandy bridge line. Intel won, and consumers lost.
The solution most manufacturers are using for notebooks is graphics switching (nvidia optimus like technology) -- which basically uses a discreet GPU along side the intel integrated GPU, and switches between the two instantaenously based on the workload and \ or battery life -- this is how the macbook pro's with the ATI gpus work.
Since there isn't enough space physically inside a macbook air for a discreet GPU, and since no company in the world is allowed to make a shared GPU for intel's sandy bridge chipsets -- the only solution is to use the integrated graphics that is in the processors -- Intel HD 3000. Intel basically has the monopoly here...there is no legal solution in the world another company can provide thanks to our wonderful court system
Wanna know the really sad part about the Intel HD 3000 GPU? The Nvidia 320M (the GPU used in the previous model 2010 macbook air -- chip was released to the market in April of last year) actually out performs it in some benchmarks -- that's right, a 1+ year old shared gpu from nvidia outperforms Intel's 2011 integrated graphics.
Intel ***** at graphics, period.
The only other solution I can think of is for you to get the "Echo Express" product from Sonnet:
http://www.sonnettech.com/product/thunderbolt/index.html
It's basically an external bay that will allow you to put a PCIe GPU inside it, and it would then connect via thunderbolt to the macbook air.
You would then use the minidisplayport connectors on the PCIe GPU to connect to the apple displays -- I believe any modern ATI or Nvidia GPU can support up to 3 or 4 external displays.
Unfortunately, sonnet's bay is not released yet, and you'd also have to make sure the PCIe GPU you get supports both thunderbolt AND os x....so yeah, kind of slim pickens right now
EDIT:
So apparently the macbook pros can daisy chain two thunderbolt displays -- Apple has a picture of it on their site:
http://storeimages.apple.com/1867/as-images.apple.com/is/image/AppleInc/MC914_AV 7?wid=1200&hei=1200&fmt=jpeg&qlt=95&op_sharpen=0&resMode=bicub&op_usm=0.5,0.5,0, 0&iccEmbed=0&layer=comp
I just bought a new mac air too...I was gonna get a mbpro but they are just too expensive -- the one I configured was at around 3000$
Wanna know what's lame about using the thunderbolt display with the mac air? So the new mac air has the magsafe connector on one side and the thunderbolt connector on the other -- they're not on the same side like the macbook pro is (see picture) -- so basically the cable is going to have to slack around the back of the macbook air -- who designed that? Must have been smoking some good meth ;p
Message was edited by: NiqueXyZ

Daisy chain 2 thunderbolt displays by direct connect

I was hoping to hook up 2 thunderbolt displays to a mac mini. With the way the screens are set up, they will be nearly 6' apart from each other, which makes connecting the pigtail of screen two to screen one impossible. I havent' been having a lot of luck with finding reviews of reliable extention cables that are known to work, but I have been seeing a ton of thunderbolt to thunderbolt cables (6' and 9'). Is it possible to daisy chain from the 1 open thunderbolt port on display one to display two and leaving the pigtail detached?
Thanks!

Much obliged!

Daisy chain Display Port (U2713H)

Hi Forum,
I have a rmbp 15 and 2 Dell U2713H screens that I usually connect to my macbook using both TB/DP ports.
Now I need to connect another TB device and looked into using the Daisy Chain option on the screens. Although I get image, it seems to be cloned and MacOS doesn't seem to know that the second screen is there.
My question is, how can I enable Daisy Chain on MacOS?
According to the specifications this should Work.
Device
connector
Device
Connector
Device
rMacbook Pro
miniDP to DP
Dell U2713H
DisplayPort 1.2 to DisplayPort 1.2
Dell U2713H
In theory this should work. Can anyone help me with this?
Thanks in advance,
Tiago

I am the OP.
Please see what I found on another thread that answered my question.
I just finished researching this for myself, as I was considering adding to my MacBook Pro (2012) a pair of new Dell U2713H 27" monitors that support DisplayPort-based daisy-chaining.
It looks like Thunderbolt-enabled Macs only support DisplayPort 1.1a which will not allow the kind of MST that you are looking for nor will it enable me to use multiple monitors as I desired. New Thunderbolt chips supporting DisplayPort 1.2 with MST are supposed to be available this year, and so would possibly make it into late-2013 or 2014 Macs.
It seems the only present ways to connect more than one external monitor to a MacBook are:
a) using a USB video adapter
b) purchasing two Apple Thunderbolt Displays
If someone releases a Thunderbolt docking station with multiple monitor outputs there might be hope, otherwise I think this won't ever be possible with current model MacBooks.

Daisy Chain 2 cinema displays to thunderbolt port on iMac?

Presently I have an iMac (mid 2011). I am running 2 cinema displays thru my 2 thunderbolt ports on my iMac. Is it possible to daisy chain these 2 additional displays to save a thunderbolt port? If so, how would be greatly appreciated.

Only Thunderbolt displays are capable of being daisy chained.
If you had one Thunderbolt Display and a Cinema Display then you could put the Thunderbolt Display first and then connect the Cinema Display into it, but it cannot be done with two Cinema Displays.

Daisy chain 3 thunderbolt displays to MBP 15"

Hello,
A simple question here,
I would like to know if there is a way to daisy chain 3 (three) thunderbolt displays to a 15" MacBook Pro, maybe if the laptop is in clampshell mode?
Thanks for any help

Two:
http://support.apple.com/kb/HT4885

Daisy-chain a thunderbolt external drive & thunderbolt display?

Although you can't daisy chain multiple thunderbolt displays to the new (mid 2011) Air's are you able to connect a thunderbolt display and daisy chain a thunderbolt external hard drive?

1. As stated in the questions and answers section of the link you posted, no.
2. Connect it to the MacBook Pro, start File Sharing from the Sharing pane of System Preferences, and use the Connect to Server command in the Finder's Go menu on the iMac.
(102303)

Daisy Chain 24" Monitor to 27" Thunderbolt Display

Hi everybody,
I have the 2011 MBP with the 6750m and I want to buy the new 27" Thunderbolt Display. Currently, I'm using a Samsung 24" DVI Display with the Display Port to DVI adapter that I bought with the MBP.
I was wondering if I can continue to use the 24" and daisy chain it to the Thunderbolt Display?
Best,
Luka

Kevin can you confirm this? Do you have a Thunderbolt Display, with a MiniDisplayport to DVI hooked up to your Dell laptop? I presume this works, but that you only have the monitor and speakers working, without the USB/Ethernet/TB port that are on the back of the display?
I am waiting for somebody to test this so I can decide to buy the display yes or no so please let me know asap : )
Thomas.

Daisy Chain TB Display

Similar Messages

Maybe you are looking for