Data Corruption when installing Windows XP

Folks, I would greatly appreciate any direction you might have to help me solve te following issue.
Here are my parts:
k7n2 Delta - L
AMD XP 3000+
Saphire Radeon 9800 PRO 128
Antec Server case 430w Truepower supply.
Plextor 52/24/52 IDE
Maxtor SATA 80G + KINGWIN SAC-02 (Silicon Image SATA 3112 Controller)
OCZ Extreme performance Platinum PC3200 2x512 matched
I have no trouble posting and having the SATA drive come up as the boot device.
My issue lies in the transfer of data to/from the drive when trying to install the OS. I get inconsistent read/write errors throught the install and I can never get it passed the initial setup screen. It always BSOD's when it tries to load windows and finish the install. Obviously this is because a lot of the files were corrupted and/or not copied.
This is what I have tried.
I removed the SATA drive and installed a WD 40gig IDE drive : SAME ISSUE
I tried formatting all drives for FAT32 and NTFS : SAME ISSUE
I tried putting my working PC IDE drive in as boot drive and it just keeps rebooting itself right when it tries to load windows.
I tried removing sticks of ram: SAME ISSUE
I UPDATED the SATA card cmos to latest version as per the forums : SAME ISSUE
http://12.24.47.40/display/2/kb/article.asp?aid=10443I updates the MB Bios to latest version (5.7) as per the forums : SAME ISSUE
http://12.24.47.40/display/2/kb/article.asp?aid=10516
Any and all help is much appreciated
Blaszilla

Update: Settings were already set as you described. Same issue
All is well now, however. All the issues have gone away in one fell swoop.
Abit N7-S to the rescue. Booted on first try and stable as bedrock for 16 hours now.
That just says a whole lot in stark contrast to the k7n2 from MSI.
Just my humble experience. No flame intended. I am sure MSI has plenty of wonderful products, but k7n2 @ 400 is not one of them as is evident by a simple perusal of tech forums around the web.
Blas

Similar Messages

The keyboard and trackpad on MacBook Air (13-inch, Mid 2013) computers may stop functioning at the Personalize step when installing Windows 7 64bit

The keyboard and trackpad on MacBook Air (13-inch, Mid 2013) computers may stop functioning at the Personalize step when installing Windows 7 64bit.

1. Reset PRAM. http://support.apple.com/kb/PH4405
2. Reset SMC.     http://support.apple.com/kb/HT3964
    Choose the method for:
    "Resetting SMC on portables with a battery you should not remove on your own".
If this does not help, contact Apple.

Boot camp not recognize keyboard and mouse when installing windows 7 pro 64 bit

Hi,
I have some issue when installing windows 7 pro 64 bit using boot camp. after done partitioning the windows drive and when boot to windows installation process, i've got stuck in the first screen when choosing the language. it seems that the keyboard and mouse are not detected.
i'm using boot camp ver. 5.0.
does anyone have similar problem with me?

I have finally successfully installed Windows 7 x64 on MacBook Air 13.3" (2013) thru Bootcamp.
Problem: After Windows 7 install thru BootCamp, I got to the first login screen and not input devices (Mouse, keyboard, USB) worked. I tried to boot into Windows Safemode, but I received the error "Windows can not complete installation in Safe Mode".
Cause: WIndows 7 does not have native USB 3.0 drivers, included on the install images.
Resolution: I downloaded the latest device drivers with thru BootCamp and copied them to the USB Flash Drive that had my bootable Windows 7 x64 install on it. The second option in BootCamp is "Download Support Media". This does more than just download drivers. It creates a file called "autoattended.xml". This is key as it tells Windows during the install process to use the device drivers that you download. Otherwise, you need to do it manually, which you can't because you have no mouse or keyboard.
NOTE: I had no need of a super drive because I had all the files on one USB flash drive. Therefore, I don't think it matter which side of the MBA the USB drive was plugged in, as other solutions suggested.

HT4407 When installing Windows 7 using Bootcamp, I get message: "Need 64-bit Windows Installation USB drive or DVD." I thought my install disk was for 32 or 64 bit. What does this mean?

When Installing Windows 7 using Bootcamp, I get message: "Need 64 bit Windows installation USB drive or DVD." What does this mean?

It means you need the 64 bit Version of Windows on a USB stick or DVD.

Do I need to install boot camp on Windows 7 as well as on Lion? I already installed it some years ago on Leopard when installing Windows Vista on my Macbook Pro. But now after installing Windows 7, many things in windows doesn't work (sound etc.)

Do I need to install boot camp on Windows 7 as well as on Lion? I already installed it some years ago on Leopard when installing Windows Vista on my Macbook Pro. But now after installing Windows 7, many things in windows doesn't work (sound etc.). I made a clean installation because I needed to go from 32 bit to 64 bit.
Or should I just update bootcamp in Lion? (cause when I search for "boot camp" in Windows 7 there's no result)

Installation Guide
Instructions for all features and settings.
Boot Camp 4.0 FAQ Get answers to commonly asked Boot Camp questions.
Windows 7 FAQ Answers to commonly asked Windows 7 questions.
Apple Boot Camp Support
Lion's Boot Camp Assistant 4.x should have downloaded Apple drivers as part of also partitioning.
You need Apple drivers. And you then need to add on your own audio driver.
You can run Assistant at any time to download and save a set of drivers.

Error when installing windows 7

Hello... When installing Windows 7 Ultimate, I'm getting an error during the windows installation setup. I get the error 0x800024. I choose the correct partition, click install, and this error shows.
I'm on a mac pro and on snow leopard. I have boot camp 3.0.1, which doesn't show windows 7 when it's about to reboot into the installation screen. Is there anything I can do?

Have you looked here?
http://support.apple.com/kb/HT3986
Supposedly you need BootCamp 3.1 for Windows 7.
On a MacPro you can't have the Mac OS in slot 1 if you going to install Windows on a second drive. Just put the blank one in slot #1 (that you want Windows on) and then Mac OS drive in slot #2, #3 or #4 and it should work then.
Boot Camp can only use up to 2 partitions, Mac as #1 and/or Windows as #2. No 3rd partition. You have to have enough free space to use Boot Camp. If you have a 300 gig disk and you have 200 gigs worth of space used up it will only see the 100 gig of space left. And if it's an old disk you may not have enough CONTINUOUS space for it. The files may be all over and it can't find enough free space.
If on a second (blank) disk what I did was use Disk Utility to format/partition (UFS, Journaled) the whole disk as 1 partition and then let Boot Camp/Windows 7 (I used XP) repartition the disk as NTFS as the first partition (for XP) and left the second (for storage) alone. Or in your case just let Boot Camp/Windows partition it as one NTFS.
You have to tell it which one to use. If you don't have a choice then set the partition larger then 32 gigs then you should only have one choice, NTFS.
The Mac can't write to an NTFS disk so it can't make a NTFS partition. So that is why you just partition it like you would if you were only putting the Mac on it. (On an already blank disk). Then when Boot Camp/Windows takes over then Windows can write the NTFS partition.
The same with a Mac already on a hard drive. 1 partition. Boot Camp/Windows will then make the 2nd partition an NTFS partition (or what ever you want).
Hope this helps....

HP Deskjet Ink Advantage K209a Driver not found when installing windows 8

MY PRINTER " HP Deskjet Ink Advantage K209a" OPERATING SYSTEM Windows 8 32 bit
Driver not found when installing windows 8 .So,please give me a suggestion & give me new driver for win 8.
[Personal Information Removed]
Please give me a suggestion

Hey 101214,
I see you have a Windows 8 PC and a Deskjet Ink Advantage All-in-One printer (K209a). I also see that you need a driver link for this OS and Printer. Please follow the link below to download the driver for this printer/OS combo.
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=al-109242-1&cc=us&dlc=en&lc=en...
If you need information on how to perform the USB installation on your Windows 8 PC please click here.
I wish you the best!
Jason
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------
I am not an HP employee.

Cs12 trial not responding when installed, windows 7 64bit...how to fix??

cs12 trial not responding when installed, windows 7 64bit...how to fix??
Not a very good recommendation for buying the app!!!!
Does anyone at Adobe follow these questions??? If so please respond (your app will not!!)

Hi wcarlstrom,
Adobe CS12 is unheard of. Adobe Creative Suite's latest version is CS6.
Please be specific as to what software you are trying to install, OS version etc so that I may be able to help you.

Corrupt data error when using Windows backup on Oracle

Our SAP servers include a SDLT internal tape drive that we use for doing a complete system backup. When using Windows Backup we get the following message in the backup log:
WARNING: Portions of "\oracle\T00\sapdata1\protd_2\PROTD.DATA2" cannot be read. The backed up data is corrupt or incomplete.
This file will not restore correctly.
This is occuring on a couple of different systems but the wierd thing is when this happens in occurs on one Oracle drive in one system and the other Oracle drive on another system i.e. the G: drive on our TST sysytem and the E: drive on another. The E: and G: drives contain the main Oracle datafiles.
Has anybody ever encounter something like this and what can I do about it?
Thanks;
Gale S.

Especially no backup tool would know about the
fact
that a Oracle block had been changed after it was
copied.
Now I have to contracdict
There are backup tools (e. g. OpenFile Manager from
Legato/EMC), that track the filesystem changes and
makes sure, the backups are consistent in sense of
filesystem blocks. We´re backing up some ORA
databases (non-SAP, 7.3.4 and 8.1.7) for ages now -
and I never saw this kind of corruptions.
Well, these Backup-Tools do perform copies I/O-Consistent. That's different than DB-Block-consistent in the first place. Anyhow due to the fact that the DBMS do have a syncronizing between I/Os and writing out the blocks this leads both to consistent blocks.
I just wonder, how the database would deal with such
"inconsistent" files. Given the fact, you start a
backup at filesystem block 0, the database is being
backed up and a transaction is committed and
something is written to block 100, 200 and 500. The
backup is on block 300. If you now restore the
database, it has the already commited block 500 in
the file but 100 and 200 are not yet written in the
database file. The redo will then find an already
commited transaction on 500. What magic will tell the
engine, that this is due to an online database
backup? I mean, if you set the tablespace to backup,
the engine "knows" the state - but if you just backup
the file, the engine is unaware of that... I´m just
curious how this is handled...
Well the trick here is: we tell the database before we plan to copy the data. When a ONLINE backup is done, the tablespaces are set into BACKUP mode. This changes two things for us:
1. The datafile headers of these tablespaces are not updated anymore although dirty blocks are still written out to these files. Since the control files that keep the SCN (system change number) are updated nevertheless, the database will know at recovery time that these files had been in online backup mode and do need recovery to become consistent again.
2. The UNDO-information is not only written out to the UNDO/ROLLBACK-Tablespace but additionally to the REDOLOGS. So, for the time where the tablespaces are in BACKUP mode, we have all information needed to make a block consistent again - regardless if a transaction had been commited or rolled back - in the redolog. So a full recovery of all changes is possible with
that.
That's basically the "magic" behind this.
If the copy of the datafile is done without this - well, then there's no magician in the world that would been able to get it consistent again. Online Backups with Oracle are only possible with BACKUP mode or RMAN (ok, and possible some 3rd party hacks...).
KR Lars

Data error (cyclic redundancy check) when installing windows xp..

hi guys.. i'm new here.. just switched to macdom a few days ago but unfortunately, i have been having problems trying to install windows xp with sp 2 on my system using boot camp. everytime i install it, i get to the setup screen ("39 minutes till setup rah rah rah", "windows xp is awesome because it has this cool interface etc... rah rah rah") and then the error of doom comes out -_-
the error given is;
an eror has been encountered that prevents setup from continuing
one of the components that windows needs to continue setup could not be installed
data error (cyclic redundancy check)
if you are installing from a cd, there might be a problem with the disc; try cleaning the disc or using another disc
if you are installing from the network, it is possible that not all of the files were copied correctly to your disk drive. run the disk checking utility on your installation drive from the recovery console and start setup again
press ok to view the setup log file
i have tried numerous times without fail and it is getting to my head.. gah.. if someone could help me out, it would be massive and i would sell my soul to you! (kidding).. thanks for reading!
p/s: my setup is;
Macbook
2.1ghz
1gb ram
120gb hard disk
dvd/cd-rw combo drive
the basic setup pretty much.. again.. any help would be greatly appreciated. thank you so much guys!

I guess there is a problem with your XP CD, probably scratched or did not burn successfully. Have you tried it with another installation cd?

Issues when installing Windows XP on a PXI-8108 with a Solid State HDD

Hi,
I have been assisting a client with installing Windows XP onto a PXI-8108 controller. They have replaced the default HDD with a solid-state HD.
We have attempted to run the System Recovery CD. The recovery part works fine, ie. you select Acronis, it unzips all the files to C drive.
However when it gets up to the bit where Win XP Setup starts (after rebooting once the Recovery section completes), we have issues.
It can't find files, ie. dmconfig.dll, gm.dls, etc on the Win XP CD. When it tries to find mfc40u.dll, it came up with an error:
"The file Setup placed on your hard drive is not a valid Win XP System image. If you are installing from a CD, there may be a problem with the Windows XP CD."
We have tried two different recovery CDs, and we even tried just a plain Win XP CD. All had similar issues.
We have tried different SATA settings in the BIOS - both IDE AND AHCI.
It may just be that we have a faulty SSD, however it seemed to work ok when we had it connected to the PXI via USB (with the default HDD still in place). I was able to run diskcheck, which did not bring up any errors. Disk Management showed things were healthy.
So what I would like to know, is if there is any issue with a PXI-8108, and SSDs? We have successfully performed this operation a few months back using the same brand of SDD, but with a PXI-8104.
Any suggestions would be much appreciated!
Christopher Farmer
Certified LabVIEW Architect
Certified TestStand Developer
http://wiredinsoftware.com.au

This is more than likely a failing disk. SSDs don't always report failures in the same way as a rotating drive. Also, the tools that are helpful with diagnosing rotating drive failures don't always work with SSDs.
From the thread, it sounds like you have another system with this same SSD and it is working properly. Does that system have the same PXI Controller and Chassis?
I have seen these types of errors if the media for the OS installation is corrupt, but it sounds like you have tried different CDs.
I realize you have limited access to this drive, but here are my recommendations:
1) Put the failing SSD in a different system (desktop is preferable), and install a base version of XP. If this fails, RMA the drive, they normally have 3-5 warranties.
2) Run Crystal Mark Info and check for SMART failures:
http://crystalmark.info/software/CrystalDiskInfo/index-e.html
3) You can securely erase the SSD, which is not for the faint of heart. This will restore the drive to a new condition. If the drive has a bad cell which is causing data corruption during the OS install, securely erasing the drive will hopefully cause the firmware to map out the bad areas. This is a good tutorial, just ignore that fact that it is targeted at Intel drives.
http://www.iishacks.com/2009/06/30/how-to-secure-erase-reset-an-intel-solid-state-drive-ssd/
I hope this helps out,
Regards,
Andrew Mierau
Project Engineer - Servers & RAID Storage
National Instruments

Error 0x80070017 when installing Windows 7 via Boot Camp...

I've been trying hard to research this issue and haven't come across anything that has worked for me.
At work, we have an iMac (Early-2009) that we wish to install Windows 7 on. Previous user has left, so I reinstalled Snow Leopard (10.6) and used Disk Utility from the disc to reformat complete to GUID single partition Mac OS Extended (Journaled), which is pretty standard for Macs. Mac OS X installed and booted just fine. I updated completely to 10.6.8 and all other updates. Only installed Microsoft Office 2011 and Firefox.
So Boot Camp begins...
Found that the early-2009 model doesn't "support" Windows 7 64-bit, so we are fine going with 32-bit. The 32-bit Windows 7 disc has been used to install Windows 7 using Boot Camp on 2 Mac Mini's (one Intel Core Duo, the other one Intel Core 2 Duo) just a few days ago.
Opened Boot Camp Assistant, partitioned the 1TB drive equally, inserted the Windows 7 disc, and clicked Restart.
It boots from the Windows 7 disc, I go through the options, choose the BOOTCAMP partition and format it (I assume Windows 7 is choosing NTFS for me). Click next.
It copies the files instantly, but then "begins" to Expand the files. It remains at 0% for 5-10 minutes (I can hear the Windows 7 DVD spin down and spin up, but mostly spin down). That's when the error hits:
"Windows cannot copy files required for installation. The files may be corrupt or missing. Make sure all files required for installation are available, and restart the installation. Error code: 0x80070017"
I click Ok and cancel the install. Restart and boot back into Mac OS X. And here I am.
Important Notes:
I've tried multiple times with a 64-bit disc as well. I will likely go check out another 32-bit disc from our software department, but I know this disc works on other Macs.
This issue occurred a month back as well when we attempted to install Windows 7 via Boot Camp (so before the hard drive and OS were reformatted and reinstalled). I was hoping reformatting and reinstalling the Mac OS X would solve the issue.
The Superdrive appears to be working just fine.
I read somewhere that I need to use repair disk to fix it. Does anyone know if I can repair disk a NTFS partition? Or am I suppose to repair disk the parent drive itself? The place I read it wasn't specific AT ALL and the forum was closed and I couldn't find a way to get a hold of the person. It just said "Repair disk did the trick". People, if you find a solution to your own problem, POST the solution!
Thanks in advance!

Yea, I saw that kb article. I verified we have the early 2009 iMac. It's an iMac 9,1 (3.06 24-inch, A1225).
As far as different hardware, I really don't think so, but I'll have to double check with my fellow employees. The specs all match up, but I'll see if anyone remembers having to replace hardware or send it into Apple.
I did think of trying an external DVD drive too, I'll see if I can scrounge one up. I'll post if it works or not.
The employee using the machine knows Windows, but is willing to learn the Mac OS X. Diversify your experiences I always say!
An added note to the Repair Disk "solution". Turns out you can't run Repair Disk on NTFS partitions or the parent hard drive that contains that partition, which makes since. I can only run Repair Disk on the HFS+ partition which did no good. (This is, of course, from booting up using a Mac OS X Install DVD).
Mac_Win, thanks for the suggestions!

BSOD when installing Windows XP

I have two R500 ThinkPads that came with Vista Home Basic sp1. I need to install Windows XP Pro sp2 on the laptops but I keep getting a BSOD when I boot from the XP installation cd. The BSOD error is:
A problem has been detected and windows has been shut down to prevent damage to your computer.
If this is the first time you've seen this Stop error screen, restart your computer. If this screen appears again, follow these steps:
Check for viruses on your computer. Remove any newly installed hard drives or hard drive controllers. Check your hard drive to make sure it is properly configured and terminated. Run CHKDSK /F to check for hard drive corruption, and then restart your computer.
Technical information:
*** STOP: 0x0000007B (0xF7C04524, 0xC0000034, 0x00000000, 0x00000000)
The laptops are both brand new, I did make recovery disks of the vista install, but I really need XP installed on them to work with our system. Any help would be greatly appreciated.

There's a slightly easier way than slipstreaming.
The issue is that XP doesn't have driver support for the SATA AHCI controller on that system. However, you can download that driver here: http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-70477
You'll need to extract that and put it in the root of a floppy (yeah, a floppy... looking for the A: drive is hardcoded in to the XP install).
When you boot to the XP CD, press F6 when prompted (it'll say "Press F6 to install third-party SCSI controller" or something similar along the bottom).
Windows will load some files and eventually bring you to a screen with a couple of options. It'll tell you your current controller is "<none>" and allow you to press S to specify a driver. Once you do, it'll scan the A drive and load up the entries from the txtsetup.oem file you extracted from the driver.
The selection you want doesn't show up by default. There aren't any scroll bars, but you can scroll through the list using the arrow keys. You want "Intel(R) ICH9M-E/M SATA AHCI Controller" which is the 7th from the bottom.
Select that, Windows will load it, the install will continue and you'll be golden.
If you don't want to bother with scrolling, you can open the txtsetup.oem file and find this line (near the top):
[Defaults]
scsi = iaStor_ICH8MEICH9ME
Change that to:
[Defaults]
scsi = iaAHCI_ICH9MEM
And the proper controller will be highlighted by default so you don't have to arrow through the list.
If all of that is too much of a pain, you can go in to the BIOS under Config->SATA and change AHCI to Compatibility and load Windows w/o the IMSM driver. Once Windows is loaded, you can install the driver and enable AHCI mode using the install.cmd file in the PREPARE directory of the driver linked above.
Hope this helps.
Full disclosure: Lenovo issues my paychecks.

Blinking cursor when installing Windows 7 on a MacBook Air (Late 2010)

Hi.
After spending several days trying to solve this, I turn to this forum.
I have a MacBook Pro Retina (Mid 2012) and I had no problem installing W7 on that machine.
My wife has a MacBook Air (Late 2010), on which I am trying to do the same.
I use an external LaCie BD/DVD reader/writer, which I also used for the MBP without problems.
After partitioning and restarting, the install DVD doesn't seem to want to work with the MBA, though. Only a blinking cursor appears. Occationally some message like "Error code 5" or BOOTMGR image is corrupt. The system cannot boot."
I've tried starting with Alt, and when the screen appears where I can choose the Install DVD, there is no HD image, as on the MBP in the same situation, but just an image of a disk under which is written "EFI boot" - and it keeps poofing, appearing, poofing appearing. Actually, the first of these poofing images is actually called Windows, but choosing this returns the same blinking cursor.
I have tried resetting the PRAM and SMC, as well as repairing the disk.
Any ideas how to solve this?
Best,
Richard

leiladog wrote:
Can I install Window 7 Professional on a boot camp partition on my 1.8/2GB/64GB SSD MBA?
Today I installed Win7 Preimum on my brand new MBA (1.8/4GB/128GB SSD). I started with a stock MBA and first installed the new version of Parallels (7). After that installation, I installed Win7 Premium, followed by MS Office for Students and MS Streets and Trips. I should note that I also added slightly over 500 tunes for iTunes.
I was hoping to only install Excel and Word, but I never saw an option to go custom and as a result, all of Office for Students got installed.
With Parallels I didn't have to partition the hard drive. While I'm not totally sure, I think Parallels "grabs" empty space as needed, either for OS-X or Windows.
When I finished the installation, the computer reports that I still have 87GB.
I would assume if you went the route above and installed all the same programs, you would end up with 43GB of free space.
I intend to use my MBA as a road warrior, mainly surfing with some light Excel/Word. Unless you really need the Professional version, you might consider just installing the Premium version if the size of the program is much larger.
I've only been running for a few hours, but the machine seems very robust in both OS-X and Win7. Re the size of your hard drive, you might consider picking up a small external hard drive. I have a Western Digital Passport that is about the size of a cigarette pack and has the look of something that Apple might have made. 500GB for about $70.
I'm wondering if your 2GB of RAM might be a little on the weak side for going this route?

CRC missing file error when installing windows

When trying to instal windows on my Mac Pro desktop I keep getting the same error message. I must have tried it 6 times and always get the same message whether I am trying to my main disk partitioned, or to my secondary disk. It tells me to check my disk and I have, and cleaned it, plus I have ued the same disk to instal windows on my laptop Mac Pro without problems.
The message follows...
Error:
SXS.dll: syntax error in manifest or policy file "f:\i386\asms\6000\msft\windows\common\controls\controls.man" on line 4
xxx
error:
installation failed f:\i386\asms. Error message: Data error (cycle redundancy check)
xxx
fatal error:
one of the components that windows needs to continue setup could not be installed.
Data error (cycle redundancy check)
If you are installing from a CD there might be a problem with the disk; try cleaning the disk or using another disk.
Please help!
Doug

It should be "Cyclic Redundancy Check" I believe. If I were you I would check the disc for scratches...etc., and even if you can't detect any that are very visible, it would still be a good idea to go out and purchase some stuff designed for fixing scratches/blemishes on CD's so you can use them again. If that doesn't work, I'm at a loss.

Data Corruption when installing Windows XP

Similar Messages

Maybe you are looking for