Daq usb to ethernet

I am using a DAQ (I think it is a 6009 but am not sure of the exact model number) and currently I have it connected to my laptop using the provided usb cable to read in digital data. I was wondering if it is possible to hook up a usb-to-ethernet adapter to the usb port on the daq and connect it to my laptop using an ethernet cable. Is this possible? If so will by labview code running on my laptop change? Currently I am using the dap assistant to read in from the daq.

I think we need to get some terms straight. If you are talking about a USB-Ethenet adapter where the adapter is an addtional network interface for the pc, there is no way to even physically connect this to the USB-6009. The 6009 has an B type connector and you use a cable with a A type connector that plugs into a hub on the pc. USB-Ethernet adaptors willhave the same or often just a cable with a A type adapter that can only be plugged into a pc. The Ethernet side of the adapter has an RJ-45 connector and obviously, you can't plug your DAQ device into that.
On the other hand, there are USB extenders and this may be what you mean by USB-Ethernet. Many of these extenders use CAT-5 cable between the pc and the device. One part of the extender plugs in the A type connector on the pc and the other part of the extender also has an A type connector that you would plug your device into. I believe most of these amplify the signals and with low noise CAT-5 cable, you can place the USB device further away than normal. I have seen things called USB servers and these are network devices. Judging by questions other users have made about extenders, you may or may not get the extender to work. Apparently NI does not test or certify any extender. I would suggest doing a search of the forum for 'USB extender' to see what other users have gotten to work.

Similar Messages

  • Usb to Ethernet  adapter doesn't work? AX88772B

    I don't know how to make a connection with Internet with RJ-45 cable with the usb adapter.
    I have MBA. Lion 10.7.5
    Now I need to connect MBA by RJ-45 cable with usb adapter (asus AX88772B)
    MBA see the adapter (even without an ethernet cable).
    I also did download drivers from here http://www.asix.com.tw/products.php?op=pItemdetail&PItemID=105;71;101&PLine=71
    I read the instruction, and I've done 3 steps on the page 4 exept these one's:
    (4)  Set the permission access mode of Apple’s default driver.
    (5)  Update the access and modification times of ASIX’s AX88772B/772A/760/772 or AX88178 driver.
    But i don't know how to do this.
    In the system report is always written this:
    AX88772B:
      Product ID:          0x7e2b
      Vendor ID:          0x0b95  (ASIX Electronics Corporation)
      Version:           0.01
      Serial Number:          09EF51
      Speed:          Up to 480 Mb/sec
      Manufacturer:          ASIX Elec. Corp.
      Location ID:          0xfd120000 / 4
      Current Available (mA):          500
      Current Required (mA):          Unknown (Device has not been configured)NO
    But still I can't make an Usb to Ethernet connection in system preferenes, nothing written about it there.

    Hmm. Well I tried rebooting with wifi off but that didn't fix things for me. Would you mind sharing what your System Information says under Thunderbolt? This is what mine looks like:
    MacBook Pro:
      Vendor Name:          Apple, Inc.
      Device Name:          Macintosh
      UID:          0x0001000D1290C120
      Firmware Version:          11.1
      Port:
      Status:          No devices connected
      Link Status:          7
      Link Controller Firmware Version:          0.11.4
      Port:
      Status:          Connected
      Link Status:          2
      Link Controller Firmware Version:          0.11.4
    Thunderbolt to Gigabit Ethernet Adapter:
      Vendor Name:          Apple, Inc.
      Device Name:          Thunderbolt to Gigabit Ethernet Adapter
      Vendor ID:          0x1
      Device ID:          0x8003
      Device Revision:          0x1
      UID:          0x000100020059EBB0
      Apple Serial Number:          DTN224606LWDWKHAX
      Route String:          3
      Firmware Version:          5.5
      Port:
      Status:          Connected
      Link Status:          2
      Port Micro Firmware Version:          0.0.8

  • I've bought an USB-to-ethernet-adapter and a minidisplay-port-to-VGA-adapter. But I can't use them at same time. At first, I plugged those two adapters and only the USB-to-ethernet worked. Tried restarting the mac then only VGA adapter worked.

    I've bought an USB-to-ethernet-adapter and a minidisplay-port-to-VGA-adapter. But I can't use them at the same time. At first, I plugged those two adapters and only the USB-to-ethernet worked. I tried restarting the mac then only the VGA-adapter worked. I also tried to reinstall the OS.
    I'm using new 13-inch MacBook Air early 2015. OS X 10.10.3.

    Thanks Malcolm - Do you think it might be worth trying to flash the firmware on these cases - there seem to be updaters available on Prolific's website. Obviously I'd have to do it on a PC. I've emailed Prolific asking them about my problem. No reply as yet, and I'm not holding my breath! Do you know if there are any other posts on these boards relating to Prolific? Stupid question really - I'll just do a search...
    Thanks again for your post. Cheers from Bonnie Scotland.

  • Third-Party USB to Ethernet Adapter not working since 10.8 updated

    Hi I have a third-party USB to Ethernet adapter. Since the update of mountain lion the adapter does not work.
    Is there a driver or something I can do to make it work?
    Thanks

    USB not so good, this very good.
    Thunderbolt to Gigabit Ethernet Adapter

  • Unusual issue with tag engine and BELKIN USB to Ethernet adapter??

    I have an .scf file with 72 tags and several tag groups in it. If I open the tag engine without the usb adapter, I can read the tag group names with the get group list.vi. The tag group names are listed in black letters when wired to an indicator. When I plug in the usb ethernet adapter, immediately the group tag names are greyed out in the indicator without even running the vi. If I put a tag constant on the block diagram and try to select a tag name with the pointer, no tagnames pop up. It worked yesterday and my IT. department sent down a shockwave and flash5 update download when I booted up this morning. anyone have any ideas??

    I am still seeing the tag groups disappear when I start the tag engine on labview7.0. I have several other programs running at the same time, KEPWARE, PROWORX NXT, USB to ethernet adapter. This is on a win2000 machine.
    Attachments:
    op50_head_press_force_status_rev2.vi ‏320 KB
    Process_Sta2_probe_results.vi ‏42 KB
    op50_head_version2.scf ‏53 KB

  • HELP: USB to Ethernet Adapter

    Hello Everyone. I have a USB to Ethernet adapter for my Macbook Pro Retina. After plugging it into an ethernet cable and connecting everything, my computer still isn't reading it. I am wondering if there is an install driver or what or if I am doing something wrong. Thanks you for your help.

    Brb8910,
    what is the brand and model of your USB-to-Ethernet adapter? Does the manufacturer claim that it is compatible with your installed version of OS X?

  • Apple USB to Ethernet Adapter??

    Can you use the Apple " usb to ethernet " adapter with the airport express?

    The USB port on the AirPort Express will only support a compatible printer, so using a USB to Ethernet adapter would not accomplish what you want to do.
    If you add a simple 5 port Ethernet switch to the AirPort Express, one port will be used to connect to the Express with an Ethernet cable. You will then have 4 Ethernet ports available for devices.
    Any major electronic/computer store will have what you need. Netgear or Cisco-Linksys make quality products.

  • Yoga 13 - Compatible USB to ethernet devices for PXE booting

    Hi there, 
    I've recently been looking for a means to pxe boot the lenovo yoga 13 to enable me to then image it. After reading that pxe booting is possible I went out and bought a StarTech usb to ethernet adaptor (USB21000S2) but have had no luck so far.. In other postsI've read that pxe booting is only supported if using the official lenovo usb to ethernet adaptor. We're using FOG as our imaging solution (if thats of any use)
    Please can someone confirm if only the official adaptor is supported.
    Regards
    Simon

    Were you able to find any?  I am also very interested in finding one.  I just ordered one of these the lenovo 0A36322 to see if it will work, but it is only 100mb and not sure if it will work or not.

  • Is it possible to maintain the last AO value after the DAQmx task is done on device DAQ USB-6341 ?

    Hi all,
    I use the device DAQ USB-6341 to generate the desired voltage waveform by the "finite samples" sample mode.
    I notice that the channel resets to zero volts after the DAQmx task is done and the DAQ USB-6341 does not have 
    the property AO.idleOutputBehavior to select "Maintain Existing Value".
    How can I maintain the last AO value after the DAQmx task is done on device DAQ USB-6341 ?
    Thanks.
    Godel

    How many computers do you have in the network?
    What is the IP address and default gateway number on your computer?
    In order to connect to the wireless network, WVC80N should get valid IP address from the access point.
    If the access point has capacity to assign a private IP address to the computers and devices then I think you can use WVC80N.

  • Apple USB-to-Ethernet, OS 10.5.4 and a MBAir. Having Issues

    Ever since updating to 10.5.4 on the MBAir, my adjacent Windows XP system has been looking connectivity. Basicly it is consently telling me that the Ethernet cord has been disconnected.
    I mention the Apple USB-to-Ethernet because once I unplug it from the MBAir, the issue goes away on the WinXP box.
    Also, the network connection with the MBAir has been 'flaky' using the Apple USB-to-Ethernet; so 'flaky' behavior when going wireless.
    Wondering if others have experienced anything remotely similar to this. Wondering if maybe its a faulty Apple USB-to-Ethernet.
    Any comments are welcome.

    If the drive is new then it isn't prepped for the Mac. You should do the following:
    Extended Hard Drive Preparation
    1. Boot from your OS X Installer Disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger or Leopard.)
    2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. SMART info will not be reported on external drives. Otherwise, click on the Partition tab in the DU main window.
    3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, set the partition scheme to GUID (for Intel Macs) or APM (for PPC Macs) then click on the OK button. Click on the Partition button and wait until the process has completed.
    4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
    5. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, check the button for Zero Data and click on OK to return to the Erase window.
    6. Click on the Erase button. The format process can take up to several hours depending upon the drive size.

  • I need a USB/FireWire ethernet adapter

    About 6 months ago my ethernet port was fried when a lightning bolt sent a surge through the wire. Since then i have been using my family's wireless network, but now that I am back in school and away from home, i don't have that luxury. So, i've been looking for a Mac compatible USB/FireWire ethernet adapter and have had no luck. If anyone knows where I can find one, let me know.

    Hi Kllru,
    Welcome to the Discussions.
    The following link has info on compatible adapters as well as a driver for OS X.
    http://www.sustworks.com/site/newsusbethernet.html
    John

  • C# apply to DAQ USB-6008

    i have a problem about DAQ USB-6008 of application in c#, i would like to use c# code to program the window that can display the temperature c/f and wave graphic celsius versus time ,which is used in thermal couple,its my first time to use DAQ system ,i have no idea what to start , is there anying information about it?

    USB-6008 沒有冷點補償，所以無法量測溫度。
    建議USB-9211
    http://sine.ni.com/nips/cds/view/p/lang/en/nid/14165
    C:\Documents and Settings\All Users\Documents\National Instruments\NI-DAQ\Examples

  • Can`t setup my Ax88772a USB Fast Ethernet Adapter! Driver is already downloaded

    Can`t setup my Ax88772a USB Fast Ethernet Adapter! Driver is already downloaded

    Can`t setup my Ax88772a USB Fast Ethernet Adapter! Driver is already downloaded

  • HT202617 USB to Ethernet Unable to connect

    I just got the USB to Ethernet adapter and I thought It was a simple Plug-n-Play thing. I was wrong. I am unable to connect to the internet. Any pointers?

    According to reports, the USB-to-Ethernet adapter doesn't work on Macs that have a Thunderbolt port, which yours does. You would need the Thunderbolt-to-Ethernet adapter.

  • Usage of DAQ USB-6211 with Sound and Vibration Measuremen​t Suite

    Hi,
    Could I use DAQ USB-6211 with Sound and Vibration Measurement Suite ? All examples are based on 24-bit devices (usually with IEPE-on) such as NI 9234 or similar.
    I don't need IEPE, 16 bit is sufficient for my dynamic range, could leave without simultaneous sampling - so 6211 (that I have) is OK for me.
    Actually I'm interested in S&V Toolkit ( or Measurement Suite) as a tool with some specific Signal processing capabilities (for example, short-time FFT etc.)
    Thanks in advance

    Hi sgabr,
    Yes, you can use the 6211 with some of the Sound and Vibration VIs, including most of the FFT functions.  I know that's a little vague -- I don't have a list of which functions do or do not support 16-bit devices, but I did test it out on my system this afternoon.  If there are specific functions or examples you'd like to know about, let me know, and I will try them out.
    You also have the option to download the evaluation version of the Sound and Vibration Measurement Suite.  That way, you can test drive it yourself!
    Kyle B  |  Product Support Engineer  |  ni.com/support

Maybe you are looking for

  • Performance tuning in FI

    Hi , Could any one suggest, how I can increase the performance in FI , when i would be generating tax reports? and what are the tables to be used for tax generation?

  • Full database Export

    Hi We are having a database 10g running on solaris OS. We are getting a new server and I need to move the data. This is what I am planning to do. Take full database export from original server. (This includes tablespaces, all schemas and data) Import

  • New OVI Calendar web application syncronization is...

    Hi @ll, I don't know about you, but I can't sync calendar events back & forth since last week (when Ovi Calendar 1.6 went from beta to live). No errors reported by the phone ovi sync app. It's just no calendar appointments being sent (contacts is wor

  • IPod function looses place when playing in the background

    I have an iPhone 3g and since getting it I've been able to cause the iPod to loose its place if I run an application and let it play in the background. If one song is playing and I start any other application in the phone (even built-in ones like the

  • IPhoto Update download problem

    I have OS 10.10.1 and my iPhoto will not open. Says got to App Store for latest update. At the App Store the download process doesn't work and leads me in a circle back to App Store?? Appreciate any advice. GB