Dc7700 small form factor - I get 9 red led flashes when trying to turn on computer.

I have replaced the power supply and I continue to get the same 9 red flashed.
If I push the power button twice in rapid succession I get a green led but I do not get any monitor feed nor does the hard drive get accessed for booting.
Please help!

Hi:
9 beeps could mean:
1. Check the voltage selector (red switch) on the power supply to make sure it is set for the right voltage.
Unplug the A/C power cord from the PC and wall socket. Change the voltage switch to the correct voltage.
Wait 30 seconds and plug the PC back in.
2. Replace the system board.
3. Replace the processor.
Please see the troubleshooting guide, Table A-2 at the link below.
http://bizsupport2.austin.hp.com/bc/docs/support/SupportManual/c01302202/c01302202.pdf
Paul

Similar Messages

How to update firmware for HP Compaq DC small form factor

I have HP Compaq dc7700 small form factor, Windows xp pro. It was bought on ebay and works fine except for one thing. The Bios was upgraded but the firmware is not upgrading. the Bios was upgraded to V3.05 but the firmware remains 2.04
I downloaded al the updates and firmware and followed instructions but I seem to have problems updating the firmware. I would like to know how to do this step by step because the instructions I read seems to be missing some steps. my question is how to update the firmware. I did read the instructions but could not get it updated. either updating via windows or in dos, I can't seem to make it successful. There are two error messages,
1. ME BIOS Extension module has halted. Update BIOS or Management Engine firmware if problem persists.
2. Amt mamagement engine is disabled.

HP normally uses the term BIOS to refer to motherboard/CPU "firmware" updates and Firmware to refer to other device "firmware" updates... Below is a list of the two classes of firmware;
BIOS
Business Desktops BIOS Utilities 4.02 Rev. A
Microcode Update for HP 786E BIOS Family Computers with Intel Processors 1.06 Rev. A
HP Compaq Business Desktop ME Firmware Update and Utilities 2.2.30.1046 Rev. A
HP Compaq dc7700p Business Desktop System BIOS for Intel vPro Technology (786E1 BIOS) 3.05 Rev. A
HP Compaq Business Desktop System BIOS (786E1 BIOS) 1.15 Rev. A
Firmware
Western Digital 7200-rpm Hard Drive Firmware Update 3.03E03 Rev. A
Intel PRO/1000 Firmware 1.10 Rev. A
HP Optical Drive (TSST H353B DVD-ROM) Firmware Update BC08 Rev. A
HP Optical Drive (TSST H653N DVD-RW) Firmware Update HB02 Rev. A
Seagate Hard Drive Firmware Upgrade for 500-GB Barracuda 7200.11 HP13 Rev. A
ATI X1600XT Graphics Card Video BIOS Update S3A67124.104 Rev. A
Samsung Hard Drive Firmware Upgrade - SATA Drives 42_51 Rev. A
Please identify the exact device you wish to upgrade/update the firmware to.
Frank
Frank
{------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V
This is a user supported forum. I am a volunteer and I don't work for HP.
HP 15t-j100 (on loan from HP)
HP 13 Split x2 (on loan from HP)
HP Slate8 Pro (on loan from HP)
HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240

No Audio from HP Compaq 6000 Pro Small Form Factor PC display port

Hi
I have a HP Compaq 6000 Pro Small Form Factor PC that has a display port. I bought a display port-HDMI adapter to use it on my LG plasma TV. The video is fine but i get no audio.
Please what do i need to do? does my display port support audio? The symbol on it has the DP++ sign which indicates it should support audio.
Please assist me.

Hi:
To the best of my knowledge, your PC does not support audio out of the display port.
Check your sound and playback menu in the contol panel, and see if you have 2 HD audio selection choices. If not, you won't be able to get sound out of the display port.
Paul

HP ProDesk 400 G1 Small Form Factor Business PC using vga and dvi at the same time.

Looking into purchase a HP ProDesk 400 G1 Small Form Factor Business PC which has a VGA and DVI-D ports on the integrated video card. Can you use both ports simultaniously. one screen connected to vga and a 2nd monitor connected to the DVI port?

Hi,
You might get better assistance on the HP Enterprise Business Forum.
HP DV9700, t9300, Nvidia 8600, 4GB, Crucial C300 128GB SSD
HP Photosmart Premium C309G, HP Photosmart 6520
HP Touchpad, HP Chromebook 11
Custom i7-4770k,Z-87, 8GB, Vertex 3 SSD, Samsung EVO SSD, Corsair HX650,GTX 760
Custom i7-4790k,Z-97, 16GB, Vertex 3 SSD, Plextor M.2 SSD, Samsung EVO SSD, Corsair HX650, GTX 660TI
Windows 7/8 UEFI/Legacy mode, MBR/GPT

Dekstop DC7800p Small Form Factor system

Hi,
I've got a dc7800 Small Form Factor system. It was working fine but after a reboot it won't start up normally anymore. The black POST screen appears, RAM testing starts to count up and then I see and error about "system options not set". After less than a second, a blue window in the middle of the screen displays the message "smart card authentication" and below that, "smart card reader not present".
From a bit of reading it seems like a BIOS problem but I can't figure out how to really reset the CMOS and get things working again. I've tried removing the CMOS jumper and booting the system, removing the power cord and CMOS battery for 10 minutes.
Is there a way to do one of the following:
- force the CMOS defaults to reset and remove the configuration that requires the smart card authentication?
- force a BIOS recovery, with a key combination or by using a different jumper or jumpers on the motherboard?
I see various other jumpers and pads on the motherboard like "ROM RCVRY" and the E15 Boot Block Recovery Header but scant information about how these might be used to solve the problem.
It seems to me that the hardware is fine as it powers up and displays the POST screen. It's like a BIOS setting has been reset to require a smart card, even though there isn't one, nor even a smart card reader, in the system.
Any advice would be greatly appreciated.

After doing some research on the message, I came across this post.
Apparently, your PC has a smart card optional system (maybe it was government surplus).
http://h30499.www3.hp.com/t5/Business-PCs-Compaq-Elite-Pro/DC7800-smart-card-athentication/m-p/10691...
Now, if you can get into the BIOS menus, if you look at the top of page 8, you will see what you need to do in order to enable/disable the smart card reader message.
http://bizsupport1.austin.hp.com/bc/docs/support/SupportManual/c01162201/c01162201.pdf
Whatever the problem is, it is a security setting issue, and clearing the CMOS or updating the BIOS will not have any effect on that setting.
Unfortunately, I have no experience with the security settings or protect tools software on HP business PC's.
I have a dc7800 (and only use HP business desktops and notebooks), so I am very familiar with all the other aspects of the PC, but that one.
You may want to post your issue on the HP business support forum, business PC section. Hopefully someone there has experience with turning this feature on or off.
http://h30499.www3.hp.com/t5/Business-PCs-Compaq-Elite-Pro/bd-p/bsc-271#.Uk2rcJAo69I
You may also want to log in and reply to that post, but don't get your hopes up that it will be answered.
RichS hasn't replied to a post in 3 years. Although someone else may.
Good luck, and please post back if you find the solution to the problem.

Dual monitors HP Z200 Small Form Factor Workstation

I am waiting on my new Intel I-5 HP Z200 Small Form Factor Workstation running Windows 7. What do I need to run two monitors?  I believe that there is an HDMI and a DVI video output on the rear - can I run two monitors off of these two outputs or do I need a video card? If I buy a video card do I need one with two HDMI outputs (my preferred connection) or can I use the one on the motherboard and one on an add in card siumultaneously?

Hi,
For that card, with the right connectors and adaptors you can connect to TWO minitors ( Drive up to two 30-inch (2560x1600) digital displays through native dual DisplayPort connectors on a low-profile card.):
    http://www.nvidia.com/object/nvs-310-graphics-card.html#pdpContent=2
Bau you can add an adapter such as:
     https://www.youtube.com/watch?v=ZkbaXkMQrIM
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Hp pro 3130 small form factor freezing

Hey guys, I recently rolled out a HP Pro 3130 Small Form Factor PC to a client a month ago and they have been experiencing constant freezing. Basically the whole PC locks up and nothing can be done to revive it aside from a complete Power Cycle. As an IT Professional, I have done significant investigation and troubleshooting and have not been able to come to any conclusion. It appears to be completely random with no patterns (eg particular application or time) and happens several times a day. I have done the following: - checked event viewer for errors or warnings (none) - checked to see if a dump file is created (none) - run a CPU Stress test and monitoring the temperatures (max 70C) - run a RAM test (memtest) with no errors reported - run a HDD test (spinrite) with no errors reported - run a windows system file check (sfc) with 100% valid file integrity - downloaded and installed latest drivers - installed latest windows updates I feel I have exhausted all options short of either a complete OS reload (i would prefer not to do) or a warranty return. Any ideas?

Hello RTerrell,
If your computer is locking up and there are bands of lines going down the screen then something is failing hardware wise
1. Memory
2. Video Card
3. Power Supply
There could also be bulging capacitors on the boards.
The best thing is to start ruling out hardware components by swapping in new ones. The power supply being the first easy one. Then try with one stick of RAM at a time, try replacing the RAM with other RAM. Finally replace the video card. If it's still failing after that then it may be the motherboard, but I'm hesitant to think that.
If I have helped you in any way click the Kudos button to say Thanks.
The community works together, click Accept as Solution on the post that solves your issue for other members of the community to benefit from the solution.
- Friendship is magical.

3548-XL-EN to switch with small form-factor pluggable (SFP) ports

Is it possible to connect my 3548 with a WS-G5484 directly to a 3560-24TS
with small form-factor pluggable (SFP) port?
thanks

Yes.. You will need a LC-SC connector. The part number for a 10-Meter Fiber Multimode SX LC-to-SC Connectors is "CSS5-CABSX-LCSC"

What replacement power supply for m72e small form factor

Simple question
I have a bunch of lenovo m72e small form factor pc's.
is the power supply a standard tfx or some sort of proprietary system.
I was thinking of upgrading and also preparing for furture failure contingency.

Many thanks for the update. it is as i feared. i hate the proprietary major components.... oh well, thank goodness for ebay.
also, much less important as I figured out how to sysprep a machine to move windows recently. Since our office FINALLY migrated to windows 7 x64; any future upgrades will be fairly easy on a modern OS.
The m72e we purchased have 3 years support build in so it should be a while before I have to worry about servicing them.
Having said all this, the Dell vostro 200 systems we have are 7 years old and trucking along with no service issues so far.
Lenovo machines were cheaper / on sale at the time and dell has since discontinued their vostro line so we tried the switch over on 1/2 our workstations @ the office.
The speed of the system is fine but there are certainly some bios/hardware bugs that we have noted around the network card.
I doubt we will transition the rest of the systems to lenovo at this point. Sure is easy to service when all your systems are from 1 vendor and the exact same lineage though.

Random, excruciatingly slow load time with 7900 Elite small form factor desktops

Hi all, I have approx 300 HP 7900 Elite small form factor machines in my environment that were deployed just over two years ago. from the time of deployment we have experienced on about 50 occasions a random, excruciatingly slow load time that take about one hour for the user to login and open their programs. there has been no rhyme or reason for it, different floors, areas of the building, etc. I searched the forum for similar probs and didn't see one like this, I hope I'm not duplicating efforts from someone else's question... One thing we have noticed is that if we re-boot while it is going through the start-up process, it seems to "make it angry" and will lengthen the overall load time. We use the 32-bit Vista Enterprise OS. This is with a "stock" build, that is to say, our standard corporate build. our security policy does not allow users to install software, by the way. Thanks so much if you can help!

Hi,
How is the issue going? Usually, this error can be caused by missing third-party NIC driver. To solve the issue, we can download the missing network
driver and update the WDS boot image to include it.
In addition to the article provided by Chris, the following blog can also be referred to as reference.
http://askmetricks.blogspot.in/2013/03/solvedwdsclient-error-occurred-while.html
Please Note: Since the web site is not hosted by Microsoft, the link may change without notice. Microsoft does not guarantee the accuracy of this
information.
Best regards,
Frank Shen

No sound output on installing a hdmi support graphics card on HP Compaq dc5800 Small Form Factor

when i inserted a HDMI support graphics card on g-force nvidia on my HP Compaq dc5800 Small Form Factor no audio output was availabe i need a support for this problem

You will have to switch the sound Playback from Speakers to the Digital Audio output.
Disconnect the speakers from the default output at the rear of your PC. Sound will be output through the HDMI cable to the device it is connected to if the video device has HDMI sound capability. If you have it connected to an HDTV it should not be an issue. All you will have to do is use the TV's menu to accept the computer input instead of cable.
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

On My Mac Pro Getting an unknown error message when trying to update apps

On My Mac Pro Getting an unknown error message when trying to update apps To Perchase Mountain Lion

Try signing out of your account, restart the iPad and then sign in again and see if that works for you.
Settings>Store>Apple ID - tap your ID and sign out.
Restart the iPad by holding down on the sleep button until the red slider appears and then slide to shut off. To power up hold the sleep button until the Apple logo appears and let go of the button.
Sign in again -Settings>Store>Apple ID - sign in.
If that doesn't work either, reset your iPad and see if that helps.
Reset the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons.

I keep getting an "Update Failed" message when trying to update my apps using Creative Cloud.

I keep getting an "Update Failed" message when trying to update my apps using Creative Cloud.

[ Mac 10.9.3 / Indesign CC update fail / Premiere update fail / Adobe Media Encoder 7.2.2 update fail ]
Adobe Media Encoder was the problem for me. There's no separate uninstaller for AME. My ID CC and Premiere couldn't be updated (for the AME7.2.2 update as the only change). MCMHMPEGVideoCodec.framework seemed to be the factor.
I uninstalled Premiere (only), after having manually removed MCMHMPEGVideoCodec.framework from inside AME. After boot I installed it again and voilà, both (ID & Premiere) updates went trough fine. The MCMHMPEGVideoCodec.framework was on place inside AME too.

Red LED flashes continuously

I have the BlackBerry Bold 9650, it's a CPO purchased a year ago, used off and on till June, and has been my primary phone since June. Up to now it's been fine, and I've gradually added apps and goodies... Anyway, the last couple of days, it seems when I get a phone call my LED will flash red, endlessly. I cannot find a way to get it to stop short of pulling the battery, and my battery depletes quickly if I don't do this. **additional info - the touchpad becomes very sluggish as well, once I receive a phone call after a battery pull. This is getting to be a bit more than an annoyance, having to pull the battery after every phone call.
There have been numerous app updates the last couple of days too, and one was for BeBuzz, so I'm thinking maybe that's the culprit. It seems to be working normally though (the customized lights for contacts I have set do work) and I've gone through settings and don't see what it could be.
Anyone else have any ideas? Or a simpler/faster way to get that red LED to stop flashing? I checked all messages, emails, missed calls, etc and I cannot figure out what is making the LED blink so I can shut it off!!

MarquiaF_VZW wrote:
Hi SuzyQ! I'm used to you resolving everyone else's issues, (LOL, yeah, me too!) so I'll be more than happy to help you with your Blackberry. First, I just want to make sure you have the latest software version on your Bold, which was released 1/10. I believe that update was for the 9930 - I've got the 9650. I am running OS 6.0 and it says my software is up to date. If not, here are some options to manually download the update and also a list of the benefits of the update. If you do have the update already, do you notice this starting afterwards?
Do you have any missed calls, voicemails or new emails when this happens? No, I check all of those and cannot find anything I haven't opened or checked! That's the frustrating part - not knowing why that light is flashing so I can turn it off. Try removing BeBuzz to see if the LED is still flashing and keypad sluggish after receiving calls. I may just have to do that, though I'm using the paid version - I'll back up all my contacts first because I do NOT want to have to set them all up again. I don't get a lot of phone calls - mostly text and email, but it's annoying when it happens.
I have not seen any other reports of this issue. If the issue is still occurring after updating software and removing BeBuzz, then I suggest backing up the phone and completing a security wipe on the Blackberry. Would really rather not go there if I don't have to! Make sure to test making and receiving calls before restoring your data, to make sure no corrupt data is restored. I would recommend backing up just the important info like contacts, calendar, emails, etc.
MarquiaF_VZW
Follow us on Twitter @VZWSupport
Thanks for the response Marquia - I was just thinking it hasn't happened today, but then, I haven't gotten a phone call today either. So it may still be an issue. I think I'll wait a few more days and see if it continues to happen or if it was just a weird glitch. I really am enjoying the Bold, and this is really the first problem I've come up against! I'll let you know when / if it gets resolved and what works or doesn't work.

I get error message "unknown error" When trying to log on to itunes via pc, help please!

I get error message "unknown error" When trying to log on to itunes via pc, help please!

Hello, trolle56.
Thank you for the question. You may find these articles helpful in troubleshooting the error received with the iTunes Store.
Can't connect to the iTunes Store
http://support.apple.com/kb/ts1368
iTunes: Advanced iTunes Store troubleshooting
http://support.apple.com/kb/ts3297
Cheers,
Jason H.

Dc7700 small form factor - I get 9 red led flashes when trying to turn on computer.

Similar Messages

Maybe you are looking for