Data Collection 5.2 LMS 3.2 running always

why??
Best Regards.

Most likely "CSCtd49439 Data Collection never completes, and UT acquisition cannot run " which affects the CM 5.2. TAC could provide you patch or you need upgrade your CampusManager to 5.2.2.

Similar Messages

Data collection problems in LMS 4.0

Hi, we have some devices in our LMS 4.0 where Data Collection cannot be collected. The strange thing is that some days ago they were working fine and we have SNMP connectivity. We have deleted the devices and have added them again but the problem still persists, how can we fix it?

From the LMS server do the following:
1. ping the devices that you cannot collect their data
2. test the snmp connection to those devices using snmpwalk
go to CSCOpx\objects\jt\bin
snmpwalk -v 2c -c 1.3.6.1.2.1.1.2
3. test the credintials against those devices (Inventory> Job Browsers> Device Credentials Verification)
For any failure in 1 or 2 usually this is a firewall problem. Check if snmp and icmp ports are open or not.
For 3 failue check the credintials from (Inventory> Device Administration> Add / Import / Manage Devices)
I hope this help

For Lenovo anon data collection - what are good apps to run to help improve? (K1 but all really.)

In the spirit of helping Lenovo improve software/firmware, are there apps I should be running a lot so they can collect data that will contribute toward improvements? I assume anything streaming would help like Netflix.

jay1981 wrote:
I own a dvd business and would like to use it.
//Create new DVD objects and add them to the inventory
DVD theDVD = new DVD("Good Luck Chuck", "Comedy", "1", 10, 19.99);
theInventoryGUI.addDVDToInventory(theDVD);
theDVD = new DVD("The Bourne Identity", "Action Adventure", "2", 20, 15.49);
theInventoryGUI.addDVDToInventory(theDVD);
theDVD = new DVD("The Reaping", "Horror", "3", 13, 15.99);
theInventoryGUI.addDVDToInventory(theDVD);
theDVD = new DVD("Deja Vu", "Action", "4", 17, 14.49);
theInventoryGUI.addDVDToInventory(theDVD);Bad luck if the customer wants anything other than those 4 DVD's

Can we run parallel data collections to collect multiple source instance.

Hi,
We have a business requirement where we will have multiple Source(ERP) instance and single Destination(ASCP) instance. We would like to check if we will be able to run Data collections in parallel to collect multiple EPR instance in the same time window. This is to reduce the total planning process time duration as following data collections we will be required to run multiple plan runs.
Please help me with your expert comments
Rgds
Sid

You may instead use Continuous collections to save on time so it can run collections from both instances periodically throughout the day thereby reducing a single timespan to collect all the data.
Thanks
Navneet Goel
Inspirage

Problems with Data collection in CM 5.0.6

Hello:
I have installed LMS 3.0.1 and CM 5.0.6, and I have some problems with CM:
-Although data collection is scheduled, this does not run.
I try to launch it from CM menu, it asks if I want the collection of all devices or the new ones.
I try the two options but it does not do anything.
-I can launch the UT acquisition but it does not collect all the hosts.
I compare the configuration of the devices that "works" and the others and dont see no difference.
-The UT acquisition does not discover our Ip phones.
-In data collection settings there are 5 devices that are included but not managed.
-When I restart the server the data collection works fine, but the next day it doesn't work.
Thanks!!!

Hi,
As suspected, Campus Manager 5.0.6 hitting a bug as found the following exception in ani.log :-
2011/03/14 15:05:40 Discovery ani ERROR AniTimeLine: TimeBase Discovery caught exception: java.lang.NullPointerException
java.lang.NullPointerException
    at com.objectspace.jgl.HashMap.put(HashMap.java)
    at com.cisco.nm.ani.server.core.PortDetailsXml.populatePortData(PortDetailsXml.java:109)
    at com.cisco.nm.ani.server.core.DiscoveryTimeBaseImpl.generatePortDetailsXml(DiscoveryTimeBaseImpl.java:104)
    at com.cisco.nm.ani.server.core.DiscoveryTimeBaseImpl.postPerformScheduledFunction(DiscoveryTimeBaseImpl.java:81)
    at com.cisco.nm.ani.server.frontend.AniTimeBaseImpl.execute(AniTimeBaseImpl.java:48)
    at com.cisco.nm.ani.server.frontend.AniTimeLine.executeTimeBase(AniTimeLine.java:317)
    at com.cisco.nm.ani.server.frontend.AniTimeLine.runSchedule(AniTimeLine.java:350)
    at com.cisco.nm.ani.server.frontend.AniTimeLine.run(AniTimeLine.java:366)
    at java.lang.Thread.run(Thread.java:595)
BUG ID = CSCtd49439
link to view bug at Cisco.com
http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCtd49439
You need to contact TAC for the patch.Kindly click on Action --> open Service Request and it will put all these notes and logs of this thread to the TAC case.
Once the data collection issue will be fixed and the correct number of devices being data collected properly, then you need to make sure to add "Call Manager" to Common Services with the community string credentials and run the data collection and UT Acquisitions to get the IP Phones discovered.
Thanks,
Gaganjeet

LMS 3.2 CM, data collection stays running forever

Hi There
I have a customer who has LMS 3.2 Solaris. His CM, data collection, is in a running state for more than two days.
I am almost sure this is a bug, do you have any advice for me please.

see this thread:
https://supportforums.cisco.com/message/1322774#1322774
perhaps you are hitting BugId CSCtd49439
CSCtd49439 Bug Details
Data Collection never completes, and UT acquisition cannot run
Symptom:
Campus Manager Data Collection does not stop. It is reported as always
running in
Topology Services. Additionally, User Tracking acquisition does not run due
to XML files
being written.
Conditions:
This will occur if there are any standalone Access Points being managed by
Campus
Manager. Other devices can also cause this (e.g. old 1200 series switches).
Workaround:
Filter out standalone Access Points and other affected devices from Campus
Data Collection
under Campus Manager > Administration > Data Collection > Exclude Devices.
A patch is available by contacting TAC.

Problem Topology Data collection LMS 4.1

Hi there,
I have an issue with the lms 4.1 Topology Data Collection. In the Topo Data Collect under Inventory > Dashboards > Device Status > Collection Summary, there are only 2 devices succeeded and 0 device fail. but I have more 500 device in state managed. I run Inventory Collections but the number doesn't change.
Inventory Collection          534                13 02 May 2012, 11:07 CEST Idle          Schedule
Config Archive                         507               14 02 May 2012, 09:51 CEST Running          Schedule
Topology Data Collection               2               0 02 May 2012, 11:11 CEST Idle          Schedule
I have read others discussions but no one has the same problem or similar problem. The only possible solution is to reset the ANI db but I'm not sure if it it's the best solution.
Any ideas?
Thaks for help

I confirm that Martin. Good spotting!. I just noticed it in a server I installed yesterday. These 2 lines were added to the hosts file.
127.0.0.1       localhost
127.0.0.1   LMS4
A bit silly for both, since these entries were allready in the hosts file, done by the windows install I think
127.0.0.1       localhost
::1             localhost
Cheers,
Michel

LMS 4.2 Topology Data Collection Issue

Hi there,
i have an issue with the lms 4.2 Topology Data Collection. After installation the Topology Data Collection was running normaly, but since first server reload the Topo Data Collect under Inventory > Dashboards > Device Status > Collection Summary is "frozen". It only shows the following content from first run:
Topology Data Collection    193    0    Not Available     Running    Schedule
Is there any option to stop this process elsewhere? I cannot find anything under jobs in running state or so. Clicking on Schedule only give me the option to start data collection, but lms always returns that the process is running.
Thanks for help.

Hi,
i have reseted the ANI db using NMSROOT\bin\perl.exe NMSROOT\bin\dbRestoreOrig.pl dsn=ani dmprefix=ANI
Everything is set to 0:
Topology Data Collection      0 0 Not Available                          Running Schedule
UT Major Acquisition            0 (0 End hosts 0 IP Phones) 0      Not Available Idle Schedule
VRF Collection                    0 0                                              Not Available Idle Schedule
But Topology Data Collection is still frozen to "Running" state....

LMS 3.2 Data Collection Issue

Hi ,
I have LMS 3.2 and license for adding 5000 devices , my data collection is running continously for the past 2 days, when i try to stop the daemon manager and restart it comes to idle state but after some time it again goes to Running state
I am not getting the best practices deviations and discrepaqncies report after this issue
I am attaching the ANIServer.properties , ani.log and ANIServer.log file
Please help

this seems to be BugID CSCtd49439:
http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?caller=pluginredirector&method=fetchBugDetails&bugId=CSCtd49439
also consider to install the patch for BugID CSCtg20882:
http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?caller=pluginredirector&method=fetchBugDetails&bugId=CSCtg20882
if you have CM 5.2 you should consider to upgrade to CM 5.2.1 which is available here:
http://www.cisco.com/cisco/software/type.html?mdfid=282641773&flowid=5141&softwareid=280775108
the patches for BugIDs CSCtd49439 and CSCtg20882 are availabel by contacting TAC

LMS 3.2 Campuss Data Collection Does Not Start

I Discovered devices correctly in CS>DCR . Initially there was no problem in running data collection in Campuss Manager. But now when i try to run data collection manually or by a scedule, it does not start. Although the notification appears that "notified server to run data collection" but nothing happens then.
Also, I applied " net stop crmdmgtd" and then "net start crmdmgtd" and no error was reported. After this, data collection was successfully run, but just for once. That means, every time if i have to run data collection manually or by a schedule, i have to stop and start crmdmgtd ???
Please advise what to do.
Pleae note:
LMS 3.2 is installed on Windows Server 2003 service pack 2.

It looks like you are on Campus Manager 5.2. This should be fixed in 5.2.1. Proceed to upgrade to this version and then see if Data Collection runs fine. If you still have any problems, post the latest ani.log.

LMS 4.0 ANI Data Collection

Lately my ANI Data Collection seems to be running continuously. I even backed off the schedule for UT acquisitions to no avail. I also restarted the daemon manager.
I'm not sure if it's related but we made some changes on the management SVIs for a number of our switches to make them more reachable. I also upgraded to LMS 4.0.1
ANI Data Collection processes had been running fine earlier - kicking off on schedule and completing successfully.
I've attached a copy of the current ani.log

This looks like a new bug in LMS 4.0.1 introduced by the fix for CSCso03691. I don't yet have LMS 4.0.1 source and debugging is not enabled, so I cannot see exactly where the problem lies, but one of the port channel classes is not properly implementing the new methods for finding channels by ifIndex.

Data Collection Jobs fail to run

Hello,
I have installed three servers with SQL Server 2012 Standard Edition, which should be identically installed and configured.
Part of the installation was setting up Data Collection which worked with out problems on two of the servers, but not on the last where 5 of the SQL Server Agent Jobs fails.
The jobs failing are:
collection_set_1_noncached_collect_and_upload
Message:
Executed as user: NT Service\SQLSERVERAGENT. The step did not generate any output. Process Exit Code -1073741515. The step failed.
collection_set_2_collection
Step 1 message:
Executed as user: NT Service\SQLSERVERAGENT. The step did not generate any output. Process Exit Code -1073741515. The step failed.
collection_set_2_upload
Step 2 message:
Executed as user: NT Service\SQLSERVERAGENT. The step did not generate any output. Process Exit Code -1073741515. The step failed.
collection_set_3_collection
Step 1 message:
Executed as user: NT Service\SQLSERVERAGENT. The step did not generate any output. Process Exit Code -1073741515. The step failed.
collection_set_3_upload
Step 2 message:
Executed as user: NT Service\SQLSERVERAGENT. The step did not generate any output. Process Exit Code -1073741515. The step failed.
When I try to execute one of the jobs, I get the following event in the System Log:
- <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
- <System>
<Provider
Name="Application Popup"
Guid="{47BFA2B7-BD54-4FAC-B70B-29021084CA8F}" />
<EventID>26</EventID>
<Version>0</Version>
<Level>4</Level>
<Task>0</Task>
<Opcode>0</Opcode>
<Keywords>0x8000000000000000</Keywords>
<TimeCreated
SystemTime="2013-06-04T11:23:10.924129800Z" />
<EventRecordID>29716</EventRecordID>
<Correlation
/>
<Execution
ProcessID="396" ThreadID="1336" />
<Channel>System</Channel>
<Computer>myServer</Computer>
<Security
UserID="S-1-5-18" />
</System>
- <EventData>
<Data Name="Caption">DCEXEC.EXE - System Error</Data>
<Data Name="Message">The program can't start because SqlTDiagN.dll
is missing from your computer. Try reinstalling the program to fix this
problem.</Data>
</EventData>
</Event>
I have tried removing and reconfiguring the Data Collection two times using the stored procedure msdb.dbo.sp_syscollector_cleanup_collector and removing the underlying database.
Both times with the same result.
Below are the basic information about the setup of the server:
Does any one have any suggestions about what the problem could be and what the cure might be?
Best regards,
Michael Andy Poulsen

I tried running a repair on the SQL Server installation.
This solved the problem.
Only thing is that now I have to figure out the mening of these last lines in the log of the repair:
"The following warnings were encountered while configuring settings on your SQL Server. These resources / settings were missing or invalid so default values were used in recreating the missing resources. Please review to make sure they don’t require
further customization for your applications:
Service SID support has been enabled on the service.
Service SID support has been enabled on the service."
/Michael Andy Poulsen

Data Collection - values remained filled in from previous run through route

Hello,
We have an SFC that is running through a route the second time that requires specific Data Collection to be captured, but when Data Collection is attempted the values are all pre-filled in (and grayed out) from the previous run through the route.
The Data Collection needs to be entered in each time it is run through this route, especially if it is an RMA no matter how many times.
Am I missing a setting somewhere?
Thanks for your help,
Mike

Hello Sergiy,
The product goes through a normal route and is completed, SFC status = DONE.
The Product comes back and goes through an RMA route. First Operation data needs to be collected so it is entered by the Operator. The Product continues on and is completed, SFC status = DONE.
The Product comes back a second time and goes through the same RMA route. First Operation data needs to be collected, but it is already filled in with the data from the first time it went through the RMA route.
I was just wondering if I missed a configuration part or if this is a bug?
As always thanks,
Mike

ATP Item without Run Data Collection?

Hi,
Can we use ATP functionality (Not GOP) by defining ATP Rules in the system and attach it to the Inv. Org without running Data Collection Program?
I am new to ATP Functionality and planning to setup it in R12. All Gurus are requested to help me on this.

Please review Note: 420476.1 - Schedule Sales Orders Errors With The Requested Item Or One Of Its Components Is Not Collected
https://metalink2.oracle.com/metalink/plsql/ml2_documents.showDocument?p_database_id=NOT&p_id=420476.1

Planning data collection run

Hello!
I need to query the date/time of the last data collection run. Can anyone point me to the right table to get this information?
Cheers!

Look at LRD column in mrp_ap_apps_instances
Hope this helps,
Sandeep Gandhi

Data Collection 5.2 LMS 3.2 running always

Similar Messages

Maybe you are looking for