DC WAE Design help

Attached is a visio of main DC WAN edge. Right now our WAE (7341) is placed directly off of ncmc-dc-rt01. Now we need to start to optimize traffice comming from all three top routers (ncmc-dc-rt01, ncmc-dc-rt05, and ncmc-dc-rt04). Were would be the best placement and IP address shceme for the WAE? Keep in mind the ncmc-dc-rt05 is a 3750g.

James,
I might consider putting the WAEs off the aggregation switches and doing hardware redirection (L2 redirect, mask assign, redirect in) on the 4900s. Otherwise you won't be able to use all three WAN routers as on will require L2 redirects and the other only support GRE.
Hope that helps,
Dan

Similar Messages

  • Unable to toggle between LiveCycle Designer & Help

    If we opened the LiveCycle Designer Help window, we are unable to switch to the Designer util the help window is minimized. This is slightly annoying the developers.
    It would be better if it can behave like other applications (e.g. Adobe Workbench ES)
    Thanks,
    Nith

    Charlie
    I am unable to duplicate the problem you are experiencing.  I was able to use Acrobat Pro 9 and X, to apply the Reader Extension permissions (to the sample form I posted earlier) and open and sign the form in both Reader 9 and X.
    What is the exact version of Acrobat you are using to apply the Reader Extension rights.  The dialog I see when doing so with Acrobat 9 Pro is...
    If you are using Acrobat Standard, it seems there is a limitation (save data only) on the Reader Extension permissions that you can apply.
    Regards
    Steve

  • I like to pdf my score. I design my score properly, but then when I make the PDF it changes, in not correct design, help!

    i like to pdf my score. I design my score properly, but then when I make the PDF it changes, in not correct design, help!
    the same problem when normal printing

    You have 90 days of free AppleCare telephone support, please call them. If you don't know the number please click AppleCare Contact Info to locate the number on your part of the planet.

  • Trade-off between the one-arm and two-arm WAE designs

    We are configuring a WAE (model 512) for a branch office and I was wondering if someone could please tell me the trade-off between the one-arm and two-arm WAE designs..
    thanks..
    greg..

    if you are using WCCP then the WAE becomes the client withing the servcie groups 61, 62. In order to accelerate both vlans then apply the ip redirect 61 in on the client vlan ineterfaces to the one interface.
    If inline, you can use both 2 port groups for each client interface or trunk all to a single inetrface and configure which vlans you would like to accelerate.
    Now in terms of of using both GE inetrfaces, I would have to check. A topology diagram would help

  • Non-profit needs Dreamweaver design help

    Small non-profit serving homeless veterans and veterans in crisis needs design help with Dreamweaver website.  The website was created as a school project by university students but there are some design issues that we are not able to correct.

    It appears to be template driven so the basic layout is inside your site folder's Templates directory -- main.dwt.   This file drives the site wide elements such as navigation, common headers, footers and sidebars. 
    Child pages created from that main.dwt file contain editable regions for content that will change from page to page.  Only content in these editable regions are editable from child pages.
    Whoever will be responsible for updating content should get familiar with CSS & HTML code.  This is required knowledge to work with Dreamweaver.
    Start here:
    HTML & CSS Tutorials - http://w3schools.com/
    Code validation tools
    http://jigsaw.w3.org/css-validator/
    http://validator.w3.org/
    Also thoroughly read DW's Help docs (F1) under working with DW Templates. 
    It looks like the students did a pretty fair job of building the basic site for you.  Now it's up to your org to swap out the generic stuff with relevant content.   I don't advise you to alter the basic layout or structure.  It's all there.  You just need to get up to speed on how to work with it.
    Nancy O.

  • Need some design help

    Well "overall" design help. This project MUST be open source so it does ensure i am very efficent in my design
    Basically my system is going to be a bunch of work stations that tunnel into a server to send the data.
    Now the big issue is, each work station must encrypt its own data and save it on its HD, but it must send data to the server for the server to save it and encrypt it (redundency).
    The big issue is sending data to the server. the keys, how do i securely send them to the server so they can decrypt the stream? everything will randomly generate its key whenever the user (or the system) decides it is time to for the sake of not resuing keys.
    basically we are going to use linux, lock down all ports but one to use sockets to communicate with the server (and vice versa). this adds an extra layer just so we can authenticate with the server machine (and client machines when the server sends it a request)
    help? more info needed?

    I know (next to) nothing about system security (well,
    not enough to be advising people, anyway) - but the
    key distribution problem is typically solved by using
    Public Key Cryptography to exchange a Session Key.
    Have you thought about using an existing system like
    SSL or Kerberos?eh SSL won't really work... i a mgoing to pick up "Cryptography Decrypted" apparently it is a good book to pick up some of the things i need

  • Design help to the forms

    Hi gayes
    I need your help in designing help to any any working screen such that when the user push F1 buttons , click the right buttons of the mouse and choose help from the popmenu,or choose help from the menu bar . It must give him the correct help.
    Also this "help screen" how could I make it,and connect it to the help of windows98 to work.
    Thanks

    Hi Kimberg Howe,
    You have several alternatives to generate a .hlp file. You can do it manually in words and save the file as a rich-text-format (.rtf), and then use the Microsoft Help Workshop (a Free Program obtainable from www.microsoft.com site) but realize that you will have to code all the Winhelp engine commands and that's some task. However, you can investin some WYSWYG winhelp file generators. I guess it is not appropriate to suggest any in this forum, but you can do a search on any search engine for keyword "Winhelp", or you can also search on www.download.com
    What this program will do for you is to allow you design your help file and then generate the .hlp for you, some of these programs can also allow you to generate html files that is suitable for web forms.
    I hope this help.

  • Design Help / Education

    Does anyone know if Adobe offers any design education
    I need some basic design help using Dreamweaver (as I am
    having issues migrating from Go Live)
    If not Adobe, are there any experienced DW users out there?
    thanks

    Experienced DW users? Well, yeah.
    What do you need?
    Murray --- ICQ 71997575
    Adobe Community Expert
    (If you *MUST* email me, don't LAUGH when you do so!)
    ==================
    http://www.projectseven.com/go
    - DW FAQs, Tutorials & Resources
    http://www.dwfaq.com - DW FAQs,
    Tutorials & Resources
    ==================
    "golfingdad" <[email protected]> wrote in
    message
    news:gefblj$2pt$[email protected]..
    > Does anyone know if Adobe offers any design education
    >
    > I need some basic design help using Dreamweaver (as I am
    having issues
    > migrating from Go Live)
    >
    > If not Adobe, are there any experienced DW users out
    there?
    >
    > thanks
    >

  • Design Help! Add new lines

    Hi All,
    I need a design help for adding extra lines on an existing order.
    I have a page with 2 subtabs, first one is for order header info inputs and second one is for line info inputs. The line subtab base on user selection may generate mutile lines in lineVO (multiple rows). After user clicked an apply button on line subtab, a header row will be committed into header table and line row(s) will be in line table.
    I was trying to have another button to allow user enter extra lines after committed existing header and line VO. After user click the "add extra line" button, I retain AM to keep header VO but flush out line VO, with this way, framework will try to delete lines in line table.
    Since there are lots logic requirements, I can't keep adding lines after line VO.last() without committing first round line entering.
    How can I keep Header VO, clean line VO, then enter new line(s) info as ADD but not DELETE/UPDATE? any suggestion??
    Thanks & Regards,
    KJ

    Hi Shreya,
    I am not sure about giving new line in each and every page, but there is an alternate. You can show all data in one single page. That is how much ever records you have, they will be shown on one single page, instead of spanning across multiple pages. You can achieve this by changing the property "Number of Data rows displayed at once" from default 100 to 0.
    Hope it helps.
    Regards,
    Arunan.C

  • WAAS Design Help Needed - URGENT!

    Hi,
    I am currently designing and implementing a WAAS solution for s client in their Data Center. It is deployment of a single Accelerator and one CM.
    It has been decided that the WAAS accelerator (7341) will have its two NICs connected to two of their core switches (both 6500). The two core switches have a Layer 3 Etherchannel link between them and are running OSPF for network convergence (i.e. Layer 2 connectivity is not used).
    I am facing a problem in the design, since I know that the Active/Standby configuration for the accelerator would require a redundant gateway via HSRP (at least) but this is not possible in a routed environment in the core switches. Furthermore, I am to run WCCPv2 for redirection.
    Therefore, I am confused as to how to proceed in such a case considering that I can only configure one default gateway on the accelerator when I need high availability on two different subnets.
    Please assist at your earliest.
    Thanks.

    Amir,
       Considering your question below
    "I am facing a problem in the design, since I know that the Active/Standby configuration for the accelerator would require a redundant gateway via HSRP (at least) but this is not possible in a routed environment in the core switches. Furthermore, I am to run WCCPv2 for redirection."
    Do WAE is configured for Standby interface and is this your Primary Interface as well? If answer is yes then see below
    You will need a common VLAN for WAAS on both 65K swicthes in order for Active / Standby interface to work properly.
    1: When using OSPF make sure your tcp flows has both ingress and egress flows transit from same switch
    2: Use Generic GRE method for Egress under WAAS intercept configuration.
    Since you are running WCCP each swicth will be able to redirect its TCP traffic via GRE Tunnel to WAAS and WAAS will send the packet back to the same swicth. This will ensure packet path is not modified when WAAS / WCCP is introduced.
    Also make sure that you do not have any WCCP redirect on Layer 3 connection between 2 swicthes. Let me know if this helps.
    Ahsan Khan

  • Roaming and 2.4 vs 5.0 on 1250 series AP design help

    Hello,
    I will be upfront and honest and state that although I am familiar with some wireless technologies, most of this stuff is a mystery to me. I have done some homework and have researched quite a bit, but have ind of hit a wall.
    I have been handed four Aironet 1250 series AP's all with the dual radio modules (2.4 and 5.0). I really need to use only one of the modules so that we can power it via POE and not enchanced POE (long story).
    So, I need help with a design. Here's what I'd like to see.
    1.       I would like to setup "roaming" so that when a wireless client goes from one AP to another it is seamless to the user and the users NIC will associate with the strongest AP signal. Can I do this by simply setting the same SSID and security on each AP, or must I have a controller to do this?
    2.       Also, I cannot seem to get older legacy clients to communicate with the 5.0 Ghz radio module (they can’t even see it) but they work fine when I switch it out for the 2.4. I know this is a very noob question, but can the older clients (non N) work on the 5.0 module)
    I have looked through a ton of documentation but there doesn’t seem to be a configuration guide that I can find for what I need to do.
    That’s it. Can someone please have mercy on me and point me in the right direction? I will be looking in the mean time but I have a lot of unknowns. I think if I can get the two questions answered above, then I can mark as resolved and run with it.
    Thanks a bushel,
    dt

    Hi Dave,
    1. Yes, the conditions for a proper roaming are : same SSID, same security settings, and the APs serving the same client subnet (so that client doesn't have to change its ip address).
    This is sufficient for data, Fast roaming is required for applications like voice and you can then look into using cckm as key mechanism and configure one AP to act as WDS to centralize the roaming keys.
    2. This is not related. 11n is available on both 2.4 and 5 ghz band. The question is if your old adapters are capable of 802.11a or not. 11a is the 54Mbps speed in the 5ghz band. I would guess they are not capable of it.
    Adapters that are on laptop now are often "abgn" meaning they can do N speeds on both 2.4 and 5ghz band. An adapter that would be "bg" or "bgn" would typically be restricted to only 2.4 Ghz.
    Hope this helps,
    Nicolas
    ===
    Please rate answers that you find useful

  • BPM design -help

    Hi all,
    i need you your help in enhancing one existing BPM.
    the initial state was
    file sys-> BPM -> sap R3 (system A) and also sap R3 (system B)
    where the BPM is   --> recv > sync send(A)->send(B)
    file sys send ONE vendor_key in xml format to BPM.
    now sysnc send is conected to R3 A through a RFC_A, which send one key field to RFC_A and get the whole record of a Z-table
    through that very RFC_A
    this whole record is then sent to another RFC_B thorugh send(B), which update a Z-table in the second sap system B.
    if the picture is clear, then the requirement is that:
    this time i have to design a BPM which will receive one xml file from file-sys, in which there will be multiple vendor key
    instead of one.
    the xml message must undergo 1:n transformation in bpm to craete xml messages containing one vendo key each.then parallely calling RFC_a with vendor key , get the reponse record from system R3 A,  and call RFC_B to send the record to system R3 B.

    HI Abhishek,
    Thanks for your response. Pls find below my BPM Design Details
    Block 1
    Step Name : Block1
    Exceptions : runTime
    Transformation
    Step Name : Transformation1
    Exception : System Error - runTime
    Exception Branch
    Exception Handler - runTime
    Control Step
    Setp Name : Control0
    Action : Throw Alert.
    I have followed the blog : https://www.sdn.sap.com/irj/scn/weblogs?blog=/pub/wlg/3465. [original link is broken] [original link is broken] [original link is broken]
    Still the alert is not getting triggered.
    Could you pls guide me, whethere is there any change need in my above design.
    Regards
    Mani

  • Dreamweaver & BC product option design help

    Hi everyone, hope we are all well?
    I have been building non e-commerce websites for a long time, i would say im above average at the job but i need some help as i take on my first e-commerce.
    Im using Business Catalyst and Dreamweaver CC and the site is for my new business, what im aiming to do may be reaching for the stars for someone with my experience but this is where i hope you clever boys and girls can help me out.
    I want the create a product page where the customer can configure their purchase, but i want to make it extremely user friendly. Im selling a lot of cool products but the focus of this part is built to order computers, i want to create a check out so only one option (ie. processor, hdd, case etc) is up at a time almost on different tabs, then you hit next/ back to move on/or back is this possible? Its like Dell/Alienware's old configuration, It would also be nice to have the price update as they select an option.
    I have set up all my products on BC and before i go any further with designing my site i wanted to get this bit nailed, so any ideas?
    Sorry if this is the wrong place to post but im sure dreamweaver has something to do with it,
    Pulled this of the net, so it looks like this....
    Any help would be a great help :-)
    Have a good one.

    Thank you

  • Background images/designs, HELP!

    I need help.
    This is in a very basic form from when I was playing around getting ideas prior to even working in DW... I promise you it is 100X better lol but basically I'm trying to set up a website to look like this:
    I have it set up in Dreamweaver currently with that outside border in separate cells in a table and they all line up now and work nicely and the large center white box where the text is going is is in the center cell. However, my issue is that I can't put the text over this now. How do I do this? There HAS to be a way to put the outside border and the inside white box in the background so I can still layer the text over them. I tried setting them as the page background but they are stuck to the left and I can't move them to the center.
    I hope I explained it well enough. Does anyone have any ideas? This is holding up the rest of the website because I cannot figure it out
    This is the first website I have done outside of class and my professor that taught the web design class openly admitted that she doesn't know dreamweaver well at all and basically we had to teach ourselves out of a book and online videos (which is why I am having this issue) and of course, websites are my weakest point. It was a waste-of-money class but unfortunately was a required one.
    Any help/ideas/tips/tricks/etc would be GREATLY appreciated!!!
    PS: What are the really good tutorial websites for dreamweaver?

    As Fiona said, you need to be able to work with Code View.  If you don't spend some time learning basic HTML and CSS first, DW will punish & frustrate you no end.
    Start here: 
    http://w3schools.com
    3-Image Slices in a CSS layout
    http://alt-web.com/DEMOS/Image-slices-in-a-CSS-based-layout.shtml
    More advanced
    Taking a Fireworks or Photoshop comp to a CSS based layout in DW
    http://www.adobe.com/devnet/fireworks/articles/web_standards_layouts_pt1.html
    DO NOT USE LAYERS until you understand how they work.
    Absolutely Positioned Divisions or DW "Layers"
    http://apptools.com/examples/pagelayout101.php
    Nancy O.
    Alt-Web Design & Publishing
    Web | Graphics | Print | Media  Specialists
    www.alt-web.com/
    www.twitter.com/altweb

  • FDF & LiveCycle Designer - HELP!

    Dear all,
    I think I'm becoming insane. I have forms created in LiveCycle Designer 8,
    and I need that one of the text fields will be filled in automatically.
    Its value (for example, "123456") is supposed to be based on a PHP Session.
    I've found this great tutorial: http://koivi.com/fill-pdf-form-fields/,
    only to find out later that it only works in forms created by Acrobat itself, and my question is: WHY?!
    I have a dead-line to finish the project I need it for,
    and I'll be kicked out if I won't find a solution to that issue until then.
    Please, I beg you, help me with your kindness and wisdom to find a solution, since I'm currently at a dead-end with no turning back.
    By the way, the funny, ironic thing is that I usually work in a web environment, using HTML, (Web) JavaScript and PHP to create forms with validations. The only reason we turned to the PDF technology is because
    we need an image of the submitted form, and the digital signature as a
    proof, in case patients in the research will decide to sue us for damages.
    Thank you so much for reading,
    Liron Sin-Shmuel, Web Programmer,
    University of Haifa, Israel.
    E-mail: [email protected]
    Cellular: +972-52-6240900.

    Thank you, Tembowa, but unfortunately, I don't understand a thing of the script you wrote. I need to do the whole procedure of implementing the Study ID on server side, using PHP, and I'm out of ideas.

Maybe you are looking for