Daqmx assistant cannot wire output

I haven't fired up labview in about two months and no have a strange problem. I am trying to setup a new module to acquire thermocouple and RTD inputs. It is a 9213 chassis. When I place the DAQ assitant down and setup the signals in the wizard I never get the "data" stream on my icon. This is the part where you wire it to get the data out. I am sure I am missing something brutally simple but I can't figure it out.
Solved!
Go to Solution.

Hi Icemaker,
If you have pressed the OK button in the DAQ Assistant and you still do not have any inputs or outputs, you should try repairing your DAQmx driver.   Please see the attached document for steps to uninstall or repair software.  
How Do I Uninstall or Repair NI Software?
Regards,
Jim Schwartz

Similar Messages

  • "Extraction Failed: Cannot Open Output File" error message when installing new drivers

    Hello, I'm trying to install new drivers for my HP Photosmart C4385 Printer.  I downloaded the full feature drivers for Windows XP 32-bit, and when I start to install (extract), I get the error message:
    Extraction Failed
    Cannot Open Output File
    And the process closes.  It happens at about 85% extraction every time.
    Any idea why?  I called HP but since it is out of warranty they wanted money, which I think as absolutely ridiculous - won't even give me basic support??  Poor, poor customer service.
    This question was solved.
    View Solution.

    Hi,
    If you haven't still got the  Full Feature software installer, download it from the link below and save it to your Desktop.  If you already have it, place it on your Desktop.
    ftp://ftp.hp.com/pub/softlib/software10/COL20274/mp-53147-4/100_228_PS_AIO_02_Full_USW_enu_NB.exe
    Make sure the Printer is disconnected from your PC.
    Download and install 7-ZIP.  Once installed, right click on the software installer for your printer, select 7-Zip and choose extract files, then click Ok.
    Open the newly extracted folder and double click the setup application to start the installation ( the setup application will probably have the same icon as the original software installer you downloaded ).  Connect the printer to your PC when the software asks.
    Hope this helps.
    Best wishes,
    DP-K
    ****Click the White thumb to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    ****I don't work for HP****
    Microsoft MVP - Windows Experience

  • I just tried to update Firefox to version 9.0.1. It got to 13% extracting, then I got an error message, Cannot Open Output File. Can you please help me?

    I just tried to update Firefox to version 9.0.1. It got to 13% extracting, then I got the error message, Cannot Open Output File.

    The file could be downloaded incorrectly. Could you redownload it again from [http://getfirefox.com http://getfirefox.com]?

  • REP-52251: Cannot get output of job ID

    Hi,
    I am trying to call a report from oracle form and i am getting this error
    REP-52251: Cannot get output of job ID 220 you requested on Mon Oct 16 11:19:12 EDT 2006.
    REP-56033: Job 220 does not exist
    please help, any Ideas.
    Best regards,

    Have you tried to create an URL with all the parameters you're trying to run your report with?
    Try to run the report that way first - just to make sure your report can actually be run with the parameters you're using.
    If that works then try to use WEB.show_document from your form, passing the same URL you just built, if that works then you are only having problems with your RUN_REPORT_OBJECT (I am not sure if you're using rp2rro library for running your reports).
    Try that -- another thing that might be happening is that your output is being generated but due to the parameters (I think there is some form of timeout in the reports server, when the files in your cache are deleted, not sure if this is the problem).
    Try the run the report with an URL first - that should shed some light.
    If you're still having problems, post it here, so we can review it.

  • Boot Camp Setup Assistant Cannot Be Used

    Just installed Leopard on my 20" iMac 2GHz Core 2 Intel Machine. Trying to start up the Boot Camp Setup assistant. Clicking Continue gives me the message:
    Boot Camp Assistant cannot be used.
    You must update your system software before using this setup assistant.
    I confirmed that there are no software updates available, and the latest firmware update from the Apple Downloads page reports back that I do not need the update.
    Any suggestions on getting boot camp to work?
    Thanks!
    Allen

    Backup and do an Erase and Install or re-partition.
    This is how I got the installation I have now, and I'd like to use my external HD anyway, shared between VMWARE and Boot Camp.
    Do you have an eDisk on our HD?
    Nope.
    Do you already have a boot camp partition on your system? More specifically a boot camp beta partition with windows installed on it.
    This machine never saw boot camp at all.
    I wonder if the way I'm partitioned might be the culprit. I cloned off my old 10.4 system, blew everything away, partitioned 2-ways, installed 10.5 on the first partition, and restored my 10.4 installation to the second.
    Message was edited by: fisheral
    Message was edited by: fisheral

  • Firefox setup 9.0.1 exe won't extract (cannot open output file)

    I downloaded firefox 9.0.1 and it won't extract and install on a win7 computer. It says cannot open output file. I had previous versions of firefox for 10 years. I tried disabling AV and firewall also. Please help. Nate

    Thank you! My solution was slightly different, but in the end, seeing what was going on in the Help menu in the browser did the trick. Turned out I had been stuck for who knows how long "downloading" a version 3! Also had a toolbar to disable but not the Ask.

  • REP-52251: Cannot get output of job ID 69 you requested  ....

    OS: Oracle As 10.1.2.0.2 (rel 2 for Linux 86)
    I have moved my forms and reports from windows XP (DS 9.04) to the Linux box.
    I have compiled and run FORMS and most of the REPORTS succesfully.
    I have compiled one report succesufully.
    But when I run this report from the FORM, I got message as below:
    Error
    REP-52251: Cannot get output of job ID 69 you requested on Thu Sep 29 15:37:03 PDT 2005.<P>REP-56093: Cached output for job 69 is no longer valid
    I have checked
    http://abc:7778/reports/rwservlet/showjobs?
    Status is as follows:
    Error
    Finished successfully but output is voided
    Regards,
    DN

    Just in case someone else too finds this thread with google. We had too REP-56093: Cached output for job 5429 is no longer valid. After checking reports cache dir we did see that the problematic reports have cache key with (broken)umlauds. So we disabled :DESNAME parameter and that got rid the umlauds in file names and that resolved the cache error. So if you get this error, you might check the cache directory if the problematic reports have some weird cache files/filenames.

  • Cannot select output tray on a stapler stacker using universal print drivers

    With universal print derivers 5.2, we cannot select output tray for print job on a stapler stacker.  All jobs are set to automatic output and only uses the lower tray, not other trays.

    Hi drlake,
    I understand that you are having issues with printing specialty paper/labels after updating your computer. It would be best if you posted your question on the HP Laser jet Commercial Site <here>.
    This would be the best place to find your answer.
    Thank you
    I worked on behalf of HP

  • Why does Adobe Download assistant cannot start downloading?

    why does Adobe Download assistant cannot start downloading?

    That is likely due to your software firewall not allowing access.  Do you receive any specific error messages?  Which operating system are you using?

  • How to use two DAQmx assistant ?

         I am using 2 DAQmx assistant objectsfor acquiring 2 distinct different signal.when i run it, it is showing following error.
                          ERROR 50103 occured at DAQmx control task.vi:8
                          POSSIBLE REASON : The specified resource is reserved.The operation could not be completed as specified.
        Pls. tell me how can i clear it.
                                     THANK YOU !

    Any chance you could attach your LabVIEW code for us to see? It helps to visualise your issue.
    You may be running the two DAQmx assitants in parallel, and thus they will be trying to access the same resource simultaneously. They probably need to be ran sequentially. To ensure this, try wiring the error out of the first assistant into the error in of the second assistant.
    Thoric (CLA, CLED, CTD and LabVIEW Champion)

  • HT1899 Is Boot Camp Assistant supported in Mac OS X 10.8.1? I am getting an error "Boot Camp Assistant cannot be used. You must update your computer's Boot ROM firmware before using this setup assistant."

    Please advice I am getting an error "Boot Camp Assistant cannot be used. You must update your computer's Boot ROM firmware before using this setup assistant."

    No I have only one physical HDD. Here is a diskutil list result
    /dev/disk0
       #:                       TYPE NAME                    SIZE       IDENTIFIER
       0:      GUID_partition_scheme                        *500.3 GB   disk0
       1:                        EFI                         209.7 MB   disk0s1
       2:                  Apple_HFS Macintosh HD            499.4 GB   disk0s2
       3:                 Apple_Boot Recovery HD             650.0 MB   disk0s3
    Also here is a system info
    Hardware Overview:
      Model Name:          MacBook Pro
      Model Identifier:          MacBookPro8,2
      Processor Name:          Intel Core i7
      Processor Speed:          2.5 GHz
      Number of Processors:          1
      Total Number of Cores:          4
      L2 Cache (per Core):          256 KB
      L3 Cache:          8 MB
      Memory:          8 GB
      Boot ROM Version:          MBP81.0047.B27
      SMC Version (system):          1.69f3
    15-inch, Late 2011
    current situation
    - I've recovered from external drive (mountain lion 10.8.1 ) which i prepared by Lion Diskmaker before.
    Current issues:
    1) I have Recovery HD but when I boot from it - Reinstall Mac OS X option is not working
    2) I have EFI password and won't be able to clear it as well as reset PRAM
    3) Boot Camp Assistant is not working as well with the error in the subject
    Any ideas how to fix all of these?

  • "Unable to save markup: Cannot create output file" message with ISDK

    Hi,
    We have an integration of AutoVue with OpenText Livelink, and we're seeing that if users open a document, and then work on adding mark-ups for a long time (3 hours) without saving the mark-up when the user saves the markup they get an error message "Unable to save markup: Cannot create output file". If they then press the save button they get the out-of-the-box AutoVue 'Save Markup File As' dialog.
    The ISDK DMS integration servlet and VueServlet servlet are both running under Tomcat with 740 minute session timeout set for the servlet.
    When we look at the logs we're not seeing any attempts to save the mark-up, which is confusing.
    It looks as though the link between the AutoVue applet and the DMS has been lost.
    Is it possible to specify session time-outs in the AutoVue applet?
    Is there a way of checking keep-alives are being sent (if they are ever sent)?
    Help appreciated!
    Thanks
    Paul

    AutoVue default timeout is 30 minutes and is being controlled by the option jvueserver.users.timeout (value set in seconds, default is 1800).
    Adding to the jvueserver.properties the following line:
    jvueserver.users.timeout=50400
    would set AutoVue session timeout to 14 hours (longer than Tomcat session).
    If the issue still persists, the AutoVue session timeout is probably not the cause...
    Edited by: user739124 on Dec 4, 2012 12:02 PM

  • Cannot Create Output File Error

    I have a working (and deployed) JSP/ADF application which was written with JDev 10.1.2 that I need to make a change to. Since it was deployed, I've gotten a new computer, and installed JDev 10.1.2 on it. Now, when I open the project on the new computer and try to build it, I get an error
    "error writing class oracle.jbo.http.HttpSessionCookieImpl: java.io.IOException: cannot create output file"
    The source file is <jdevhome>\bc4j\src\bc4jhtmlsrc.zip!\oracle\jbo\http\HttpSessionCookieImpl.java.
    I'm guessing that somewhere in the project there's an xml file that has an out-of-date reference to a file location that doesn't exist on this computer. Can anyone point me in the right direction? I'm a bit concerned that JDev projects are dependent upon the original computer? Please say it isn't so!

    Thanks,
    Ive set this, although the temporary files that Reports usese are going there, the temp PDF isnt!!

  • HP DESKJET INK ADVANT K209a-z, extraction fialed : error message "0 cannot open output file"

    D/Sir,
    I have extracted hp deskjet int advant k209a-z driver using 7zip.
    I was getting the error "Extraction Failed: Cannot Open Output File".  
    On extract with 7-zip, I get the message: 
        0 can not open output file "<folders>/Autorun.inf" 
    I am on business laptop with Windows XP but tried with Admininstrator login as well.
    Please help me. How to extract it sucessfully?

    That type of error message may be indicative of a bad file. Did you download it on the web? If so, try again, but do not use a download manager or program to do it, those can occasionally cause problems with compressed files.
    It could be possible, also, that some sort of security program on your laptop is blocking the extraction process. If that is the case you should be able to find some error in the Windows event viewer through the control panel.
    007OHMSS
    I was a support engineer for HP.
    If the advice resolved the situation, please mark it as a solution. Thank you.

  • When I try to download firefox I get this error "cannot open output file". I had firefox once but uninstalled it now I cant' reinstall. Why?

    I had firefox but uninstalled it because of problems with add on Recipefox. Now when I try to reinstall it I get and error message "cannot open output file". I really liked firefox, How do I get it back?

    When you click the download link on [http://getfirefox.com GetFirefox.com], you should be asked if you wish to Run or Save the file. If the described situation happens when trying to Run the download, try instead to Save it and put the file on your Desktop or a similar place where you are certain that you can find it again.
    When the download is complete, try double-clicking the downloaded file in the normal Windows Explorer (browse your way to the file from My Computer). This should start the installation.
    If you notice in the Explorer window that the file seems to be lacking the Firefox orange/blue icon, rightclick the file and select Properties. The picture should look somewhat like the attached picture (except that mine's in danish, but that is irrelevant) if saved correctly - if it does NOT look like this, please describe the contents or attach a screenshot of the box. Especially what it says under "File type" - it should be "Program"; if it's not, we'll have to look into what the problem could be here.
    Slightly off-topic, your Internet Explorer seems to be quite a bit out of date (IE 6, where current version is IE 8), so I would strongly recommend that you try to run Windows Update to get your system updated. If this is a company system (like a Terminal Server thin client machine), this may not be possible, and your system administrator will most likely have to help you.

Maybe you are looking for