DASYLab data output stopping after 10 points
Let me preface everything by saying I'm a novice at this. Now that that's out of the way...
I am having an issue getting more than 10 data points to record into an output file. I'm sure it's some setting conflict but I'm having no luck figuring it out.
I've got two tasks in Measurement & Automation Explorer: the first recording 4 strain gage signals, the second recording 2 temperature signals. The strain gage signals are coming into a NI 9237 and the thermocouples are coming into a NI 9211; both seated in a NI cDAQ-9188.
In DASYLab (v13) I have the setup shown in the attached image:
When I click Play everything seems to run fine (i.e., no error messages), but when I stop and open up the generated ASC file there are only 10 data points, one point every 0.1 second for 1 second.
Can anyone point me in the direction of the settings that control data collection, either in DASYLab or in M&AE? Thanks!
Solved!
Go to Solution.
Thanks for responding so quickly!
As I was typing up a response I noticed something in the Timing Settings in the M&AE tasks. The Acquistion Mode was set to 'N Samples'. I changed the mode to 'continuous samples' and it is now recording as I was expecting. I'm still not sure what was defining the "N" as 10, because the Samples to Read was set to 10k, but since it now seems to be working I'll leave that to another day. Thanks again
Similar Messages
-
Concerning: VGA monitors using an Aluminum Powerbook G4 PowerPC 2004 15"-screen 1.5Ghz
The DVI (converted to VGA) video output stopped working on this computer after 9 years of service. This raises question 1:
Is there any way of fixing this? I've tried the usual: triple checked all vga cables & devices through trial & error. Bought a new DVI-VGA adapter. Reset PRAM, PMU, etc. Nothing works. Something is probably damaged, because my KVM switch was not working unless I hot-reseated the vga cable into it, leading to this DVI port, and that is pretty rough stuff.
Question 2 (related):
This dovetails into this: Can I drive a VGA monitor with the s-video output port on this computer. It would take an s-video (male)-to-15-pin-VGA adapter. Has anyone does this? So far, I haven't even found the adapter mentioned anywhere.
Thanks for reading this.
el7Thanks for the useful feedback, Knucklesmac. I agree. I must have blown something on the logic board -- because I had a faulty old KVM switch that would not switch between computers without some nasty hot-plugging/unplugging the VGA video cables. (wince!). It's like when Dizzy Dean ruined his arm because a line drive hit him in the foot and he readjusted his mechanics around the injury. I take the blame because this has been a great computer, and does not deserve any blame.
If it will help anyone else reading this thread, C2G (née Cables to Go) has some interesting ideas for still getting external video out of this computer:
-USB-to-VGA
http://www.cablestogo.com/product/30545
-Convert s-video or composite video signals to high resolution VGA
http://www.cablestogo.com/product/40971
The price range is $75-$85, which doesn't make horse sense to me for such an old computer -- which has a lot of life in it anyway, because its own 15" monitor is not chopped liver.
el7 -
Data services stop working after updating to new OS version for Q10
I am from Qatar, after i updated my device ( Q10 SNQ100-3 ) to new OS ( 10.2.1.537 ), the mobile data services stopped working, but it works everytime I connect to wifi. This is the same with Z10. Please need help.
Hi and Welcome to the Community!
With a strong carrier network signal (e.g., not merely WiFi), I suggest the following steps, in order, even if they seem redundant to what you have already tried (step 1 should result in a message coming to your BB...please wait for that before proceeding to the next step):
1) Register HRT
KB00510 How to register a BlackBerry smartphone with the wireless network
Please wait for one "registration" message to arrive
2) Reboot
Pre-BB10 Devices ONLY. With power ON, remove the back cover and pull out the battery. Wait about a minute then replace the battery and cover. Power up and wait patiently through the long reboot -- ~5 minutes.
BB10 Devices. Hold the top button down until the counter reaches zero. Wait for the device to be fully shut down (e.g., nothing at all displayed on the screen, no LED lights, etc.). Hold the top button until the red LED is lit. Wait through the full boot-up process. IF this fails, you can attempt the battery-pull method above, but it is normally NOT recommended unless nothing else works.
See if things have returned to good operation. Like all computing devices, BB's suffer from memory leaks and such...with a hard reboot being the best cure.
Hopefully that will get things going again for you! If not, then you should contact your mobile service provider for formal support.
Good luck!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code -
on an pci_mio 16e4 programming using nidaq & visual basic, after using AI_Setup analog sequential data accusition stops.To restart I use Init_DA_Brds This takes a long time, What must I reset to restore the analog sequential function?
I belive that the trigger is being changed on the io board, but cannot manage to reset it.
The reset process takes in the order of 0.1 sec, and since this is a time critical application, i want to get the scanning function working again fasterDear Ian. Thank you for your reply. The problem appears to be that the scan trigger(s) are stopped, or something, by the use of the AI_setup instruction. The sytstem works perfectly until this instruction is used. My problem is in understanding what has happened since the help seems to give no detail on any interconnection between the scan system and the external analog trigger system. I have tried to reconnect the triggers, but so far unsucessfuly
-
Headphone output stopped working (snd-hda, Dell XPS 13)
Update: I got it working! See my second post; I will leave this here as a reference for those with the same problem.
My headphone output stopped working, and my integrated microphone also stopped working. The speakers work fine, though.
AFAIK, I didn't do anything, and am quite baffled as to why this is. It's worked fine for half a year.
I have a Dell XPS 13; it came installed with Ubuntu, I booted that, where it *does* work (just to eliminate hardware problems).
I'm running 3.16.4-1; I also downgraded to 3.16.3, which didn't help.
I'm testing with speaker-test and mplayer -ao alsa; I normally use PulseAudio, but eliminating that for testing seemed like a sane thing to do. It doesn't work either way.
I also downloaded the hda_analyzer, that has a lot of options, but I'm not sure what most of them mean...
The closest I've been able to get at the problem is this:
[~]% alsactl monitor
card 0, #17 (0,0,0,Headphone Mic Jack,0) VALUE
card 0, #17 (0,0,0,Headphone Mic Jack,0) VALUE
This is an insert & remove of my headphone jack; ALSA does detect something it seems. It's listed as "Headphone Mic Jack", is this right?
Any hints would be greatly appreciated!
More info:
[~]% cat /etc/modprobe.d/alsa-base.conf
options snd-hda-intel enable=0,1
options snd-hda-intel model=dell-headset-multi,dell-headset-multi
This is required to get this to work in the first place, and always has worked; I tried some other options, to no avail. the enable=0,1 is to disable the HDMI output (disabling this has no effect either).
$ cat /sys/module/snd_hda_intel/parameters/model
dell-headset-multi,dell-headset-multi,(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null), +(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)
To verify these options are actually being used
$ id -Gn
martin wheel video audio vboxusers nfs
I'm in the audio group, not sure if this is required, but can't hurt.
[~]# cat /etc/asound.conf
# Use PulseAudio by default
pcm.!default {
type pulse
fallback "sysdefault"
hint {
show on
description "Default ALSA Output (currently PulseAudio Sound Server)"
ctl.!default {
type pulse
fallback "sysdefault"
# vim:set ft=alsaconf:
Nothing special ... pulseaudio is more or less mandatory these days. ~/.asoundrc doesn't exist.
Some misc. info:
$ grep Codec /proc/asound/card*/codec*
Codec: Realtek ALC3661
[~]% lsmod | grep ^snd
snd_usb_audio 135316 0
snd_usbmidi_lib 27484 1 snd_usb_audio
snd_rawmidi 26806 1 snd_usbmidi_lib
snd_seq_device 13132 1 snd_rawmidi
snd_hda_codec_realtek 67127 1
snd_hda_codec_generic 63126 1 snd_hda_codec_realtek
snd_hda_intel 26327 3
snd_hda_controller 26727 1 snd_hda_intel
snd_hda_codec 108552 4 snd_hda_codec_realtek,snd_hda_codec_generic,snd_hda_intel,snd_hda_controller
snd_hwdep 17244 2 snd_usb_audio,snd_hda_codec
snd_pcm 88487 4 snd_usb_audio,snd_hda_codec,snd_hda_intel,snd_hda_controller
snd_timer 26614 1 snd_pcm
snd 73436 17 snd_hda_codec_realtek,snd_usb_audio,snd_hwdep,snd_timer,snd_pcm,snd_rawmidi,snd_hda_codec_generic,snd_usbmidi_lib,snd_hda_codec,snd_hda_intel,snd_seq_device
$ lspci -vv
00:03.0 Audio device: Intel Corporation Haswell-ULT HD Audio Controller (rev 09)
Subsystem: Dell Device 060a
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f0510000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel modules: snd_hda_intel
00:1b.0 Audio device: Intel Corporation 8 Series HD Audio Controller (rev 04)
Subsystem: Dell Device 060a
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 59
Region 0: Memory at f0514000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
$ dmesg
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.16.4-1-ARCH (nobody@var-lib-archbuild-testing-x86_64-tobias) (gcc version 4.9.1 20140903 (prerelease) (GCC) ) #1 SMP PREEMPT Mon Oct 6 08:22:27 CEST 2014
[ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=7259ebb8-c940-4659-a99c-66226a58659c rw quiet
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009cfff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009d000-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000c2879fff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000c287a000-0x00000000dceeefff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000dceef000-0x00000000dcf9efff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000dcf9f000-0x00000000dcffefff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x00000000dcfff000-0x00000000df9fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000f8000000-0x00000000fbffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fe101000-0x00000000fe112fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed08000-0x00000000fed08fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed10000-0x00000000fed19fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ff980000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000021f5fffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] SMBIOS 2.7 present.
[ 0.000000] DMI: Dell Inc. XPS13 9333/0GFTRT, BIOS A02 12/11/2013
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] AGP: No AGP bridge found
[ 0.000000] e820: last_pfn = 0x21f600 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: write-back
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 00E0000000 mask 7FE0000000 uncachable
[ 0.000000] 1 base 00DE000000 mask 7FFE000000 uncachable
[ 0.000000] 2 base 00DD000000 mask 7FFF000000 uncachable
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] 8 disabled
[ 0.000000] 9 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] e820: last_pfn = 0xc287a max_arch_pfn = 0x400000000
[ 0.000000] found SMP MP-table at [mem 0x000f0100-0x000f010f] mapped at [ffff8800000f0100]
[ 0.000000] Scanning 1 areas for low memory corruption
[ 0.000000] Base memory trampoline at [ffff880000097000] 97000 size 24576
[ 0.000000] Using GB pages for direct mapping
[ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[ 0.000000] [mem 0x00000000-0x000fffff] page 4k
[ 0.000000] BRK [0x01b23000, 0x01b23fff] PGTABLE
[ 0.000000] BRK [0x01b24000, 0x01b24fff] PGTABLE
[ 0.000000] BRK [0x01b25000, 0x01b25fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x21f400000-0x21f5fffff]
[ 0.000000] [mem 0x21f400000-0x21f5fffff] page 2M
[ 0.000000] BRK [0x01b26000, 0x01b26fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x21c000000-0x21f3fffff]
[ 0.000000] [mem 0x21c000000-0x21f3fffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x200000000-0x21bffffff]
[ 0.000000] [mem 0x200000000-0x21bffffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x00100000-0xc2879fff]
[ 0.000000] [mem 0x00100000-0x001fffff] page 4k
[ 0.000000] [mem 0x00200000-0x3fffffff] page 2M
[ 0.000000] [mem 0x40000000-0xbfffffff] page 1G
[ 0.000000] [mem 0xc0000000-0xc27fffff] page 2M
[ 0.000000] [mem 0xc2800000-0xc2879fff] page 4k
[ 0.000000] init_memory_mapping: [mem 0x100000000-0x1ffffffff]
[ 0.000000] [mem 0x100000000-0x1ffffffff] page 1G
[ 0.000000] RAMDISK: [mem 0x3796a000-0x37cacfff]
[ 0.000000] ACPI: Early table checksum verification disabled
[ 0.000000] ACPI: RSDP 0x00000000000F0120 000024 (v02 DELL )
[ 0.000000] ACPI: XSDT 0x00000000DCFFE170 0000BC (v01 DELL QA09 00000002 LOHR 00000002)
[ 0.000000] ACPI: FACP 0x00000000DCFFB000 00010C (v05 DELL QA09 00000002 LOHR 00000002)
[ 0.000000] ACPI: DSDT 0x00000000DCFE6000 010557 (v02 DELL HSW-LPT 00000000 INTL 20120711)
[ 0.000000] ACPI: FACS 0x00000000DCF9C000 000040
[ 0.000000] ACPI: ASF! 0x00000000DCFFD000 0000A5 (v32 DELL QA09 00000002 LOHR 00000002)
[ 0.000000] ACPI: HPET 0x00000000DCFFA000 000038 (v01 DELL QA09 00000002 LOHR 00000002)
[ 0.000000] ACPI: LPIT 0x00000000DCFF9000 000094 (v01 DELL QA09 00000002 LOHR 00000002)
[ 0.000000] ACPI: APIC 0x00000000DCFF8000 000098 (v01 DELL QA09 00000002 LOHR 00000002)
[ 0.000000] ACPI: MCFG 0x00000000DCFF7000 00003C (v01 DELL QA09 00000002 LOHR 00000002)
[ 0.000000] ACPI: SSDT 0x00000000DCFE5000 000228 (v01 DELL sensrhub 00000000 INTL 20120711)
[ 0.000000] ACPI: SSDT 0x00000000DCFE2000 002028 (v01 DELL PtidDevc 00001000 INTL 20120711)
[ 0.000000] ACPI: SSDT 0x00000000DCFE1000 000539 (v01 DELL Cpu0Ist 00003000 INTL 20120711)
[ 0.000000] ACPI: SSDT 0x00000000DCFE0000 000AD8 (v01 DELL CpuPm 00003000 INTL 20120711)
[ 0.000000] ACPI: SSDT 0x00000000DCFDC000 003641 (v01 DELL SaSsdt 00003000 INTL 20120711)
[ 0.000000] ACPI: UEFI 0x00000000DCFDB000 000042 (v01 DELL QA09 00000002 LOHR 00000002)
[ 0.000000] ACPI: POAT 0x00000000DCF77000 000055 (v03 DELL QA09 00000002 LOHR 00000002)
[ 0.000000] ACPI: BATB 0x00000000DCFDA000 000046 (v01 DELL QA09 00000002 LOHR 00000002)
[ 0.000000] ACPI: FPDT 0x00000000DCFD9000 000064 (v01 DELL QA09 00000002 LOHR 00000002)
[ 0.000000] ACPI: SLIC 0x00000000DCFD8000 000176 (v01 DELL QA09 00000002 LOHR 00000002)
[ 0.000000] ACPI: UEFI 0x00000000DCFD7000 0002A6 (v01 DELL QA09 00000002 LOHR 00000002)
[ 0.000000] ACPI: SSDT 0x00000000DCFD6000 0005C1 (v01 DELL IsctTabl 00001000 INTL 20120711)
[ 0.000000] ACPI: CSRT 0x00000000DCFD4000 0000C4 (v01 DELL QA09 00000002 LOHR 00000002)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000021f5fffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x21f5fffff]
[ 0.000000] NODE_DATA [mem 0x21f5f9000-0x21f5fdfff]
[ 0.000000] [ffffea0000000000-ffffea00087fffff] PMD -> [ffff880217200000-ffff88021ebfffff] on node 0
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00001000-0x00ffffff]
[ 0.000000] DMA32 [mem 0x01000000-0xffffffff]
[ 0.000000] Normal [mem 0x100000000-0x21f5fffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00001000-0x0009cfff]
[ 0.000000] node 0: [mem 0x00100000-0xc2879fff]
[ 0.000000] node 0: [mem 0x100000000-0x21f5fffff]
[ 0.000000] On node 0 totalpages: 1973782
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 21 pages reserved
[ 0.000000] DMA zone: 3996 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 12386 pages used for memmap
[ 0.000000] DMA32 zone: 792698 pages, LIFO batch:31
[ 0.000000] Normal zone: 18392 pages used for memmap
[ 0.000000] Normal zone: 1177088 pages, LIFO batch:31
[ 0.000000] Reserving Intel graphics stolen memory at 0xdda00000-0xdf9fffff
[ 0.000000] ACPI: PM-Timer IO Port: 0x1808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-39
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a301 base: 0xfed00000
[ 0.000000] smpboot: Allowing 8 CPUs, 4 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 56
[ 0.000000] PM: Registered nosave memory: [mem 0x0009d000-0x0009ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000dffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000e0000-0x000fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xc287a000-0xdceeefff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdceef000-0xdcf9efff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdcf9f000-0xdcffefff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdcfff000-0xdf9fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdfa00000-0xf7ffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xf8000000-0xfbffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfc000000-0xfe100fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfe101000-0xfe112fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfe113000-0xfebfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec01000-0xfed07fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed08000-0xfed08fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed09000-0xfed0ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed10000-0xfed19fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed1a000-0xfed1bfff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed1c000-0xfed1ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed20000-0xfedfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfee00000-0xfee00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfee01000-0xff97ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xff980000-0xffffffff]
[ 0.000000] e820: [mem 0xdfa00000-0xf7ffffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:128 nr_cpumask_bits:128 nr_cpu_ids:8 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 29 pages/cpu @ffff88021f200000 s86784 r8192 d23808 u262144
[ 0.000000] pcpu-alloc: s86784 r8192 d23808 u262144 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1942919
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=7259ebb8-c940-4659-a99c-66226a58659c rw quiet
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] xsave: enabled xstate_bv 0x7, cntxt size 0x340
[ 0.000000] AGP: Checking aperture...
[ 0.000000] AGP: No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 7688084K/7895128K available (5336K kernel code, 887K rwdata, 1688K rodata, 1128K init, 1164K bss, 207044K reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[ 0.000000] RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=8.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8
[ 0.000000] NR_IRQS:8448 nr_irqs:1016 16
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] allocated 31981568 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] hpet clockevent registered
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] tsc: Detected 2394.295 MHz processor
[ 0.000039] Calibrating delay loop (skipped), value calculated using timer frequency.. 4790.11 BogoMIPS (lpj=7980983)
[ 0.000042] pid_max: default: 32768 minimum: 301
[ 0.000050] ACPI: Core revision 20140424
[ 0.020000] ACPI: All ACPI Tables successfully acquired
[ 0.020260] Security Framework initialized
[ 0.020267] Yama: becoming mindful.
[ 0.020937] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[ 0.022978] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.023836] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.023849] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.024116] Initializing cgroup subsys memory
[ 0.024140] Initializing cgroup subsys devices
[ 0.024147] Initializing cgroup subsys freezer
[ 0.024150] Initializing cgroup subsys net_cls
[ 0.024155] Initializing cgroup subsys blkio
[ 0.024183] CPU: Physical Processor ID: 0
[ 0.024184] CPU: Processor Core ID: 0
[ 0.024189] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
[ 0.025376] mce: CPU supports 7 MCE banks
[ 0.025391] CPU0: Thermal monitoring enabled (TM1)
[ 0.025404] Last level iTLB entries: 4KB 1024, 2MB 1024, 4MB 1024
Last level dTLB entries: 4KB 1024, 2MB 1024, 4MB 1024, 1GB 4
tlb_flushall_shift: 6
[ 0.025524] Freeing SMP alternatives memory: 20K (ffffffff819f9000 - ffffffff819fe000)
[ 0.026475] ftrace: allocating 20445 entries in 80 pages
[ 0.038058] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.071090] smpboot: CPU0: Intel(R) Core(TM) i7-4500U CPU @ 1.80GHz (fam: 06, model: 45, stepping: 01)
[ 0.071098] TSC deadline timer enabled
[ 0.071124] Performance Events: PEBS fmt2+, 16-deep LBR, Haswell events, full-width counters, Intel PMU driver.
[ 0.071149] ... version: 3
[ 0.071150] ... bit width: 48
[ 0.071151] ... generic registers: 4
[ 0.071152] ... value mask: 0000ffffffffffff
[ 0.071154] ... max period: 0000ffffffffffff
[ 0.071155] ... fixed-purpose events: 3
[ 0.071156] ... event mask: 000000070000000f
[ 0.097907] x86: Booting SMP configuration:
[ 0.097909] .... node #0, CPUs: #1
[ 0.112630] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[ 0.119293] #2 #3
[ 0.154938] x86: Booted up 1 node, 4 CPUs
[ 0.154942] smpboot: Total of 4 processors activated (19162.45 BogoMIPS)
[ 0.160676] devtmpfs: initialized
[ 0.163608] PM: Registering ACPI NVS region [mem 0xdceef000-0xdcf9efff] (720896 bytes)
[ 0.164642] pinctrl core: initialized pinctrl subsystem
[ 0.164688] RTC time: 22:42:27, date: 10/21/14
[ 0.164750] NET: Registered protocol family 16
[ 0.164884] cpuidle: using governor ladder
[ 0.164887] cpuidle: using governor menu
[ 0.164916] ACPI: bus type PCI registered
[ 0.164918] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.165012] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
[ 0.165014] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
[ 0.165118] PCI: Using configuration type 1 for base access
[ 0.165125] dmi type 0xB1 record - unknown flag
[ 0.177572] ACPI: Added _OSI(Module Device)
[ 0.177575] ACPI: Added _OSI(Processor Device)
[ 0.177577] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.177578] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.183007] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.194850] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[ 0.207326] ACPI: Dynamic OEM Table Load:
[ 0.207339] ACPI: SSDT 0xFFFF880213EE7000 0003D3 (v01 PmRef Cpu0Cst 00003001 INTL 20120711)
[ 0.220827] ACPI: Dynamic OEM Table Load:
[ 0.220838] ACPI: SSDT 0xFFFF880213F81000 0005AA (v01 PmRef ApIst 00003000 INTL 20120711)
[ 0.237345] ACPI: Dynamic OEM Table Load:
[ 0.237354] ACPI: SSDT 0xFFFF880213F56200 000119 (v01 PmRef ApCst 00003000 INTL 20120711)
[ 0.255255] ACPI: Interpreter enabled
[ 0.255267] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20140424/hwxface-580)
[ 0.255275] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20140424/hwxface-580)
[ 0.255298] ACPI: (supports S0 S3 S4 S5)
[ 0.255300] ACPI: Using IOAPIC for interrupt routing
[ 0.255336] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.268419] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3e])
[ 0.268426] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[ 0.268573] \_SB_.PCI0:_OSC invalid UUID
[ 0.268575] _OSC request data:1 1f 0
[ 0.268579] acpi PNP0A08:00: _OSC failed (AE_ERROR); disabling ASPM
[ 0.269580] PCI host bridge to bus 0000:00
[ 0.269584] pci_bus 0000:00: root bus resource [bus 00-3e]
[ 0.269586] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
[ 0.269588] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
[ 0.269590] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[ 0.269592] pci_bus 0000:00: root bus resource [mem 0xdfa00000-0xfeafffff]
[ 0.269601] pci 0000:00:00.0: [8086:0a04] type 00 class 0x060000
[ 0.269803] pci 0000:00:02.0: [8086:0a16] type 00 class 0x030000
[ 0.269817] pci 0000:00:02.0: reg 0x10: [mem 0xf0000000-0xf03fffff 64bit]
[ 0.269826] pci 0000:00:02.0: reg 0x18: [mem 0xe0000000-0xefffffff 64bit pref]
[ 0.269831] pci 0000:00:02.0: reg 0x20: [io 0x3000-0x303f]
[ 0.270019] pci 0000:00:03.0: [8086:0a0c] type 00 class 0x040300
[ 0.270029] pci 0000:00:03.0: reg 0x10: [mem 0xf0510000-0xf0513fff 64bit]
[ 0.270244] pci 0000:00:14.0: [8086:9c31] type 00 class 0x0c0330
[ 0.270263] pci 0000:00:14.0: reg 0x10: [mem 0xf0500000-0xf050ffff 64bit]
[ 0.270324] pci 0000:00:14.0: PME# supported from D3hot D3cold
[ 0.270459] pci 0000:00:14.0: System wakeup disabled by ACPI
[ 0.270505] pci 0000:00:16.0: [8086:9c3a] type 00 class 0x078000
[ 0.270526] pci 0000:00:16.0: reg 0x10: [mem 0xf0519000-0xf051901f 64bit]
[ 0.270598] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[ 0.270790] pci 0000:00:1b.0: [8086:9c20] type 00 class 0x040300
[ 0.270806] pci 0000:00:1b.0: reg 0x10: [mem 0xf0514000-0xf0517fff 64bit]
[ 0.270876] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.271011] pci 0000:00:1b.0: System wakeup disabled by ACPI
[ 0.271060] pci 0000:00:1c.0: [8086:9c10] type 01 class 0x060400
[ 0.271140] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.271279] pci 0000:00:1c.0: System wakeup disabled by ACPI
[ 0.271327] pci 0000:00:1c.2: [8086:9c14] type 01 class 0x060400
[ 0.271410] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[ 0.271549] pci 0000:00:1c.2: System wakeup disabled by ACPI
[ 0.271602] pci 0000:00:1d.0: [8086:9c26] type 00 class 0x0c0320
[ 0.271624] pci 0000:00:1d.0: reg 0x10: [mem 0xf051d000-0xf051d3ff]
[ 0.271716] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[ 0.271867] pci 0000:00:1d.0: System wakeup disabled by ACPI
[ 0.271914] pci 0000:00:1f.0: [8086:9c43] type 00 class 0x060100
[ 0.272193] pci 0000:00:1f.2: [8086:9c03] type 00 class 0x010601
[ 0.272209] pci 0000:00:1f.2: reg 0x10: [io 0x3088-0x308f]
[ 0.272217] pci 0000:00:1f.2: reg 0x14: [io 0x3094-0x3097]
[ 0.272225] pci 0000:00:1f.2: reg 0x18: [io 0x3080-0x3087]
[ 0.272232] pci 0000:00:1f.2: reg 0x1c: [io 0x3090-0x3093]
[ 0.272240] pci 0000:00:1f.2: reg 0x20: [io 0x3060-0x307f]
[ 0.272247] pci 0000:00:1f.2: reg 0x24: [mem 0xf051c000-0xf051c7ff]
[ 0.272285] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.272451] pci 0000:00:1f.3: [8086:9c22] type 00 class 0x0c0500
[ 0.272466] pci 0000:00:1f.3: reg 0x10: [mem 0xf0518000-0xf05180ff 64bit]
[ 0.272486] pci 0000:00:1f.3: reg 0x20: [io 0xefa0-0xefbf]
[ 0.272737] pci 0000:00:1c.0: PCI bridge to [bus 01]
[ 0.272853] pci 0000:02:00.0: [8086:08b1] type 00 class 0x028000
[ 0.272899] pci 0000:02:00.0: reg 0x10: [mem 0xf0400000-0xf0401fff 64bit]
[ 0.273097] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[ 0.273145] pci 0000:02:00.0: System wakeup disabled by ACPI
[ 0.277341] pci 0000:00:1c.2: PCI bridge to [bus 02]
[ 0.277347] pci 0000:00:1c.2: bridge window [mem 0xf0400000-0xf04fffff]
[ 0.294607] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 *11 12 14 15)
[ 0.294666] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.294723] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 10 11 12 14 15) *7
[ 0.294778] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 *10 11 12 14 15)
[ 0.294832] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.294886] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.294940] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 10 *11 12 14 15)
[ 0.294995] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *10 11 12 14 15)
[ 0.295346] ACPI: Enabled 5 GPEs in block 00 to 7F
[ 0.295416] ACPI : EC: GPE = 0xa, I/O: command/status = 0x66, data = 0x62
[ 0.295555] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.295559] vgaarb: loaded
[ 0.295560] vgaarb: bridge control possible 0000:00:02.0
[ 0.295603] PCI: Using ACPI for IRQ routing
[ 0.297024] PCI: pci_cache_line_size set to 64 bytes
[ 0.297085] e820: reserve RAM buffer [mem 0x0009d000-0x0009ffff]
[ 0.297087] e820: reserve RAM buffer [mem 0xc287a000-0xc3ffffff]
[ 0.297088] e820: reserve RAM buffer [mem 0x21f600000-0x21fffffff]
[ 0.297209] NetLabel: Initializing
[ 0.297211] NetLabel: domain hash size = 128
[ 0.297212] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.297225] NetLabel: unlabeled traffic allowed by default
[ 0.297250] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[ 0.297256] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[ 0.299294] Switched to clocksource hpet
[ 0.305097] pnp: PnP ACPI init
[ 0.305113] ACPI: bus type PNP registered
[ 0.305253] system 00:00: [io 0x0680-0x069f] has been reserved
[ 0.305256] system 00:00: [io 0xffff] has been reserved
[ 0.305259] system 00:00: [io 0xffff] has been reserved
[ 0.305262] system 00:00: [io 0xffff] has been reserved
[ 0.305265] system 00:00: [io 0x1800-0x18fe] could not be reserved
[ 0.305267] system 00:00: [io 0x164e-0x164f] has been reserved
[ 0.305270] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.305325] pnp 00:01: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.305378] system 00:02: [io 0x1854-0x1857] has been reserved
[ 0.305381] system 00:02: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
[ 0.305426] pnp 00:03: Plug and Play ACPI device, IDs PNP0303 (active)
[ 0.305459] pnp 00:04: Plug and Play ACPI device, IDs SYN0608 PNP0f03 (active)
[ 0.305612] system 00:05: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 0.305614] system 00:05: [mem 0xfed10000-0xfed17fff] has been reserved
[ 0.305617] system 00:05: [mem 0xfed18000-0xfed18fff] has been reserved
[ 0.305619] system 00:05: [mem 0xfed19000-0xfed19fff] has been reserved
[ 0.305621] system 00:05: [mem 0xf8000000-0xfbffffff] has been reserved
[ 0.305623] system 00:05: [mem 0xfed20000-0xfed3ffff] has been reserved
[ 0.305625] system 00:05: [mem 0xfed90000-0xfed93fff] has been reserved
[ 0.305627] system 00:05: [mem 0xfed45000-0xfed8ffff] has been reserved
[ 0.305630] system 00:05: [mem 0xff000000-0xffffffff] could not be reserved
[ 0.305632] system 00:05: [mem 0xfee00000-0xfeefffff] could not be reserved
[ 0.305634] system 00:05: [mem 0xdfa10000-0xdfa1ffff] has been reserved
[ 0.305637] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.305958] system 00:06: [mem 0xfe102000-0xfe102fff] has been reserved
[ 0.305961] system 00:06: [mem 0xfe104000-0xfe104fff] has been reserved
[ 0.305971] system 00:06: [mem 0xfe106000-0xfe106fff] has been reserved
[ 0.305974] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.306696] pnp: PnP ACPI: found 7 devices
[ 0.306698] ACPI: bus type PNP unregistered
[ 0.313588] pci 0000:00:1c.0: PCI bridge to [bus 01]
[ 0.313602] pci 0000:00:1c.2: PCI bridge to [bus 02]
[ 0.313608] pci 0000:00:1c.2: bridge window [mem 0xf0400000-0xf04fffff]
[ 0.313617] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 0.313620] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 0.313622] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.313624] pci_bus 0000:00: resource 7 [mem 0xdfa00000-0xfeafffff]
[ 0.313626] pci_bus 0000:02: resource 1 [mem 0xf0400000-0xf04fffff]
[ 0.313661] NET: Registered protocol family 2
[ 0.313895] TCP established hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.314065] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.314196] TCP: Hash tables configured (established 65536 bind 65536)
[ 0.314216] TCP: reno registered
[ 0.314229] UDP hash table entries: 4096 (order: 5, 131072 bytes)
[ 0.314260] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
[ 0.314329] NET: Registered protocol family 1
[ 0.314345] pci 0000:00:02.0: Boot video device
[ 0.314427] pci 0000:00:14.0: can't derive routing for PCI INT A
[ 0.314429] pci 0000:00:14.0: PCI INT A: no GSI
[ 0.314520] pci 0000:00:14.0: can't derive routing for PCI INT A
[ 0.314702] PCI: CLS 64 bytes, default 64
[ 0.314746] Unpacking initramfs...
[ 0.389760] Freeing initrd memory: 3340K (ffff88003796a000 - ffff880037cad000)
[ 0.389768] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.389771] software IO TLB [mem 0xbe87a000-0xc287a000] (64MB) mapped at [ffff8800be87a000-ffff8800c2879fff]
[ 0.389991] RAPL PMU detected, hw unit 2^-14 Joules, API unit is 2^-32 Joules, 4 fixed counters 655360 ms ovfl timer
[ 0.390043] Scanning for low memory corruption every 60 seconds
[ 0.390383] futex hash table entries: 2048 (order: 5, 131072 bytes)
[ 0.390776] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.392315] zbud: loaded
[ 0.392526] VFS: Disk quotas dquot_6.5.2
[ 0.392564] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.392709] msgmni has been set to 15022
[ 0.392776] Key type big_key registered
[ 0.392952] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.393009] io scheduler noop registered
[ 0.393014] io scheduler deadline registered
[ 0.393072] io scheduler cfq registered (default)
[ 0.393422] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.393440] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.393482] intel_idle: MWAIT substates: 0x11142120
[ 0.393484] intel_idle: v0.4 model 0x45
[ 0.393485] intel_idle: lapic_timer_reliable_states 0xffffffff
[ 0.393772] GHES: HEST is not enabled!
[ 0.393860] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.394367] Linux agpgart interface v0.103
[ 0.394421] rtc_cmos 00:01: RTC can wake from S4
[ 0.394566] rtc_cmos 00:01: rtc core: registered rtc_cmos as rtc0
[ 0.394596] rtc_cmos 00:01: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[ 0.394611] Intel P-state driver initializing.
[ 0.394625] Intel pstate controlling: cpu 0
[ 0.394647] Intel pstate controlling: cpu 1
[ 0.394663] Intel pstate controlling: cpu 2
[ 0.394684] Intel pstate controlling: cpu 3
[ 0.394756] ledtrig-cpu: registered to indicate activity on CPUs
[ 0.395139] TCP: cubic registered
[ 0.395367] NET: Registered protocol family 10
[ 0.395811] NET: Registered protocol family 17
[ 0.396487] registered taskstats version 1
[ 0.397305] Magic number: 2:622:755
[ 0.397469] rtc_cmos 00:01: setting system clock to 2014-10-21 22:42:27 UTC (1413931347)
[ 0.397659] PM: Hibernation image not present or could not be loaded.
[ 0.399550] Freeing unused kernel memory: 1128K (ffffffff818df000 - ffffffff819f9000)
[ 0.399554] Write protecting the kernel read-only data: 8192k
[ 0.403618] Freeing unused kernel memory: 796K (ffff880001539000 - ffff880001600000)
[ 0.404603] Freeing unused kernel memory: 360K (ffff8800017a6000 - ffff880001800000)
[ 0.411279] random: systemd-tmpfile urandom read with 4 bits of entropy available
[ 0.412549] systemd-udevd[57]: starting version 216
[ 0.429661] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[ 0.430313] sdhci: Secure Digital Host Controller Interface driver
[ 0.430315] sdhci: Copyright(c) Pierre Ossman
[ 0.435942] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.436007] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.441502] ACPI: bus type USB registered
[ 0.441544] usbcore: registered new interface driver usbfs
[ 0.441562] usbcore: registered new interface driver hub
[ 0.441712] usbcore: registered new device driver usb
[ 0.442370] SCSI subsystem initialized
[ 0.442606] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.442897] ehci-pci: EHCI PCI platform driver
[ 0.443091] ehci-pci 0000:00:1d.0: EHCI Host Controller
[ 0.443106] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 1
[ 0.443121] ehci-pci 0000:00:1d.0: debug port 2
[ 0.444256] libata version 3.00 loaded.
[ 0.447021] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
[ 0.447046] ehci-pci 0000:00:1d.0: irq 23, io mem 0xf051d000
[ 0.456197] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[ 0.456468] hub 1-0:1.0: USB hub found
[ 0.456636] hub 1-0:1.0: 2 ports detected
[ 0.456998] xhci_hcd 0000:00:14.0: can't derive routing for PCI INT A
[ 0.457003] xhci_hcd 0000:00:14.0: PCI INT A: no GSI
[ 0.457028] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 0.457038] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
[ 0.457132] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
[ 0.457158] xhci_hcd 0000:00:14.0: irq 56 for MSI/MSI-X
[ 0.457437] hub 2-0:1.0: USB hub found
[ 0.457454] hub 2-0:1.0: 9 ports detected
[ 0.460686] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 0.460692] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 3
[ 0.460861] hub 3-0:1.0: USB hub found
[ 0.460871] hub 3-0:1.0: 4 ports detected
[ 0.461773] ahci 0000:00:1f.2: version 3.0
[ 0.461915] ahci 0000:00:1f.2: irq 57 for MSI/MSI-X
[ 0.471676] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 0.472802] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 4 ports 6 Gbps 0x4 impl SATA mode
[ 0.472807] ahci 0000:00:1f.2: flags: 64bit ncq pm led clo only pio slum part deso sadm sds apst
[ 0.473307] scsi0 : ahci
[ 0.473445] scsi1 : ahci
[ 0.473555] scsi2 : ahci
[ 0.473668] scsi3 : ahci
[ 0.473715] ata1: DUMMY
[ 0.473717] ata2: DUMMY
[ 0.473719] ata3: SATA max UDMA/133 abar m2048@0xf051c000 port 0xf051c200 irq 57
[ 0.473721] ata4: DUMMY
[ 0.763125] usb 1-1: new high-speed USB device number 2 using ehci-pci
[ 0.793107] ata3: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 0.793458] ata3.00: ATA-8: LITEONIT LMT-256M6M mSATA 256GB, DM8110F, max UDMA/133
[ 0.793461] ata3.00: 500118192 sectors, multi 1: LBA48 NCQ (depth 31/32), AA
[ 0.794069] ata3.00: configured for UDMA/133
[ 0.794234] scsi 2:0:0:0: Direct-Access ATA LITEONIT LMT-256 10F PQ: 0 ANSI: 5
[ 0.798767] sd 2:0:0:0: [sda] 500118192 512-byte logical blocks: (256 GB/238 GiB)
[ 0.798902] sd 2:0:0:0: [sda] Write Protect is off
[ 0.798906] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 0.798943] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 0.799393] sda: sda3 sda4
[ 0.799749] sd 2:0:0:0: [sda] Attached SCSI disk
[ 0.841216] EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: (null)
[ 0.887143] hub 1-1:1.0: USB hub found
[ 0.887202] hub 1-1:1.0: 8 ports detected
[ 0.946321] systemd[1]: Cannot add dependency job for unit nfs-server.target, ignoring: Unit nfs-server.target failed to load: No such file or directory.
[ 0.946348] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory.
[ 0.960139] EXT4-fs (sda4): re-mounted. Opts: data=ordered,discard
[ 0.981520] FS-Cache: Loaded
[ 0.992070] RPC: Registered named UNIX socket transport module.
[ 0.992075] RPC: Registered udp transport module.
[ 0.992077] RPC: Registered tcp transport module.
[ 0.992079] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.004660] FS-Cache: Netfs 'nfs' registered for caching
[ 1.007058] Netfilter messages via NETLINK v0.30.
[ 1.008839] nf_tables: (c) 2007-2009 Patrick McHardy <[email protected]>
[ 1.023856] vboxdrv: Found 4 processor cores.
[ 1.024080] vboxdrv: fAsync=0 offMin=0x2c2 offMax=0x31e0
[ 1.024169] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[ 1.024172] vboxdrv: Successfully loaded version 4.3.18_OSE (interface 0x001a0008).
[ 1.046603] usb 2-3: new full-speed USB device number 2 using xhci_hcd
[ 1.322293] systemd-udevd[170]: starting version 216
[ 1.380209] usb 2-5: new high-speed USB device number 3 using xhci_hcd
[ 1.393592] tsc: Refined TSC clocksource calibration: 2394.460 MHz
[ 1.439202] systemd-journald[135]: Received request to flush runtime journal from PID 1
[ 1.471000] hidraw: raw HID events driver (C) Jiri Kosina
[ 1.476250] systemd-journald[135]: File /var/log/journal/88482a6e208046b4ab2b978eaa052ecd/system.journal corrupted or uncleanly shut down, renaming and replacing.
[ 1.510556] thermal LNXTHERM:00: registered as thermal_zone0
[ 1.510560] ACPI: Thermal Zone [TZ00] (28 C)
[ 1.510856] thermal LNXTHERM:01: registered as thermal_zone1
[ 1.510860] ACPI: Thermal Zone [TZ01] (30 C)
[ 1.516235] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 1.526161] ACPI Warning: SystemIO range 0x000000000000efa0-0x000000000000efbf conflicts with OpRegion 0x000000000000efa0-0x000000000000efaf (\_SB_.PCI0.SBUS.SMBI) (20140424/utaddress-258)
[ 1.526172] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 1.545038] mei_me 0000:00:16.0: irq 58 for MSI/MSI-X
[ 1.552395] cfg80211: Calling CRDA to update world regulatory domain
[ 1.576090] [drm] Initialized drm 1.1.0 20060810
[ 1.580291] random: nonblocking pool is initialized
[ 1.596486] Intel(R) Wireless WiFi driver for Linux, in-tree:
[ 1.596490] Copyright(c) 2003- 2014 Intel Corporation
[ 1.596517] snd_hda_intel: probe of 0000:00:03.0 failed with error -2
[ 1.596724] snd_hda_intel 0000:00:1b.0: irq 59 for MSI/MSI-X
[ 1.597671] iwlwifi 0000:02:00.0: irq 60 for MSI/MSI-X
[ 1.606282] iwlwifi 0000:02:00.0: loaded firmware version 23.214.9.0 op_mode iwlmvm
[ 1.622623] sound hdaudioC0D0: autoconfig: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:speaker
[ 1.622630] sound hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 1.622633] sound hdaudioC0D0: hp_outs=1 (0x15/0x0/0x0/0x0/0x0)
[ 1.622636] sound hdaudioC0D0: mono: mono_out=0x0
[ 1.622639] sound hdaudioC0D0: inputs:
[ 1.622643] sound hdaudioC0D0: Headphone Mic=0x19
[ 1.622646] sound hdaudioC0D0: Headset Mic=0x1b
[ 1.622649] sound hdaudioC0D0: Internal Mic=0x12
[ 1.627117] ACPI: AC Adapter [ADP0] (off-line)
[ 1.628753] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input4
[ 1.628924] ACPI: Power Button [PWRB]
[ 1.629010] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input5
[ 1.630785] ACPI: Lid Switch [LID0]
[ 1.630887] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input6
[ 1.631327] ACPI: Power Button [PWRF]
[ 1.633943] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/sound/card0/hdaudioC0D0/input3
[ 1.634197] input: HDA Intel PCH Headphone Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7
[ 1.635366] microcode: CPU0 sig=0x40651, pf=0x40, revision=0x16
[ 1.635406] microcode: CPU1 sig=0x40651, pf=0x40, revision=0x16
[ 1.635428] microcode: CPU2 sig=0x40651, pf=0x40, revision=0x16
[ 1.635449] microcode: CPU3 sig=0x40651, pf=0x40, revision=0x16
[ 1.635520] microcode: Microcode Update Driver: v2.00 <[email protected]>, Peter Oruba
[ 1.639579] ACPI: Battery Slot [BAT0] (battery present)
[ 1.640267] iwlwifi 0000:02:00.0: Detected Intel(R) Dual Band Wireless AC 7260, REV=0x144
[ 1.640997] iwlwifi 0000:02:00.0: L1 Enabled; Disabling L0S
[ 1.641000] wmi: Mapper loaded
[ 1.641249] iwlwifi 0000:02:00.0: L1 Enabled; Disabling L0S
[ 1.644274] AVX2 version of gcm_enc/dec engaged.
[ 1.662640] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[ 1.707814] iTCO_vendor_support: vendor-support=0
[ 1.709016] [drm] Memory usable by graphics device = 2048M
[ 1.709022] [drm] Replacing VGA console driver
[ 1.710234] Console: switching to colour dummy device 80x25
[ 1.710749] hid-rmi 0018:06CB:2734.0001: Scanning PDT...
[ 1.711895] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
[ 1.711954] iTCO_wdt: Found a Lynx Point_LP TCO device (Version=2, TCOBASE=0x1860)
[ 1.712089] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 1.713279] hid-rmi 0018:06CB:2734.0001: Found F34 on page 0x00
[ 1.715870] hid-rmi 0018:06CB:2734.0001: Found F01 on page 0x00
[ 1.718203] hid-rmi 0018:06CB:2734.0001: Found F11 on page 0x00
[ 1.724578] hid-rmi 0018:06CB:2734.0001: Found F54 on page 0x01
[ 1.727275] hid-rmi 0018:06CB:2734.0001: Found F30 on page 0x01
[ 1.730545] i915 0000:00:02.0: irq 61 for MSI/MSI-X
[ 1.730561] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 1.730563] [drm] Driver supports precise vblank timestamp query.
[ 1.730596] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 1.733539] hid-rmi 0018:06CB:2734.0001: Found F55 on page 0x02
[ 1.738729] hid-rmi 0018:06CB:2734.0001: Found F51 on page 0x03
[ 1.740512] usb 2-6: new full-speed USB device number 4 using xhci_hcd
[ 1.744701] hid-rmi 0018:06CB:2734.0001: rmi_scan_pdt: Done with PDT scan.
[ 1.756260] [drm] VBT doesn't support DRRS
[ 1.758240] hid-rmi 0018:06CB:2734.0001: rmi_populate_f11: size in mm: 97 x 59
[ 1.766636] input: DLL060A:00 06CB:2734 as /devices/pci0000:00/INT33C3:00/i2c-0/i2c-DLL060A:00/0018:06CB:2734.0001/input/input8
[ 1.766734] hid-rmi 0018:06CB:2734.0001: input,hidraw0: <UNKNOWN> HID v1.00 Pointer [DLL060A:00 06CB:2734] on
[ 1.775456] fbcon: inteldrmfb (fb0) is primary device
[ 1.802968] input: Dell WMI hotkeys as /devices/virtual/input/input9
[ 1.808667] mousedev: PS/2 mouse device common for all mice
[ 1.841252] ieee80211 phy0: Selected rate control algorithm 'iwl-mvm-rs'
[ 1.842535] iwlwifi 0000:02:00.0: L1 Enabled; Disabling L0S
[ 1.842776] iwlwifi 0000:02:00.0: L1 Enabled; Disabling L0S
[ 1.854793] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 2.394398] Switched to clocksource tsc
[ 2.838140] Console: switching to colour frame buffer device 240x67
[ 2.845934] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[ 2.845936] i915 0000:00:02.0: registered panic notifier
[ 2.876371] media: Linux media interface: v0.10
[ 2.876864] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 2.877001] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input10
[ 2.877148] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 2.879690] usbcore: registered new interface driver usbhid
[ 2.879694] usbhid: USB HID core driver
[ 2.883145] Linux video capture interface: v2.00
[ 2.892232] input: SYNAPTICS Synaptics Large Touch Screen as /devices/pci0000:00/0000:00:14.0/usb2/2-3/2-3:1.0/0003:06CB:0AF8.0002/input/input11
[ 2.892497] uvcvideo: Found UVC 1.00 device Integrated_Webcam_HD (0bda:5752)
[ 2.895106] hid-multitouch 0003:06CB:0AF8.0002: input,hiddev0,hidraw1: USB HID v1.11 Mouse [SYNAPTICS Synaptics Large Touch Screen] on usb-0000:00:14.0-3/input0
[ 2.895830] Bluetooth: Core ver 2.19
[ 2.895849] NET: Registered protocol family 31
[ 2.895852] Bluetooth: HCI device and connection manager initialized
[ 2.895861] Bluetooth: HCI socket layer initialized
[ 2.895864] Bluetooth: L2CAP socket layer initialized
[ 2.895877] Bluetooth: SCO socket layer initialized
[ 2.901636] input: Integrated_Webcam_HD as /devices/pci0000:00/0000:00:14.0/usb2/2-5/2-5:1.0/input/input13
[ 2.901827] usbcore: registered new interface driver uvcvideo
[ 2.901830] USB Video Class driver (1.1.1)
[ 2.910511] usbcore: registered new interface driver btusb
[ 2.925460] Bluetooth: hci0: read Intel version: 370710018002030d2e
[ 2.925464] Bluetooth: hci0: Intel device is already patched. patch num: 2e
[ 3.331899] [drm] Enabling RC6 states: RC6 on, RC6p off, RC6pp off
[ 11.275262] systemd-journald[135]: File /var/log/journal/88482a6e208046b4ab2b978eaa052ecd/user-1001.journal corrupted or uncleanly shut down, renaming and replacing.
[ 35.164461] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 35.241753] iwlwifi 0000:02:00.0: L1 Enabled; Disabling L0S
[ 35.241999] iwlwifi 0000:02:00.0: L1 Enabled; Disabling L0S
[ 35.255097] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 36.055112] wlan0: authenticate with c0:25:06:84:57:f0
[ 36.058891] wlan0: send auth to c0:25:06:84:57:f0 (try 1/3)
[ 36.061335] wlan0: authenticated
[ 36.061563] wlan0: associate with c0:25:06:84:57:f0 (try 1/3)
[ 36.067260] wlan0: RX AssocResp from c0:25:06:84:57:f0 (capab=0x431 status=0 aid=1)
[ 36.070080] wlan0: associated
[ 36.070111] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 36.070172] cfg80211: Calling CRDA to update world regulatory domain
[ 4501.338278] PM: Syncing filesystems ...
[ 4501.341188] atkbd serio0: Unknown key pressed (translated set 2, code 0xf2 on isa0060/serio0).
[ 4501.341196] atkbd serio0: Use 'setkeycodes e072 <keycode>' to make it known.
[ 4501.348617] done.
[ 4501.348622] PM: Preparing system for mem sleep
[ 4501.349019] Freezing user space processes ... (elapsed 0.001 seconds) done.
[ 4501.350459] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[ 4501.351580] PM: Entering mem sleep
[ 4501.351657] Suspending console(s) (use no_console_suspend to debug)
[ 4501.351917] wlan0: deauthenticating from c0:25:06:84:57:f0 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 4501.358219] atkbd serio0: Unknown key released (translated set 2, code 0xf2 on isa0060/serio0).
[ 4501.358222] atkbd serio0: Use 'setkeycodes e072 <keycode>' to make it known.
[ 4501.361609] cfg80211: Calling CRDA for country: DE
[ 4501.362122] sd 2:0:0:0: [sda] Synchronizing SCSI cache
[ 4501.362185] sd 2:0:0:0: [sda] Stopping disk
[ 4501.992409] PM: suspend of devices complete after 640.028 msecs
[ 4502.005724] PM: late suspend of devices complete after 13.299 msecs
[ 4502.006247] ehci-pci 0000:00:1d.0: System wakeup enabled by ACPI
[ 4502.006367] xhci_hcd 0000:00:14.0: System wakeup enabled by ACPI
[ 4502.019376] PM: noirq suspend of devices complete after 13.638 msecs
[ 4502.019816] ACPI: Preparing to enter system sleep state S3
[ 4502.020586] PM: Saving platform NVS memory
[ 4502.021109] Disabling non-boot CPUs ...
[ 4502.021139] intel_pstate CPU 1 exiting
[ 4502.022404] kvm: disabling virtualization on CPU1
[ 4502.022854] smpboot: CPU 1 is now offline
[ 4502.023143] intel_pstate CPU 2 exiting
[ 4502.024386] kvm: disabling virtualization on CPU2
[ 4502.125774] smpboot: CPU 2 is now offline
[ 4502.126039] intel_pstate CPU 3 exiting
[ 4502.127395] kvm: disabling virtualization on CPU3
[ 4502.229207] smpboot: CPU 3 is now offline
[ 4502.232189] ACPI: Low-level resume complete
[ 4502.232259] PM: Restoring platform NVS memory
[ 4502.232774] Enabling non-boot CPUs ...
[ 4502.232814] x86: Booting SMP configuration:
[ 4502.232815] smpboot: Booting Node 0 Processor 1 APIC 0x1
[ 4502.245238] kvm: enabling virtualization on CPU1
[ 4502.247462] Intel pstate controlling: cpu 1
[ 4502.247514] CPU1 is up
[ 4502.247533] smpboot: Booting Node 0 Processor 2 APIC 0x2
[ 4502.259870] kvm: enabling virtualization on CPU2
[ 4502.262107] Intel pstate controlling: cpu 2
[ 4502.262155] CPU2 is up
[ 4502.262172] smpboot: Booting Node 0 Processor 3 APIC 0x3
[ 4502.274504] kvm: enabling virtualization on CPU3
[ 4502.276760] Intel pstate controlling: cpu 3
[ 4502.276807] CPU3 is up
[ 4502.282141] ACPI: Waking up from system sleep state S3
[ 4502.302447] ehci-pci 0000:00:1d.0: System wakeup disabled by ACPI
[ 4502.302450] xhci_hcd 0000:00:14.0: System wakeup disabled by ACPI
[ 4502.302690] PM: noirq resume of devices complete after 11.863 msecs
[ 4502.303102] PM: early resume of devices complete after 0.384 msecs
[ 4502.303194] usb usb2: root hub lost power or was reset
[ 4502.303197] usb usb3: root hub lost power or was reset
[ 4502.315679] mei_me 0000:00:16.0: irq 58 for MSI/MSI-X
[ 4502.315810] snd_hda_intel 0000:00:1b.0: irq 59 for MSI/MSI-X
[ 4502.329054] sd 2:0:0:0: [sda] Starting disk
[ 4502.390642] xhci_hcd 0000:00:14.0: irq 56 for MSI/MSI-X
[ 4502.535888] usb 1-1: reset high-speed USB device number 2 using ehci-pci
[ 4502.643402] iwlwifi 0000:02:00.0: L1 Enabled; Disabling L0S
[ 4502.643646] iwlwifi 0000:02:00.0: L1 Enabled; Disabling L0S
[ 4502.649288] ata3: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 4502.652119] ata3.00: configured for UDMA/133
[ 4502.766135] usb 2-3: reset full-speed USB device number 2 using xhci_hcd
[ 4502.939946] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff880212c09480
[ 4502.939950] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff880212c094c8
[ 4503.099825] usb 2-6: reset full-speed USB device number 4 using xhci_hcd
[ 4503.273741] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8800bdea5a00
[ 4503.273745] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8800bdea5a48
[ 4503.273748] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8800bdea5a90
[ 4503.273750] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88020c2a6000
[ 4503.273752] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88020c2a6048
[ 4503.274732] PM: resume of devices complete after 970.836 msecs
[ 4503.275664] PM: Finishing wakeup.
[ 4503.275668] Restarting tasks ...
[ 4503.275774] iwlwifi 0000:02:00.0: no hotplug settings from platform
[ 4503.276362] usb 2-5: USB disconnect, device number 3
[ 4503.276546] pci_bus 0000:01: Allocating resources
[ 4503.276576] pcieport 0000:00:1c.0: bridge window [io 0x1000-0x0fff] to [bus 01] add_size 1000
[ 4503.276585] pcieport 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 01] add_size 200000
[ 4503.276592] pcieport 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff] to [bus 01] add_size 200000
[ 4503.276596] done.
[ 4503.276614] pci_bus 0000:02: Allocating resources
[ 4503.276646] pcieport 0000:00:1c.2: bridge window [io 0x1000-0x0fff] to [bus 02] add_size 1000
[ 4503.276653] pcieport 0000:00:1c.2: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 02] add_size 200000
[ 4503.276662] i915 0000:00:02.0: BAR 6: [??? 0x00000000 flags 0x2] has bogus alignment
[ 4503.276675] pcieport 0000:00:1c.0: res[14]=[mem 0x00100000-0x000fffff] get_res_add_size add_size 200000
[ 4503.276681] pcieport 0000:00:1c.0: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
[ 4503.276688] pcieport 0000:00:1c.2: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
[ 4503.276695] pcieport 0000:00:1c.0: res[13]=[io 0x1000-0x0fff] get_res_add_size add_size 1000
[ 4503.276701] pcieport 0000:00:1c.2: res[13]=[io 0x1000-0x0fff] get_res_add_size add_size 1000
[ 4503.276712] pcieport 0000:00:1c.0: BAR 14: assigned [mem 0xdfb00000-0xdfcfffff]
[ 4503.276726] pcieport 0000:00:1c.0: BAR 15: assigned [mem 0xdfd00000-0xdfefffff 64bit pref]
[ 4503.276739] pcieport 0000:00:1c.2: BAR 15: assigned [mem 0xf0600000-0xf07fffff 64bit pref]
[ 4503.276748] pcieport 0000:00:1c.0: BAR 13: assigned [io 0x2000-0x2fff]
[ 4503.276756] pcieport 0000:00:1c.2: BAR 13: assigned [io 0x4000-0x4fff]
[ 4503.276773] pci 0000:00:00.0: no hotplug settings from platform
[ 4503.276778] pci 0000:00:00.0: using default PCI settings
[ 4503.276791] i915 0000:00:02.0: no hotplug settings from platform
[ 4503.276795] i915 0000:00:02.0: using default PCI settings
[ 4503.276809] pci 0000:00:03.0: no hotplug settings from platform
[ 4503.276816] xhci_hcd 0000:00:14.0: no hotplug settings from platform
[ 4503.276820] xhci_hcd 0000:00:14.0: using default PCI settings
[ 4503.276836] mei_me 0000:00:16.0: no hotplug settings from platform
[ 4503.276839] mei_me 0000:00:16.0: using default PCI settings
[ 4503.276855] snd_hda_intel 0000:00:1b.0: no hotplug settings from platform
[ 4503.276863] pcieport 0000:00:1c.0: no hotplug settings from platform
[ 4503.276871] pcieport 0000:00:1c.2: no hotplug settings from platform
[ 4503.276904] iwlwifi 0000:02:00.0: no hotplug settings from platform
[ 4503.276912] ehci-pci 0000:00:1d.0: no hotplug settings from platform
[ 4503.276917] ehci-pci 0000:00:1d.0: using default PCI settings
[ 4503.276933] lpc_ich 0000:00:1f.0: no hotplug settings from platform
[ 4503.276938] lpc_ich 0000:00:1f.0: using default PCI settings
[ 4503.276956] ahci 0000:00:1f.2: no hotplug settings from platform
[ 4503.276961] ahci 0000:00:1f.2: using default PCI settings
[ 4503.276976] pci 0000:00:1f.3: no hotplug settings from platform
[ 4503.276980] pci 0000:00:1f.3: using default PCI settings
[ 4503.277590] pci_bus 0000:01: Allocating resources
[ 4503.277619] pci_bus 0000:02: Allocating resources
[ 4503.277652] i915 0000:00:02.0: BAR 6: [??? 0x00000000 flags 0x2] has bogus alignment
[ 4503.277669] pci 0000:00:00.0: no hotplug settings from platform
[ 4503.277673] pci 0000:00:00.0: using default PCI settings
[ 4503.277686] i915 0000:00:02.0: no hotplug settings from platform
[ 4503.277690] i915 0000:00:02.0: using default PCI settings
[ 4503.277703] pci 0000:00:03.0: no hotplug settings from platform
[ 4503.277711] xhci_hcd 0000:00:14.0: no hotplug settings from platform
[ 4503.277716] xhci_hcd 0000:00:14.0: using default PCI settings
[ 4503.277731] mei_me 0000:00:16.0: no hotplug settings from platform
[ 4503.277736] mei_me 0000:00:16.0: using default PCI settings
[ 4503.277751] snd_hda_intel 0000:00:1b.0: no hotplug settings from platform
[ 4503.277759] pcieport 0000:00:1c.0: no hotplug settings from platform
[ 4503.277767] pcieport 0000:00:1c.2: no hotplug settings from platform
[ 4503.277801] iwlwifi 0000:02:00.0: no hotplug settings from platform
[ 4503.277809] ehci-pci 0000:00:1d.0: no hotplug settings from platform
[ 4503.277814] ehci-pci 0000:00:1d.0: using default PCI settings
[ 4503.277830] lpc_ich 0000:00:1f.0: no hotplug settings from platform
[ 4503.277835] lpc_ich 0000:00:1f.0: using default PCI settings
[ 4503.277852] ahci 0000:00:1f.2: no hotplug settings from platform
[ 4503.277857] ahci 0000:00:1f.2: using default PCI settings
[ 4503.277871] pci 0000:00:1f.3: no hotplug settings from platform
[ 4503.277875] pci 0000:00:1f.3: using default PCI settings
[ 4503.287972] Bluetooth: hci0: read Intel version: 370710018002030d00
[ 4503.551878] Bluetooth: hci0: Intel Bluetooth firmware file: intel/ibt-hw-37.7.10-fw-1.80.2.3.d.bseq
[ 4503.596787] usb 2-5: new high-speed USB device number 5 using xhci_hcd
[ 4503.633858] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 4503.755400] Bluetooth: hci0: Intel Bluetooth firmware patch completed and activated
[ 4503.797807] uvcvideo: Found UVC 1.00 device Integrated_Webcam_HD (0bda:5752)
[ 4503.801045] input: Integrated_Webcam_HD as /devices/pci0000:00/0000:00:14.0/usb2/2-5/2-5:1.0/input/input16
[ 4503.943676] [drm] Enabling RC6 states: RC6 on, RC6p off, RC6pp off
[ 4506.058296] dell_wmi: Unknown key e00e pressed
[ 4507.048423] wlan0: authenticate with c0:25:06:84:57:f0
[ 4507.051164] wlan0: send auth to c0:25:06:84:57:f0 (try 1/3)
[ 4507.053766] wlan0: authenticated
[ 4507.056205] wlan0: associate with c0:25:06:84:57:f0 (try 1/3)
[ 4507.062403] wlan0: RX AssocResp from c0:25:06:84:57:f0 (capab=0x431 status=0 aid=1)
[ 4507.065241] wlan0: associated
[ 4507.065268] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 4812.948936] usb 2-2: new high-speed USB device number 6 using xhci_hcd
[ 4813.124097] hub 2-2:1.0: USB hub found
[ 4813.124371] hub 2-2:1.0: 4 ports detected
[ 4813.392831] usb 2-2.2: new full-speed USB device number 7 using xhci_hcd
[ 4813.477901] usb 2-2.2: ep 0x85 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 4813.495517] input: Burr-Brown from TI USB Audio CODEC as /devices/pci0000:00/0000:00:14.0/usb2/2-2/2-2.2/2-2.2:1.3/0003:08BB:2902.0003/input/input17
[ 4813.495657] hid-generic 0003:08BB:2902.0003: input,hidraw2: USB HID v1.00 Device [Burr-Brown from TI USB Audio CODEC ] on usb-0000:00:14.0-2.2/input3
[ 4813.515300] usbcore: registered new interface driver snd-usb-audio
[ 4813.546263] usb 2-2.3: new full-speed USB device number 8 using xhci_hcd
[ 4813.648070] logitech-djreceiver 0003:046D:C52B.0006: hiddev0,hidraw3: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:14.0-2.3/input2
[ 4813.699821] usb 2-2.4: new high-speed USB device number 9 using xhci_hcd
[ 4813.700997] input: Logitech Unifying Device. Wireless PID:1028 as /devices/pci0000:00/0000:00:14.0/usb2/2-2/2-2.3/2-2.3:1.2/0003:046D:C52B.0006/0003:046D:C52B.0007/input/input18
[ 4813.701200] logitech-djdevice 0003:046D:C52B.0007: input,hidraw4: USB HID v1.11 Mouse [Logitech Unifying Device. Wireless PID:1028] on usb-0000:00:14.0-2.3:1
[ 4814.121899] ax88179_178a 2-2.4:1.0 eth0: register 'ax88179_178a' at usb-0000:00:14.0-2.4, ASIX AX88179 USB 3.0 Gigabit Ethernet, 00:24:9b:0a:27:f6
[ 4814.121931] usbcore: registered new interface driver ax88179_178a
[ 4814.442429] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 4817.483762] ax88179_178a 2-2.4:1.0 eth0: ax88179 - Link status is: 1
[ 4817.485665] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 6509.605763] usb 2-2: USB disconnect, device number 6
[ 6509.605773] usb 2-2.2: USB disconnect, device number 7
[ 6509.660447] usb 2-2.3: USB disconnect, device number 8
[ 6509.692281] usb 2-2.4: USB disconnect, device number 9
[ 6509.692540] ax88179_178a 2-2.4:1.0 eth0: unregister 'ax88179_178a' usb-0000:00:14.0-2.4, ASIX AX88179 USB 3.0 Gigabit Ethernet
[ 6509.692573] ax88179_178a 2-2.4:1.0 eth0: Failed to read reg index 0x0002: -19
[ 6509.692584] ax88179_178a 2-2.4:1.0 eth0: Failed to write reg index 0x0002: -19
[ 6509.721655] ax88179_178a 2-2.4:1.0 (unregistered net_device): Failed to write reg index 0x0002: -19
[ 6509.721669] ax88179_178a 2-2.4:1.0 (unregistered net_device): Failed to write reg index 0x0001: -19
[ 6509.721678] ax88179_178a 2-2.4:1.0 (unregistered net_device): Failed to write reg index 0x0002: -19
[ 6511.071805] PM: Syncing filesystems ...
[ 6511.077462] atkbd serio0: Unknown key pressed (translated set 2, code 0xf2 on isa0060/serio0).
[ 6511.077473] atkbd serio0: Use 'setkeycodes e072 <keycode>' to make it known.
[ 6511.085453] atkbd serio0: Unknown key released (translated set 2, code 0xf2 on isa0060/serio0).
[ 6511.085464] atkbd serio0: Use 'setkeycodes e072 <keycode>' to make it known.
[ 6511.087129] done.
[ 6511.087139] PM: Preparing system for mem sleep
[ 6511.087676] Freezing user space processes ... (elapsed 0.001 seconds) done.
[ 6511.089183] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[ 6511.090294] PM: Entering mem sleep
[ 6511.090393] Suspending console(s) (use no_console_suspend to debug)
[ 6511.090786] wlan0: deauthenticating from c0:25:06:84:57:f0 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 6511.100925] cfg80211: Calling CRDA to update world regulatory domain
[ 6511.101532] sd 2:0:0:0: [sda] Synchronizing SCSI cache
[ 6511.101598] sd 2:0:0:0: [sda] Stopping disk
[ 6511.720807] PM: suspend of devices complete after 629.628 msecs
[ 6511.734165] PM: late suspend of devices complete after 13.343 msecs
[ 6511.734991] ehci-pci 0000:00:1d.0: System wakeup enabled by ACPI
[ 6511.735113] xhci_hcd 0000:00:14.0: System wakeup enabled by ACPI
[ 6511.747808] PM: noirq suspend of devices complete after 13.629 msecs
[ 6511.748271] ACPI: Preparing to enter system sleep state S3
[ 6511.749033] PM: Saving platform NVS memory
[ 6511.749584] Disabling non-boot CPUs ...
[ 6511.749628] intel_pstate CPU 1 exiting
[ 6511.751130] kvm: disabling virtualization on CPU1
[ 6511.752157] smpboot: CPU 1 is now offline
[ 6511.752650] intel_pstate CPU 2 exiting
[ 6511.754091] kvm: disabling virtualization on CPU2
[ 6511.754112] smpboot: CPU 2 is now offline
[ 6511.755147] intel_pstate CPU 3 exiting
[ 6511.756491] kvm: disabling virtualization on CPU3
[ 6511.857520] smpboot: CPU 3 is now offline
[ 6511.860099] ACPI: Low-level resume complete
[ 6511.860168] PM: Restoring platform NVS memory
[ 6511.860682] Enabling non-boot CPUs ...
[ 6511.860725] x86: Booting SMP configuration:
[ 6511.860726] smpboot: Booting Node 0 Processor 1 APIC 0x1
[ 6511.873161] kvm: enabling virtualization on CPU1
[ 6511.875384] Intel pstate controlling: cpu 1
[ 6511.875441] CPU1 is up
[ 6511.875462] smpboot: Booting Node 0 Processor 2 APIC 0x2
[ 6511.887813] kvm: enabling virtualization on CPU2
[ 6511.890055] Intel pstate controlling: cpu 2
[ 6511.890104] CPU2 is up
[ 6511.890121] smpboot: Booting Node 0 Processor 3 APIC 0x3
[ 6511.902450] kvm: enabling virtualization on CPU3
[ 6511.904715] Intel pstate controlling: cpu 3
[ 6511.904763] CPU3 is up
[ 6511.910077] ACPI: Waking up from system sleep state S3
[ 6511.930462] ehci-pci 0000:00:1d.0: System wakeup disabled by ACPI
[ 6511.930469] xhci_hcd 0000:00:14.0: System wakeup disabled by ACPI
[ 6511.930713] PM: noirq resume of devices complete after 11.834 msecs
[ 6511.931215] PM: early resume of devices complete after 0.474 msecs
[ 6511.931290] mei_me 0000:00:16.0: irq 58 for MSI/MSI-X
[ 6511.931308] usb usb2: root hub lost power or was reset
[ 6511.931310] usb usb3: root hub lost power or was reset
[ 6511.932049] snd_hda_intel 0000:00:1b.0: irq 59 for MSI/MSI-X
[ 6512.019117] xhci_hcd 0000:00:14.0: irq 56 for MSI/MSI-X
[ 6512.030458] sd 2:0:0:0: [sda] Starting disk
[ 6512.143743] iwlwifi 0000:02:00.0: L1 Enabled; Disabling L0S
[ 6512.143995] iwlwifi 0000:02:00.0: L1 Enabled; Disabling L0S
[ 6512.237297] usb 1-1: reset high-speed USB device number 2 using ehci-pci
[ 6512.350707] ata3: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 6512.353607] ata3.0Update: I mucked about more after making this post; I installed gnome-alsa-mixer and checked the "internal mic" option and "Auto-Mute mode" (both were off), after this my headphone output works again, and does the built-in microphone (!)
I have no idea how I ended up in this "broken" situation, or even what this option does, or how to use it without gnome-alsa-mixer (I had to install 15 packages to get this, as I normally don't use gnome)... Sound on Linux still seems no better than when I started using it 15 years ago :-( (I spent about 5 hours on this...) -
AE CS6 Renders Stop after 325 frames.
AE CS6 Renders Stop after 325 frames - or nearly: they abruptly start slowing down to 1 frame every 30 seconds until they hit a standstill, as the amount of RAM in use starts climbing suddenly until it reaches around 67%, at which point it is dead.
I'm on AE CS6 Version 11.0, freshly downloaded from the Cloud.
I am on a MacBook Pro 5,3 running Mac OSX Lion 10.7.5 with a 3.06 GHz IntelCore 2 Duo processor and an NVidia GeForce 9400M 256MB Card.
I've maxed out the RAM at 8 GB. I'm using Quicktime Player 7.6.6 (the most up to date).
I'm just rendering a 2D Comp to Quicktime/Photo JPEG Codec with an aspect ratio of 960x540. The comp is simple: a 1.6 MB jpg with a slight scale-up and a Liquify effect for a duration of about 4 minutes 30 (interestingly, the render stop occurs about 15 seconds before the Liquify effect starts.)
I've tried this with "Render Multiple Frames Simultaneously" on and off with no difference. However, when it's on, Installed CPUs reads 2 and Reserved for other apps reads 0 and AE will not let me change it. Also, Ram Allocation per Background CPU has been tried at everything from 1 GB to 3 GB. Actual CPUs used is set to 0, and I cannot change it either.
I have no other apps open during rendering. And there can't be a bus issue, since the AE project, the source jpg and the output location are all in the Documents folder on my hard drive. I'm at a loss. Any ideas or suggestions?
ThanksThis had an interesting result: the percentage of RAM in use no longer goes through the roof but tops out at 13%. The render does not stop but goes painfully slowly. At 24 hours of render time, I've now gotten to frame 1470 of 8114. Estimated time to completion now reads 109 hours.
As I mentioned before: I'm just rendering a 2D Comp to Quicktime/Photo JPEG Codec with an aspect ratio of 960x540. The comp is simple: a 1.6 MB jpg with a slight scale-up and a Liquify effect for a duration of about 4 minutes 30.
Or does liquify just take this much processing power? -
How to process an output message after pick and pack in LM46?
Hi,
I've implemented the User Exit to print the HU using LM18, it's working great but no output message is processed (and indeed, the sticker is printed on my own printer instead of the one defined in my Z custom output message).
I used LM46 to pick and pack the HU, am i missing a step?
In other words, how to process my custom output message after the pick and pack?
Is there some code I must add in the LM18 User Exit?You know, in a user exit or a BADi you can access any variable of the program you want.
Just find what which program calls the Exit User, put a break-point in it, and find the variable you need to access.
Then add this kind code in your Exit :
DATA: l_var TYPE ....
FIELD-SYMBOLS: <fs_var> TYPE ANY.
ASSIGN ('(PGMNAME)variable') TO <fs_var>.
IF sy-subrc = 0.
l_var = <fs_var>.
ENDIF.
Same thing for a table :
DATA: lt_var TYPE TABLE OF....
FIELD-SYMBOLS: <fs_var> TYPE ANY.
ASSIGN ('(PGMNAME)table[]') TO <fs_var>.
IF sy-subrc = 0.
lt_var[] = <fs_var>.
LOOP AT lt_var ASSIGNING ...
ENDLOOP.
ENDIF. -
Execution stops after retrieving the factory from the ServletContext while
Hi,
I just started working with Quartz, so I am clueless as to why I am getting this error. This is my first time tying to integrate Quartz 1.6.0 in a web app. I am using the JSF Framework. Although I have added the necessary jars I am still getting the error above: servlet.jar not loaded. If you follow the java code and server output you can see that after retrieving the factory from the ServletContext there is no further execution . Following is the definition of the class used for scheduling:
Quartz Version: 1.6.0
IDE : Netbeans 5.0
AppServer: Tomcat 5.5
*************************************** JAVA CODE *************************************
* BirthdayScheduler.java
* Created on May 20, 2008, 5:24 PM
package com.csg.cs.cscomwebdev.servlet.timer;
import java.io.*;
import java.net.*;
import java.util.Date;
import javax.servlet.*;
import javax.servlet.http.*;
import org.quartz.JobDetail;
import org.quartz.SchedulerException;
import org.quartz.SimpleTrigger;
import org.quartz.impl.StdSchedulerFactory;
import org.quartz.Scheduler;
* @author Arijit Datta
* @version
public class BirthdayScheduler extends HttpServlet {
/** Processes requests for both HTTP <code>GET</code> and <code>POST</code> methods.
* @param request servlet request
* @param response servlet response
protected void processRequest(HttpServletRequest request, HttpServletResponse response)
throws ServletException, IOException {
response.setContentType("text/html;charset=UTF-8");
PrintWriter out = response.getWriter();
out.close();
/** Handles the HTTP <code>GET</code> method.
* @param request servlet request
* @param response servlet response
protected void doGet(HttpServletRequest request, HttpServletResponse response)
throws ServletException, IOException {
processRequest(request, response);
/** Handles the HTTP <code>POST</code> method.
* @param request servlet request
* @param response servlet response
protected void doPost(HttpServletRequest request, HttpServletResponse response)
throws ServletException, IOException {
processRequest(request, response);
/** Returns a short description of the servlet.
public String getServletInfo() {
return "Short description";
public void init()
System.out.println(" ------------ STARTTING JOB --------------");
// Retrieve the ServletContext
ServletContext theApplicationsServletContext = this.getServletContext();
// Retrieve the factory from the ServletContext
StdSchedulerFactory factory =(StdSchedulerFactory)theApplicationsServletContext.getAttribute("QuartzFactory Servlet.QUARTZ_FACTORY_KEY");
System.out.println(" ------------ FACTORY GOT --------------");
try {
// Retrieve the scheduler from the factory
Scheduler scheduler = factory.getScheduler();
System.out.println(" ------------ SCHEDULER GOT --------------");
// Start the scheduler
scheduler.start();
System.out.println(" ------------ SCHEDULER STARTED --------------");
//Creating a job
JobDetail birthdayJobDetail = new JobDetail("birthdayReminderJob", scheduler.DEFAULT_GROUP, BirthdayReminderJob.class );
System.out.println(" ------------ JOB CREATED --------------");
//Creating a trigger
SimpleTrigger birthdayJobtrigger = new SimpleTrigger("birthdayReminderTrigger",scheduler.DEFAULT_GROUP, new Date(),null,SimpleTrigger.REPEAT_INDEFINITELY, 60L * 1000L);
System.out.println(" ------------ TRIGGER CREATED --------------");
//Scheduling the job
scheduler.scheduleJob(birthdayJobDetail,birthdayJobtrigger );
System.out.println(" ------------ JOB SCHEDULED --------------");
} catch (SchedulerException ex) {
System.out.println(ex.getMessage());
} ************************************* SECTION OF WEB.XML ************************
<servlet>
<description>Quartz Initializer Servlet</description>
<servlet-name>QuartzInitializer</servlet-name>
<servlet-class>org.quartz.ee.servlet.QuartzInitializerServlet</servlet -class>
<init-param>
<param-name>shutdown-on-unload</param-name>
<param-value>true</param-value>
</init-param>
<init-param>
<param-name>start-scheduler-on-load</param-name>
<param-value>true</param-value>
</init-param>
<load-on-startup>1</load-on-startup>
</servlet>
<servlet>
<servlet-name>BirthdayScheduler</servlet-name>
<servlet-class>com.csg.cs.cscomwebdev.servlet.timer.BirthdayScheduler< /servlet-class>
<load-on-startup>1</load-on-startup>
</servlet> *********************************** SERVER OUTPUT *******************************
Using CATALINA_BASE: C:\Documents and Settings\165171\.netbeans\5.0\jakarta-tomcat-5.5.9_base
Using CATALINA_HOME: D:\Program Files\netbeans-5.0\enterprise2\jakarta-tomcat-5.5.9
Using CATALINA_TMPDIR: C:\Documents and Settings\165171\.netbeans\5.0\jakarta-tomcat-5.5.9_base\temp
Using JAVA_HOME: C:\Program Files\Java\jdk1.5.0_02
May 20, 2008 7:27:13 PM org.apache.coyote.http11.Http11Protocol init
INFO: Initializing Coyote HTTP/1.1 on http-8084
May 20, 2008 7:27:13 PM org.apache.catalina.startup.Catalina load
INFO: Initialization processed in 766 ms
May 20, 2008 7:27:13 PM org.apache.catalina.core.StandardService start
INFO: Starting service Catalina
May 20, 2008 7:27:13 PM org.apache.catalina.core.StandardEngine start
INFO: Starting Servlet Engine: Apache Tomcat/5.5.9
May 20, 2008 7:27:13 PM org.apache.catalina.core.StandardHost start
INFO: XML validation disabled
May 20, 2008 7:27:14 PM org.apache.catalina.loader.WebappClassLoader validateJarFile
INFO: validateJarFile(D:\Java Programs\cs\CSCOMWEBDEV\build\web\WEB-INF\lib\servlet.jar) - jar not loaded. See Servlet Spec 2.3, section 9.7.2. Offending class: javax/servlet/Servlet.class
log4j:WARN No appenders could be found for logger (org.apache.catalina.session.ManagerBase).
log4j:WARN Please initialize the log4j system properly.
------------ STARTTING JOB --------------
------------ FACTORY GOT --------------
May 20, 2008 7:27:15 PM org.apache.coyote.http11.Http11Protocol start
INFO: Starting Coyote HTTP/1.1 on http-8084
May 20, 2008 7:27:15 PM org.apache.jk.common.ChannelSocket init
INFO: JK: ajp13 listening on /0.0.0.0:8009
May 20, 2008 7:27:15 PM org.apache.jk.server.JkMain start
INFO: Jk running ID=0 time=0/32 config=null
May 20, 2008 7:27:15 PM org.apache.catalina.storeconfig.StoreLoader load
INFO: Find registry server-registry.xml at classpath resource
May 20, 2008 7:27:16 PM org.apache.catalina.startup.Catalina start
INFO: Server startup in 2802 ms Can anybody please help out? Where exactly am I going wrong?
Thanks a lot!
ADYour stop condition is "continue if true". This means that, unless you press the button, the while loop will stop after one iteration.
First, you should change the termination condition to "stop if true".
Then you should make the stop button "latch when released" (right-click..mechanical action). Else you don't have a well defined state after the program stops.
You should decide on a reasonable loop rate and enter it for the wait control. (beter use a diagram constant if the value is always the same).
Why do you need to continue reading in a loop? Are you expecting the response to change over time?
Do you want to keep appending to the string indicator or only show the latest characters received?
Maybe you also need a wait between the writing and reading?
Delete the ms timer value indicator, it is completely useless.
Do you get any error codes?
Don't use the run continous button. Use the plain run button.
What device are you communicating with? Do you have documentation?
LabVIEW Champion . Do more with less code and in less time . -
Reading the output values after each step executes in LabVIEW User Interface
Hello all,
Development environment: TestStand 2010 SP1 and LabVIEW 2010 SP1
Problem: is there a way to execute the subsequent steps programatically and get the output values from each of them?
I have already extended a little bit a Full OI interface for TestStand to load up any sequence, choose some of the steps and run them step by step (something like option to Run Selected steps). What I am trying to do is to add some actions between each step and do that in User Interface (I can't modify the sequence!), so I am starting the NewExecution with some previously configured InteractiveArgsParam and set an option breakAtFirstStep to True. Afterwards I am just doing something like Step Over when debugging the sequence and this works good, but I didn't fine a way yet to read the output values from the steps...
Then, if I wait until the execution finishes I can read my Results by processing the ResultObject, but this works only after finalizing of the test sequence. Since I wanted to stop after each step, read the values, do some actions and continue to the next step I tried to register an event callback for Trace of Execution View Manager. I can see that after each executed step this event is triggered, but when I try to read a ResultObject returned in Event Data it is not filled with values (ResultList seems to be empty?). Is it a proper behaviour or maybe I am doing the readout in wrong way? (It is the same VI as for reading ResultObjects after sequence finishes and there it works fine for arrays, containers and other data types).
Like I mentioned I can't modify the Test sequences, I can't add a UImessages.
What are my options? Should the trace event returns all output values from each steps or is it just used for status checking? Or maybe there is completely different approach to that matter?
Thanks in advance for any suggestions,
Best Regards.
CLA, CTD, CLED @ Test & Measurements Solutions Poland
Solved!
Go to Solution.Thanks for your replay, I have tried to build it in my LabView Block Diagramm, es seems like this image.
But the variable GetNumSubProperties ist always 0. Why?
PS: I need only the variable "Step.Result.PassFail" from the last step, do you know, how can I get it? I think, it is maybe easier than read all the "Result".
Attachments:
ReadStepResultInLabview.JPG 39 KB -
How to remove zero after decimal point.
hi friends
how to remove the zero after decimal points.
example :
123.450 -- if print only 123.45
45.600 - 45.6
any body help me.
thanks
pauldhamago through this example
it may help u
DATA: T(14) VALUE ' abcdefghij',
STRING LIKE T,
STR(6) VALUE 'ghijkl'.
STRING = T.
WRITE STRING.
SHIFT STRING LEFT DELETING LEADING SPACE (or use 0 to detete 0).
WRITE / STRING.
STRING = T.
SHIFT STRING RIGHT DELETING TRAILING STR or 0.
WRITE / STRING.
Output:
abcdefghij
abcdefghij
abcdef -
Report is executing in background and need data(output) in excel format
Report is executing in background and need data(output) to get downloaded in excel format in my PC from an internal table;;in any drive i.e. C: or D: .When executing in backround it prompt to user with which location excel file to be saved and the name of file.How to download in background in excel format?
Edited by: PRASHANT BHATNAGAR on Aug 26, 2008 6:24 AMHi
Download a report to excel with format (border, color cell, etc)
Try this program...it may help you to change the font ..etc.
Code:
REPORT ZSIRI NO STANDARD PAGE HEADING.
this report demonstrates how to send some ABAP data to an
EXCEL sheet using OLE automation.
INCLUDE OLE2INCL.
handles for OLE objects
DATA: H_EXCEL TYPE OLE2_OBJECT, " Excel object
H_MAPL TYPE OLE2_OBJECT, " list of workbooks
H_MAP TYPE OLE2_OBJECT, " workbook
H_ZL TYPE OLE2_OBJECT, " cell
H_F TYPE OLE2_OBJECT. " font
TABLES: SPFLI.
DATA H TYPE I.
table of flights
DATA: IT_SPFLI LIKE SPFLI OCCURS 10 WITH HEADER LINE.
*& Event START-OF-SELECTION
START-OF-SELECTION.
read flights
SELECT * FROM SPFLI INTO TABLE IT_SPFLI UP TO 10 ROWS.
display header
ULINE (61).
WRITE: / SY-VLINE NO-GAP,
(3) 'Flg'(001) COLOR COL_HEADING NO-GAP, SY-VLINE NO-GAP,
(4) 'Nr'(002) COLOR COL_HEADING NO-GAP, SY-VLINE NO-GAP,
(20) 'Von'(003) COLOR COL_HEADING NO-GAP, SY-VLINE NO-GAP,
(20) 'Nach'(004) COLOR COL_HEADING NO-GAP, SY-VLINE NO-GAP,
(8) 'Zeit'(005) COLOR COL_HEADING NO-GAP, SY-VLINE NO-GAP.
ULINE /(61).
display flights
LOOP AT IT_SPFLI.
WRITE: / SY-VLINE NO-GAP,
IT_SPFLI-CARRID COLOR COL_KEY NO-GAP, SY-VLINE NO-GAP,
IT_SPFLI-CONNID COLOR COL_NORMAL NO-GAP, SY-VLINE NO-GAP,
IT_SPFLI-CITYFROM COLOR COL_NORMAL NO-GAP, SY-VLINE NO-GAP,
IT_SPFLI-CITYTO COLOR COL_NORMAL NO-GAP, SY-VLINE NO-GAP,
IT_SPFLI-DEPTIME COLOR COL_NORMAL NO-GAP, SY-VLINE NO-GAP.
ENDLOOP.
ULINE /(61).
tell user what is going on
CALL FUNCTION 'SAPGUI_PROGRESS_INDICATOR'
EXPORTING
PERCENTAGE = 0
TEXT = TEXT-007
EXCEPTIONS
OTHERS = 1.
start Excel
CREATE OBJECT H_EXCEL 'EXCEL.APPLICATION'.
PERFORM ERR_HDL.
SET PROPERTY OF H_EXCEL 'Visible' = 1.
CALL METHOD OF H_EXCEL 'FILESAVEAS' EXPORTING #1 = 'c:\kis_excel.xls'
PERFORM ERR_HDL.
tell user what is going on
CALL FUNCTION 'SAPGUI_PROGRESS_INDICATOR'
EXPORTING
PERCENTAGE = 0
TEXT = TEXT-008
EXCEPTIONS
OTHERS = 1.
get list of workbooks, initially empty
CALL METHOD OF H_EXCEL 'Workbooks' = H_MAPL.
PERFORM ERR_HDL.
add a new workbook
CALL METHOD OF H_MAPL 'Add' = H_MAP.
PERFORM ERR_HDL.
tell user what is going on
CALL FUNCTION 'SAPGUI_PROGRESS_INDICATOR'
EXPORTING
PERCENTAGE = 0
TEXT = TEXT-009
EXCEPTIONS
OTHERS = 1.
output column headings to active Excel sheet
PERFORM FILL_CELL USING 1 1 1 'Flug'(001).
PERFORM FILL_CELL USING 1 2 0 'Nr'(002).
PERFORM FILL_CELL USING 1 3 1 'Von'(003).
PERFORM FILL_CELL USING 1 4 1 'Nach'(004).
PERFORM FILL_CELL USING 1 5 1 'Zeit'(005).
LOOP AT IT_SPFLI.
copy flights to active EXCEL sheet
H = SY-TABIX + 1.
PERFORM FILL_CELL USING H 1 0 IT_SPFLI-CARRID.
PERFORM FILL_CELL USING H 2 0 IT_SPFLI-CONNID.
PERFORM FILL_CELL USING H 3 0 IT_SPFLI-CITYFROM.
PERFORM FILL_CELL USING H 4 0 IT_SPFLI-CITYTO.
PERFORM FILL_CELL USING H 5 0 IT_SPFLI-DEPTIME.
ENDLOOP.
changes by Kishore - start
CALL METHOD OF H_EXCEL 'Workbooks' = H_MAPL.
CALL METHOD OF H_EXCEL 'Worksheets' = H_MAPL." EXPORTING #1 = 2.
PERFORM ERR_HDL.
add a new workbook
CALL METHOD OF H_MAPL 'Add' = H_MAP EXPORTING #1 = 2.
PERFORM ERR_HDL.
tell user what is going on
SET PROPERTY OF H_MAP 'NAME' = 'COPY'.
CALL FUNCTION 'SAPGUI_PROGRESS_INDICATOR'
EXPORTING
PERCENTAGE = 0
TEXT = TEXT-009
EXCEPTIONS
OTHERS = 1.
output column headings to active Excel sheet
PERFORM FILL_CELL USING 1 1 1 'Flug'(001).
PERFORM FILL_CELL USING 1 2 0 'Nr'(002).
PERFORM FILL_CELL USING 1 3 1 'Von'(003).
PERFORM FILL_CELL USING 1 4 1 'Nach'(004).
PERFORM FILL_CELL USING 1 5 1 'Zeit'(005).
LOOP AT IT_SPFLI.
copy flights to active EXCEL sheet
H = SY-TABIX + 1.
PERFORM FILL_CELL USING H 1 0 IT_SPFLI-CARRID.
PERFORM FILL_CELL USING H 2 0 IT_SPFLI-CONNID.
PERFORM FILL_CELL USING H 3 0 IT_SPFLI-CITYFROM.
PERFORM FILL_CELL USING H 4 0 IT_SPFLI-CITYTO.
PERFORM FILL_CELL USING H 5 0 IT_SPFLI-DEPTIME.
ENDLOOP.
changes by Kishore - end
disconnect from Excel
CALL METHOD OF H_EXCEL 'FILESAVEAS' EXPORTING #1 = 'C:\SKV.XLS'.
FREE OBJECT H_EXCEL.
PERFORM ERR_HDL.
FORM FILL_CELL *
sets cell at coordinates i,j to value val boldtype bold *
FORM FILL_CELL USING I J BOLD VAL.
CALL METHOD OF H_EXCEL 'Cells' = H_ZL EXPORTING #1 = I #2 = J.
PERFORM ERR_HDL.
SET PROPERTY OF H_ZL 'Value' = VAL .
PERFORM ERR_HDL.
GET PROPERTY OF H_ZL 'Font' = H_F.
PERFORM ERR_HDL.
SET PROPERTY OF H_F 'Bold' = BOLD .
PERFORM ERR_HDL.
ENDFORM.
*& Form ERR_HDL
outputs OLE error if any *
--> p1 text
<-- p2 text
FORM ERR_HDL.
IF SY-SUBRC <> 0.
WRITE: / 'Fehler bei OLE-Automation:'(010), SY-SUBRC.
STOP.
ENDIF.
ENDFORM. " ERR_HDL
Regards
Murali Papana -
After upgrade to 10.8.1, Internet access stops after approx. 50MB of traffic.
I upgraded to Mountain Lion, and when I started upgrading OS components and other apps, downloads would stop after about 50MB. Once this happens, all requests in internet browsers also lost internet access. If I turn Airport off and then on again, I can access the internet but the same problem occurs again once I continue other downloads.
I have other computers and they don't suffer from this problem, so I know if is not my internet provider or my wireless network.
Any ideas?Me too! I'm also getting display problems in emails where scrambled graphics are overlaid interactive parts of emails like dates telephone numbers!
-
Call export with java function stop after a time
Hi
we make a function java for call exp.exe.
We pass at java's function a string
we use this code
/* * ExecuteCmd.java * This is a sample application that uses the Runtime Object * to execute a program. * */
/* Import the classes needed for Runtime, Process, and Exceptions */
import java.lang.*;
//import java.lang.Process;
import java.io.*;
//import java.lang.InterruptedException;
class ExecuteCmd {
public static int Cmd(String args) {
try {
/* Execute the command using the Runtime object and get the
Process which controls this command */
Process p = Runtime.getRuntime().exec(args);
/* Use the following code to wait for the process to finish
and check the return code from the process */
try {
p.waitFor();
/* Handle exceptions for waitFor() */
} catch (InterruptedException intexc) {
//System.out.println("Interrupted Exception on waitFor: " + intexc.getMessage());
return -1;
return p.exitValue();
/* Handle the exceptions for exec() */
} catch (IOException e) {
// System.out.println("IO Exception from exec : " + e.getMessage());
// e.printStackTrace();
return 1;
after a time the export begin but stop after some time.
If the schema is little like not table but some sequence the export gone normally but if the schema is big the export stop after a time but we dont have a trace with log.
Can you helpI think you need to gobble up the output from the command you are exec'ing. If the exec'd command fills up your command space buffer it will stop when the buffer is full.
Try adding the lines
String s = new String();
while ((s = p.readLine())!=null)
after the try block to gobble up the output from your command call. -
IPod Classic Starts to Sync But Stops After 5 Seconds
I'd appreciate help with this...
Two days ago, my iPod Classic stopped syncing. I don't think this is the situation where the device is not recognized. When I connect with the USB, the iPod appears in iTunes and it starts to sync but then stops after about 5 seconds. I have the latest iTunes (11.0.5) and iPod software; I re-set the iPod; and I ran a check for errors on the iPod, but it came back clean; I can't erase the latest backup in Properties because it's empty.
Here's what I don't understand - I ran a diagnostic on the connection but it was ok; when I ran a diagnostic on sync, it said no iPod was found -- even though I had the same connection when I ran the diagnostic a few seconds earlier. I know that the iPod is recognized because I can drag podcasts onto the iPod when it's connected.
Any ideas? I'd rather not have to reinstall iTunes.
Microsoft Windows 7 x64 Home Premium Edition Service Pack 1 (Build 7601)
ASUSTeK COMPUTER INC. X75VD
iTunes 11.0.5.5
QuickTime 7.7.2
FairPlay 2.4.14
Apple Application Support 2.3.4
iPod Updater Library 10.0d2
CD Driver 2.2.3.0
CD Driver DLL 2.1.3.1
Apple Mobile Device 6.1.0.13
Apple Mobile Device Driver 1.64.0.0
Bonjour 3.0.0.10 (333.10)
Gracenote SDK 1.9.6.502
Gracenote MusicID 1.9.6.115
Gracenote Submit 1.9.6.143
Gracenote DSP 1.9.6.45
iTunes Serial Number 0026B5780A1E41A0
Current user is not an administrator.
The current local date and time is 2013-08-24 22:33:39.
iTunes is not running in safe mode.
WebKit accelerated compositing is enabled.
HDCP is supported.
Core Media is supported.
Video Display Information
NVIDIA, NVIDIA GeForce 610M
Intel Corporation, Intel(R) HD Graphics 4000
**** External Plug-ins Information ****
No external plug-ins installed.
**** Device Connectivity Tests ****
iPodService 11.0.5.5 (x64) is currently running.
iTunesHelper 11.0.5.5 is currently running.
Apple Mobile Device service 3.3.0.0 is currently running.
Universal Serial Bus Controllers:
Intel(R) 7 Series/C216 Chipset Family USB Enhanced Host Controller - 1E26. Device is working properly.
Intel(R) 7 Series/C216 Chipset Family USB Enhanced Host Controller - 1E2D. Device is working properly.
Intel(R) USB 3.0 eXtensible Host Controller. Device is working properly.
No FireWire (IEEE 1394) Host Controller found.
Connected Device Information:
ALLIE'S IPO (E:\), iPod classic running firmware version 2.0.4
Serial Number: 8K027FWS9ZU
Bus Speed: 61440
Most Recent Devices Not Currently Connected:
iPhone 4S running firmware version 6.1.3
Serial Number: C38GF4D7DTF9
**** Device Sync Tests ****
No iPod, iPhone, or iPad found.Hi,
I had a similar problem, all you can do at present to rectify this is to grab your playlist or new created playlist or song from the main library or playlist and drop it into the ipod tab under devices and it will auto sync the changes or songs. Hope this helps.
There seems to be a problem with the syncing of itunes 11 (mine is 11.0.5) when you just use the normal sync method. the above should work and has worked for me when transfering a playlist straight into the ipod it automatically syncs.
Regards.
Nick -
Flash movies stop after a random amount of time,
The problem that I am having is that flash movie files (Every website) play for a moment or two and then stop with the little “loading” symbol turning endlessly in the center of the screen. Flash movies used to work with no problem but over the span of the last few months it went from not working well to not working at all. In a perhaps related problem sometimes downloads will stop after a certain length of time and also seem to “hang” at a random spot. If I pause the reload and then restart it the program or whatever will usually finish downloading. This doesn’t happen often but does happen. The flash movie thing, though, happens every time – no matter what browser I have tried. (Firefox, IE, IE with no add-ons, and Chrome anyway.)
I have tried solutions that I have found all across the internet, including the Adobe and Microsoft forums, to no avail. I have unloaded flash with the Adobe uninstaller and reloaded flash. I have tried various flash releases – with and without a firewall on. I have made sure that I am using the 32 bit version of IE and even tried running everything in “administrator mode.” I’ve upgraded every driver that I can upgrade. I’ve used a registry checker as a last resort. I even used the Dell partition to return my computer back to the condition that it was in when I bought it and that didn’t change anything either.
Everything I have tried has made zero difference. In the hopes that someone will have another idea for me to try I am putting all the stats for my computer that I can think of below.
Qwest internet running at 20mbps
Flash 10.1.102.64
Shockwave 11.5.9.615
Microsoft Security Essentials
Tried both IE 9, IE with no add-ons, and now have IE 8 from when I restored from the partition image
OS Name Microsoft Windows 7 Home Premium
Version 6.1.7600 Build 7600
System Manufacturer Dell Inc.
System Model Inspiron 560
System Type x64-based PC
Processor Intel(R) Core(TM)2 Duo CPU E7500 @ 2.93GHz, 2936 Mhz, 2 Core(s), 2 Logical Processor(s)
Graphics - Intel(R) G45/G43 Express Chipset
Sound - Realtek High Definition Audio
BIOS Version/Date Dell Inc. A00, 10/6/2009
SMBIOS Version 2.6
Hardware Abstraction Layer Version = "6.1.7600.16385"
Installed Physical Memory (RAM) 8.00 GB
Total Physical Memory 7.96 GB
Available Physical Memory 6.94 GB
Total Virtual Memory 15.9 GB
Available Virtual Memory 14.4 GB
Page File Space 7.96 GBThank you for answering eidnolb -
Answering your questions...
Have you had a Virus and if so what Anti-Virus program removed it?
No virus that I am aware of
Since you have a Dell, McAfee came pre-installed? Did you remove it prior to Installing MSE? If so, did you use the McAfee Removal Tool or just remove it from Control Panel/Programs & Features?
My computer did come with McAfee which isn't on my computer now. I used a program called "Decrapifier" that removes unwanted preloaded software that comes with PCs.
Is McAfee still Installed?
No
Do you have any Anti-Virus/Spyware programs other than MSE?
No - I have just used MSE until now. I thought about using AVAST but was't sure what running 2 virus/spyware programs would be like.
Since MSE doesn't have a Firewall, do you use any Firewall other than Windows? If so, which?
I use Windows Firewall. I have tried both adding Youtube as an allowed program and switching the firewall off enirely with no luck.
Do you use a Router? Is it Wireless?
I do have a Lynksys router that is a little older but I've also tried hooking the modem directly to the computer.
Is Qwest wireless?
I use the wired ports and not the wireless for my connection.
Other than IE8, what browsers and versions are Installed now?
I only have IE8 now. I never reinstalled the other browsers after using the Dell partition. I prefer Firefox so having to use IE is frustrating.
I've also used "RegestryBooster" to make sure that my regestry looked okay.
Thanks again for taking the time to answer. I think you are right about me doing too much - LOL
Maybe you are looking for
-
Oracle apps forms doesnot load froom java
Hi My ebiz version is oracle appications r12.1.3 with 11.2.0.3 database When i click the security >user_define for opening the forms the forms windows doesnot appear JAVA doesnot load and i dont see any java icon on the bottom right corner of my syst
-
Common 3rd Party Jars in an EAR
Hi I have some common 3rd party jars and zips that are accessed by my WARs and EJB JARs. Where in my EAR structure do i place them so that these common jars like classes12, formulaone etc can be accessed from within my WARs and EJB jars? Regards Sudh
-
BB App World Version 3.1.0.58 updated and is not working. Error Message seeking identity installation keeps failing to install. How do I solve this problem?
-
RoboHelp 8 & Chrome - webhelp displays more than once
Robohelp 8 (up-to-date on patches) Webhelp - context sensitive Problem when using Chrome When a user clicks on a help link, the webhelp page displays. If the user opens another dialog in the application, the webhelp page displays again. While not cri
-
Is iTunes Restore error code 1 or -1 a hardware issue?
Hi there! I have been having network issuues with my iPhone 4S (the carrier name is stuck at "searching...") so i decided to restore the phone. But it ends with an error code (1). Is this to do with hardware or can be fixed through software. Thanks,