DAQmx device not showing in LabView 2009

Hi
I have a USB-6501 that im trying to use with LabView 2009. It is installed and shows up in MAX however when i try to access it through LabView its not listed when i try to set the physical channel of the DAQms create channel vi. The entire device is missing.
Anyone had this problem or have an idea what im doing wrong?
Solved!
Go to Solution.

As i thought.... your physical channel constant is filtered for AI only. Please change it by rightclicking on it and select "IO Name Filtering...".
In the dialog, change the IO Type to Digital Input. Now you should find the 65xx device.
Note that the setting for the IO Filtering is determined when creating the constant/control. So if you created it when the DAQmx Create Channel was configured to AI Voltage (Default), the IO Name Filtering is AI. This will not change just because you reconfigure the DAQmx Create Channel.....
Norbert
CEO: What exactly is stopping us from doing this?
Expert: Geometry
Marketing Manager: Just ignore it.

Similar Messages

Device NOT showing up on my monitor when plugged in?

Iphone plugged in.
Device not showing up? Any ideas?

You're welcome.
This link applies to a Mac.
http://support.apple.com/kb/ts1591

Devices not showing up on I-pod, how to disconnect safely?

devices not showing up on I tunes for I pod, how to disconnect I pod safely

I fixed the problem on my own , hey I'm a genius!! I clicked on my i-pod tab on the left column in i tunes and where the options for podcast tab is just changed the sync option to all podcasts instead of last looked at. Now i have all my podcasts in the video podcast menu on my i pod.

Device not showing in iTunes for 'Wi-Fi Sync' and 'Sync Now' on phone only works(appears dark) when plugged in via USB so kinda defeats object. Any ideas please?

Device not showing in iTunes for 'Wi-Fi Sync' and 'Sync Now' on phone only works(appears dark) when plugged in via USB so kinda defeats object. Any ideas please?

Had the same issue. Tried everything that was posted for troubleshooting bye apple and on the discussions.
Finally, tried something that solved it and it works flawlessly now. I changed my wireless router.
I was using my ISP's supplied ZyXEL PN660 ADLS2+ with Wireless N. Swtiched to an older Linksys WRT160N and it is working beautifully now.
Take a look at your router, make sure the firmware is up to date, and that UPnP is enabled, and if all is correct, and you have done everything else, try another Wireless router if you can.

Firewire device not showing

Greetings
using a G5, tiger 10.4.9
I have been using this computer for many months with no problem using firewire devices. I recently set up a seperate user account on the computer for my daughter. Prior to this ( for many months)I had a fireiwre device - LACIE external HD -connected that would mount each time at startup and show up on the desktop. Now, I can't get the icon on the desktop of the LACIE to show when I startup. I connected a camera to the computer using firewire, but it too would not show ( before it would). When I connected the camera using USB, it showed up on the desktop. Looks like firewire devices not showing. I checkd System Profile and it shows the LACIE device as connected and functioning. But it won't show up on the desktop. Any ideas on why I can't ge the Firewire devices to show on the desktop?
Thank you in advance for you help. . . .
Brian
G5 Dual 2.7 Mac OS X (10.4)
G5 Dual 2.7 Mac OS X (10.4)
G5 Dual 2.7 Mac OS X (10.4)
G5 Dual 2.7 Mac OS X (10.4)

Sounds like you have the name wrong. Open Disk Utility and take a look to verify the volume name. Disk Utility will list the drive itself, then indented below that is the volume name. To verify that you are using the correct name, try launching Terminal and do a list command:
ls -a /Volumes/"Name of Volume"
Hit the return key and see if the contents of the volume are listed. There is a space after "ls" and another after "-a"--if you don't get anything or get an error then you might want to try
ls -a /Volumes
and try copying the name from the list and pasting into the AppleScript.
Francine
Francine
Schwieder

Why does new music downloaded on one device not show up in the library of the other device?, Why does new music downloaded on one device not show up in the library of the other device?

Why does new music purchased on one device not show up in the library of the other?

Hi Bev5638,
Welcome to the Support Communities!
The article below will explain how to set up Automatic Downloads for your computer and devices.
iTunes Store: How to enable Automatic Downloads
http://support.apple.com/kb/ht4539
Cheers,
- Judy

HT6337 Allow handoff between this mac and your iCloud devices not showing up in general preferences

Is anyone not seeing this? the Allow handoff between this mac and your iCloud devices not showing up in general preferences
Imac 2011 21" mid 2011

nevermind, Just figured out that my iMac does not support it. Thanks Apple, once again coming up with stupid functionality that only works when you pay more money. 3yr old machine, I guess I need to send it to scrap heap.

Devices not showing in Max

I just tried to install a USB-6251 in my Laptop (Toshiba Tecra S2). The units is detected and the driver installs. It shows up in the device manager as a properly installed device. However, MAX does not show the device. The Laptop has WInXP-Pro, 2GB RAM and LV 8.20.
When I tried the same thing on my desktop, the 6251 installed in the same way, and then the option to run Test Panels showed up and the
unit ran happily.
Incidentally, I have a minor problem with a PCMCIA 6024 which takes a long time to show up under DAQmx in Max, and a PCMCIA -16E4 which insists on showing up under DAQmx as a 6024 (16E4 is not supported by DAQmx). Both show up promptly and work fine under traditional DAQ.
I suspect there is some problem in the device registration part of the WinXP - NI interface. These boards do not list under the add-remove hardware icon either.
Thanks in advance
Sanjay Gupta
Chief Scientific Officer & Ex-Head
Advanced Centre for Materials Science
Indian Institute of Technology
Kanpur 208016
Phones: +91-512-2597830, 3927830(Off), 2574628 (Res), 9336117477 (Mob)
Fax: +91-512-2597459
E-mail: [email protected], [email protected], http://home.iitk.ac.in/~sg

David,
Things have gone from bad to worse. I tried the upgrade in the Laptop with no success, and now the desktop is also playing up.
I have a ner full installation of the Academic Site License- PDS, RT, RIO ... (the works) on both my systems, as I am a regular user of cRIO for almost 1-1/2 years:
The Laptop story now:
1. After upgrading to 8.50 (no problems in the install), MAX still not ssing anything.
2. I tried to close the Configuration Manager it did not even do that. One process (I think mxssvr) did not close.
3. Tried removing MAX. Removed a lot of other things, incl. LabVIEW.
4. Removed the entire NI Install. Removed all NI directories in Program Files, Documents and settings > ... etc. Also, the FPGA directories in c:\ etc.
5. Using Regedit cleaned up virtually all National Instruments entries in the Registry. In otehr words removed all traces of NI software I could.
6. Reinstalled LabVIEW .....
7. Reactivated everything.
8. MAX (4.1) still not working
9. Checked in Admin Tools > Services. Found Configuration Manager and nidevldu not active.
10. Tried to start them. Config Manager does not start (Error 1067: The process terminated unexpectedly). nidevldu does start if started manually.
The Desktop:
1. Everything was fine.
2. Upgraded to DAQmx 8.50 incl MAX 4.2.
3. Now MAX does not work.
4. Admin > Services shows both processes running.
5. Still to try to shut down and manually try and clean up Data.
6. I was looking at some examination solutions and was able to run code (LV legacy) in LV. Could not try out DAQmx as could not do the easy reset from MAX.
I may add that the Laptop has had LV 7.1 (also possibly 7.0), 8.0 (incl. beta), and 8.2! The desktop did not have the 8.0's.
Any ideas! What do I do now. I always have the option of reformatting drive C and starting from scratch, but am loathe to do so. Will take a full working day at least.
Thanks
Sanjay.
Chief Scientific Officer & Ex-Head
Advanced Centre for Materials Science
Indian Institute of Technology
Kanpur 208016
Phones: +91-512-2597830, 3927830(Off), 2574628 (Res), 9336117477 (Mob)
Fax: +91-512-2597459
E-mail: [email protected], [email protected], http://home.iitk.ac.in/~sg

DAQmx devices not recognized after reboot

I have a PXI-1042 box communicating with a desktop computer over a MXI-3 bridge. This system has been up and running for several years through four or five revs of code. I am currently running MAX 4.6.0f1, DAQmx 8.9.5, LV 2009 and TS 4.2.
Lately when an engineer logs on, although all six cards are recognized in the NI-DAQmx Devices configuration section, only three are listed as installed. All six cards are listed in the Chassis section. See attached screen shot. If the engineer logs out and reboots enough times, eventually all six cards are available. Any ideas on what may be corrupting the configuration?
The PC is a Dell Precision WorkStation 380 (Pentium 4) running XP SP3 with 4 GB of memory. The installed PXI cards are:
Slot        Card
1            8330 MXI-3
2            2567 Relay Control
3            6551 DIO
4            6551 DIO
5            2503 Mux
6            6220 M series DAQ
7            2591 Coax Mux
Thanks, Bob
Attachments:
MAX NI-DAQmx issue.JPG ‏83 KB

John,
Here are answers to most of your questions:
Can you verify that the missing switch modules are always only the switch modules, or are other modules sometimes missing, too?
           >> It is always the switch modules that are missing.
Is the MXI Bridge always connected to the host controller?
Is the chassis always powered up before the host?
           >> Yes and yes.
When the engineer repeatedly logs out and in, do the cards appear only one at a time, or do multiple formerly missing cards appear at once?
           >> They always come and go together.
Once all cards appear in MAX, do they remain until the machine reboots (even if you log out or in)?
           >> Not positive on this one. I'm 90% sure they come and go, even with just logging in and out.
When cards are missing, does the device manager list the cards under the NI Devices section, or are there any bangs?
           >> Not sure what you are asking here. Is this the "NI-DAQmx Devices" section that is highlighted in the screen shot? The center panel is what is listed when this section header is selected (as shown). What are "bangs"?
Thanks for your help
Bob

Lion 10.7.2 / iTunes 10.5 - Devices not showing up

Any device attached via USB is not showing up in iTunes. I have the following ipad2, iphone 3gs and itouch (latest gen)
USB connections are working as ipad2 and itouch devices show up in iPhoto.
I have a Mac Pro Early 2008 version.
I've tried the following:
1) switching USB ports on my Mac Pro
2) rebooting Mac Pro leaving devices powered on
3) rebooting devices leaving Mac Pro on
4) turning everything off, and booting Mac Pro first. waiting 2minutes and then powering on ipad2, iphone, itouch
Nothing seems to work. Hoping someone else is stuck in the same spot or can advise next steps.
Thanks,
Nick

So far the only solution I have been able to find has been launching the recovery partition and running disk repair. That will fix the problem until you trigger it again. Fortunately, or unfortunately, I have pinpointed what triggers it on my computer.
Seems to be a flaw in keychain access. When Safari's connection times out due to an expired certificate (common in university networks that require a log in every few hours), the security settings freak out and effectively shut down safari's ability to do anything. The fact that it attacks KeyChain access and iPhoto and more is just a really big system wide glitch. Here's the run down:
http://digit.algravitas.com/2011/10/major-networking-glitch-found-in-os-x-v10-7- 2/

Network devices not showing up under "shared" in finder bar

Ok so i have a network that consists of a maxtor nas device, 2 win xp pc's, 1 win7 pc, d-link 524 router, and my macbook pro. I would like to be able to transfer files between my mac and the devices and use the printer attached to my maxtor. My issue is that none of the computers show up under the "shared" section of finder or under network. I use to have this issue with leopard but it resolved itself. Now under snow leopard for a couple months and i have yet to get it work. I can access my mac and other pcs from a pc. Anyone know how to get my network to show up on my mac?

Your problem is very common under Snow. At first my shares did not show up under shared in finder windows. I, then, of course, used "Connect to Server" to connect to the shares--both Mac and PC. I found that the more I kept the shares active the more likely they were show up under shared. Then, I discovered that if I kept the computers from sleeping during the period of needed access they would tend to stay in shared without nearly so much keeping the connections active.
If you do not like the above work around, then there are two other possibilities. You can elect to show mounted items on your desktop. Do that and connect to each share. Then, go > users > unlock > + login options > try dragging the mounted shares to the login item window. If successful, then the shares should be available at login.
Another approach is to mount and connect as indicated above. Then, making an alias to the share should at least make things faster.

Shared devices not showing up in finder

Shared devices on my network are not showing up in Finder on my MacBook Air. Problem just began in the last 24 hours, and is limited to just this computer. Have done usual things -- checking, unchecking shared devices in Finder; relaunching Finder; restarting computer. Any ideas?

Your problem is very common under Snow. At first my shares did not show up under shared in finder windows. I, then, of course, used "Connect to Server" to connect to the shares--both Mac and PC. I found that the more I kept the shares active the more likely they were show up under shared. Then, I discovered that if I kept the computers from sleeping during the period of needed access they would tend to stay in shared without nearly so much keeping the connections active.
If you do not like the above work around, then there are two other possibilities. You can elect to show mounted items on your desktop. Do that and connect to each share. Then, go > users > unlock > + login options > try dragging the mounted shares to the login item window. If successful, then the shares should be available at login.
Another approach is to mount and connect as indicated above. Then, making an alias to the share should at least make things faster.

EA4500 Router Device not showing up in device list - Please Help

Hi all
I have an EA4500 and am using Cisco Connect Cloud software. Its working mostly fine except that I have one device on the network that will not show up in the device list. This is not an issue in itself and normally I would ignore (although it used to show up when I forst got the router) however.......
The device is a WDTVLive media unit and required access to windows shares on a media server. Now the WDTVLive device is server an ip address by the router and is available from everywhere on my network but every couple of days it loses the capacity to search windows shares.
I know what you are thinking and I initially thought the same, this is an issue with the WDTVLive box. However one day I spent a few hours trying to resolve (Am an IT Consultant and know a little about networks) and found that I could not fix the issue. I then rebooted the router and it started working. I have since confirmed that every time it breaks I have to reboot the router.
So I kind of think the two issues are linked.
Sorry for the ramble. Can anyone help please.
Thanks in advance
Alan

Further to this issue which I ignored as it did not really cause any issues, I recently clicked a samsung tv device which thinks that is three different devices. It has three lan addresses listed. One of the addresses listed is the original device that will not show up so I suspect that this is why it does not show up.
It seems that I have a conflict but I can find nothing anywhere to allow me to resolve.
I cannot even delete the Samsung TV device as its x button is not editable.
Should I just try removing the cloud connect software. I must admit that I am starting to think that I made a bad decision with this router.
Any help would be greatly appreciated

Successfully enrolled devices not showing in profile manager

On a newly installed (from scratch, formatted etc) Mountain Lion server, I'm having an issue where I can successfully enrol a device, an iPhone with 6.1 iOS in this case, but the enrolled device does not show up in the devices?
I see a previous post in these communities with a similar issue, the solution was to add place holders after the device was enrolled, unfortunately this is not a solution for me, as soon as you re-enrol the placeholder dissapears I have another server running mountain lion at another site and this is working just fine.
Any solutions? I'm pulling my hair out with this. I have a niggling feeling that with the other server I had a similar problem when I upgraded to Mountain Lion and had to edit one of the ruby files in the profilemanager to display the devices but I can't remember where or when
Regards,
Stephen...

ok update to this problem:
If I enroll a Mac device, in this case the mini server itself then these are displayed under the device library.
also tried an iPad with iOS6 and this was successful, and displays in the device library.
Currently the iPhone is not displaying although enrolled successfully is an iPhone4 so I'm going to experiment with a few other devices and see whats happening

Devices not showing up in CM

Sometimes all my devices show up int he CM, other times not, when they do not show, I have to "search" for them by the exact name.
We have redunsant CM's and I wonder if this could be some sync issue, or if there is something wrong with my user.
Othwer users on the CM do not experience this problem (to my knowledge)
Best regards
Ole

Hi Ole,
Looks like a bug. Has this happened after upgrading a browser or making any changes to the CM or after deleting a WAE device from CM? There is a known issue where after deleting a WAE device CM page doesn't show any devices. Reload of the CM resolves the issue.
CSCtu31886: No Data shown after deleting WAE from CM
A permanent software fix for this defect is in 5.0.1 and higher. The workaround is to
reload the CM.
Regards,
Kanwal

DAQmx device not showing in LabView 2009

Similar Messages

Maybe you are looking for