DataIntegrator XI R2 couldn't get connection to SAP R/3

Specification:
- Data Integrator XI R2, SAP R/3 4.6C
Problem :
- I'm trying to connect data integrator R2 with SAP R/3 4.6c , and it doesn't work well unfortunately.
When I tried to connect DI with R3(QAS), it works well. but, when I tried to connect DI with R3(PRD), it doesn't work.
Looks like it doesn't work in case R/3 was composed of message servers.
In R3(QAS: Test System), there are only one AS(Application server).
In R3(PRD: Production System), there are 4 AS(Application server) and one of them has a role of messaging service(for Load balancing).
Any advices will help.
Best regards
Kyung woo.

Unfortunately BODI is not really sophisticated when it comes down to error reporting in connecting to SAP R/3. The generic error message can mean anything. I assume you got that error message and not a slightly more specific one referring to i.e. cannot access certain rfc functions etc.
I also assume that you could not connect to the SAP system, that the ABAP is not send or triggered and that you did not get back a job number.
You need to check:
SAP BODI account locked / invalid password
That you can reach the SAP server
That you logon to the right SAP logon group. DI lets then the R/3 system handle the load balancing between the application server. I think you can check this by filling in a target host in the SAP R/3 datastore so that DI goes to one application server. Assuming your SAP system does allow this.

Similar Messages

Get connection with SAP

Hi
How is it possible to get connection with SAP system when i am working in SAP NetWeaver developer studio?
do i required any connector for this?
Regards

Hi Quali,
Inorder to get connected to the SAP system via your SAP NWDS(SAP NetWeaver developer studio).
1) Please check if you are able to get connected to the remote server, incase the server is on a different machine. You can do it by following the steps below:
Click on Windows Start menu -> click on Run -> Typein "cmd" and click on Ok button -> Typein "Ping 'IP address of the remote server'", I mean your remote server machine's IP address(Ex:10.6.52.189 or whatever it is). If it responds then please carry out the following steps in NWDS.
2) Please GoTo :
NWDS menu - > Window -> Preferences -> SAP J2EE Engine(Choose this on the left menu).
Now, if your server is not installed on the same machine on which you are working then go for the first radio button which says "SAP J2EE engine is installed on remote host" and enter the server's IP(Internet Protocol) address(Ex: 10.6.52.14, etc)in "Message Server Host" and enter 3601 in "Message Server Port".
Click on apply and Ok.
3) Now again Click on Windows Start menu -> click on Run -> Typein "drivers" and click on Ok button -> Open the folder "etc" -> look for file "Hosts", openwith notepad
-> Now typein the IP address and the corresponding host name(of the remote server)please note that the IP address and the host name should be separated by at least one space, preferably a tab space. -> save the hosts file.
Now you should be able to connect to your remote server.
Regards,
Sudeep

Could not get connections for 2 databases at the same time

Hi, I have a session bean which calls 2 entity beans in one method. The 2 entity
beans are located in different databases (different datasources and different
pools). When running, I got the following error:
Couldn't get connection:
java.sql.SQLException: Connection has already been created in this tx context
for pool named iitga_jdbc. Illegal attempt to create connection from another pool:
iitdbmap_jdbc
It seems WebLogic only allows one database connection within one method.
Thanks,

Hi Henry,
If you want two beans bound to different database, you need
to use XA pools with TXDataSources because in this case you
have a distributed transaction.
Set up you pools using XA drivers and make sure you use
TXDatasources.
If you tell us which database you use we may come up with
sample pool configurations.
"Henry Hiu" <[email protected]> wrote in message
news:[email protected]..
>
Hi, I have a session bean which calls 2 entity beans in one method. The 2entity
beans are located in different databases (different datasources anddifferent
pools). When running, I got the following error:
Couldn't get connection:
java.sql.SQLException: Connection has already been created in this txcontext
for pool named iitga_jdbc. Illegal attempt to create connection fromanother pool:
iitdbmap_jdbcRegards,
Slava imeshev

When I got my ipod I made an account with iTunes from my ipod.yesterday, I made a password lock to get into my ipod and I couldn't get into it even though I did the correct one. Now it says"connect to iTunes" BUT I can't because I never registered. HELP!!

When I got my ipod I made an account with iTunes right from my ipod.Yesterday, I made a password lock to get into my ipod and I couldn't get into it even though I did the correct one. Now it says"connect to iTunes" BUT I can't because I never registered on the computer. I've tried holding the home and sleep/wake button for 10 sec and then only the home for 5sec and that might have reset it, but it didn't help. If any of you guys know what to do so I can unlock it I would appreciate it VERY much.

If you haven't done so install iTunes on your computer. http://www.apple.com/itunes/
Follow the instructions here: iPhone and iPod touch: Unable to update or restore

I have reset my iPod because it had been locked out and I couldn't get back in, but it will only reset once it connects to a WiFi source. I cannot get onto my iPod to connect it to a WiFi source. How am I meant to reset/erase it?

I have reset my iPod because it had been locked out and I couldn't get back in, but it will only reset once it connects to a WiFi source. I cannot get onto my iPod to connect it to a WiFi source. How am I meant to reset/erase it?

Just what do you mean by " but it will only reset once it connects to a WiFi source."?
If it it says turn off FIndMyiPhone then:
Place the iOS device in Recovery Mode and then connect to your computer and restore via iTunes. The iPod will be erased.
iOS: Wrong passcode results in red disabled screen
If recovery mode does not work try DFU mode.
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
For how to restore:
iTunes: Restoring iOS software

DO NOT DISTURB was in effect. I couldn't get wi-fi connection until I turned DND off. Is that a bug or to be expected?

I just started using DO NOT DISTURB at night but needed to send out an email. Was surprised that wi-fi had shut off. Couldn't re-connect until I turned DND off. Then wi-fi connected immediately. I hope this was just a temporary glitch.

Resolution
If you encounter this issue, try the following steps and attempt to enable Wi-Fi or Bluetooth after each one.
Verify that Airplane Mode is turned off.
Update your iOS device to the latest version of iOS.
Reset Network Settings. To do this, tap Settings > General > Reset > Reset Network Settings
Restore your iOS device in iTunes.
If you are still unable to turn Wi-Fi or Bluetooth on or off after attempting these steps, contact Apple or your wireless carrier for additional assistance.

[solved] couldn't get NX work after switching to 64 bit system

I switched the system to 64 bit with my "home" folder untouched. Then I couldn't get NX work. Here is the detailed output:
NX> 203 NXSSH running with pid: 4866
NX> 285 Enabling check on switch command
NX> 285 Enabling skip of SSH config files
NX> 285 Setting the preferred NX options
NX> 200 Connected to address: xxx.xx.xxx.xxx on port: 22
NX> 202 Authenticating user: nx
NX> 208 Using auth method: publickey
HELLO NXSERVER - Version 3.2.0-73 OS (GPL, using backend: 3.4.0)
NX> 105 hello NXCLIENT - Version 3.2.0
NX> 134 Accepted protocol: 3.2.0
NX> 105 SET SHELL_MODE SHELL
NX> 105 SET AUTH_MODE PASSWORD
NX> 105 login
NX> 101 User: horse
NX> 102 Password:
NX> 103 Welcome to: office user: horse
NX> 105 listsession --user="horse" --status="suspended,running" --geometry="1400x1050x24+render" --type="unix-gnome"
NX> 127 Sessions list of user 'horse' for reconnect:
Display Type Session ID Options Depth Screen Status Session Name
NX> 148 Server capacity: not reached for user: horse
NX> 105 startsession --link="wan" --backingstore="1" --encryption="1" --cache="16M" --images="64M" --shmem="1" --shpix="1" --strict="0" --composite="1" --media="0" --session="work" --type="unix-gnome" --geometry="1400x1030" --client="linux" --keyboard="pc102/us" --screeninfo="1400x1030x24+render"
NX> 1000 NXNODE - Version 3.2.0-73 OS (GPL, using backend: 3.4.0)
NX> 700 Session id: office-1000-593D8F5A1C9C4FC7C01CA605A678F07D
NX> 705 Session display: 1000
NX> 703 Session type: unix-gnome
NX> 701 Proxy cookie: b3fb6908954b810ed8535b0deb2ff786
NX> 702 Proxy IP: 127.0.0.1
NX> 706 Agent cookie: b3fb6908954b810ed8535b0deb2ff786
NX> 704 Session cache: unix-gnome
NX> 707 SSL tunneling: 1
/opt/NX/bin/nxagent: error while loading shared libraries: libXcomp.so.3: cannot open shared object file: No such file or directory
/opt/NX/bin/nxserver: line 1531: 8001 Terminated sleep $AGENT_STARTUP_TIMEOUT
NX> 105 NX> 596 Session startup failed.
NX> 1004 Error: NX Agent exited with exit status 1. To troubleshoot set SESSION_LOG_CLEAN=0 in node.conf and investigate "/home/horse/.nx/F-C-office-1000-593D8F5A1C9C4FC7C01CA605A678F07D/session". You might also want to try: ssh -X myserver; /opt/NX/bin/nxnode --agent to test the basic functionality. Session log follows:
Can't open /opt/NX/var/db/running/sessionId{593D8F5A1C9C4FC7C01CA605A678F07D}: No such file or directory.
mv: cannot stat `/opt/NX/var/db/running/sessionId{593D8F5A1C9C4FC7C01CA605A678F07D}': No such file or directory
NX> 1006 Session status: closed
NX> 280 Exiting on signal: 15
I guess there are two problems with it:
1. It couldn't resume. (in fact I want to start a new session. I don't know where are the old session information: I already removed all related file in the home folder.)
2. the error with "nxagent". It says it couldn't load libXcomp.so.3. I don't know how to install it.
Any help will be appreciated.. Thanks!
Last edited by horsecool (2010-12-28 17:53:36)

Thanks for your reply! I do have Xorg installed. And The X works fine on the local computer (not remote login).
Here is the result from "locate libXcomp":
$ locate libXcomp
/opt/NX/lib/libXcompext.so
/opt/NX/lib/libXcompext.so.1
/opt/NX/lib/libXcompext.so.3
/opt/NX/lib/libXcompext.so.3.4.0
/opt/NX/lib/libXcompsh.so
/opt/NX/lib/libXcompsh.so.3
/opt/NX/lib/libXcompsh.so.3.4.0
/opt/NX/lib/libXcompshad.so
/opt/NX/lib/libXcompshad.so.3
/opt/NX/lib/libXcompshad.so.3.4.0
/usr/lib/libXcomposite.so
/usr/lib/libXcomposite.so.1
/usr/lib/libXcomposite.so.1.0.0

Couldn't get personal hotspot to work

I tried the personal hotspot tonight for the first time (it is supported on my carrier - AU in Japan) but I couldn't get it to work.
The restaurant I was in had wifi that my iPhone automatically connected to. I think that was one issue. For the personal hotspot to work, doe the iPhone need to be connected to the Internet over LTE or 3G?
My personal computer could not connect to that same restaurant wifi because it was a member's only wifi for AU cell phone users.
If I turned off wifi to force my iPhone to be connected via LTE but then I got a message saying wifi needed to be turned on to use the personal hotspot feature.
So I turned wifi on again, but my iPhone's wifi did not appear in the personal computer's list of networks to connect to.
Anyway... how would one get this to work? I think I wanted my iPhone connected via LTE, wifi on but NOT connecting to that AU wifi. Is that right? I didn't see how to get the iPhone to NOT connect to the wifi if wifi was on.
Thanks,
doug

The problem was that the network settings needed to be reset. After that it worked properly which is like this:
When I entered the restaurant (or at home) the iPhone 5 connected to the known wifi network. That's fine.
When I turn on personal hotspot, the wifi mark disappears and you see the carrier name and connectivity in its place. In my case it said "KDDI LTE".
At this time the wifi network name appears just fine in the personal computer's list of hotspots and you can select it, enter the password and connect.
When you turn off the hotspot, if you were connected to wifi then the wifi mark re-appears.
Anyway, I just tried it from home. I did a speedtest on my iMac tethered by wifi to my iPhone 5's personal hotspot. Not too bad - download 7.23 Mbps and upload 6.70 Mbps.
doug

After update of Yosemite, Finder couldn´t get access...

After update of Yosemite, Finder couldn´t get access to Time Capsule. Connection failed. Restart of the Time Capsule doesn´t solve the problem.

The trick seems to be:
unmount volume (eject whatever)
turn wifi off
turn wifi on
Cmd-K (or whatever) to find and remount volume.
This is with Yosemite 10.10.1 update.

Broadband light blue, can get connection between d...

ADDED ADSL SETTINGS TO END OF THIS EMAIL
Please Help - getting desperate !!!
I have a BT Home Hub 3 and use wireless connectivity to communicate to the following devices -
MacBook Pro
Windows Laptop (used rarely)
iPad
Wireless printer
I intermittently experience a problem where, although my broadband light on the Home Hub was blue and I could get connection from my laptop/ipad to the Home Hub (i.e. on the MAC I can see the BT Home Hub on my Airport indicator and its a bona-fidae connection), there was no internet connectivity. This was an intermittent problem - some days I could surf fine, other days I couldn't get any internet connectivity. Also it is device agnostic - i.e. when the problem occurs it effects all my devices, when it is not evident all my devices work.
I went through the customer support helpline in september and the intermittent problem could not be solved. An engineer came out and replaced my Home Hub in September and things seemed to improve until December when the problem re-occurred and I was sent another new home Hub 3. This didn't solve the issue and at present I would say that 2 to 3 days a week I (randomly) get no internet connectivity.
Throughout the course of investigations several things have been tried with the customer support folks - these include -
Line checks - these confirmed broadband connectivity to the house was mostly fine
frequent resetting of the Home Hub
re-configuration of the Home Hub <-> device channel number. This was done several times and with different 'departments' in BT Support - e.g. once I got connected through to the 'MAC OS' folks who recommended use of channels 5,7 for Macs.
repositioning my devices to make them closer to the Home Hub (no difference as the home hub is very close to where I work in the house anyway)
switching on/off my Plasma TV!! (no difference)
on occasion these things have brought internet connectivity back on-line, but the intermittent problem invariably comes back.
This has become a real pain and its becoming impossible to do any planned work from my home office - any assistance greatly appreciated
ADSL SETTINGS AT the moment ---
ADSL Line Status
Connection Information
Line state:
Connected
Connection time:
0 days, 01:10:50
Downstream:
7.813 Mbps
Upstream:
448 Kbps
ADSL Settings
VPI/VCI:
0/38
Type:
PPPoA
Modulation:
G.992.1 Annex A
Latency type:
Interleaved
Noise margin (Down/Up):
6.4 dB / 29.0 dB
Line attenuation (Down/Up):
35.0 dB / 19.0 dB
Output power (Down/Up):
19.9 dBm / 12.7 dBm
FEC Events (Down/Up):
38825 / 0
CRC Events (Down/Up):
3 / 1

liammcquillan33 wrote:
Hi -
not sure why you have moved this into 'Wireless' - I'm not sure its a wireless problem. Can you move it back
You said
"I have a BT Home Hub 3 and use wireless connectivity to communicate to the following devices -"
There is nothing wrong with your ADSL connection statistics.
Try connecting to the home hub using an Ethernet cable to your computer.
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

Two beeps when an incoming call gets connected

Since a couple of weeks ago I started hearing 2 beeps when an incoming call gets connected.
I can only hear these 2 beeps when I use my headset (original iphone headset) to answer the call. I hear these 2 sounds right after I answer the call and then I can hear the person on the other side of the line.
This does not happen for outgoing calls. The person on the other side of the line can't hear the beeps. I tried this in another iPhone and I couldn't hear the beeps either.
Does anybody knows why?
Please, serious answers (I'm tired of listening about the bighbrother thing)

Hi there,
Did you ever figure out what those beeps are? I'm hearing them too.
Thanks!

E4200- Just couldn't get it to work

So I purchased this product a few weeks for a great price. I knew there was some concern about the router. However, I took a chance and bought it. It was a breeze to set up everything. Yet it didn't take long before I ran into issues. First, let me explain my setup. The router is integral to my overall network. It is tied to client bridge. Also, the Samsung tv, Samsung Blu-ray, Denon receiver, Xbox 360 are also connected through D-Link switch. In addition, there are number wireless devices that get access such as , iphones, laptops, etc. I noticed that I couldn't get the xbox to properly connect to multiplayer matches. Also, facetime lost its connections after a few minutes. I tried to troubleshoot the latency with our cable operator and we zeroed on the router. I found out that the device works for a few minutes after your reset it but it didn't take long before it got flaky again. Subsequently, I ended up returning the device and getting a Airport extreme (not my first choice). However, I must admit that the extreme has been rock solid.

As you mentioned that your Xbox was connected through the D-Link switch which was connected with the Cisco Router E4200 and you were facing the problem of getting properly connect to multiplayer matches... But did you try to connect the Xbox directly to the Router E4200 and checked whether you were getting the same concern? If yes then here is the link which can help you:
http://www6.nohold.net/Cisco2/ukp.aspx?pid=93&login=1&vw=1&app=search&articleid=23787&userrole=Links...
Secondly if you were facing the concern with connection then you would have done the following steps but before that let me know how you did install the Router – means was configured with the help of the Cisco Connect Software or did manual configuration?
If you did configure the Router with the help of the Cisco Connect Software then would have opened that up in which you had installed… There you could able to see 4 small window screens…You would have clicked on “Router setting” window…Then clicked on “Advanced settings” button… That would have opened the Router Setup page, clicked on Wireless Tab and made the following wireless channel-
For Channel Settings of 2.4 GHz ---> Channel Width to 20 MHz only and Channel to 6, 9, 11..
For Channel Settings of 5 GHz --->Channel Width to 20 MHz only and Channel to 40 or 161...
Then would have checked the connectivity…
If you did configure the Router manually then would have opened up the browser and on the address bar would have typed 192.168.1.1 that would have opened the Router setup page… From there you would have done the same steps as above…

Why Apple Mini-DVI to DVI Adapter couldn't be connected?

i purchased Apple Mini-DVI To DVI adapter but it couldn't be connected to any port of my macbookpro 13" without retina
if you 've solution please advise.

What is the model identifier of your MBP? Also what oSX are you using?
You can find this info by clicking on the Apple in the menu bar About this Mac, in the first window it should should show the OSX Version.
Then click on More info, and the next page (Hardware overview) second line should be Model Identifier: x,x
What are you connecting to and what type of input(s) does it have. If you do not know how to idendify the inputs, post the make, model of the device.

Weblogic realm authentication failure getting connection from pool

We are getting this error when we try to get a connection from the
pool for a Tx Data Source. We are successfully getting connections
from a (non-Tx) Data Source.
java.lang.SecurityException: Authentication for user Fitness_demo
denied in realm weblogic
at weblogic.security.acl.Realm.authenticate(Realm.java:212)
at weblogic.security.acl.Realm.getAuthenticatedName(Realm.java:233)
at weblogic.security.acl.internal.Security.authenticate(Security.java:125)
at weblogic.security.acl.Security.doAsPrivileged(Security.java:481)
at weblogic.jdbc.common.internal.RmiDataSource.getConnection(RmiDataSource.java:127)
We have added the DB user as a user in the realm, which usually does
the trick; but in this case it does not. We are using Merant's
JSQLConnect type 2 driver for SQL Server, and we are running on
Solaris. The scenario works fine using Oracle Thin driver on Windows.
Do we need ACL entries or something? We do not have any ACL entries
now.
Thanks,
-wes

We are getting this error when we try to get a connection from the
pool for a Tx Data Source. We are successfully getting connections
from a (non-Tx) Data Source.
java.lang.SecurityException: Authentication for user Fitness_demo
denied in realm weblogic
at weblogic.security.acl.Realm.authenticate(Realm.java:212)
at weblogic.security.acl.Realm.getAuthenticatedName(Realm.java:233)
at weblogic.security.acl.internal.Security.authenticate(Security.java:125)
at weblogic.security.acl.Security.doAsPrivileged(Security.java:481)
at weblogic.jdbc.common.internal.RmiDataSource.getConnection(RmiDataSource.java:127)
We have added the DB user as a user in the realm, which usually does
the trick; but in this case it does not. We are using Merant's
JSQLConnect type 2 driver for SQL Server, and we are running on
Solaris. The scenario works fine using Oracle Thin driver on Windows.
Do we need ACL entries or something? We do not have any ACL entries
now.
Thanks,
-wes

Powerpivot Error on Refresh -- "We couldn't get data from the data model..."

I'm using Excel 2013 and Windows 8.1. I have a spreadsheet I've been using for over a year, and I've just started getting this error message when I try to refresh the data.
"We couldn't get data from the Data Model. Here's the error message we got:
The 'attributeRelationship' with 'AttributeID' - 'PuttDistCat9' doesn't exist in the collection"
Any idea how I can fix this problem? I haven't changed anything related to that particular attribute. All the data is contained in separate sheets in the workbook, so there are no external sources of data.
Thanks.
Jean

Thanks for all the suggestions.
I found a slightly older version of the spreadsheet that still refreshes properly, so I don't think I have any issues with the version of Excel or Power Query. (I've had this same error before, and I believe I applied the hotfix at that time.)
I think this problem started after I updated a number of the date filters in the pivot tables. I haven't made any changes to the data model, and the only updates I've made were to add data (which I do all the time), and to change the date filters on
the pivot tables.
As suggested, I added a new pivot table querying one table (the table with the attribute that shows up in the error message), and it worked fine. I can also refresh this pivot table.
Then I tried adding a pivot table which went against several tables in the data model (including the table in question). The pivot table seemed to return that data properly. However, when I tried to refresh it, I got the same error message ("we
couldn't get data from the data model...").
Dany also suggested running the queries one at a time to see which one is in error. Without checking all the pivot tables, it appears that any which use the table "HolePlayedStrokes" generate the error (this is the table with the attribute
mentioned in the error message). Pivot Tables without that particular table seem to refresh OK. Unfortunately, that is the main table in my data model, so most of the pivot tables use it.
Any other suggestions? I'd be happy to send a copy of the spreadsheet.
Thanks for all the help.
Jean

DataIntegrator XI R2 couldn't get connection to SAP R/3

Similar Messages

Maybe you are looking for