DCNM compatibilty with nexus 2000 and 5000 series

Hi,
I would to know if the DNCM can manage a Data Center composed with Nexus 2000 & 5000 series only!
Kind regards

Hi reswaran,
The features are:
- Automatic network discovering and real- time topology.
- Network anomaliy detection (threshold, alarms, errors, ...)
- Use email or aletrs to notify notify operations staff of critical outages thant may be service-imapcting
- Centralized administration interface, with acces via web
- Securised acces and rights managment
- Stock of data in an exportable database
- Quick, simple qnd transparent deployment
- Monitoring WAN bandwith usage
- Configurable report generation
- Generation of the performance reports
- Provide network map
- Support several network unit
- Intergrated Syslog server
- Polling andt  monitoring SNMP trap alarms
- Secure config distribution
- Support 200 devices
What kind of NMS can you recommend?
thanks a lot

Similar Messages

  • Differences Between WLC 2000 and 4400 series

    Besides the supported number of access points, what are the differences in features between the WLC 2000 and 4400 series?

    On the 2006, you have 4 ports on the back, that can support up to 3 AP's being directly connected, and the other port as your connection to the network, and it does not support LAG (Link AGgregation). The ports are 10/100M, and it can not be an anchor for a mobility group.
    On the 4400, you either have a 4402 or a 4404,the 2 has 2 Gig interfaces, and the 4404 has 4 Gig interfaces, you can not connect AP's directly to a 4400. Both 4400's will support LAG, and they can be used as anchors in a mobility group. Those are the big differences in them. They configure up the same, and interact with the wired and wireless networks the same.

  • VN-Tag with Nexus 1000v and Blades

    Hi folks,
    A while ago there was a discussion on this forum regarding the use of Catalyst 3020/3120 blades switches in conjunction with VN-tag.  Specifically, you can't do VN-Tag with that Catalyst blade switch sitting inbetween the Nexus 1000V and the Nexus 5000.  I know there's a Blade switch for the IBM blade servers, but will there be a similar version for the HP C-class blades?  My guess is NO, since Cisco just kicked HP to the curb.  But if that's the case, what are my options?  Pass-through switches?  (ugh!)
    Previous thread:
    https://supportforums.cisco.com/message/469303#469303

    wondering the same...

  • Communication problem with FP-2000 and Labview 7.1

    I am using the FP-2000, DO-403 and TC-120 modules with Labview 7.1, being run on a host computer via an ethernet connection.  The setup has operated flawlessly for ~2 years; recently, I have noticed that while a VI is running on my PC, connection to the FP module ceases.  There is no pop-up "connection error" in my VI, and the all the power and status LEDs on the FP modules are normal.  I can still interact with the VI on the front panel while it is running, but nothing is passed to the FP module.  I have tried communicating with MAX when this occurs and receive a "no connection" message.  Is there a simple solution here, such as rebooting the FP module?  Or is it time to invest in new hardware?
    Justin

    I am having a very similar problem with my cFP-1804 and Labview 7.0.  I have no problem initiating communication over ethernet, and the vi will run perfectly for hours or even days.  Inevitably, however, at some point there is no longer communication with the cFP-1804.  Data is no longer being passed either to or from the cFP-1804, and MAX will show that the device is not connected.  I also will not see any pop-up error message that says the connection has been lost, either from Windows or from Labview.  The vi will just continue to run as if nothing has happened.  Turning the power to the cFP-1804 off and then on will always resolve this problem.  Since I am using the cFP-1804 primarily for data logging, however, this behavior is particularly problematic as the system will record nothing but zeroes until I discover that the communication has been severed and perform the manual power cycling.
    I have been unable thus far to determine the cause of this problem.  Any help would be greatly appreciated.
    Thanks,
    Derrick

  • Report generation toolkit problem with office 2000 and office XP

    Hello, I am having a problem with running my vi after it is compiled with application builder. The dev machine is an XP box and the targer is windows 2000. I included _Excel Dynamic VIs.vi and _Word Dynamic VIs.vi from the office 2000 section of the install cd (for the report toolkit) in the compile but did not include those files for XP. When I run the application on the target machine (2000), the reporting functions call Excel just fine and the program does not come up with any errors. The program however, is not loading the approprate template and inserting the approprate data. Did I leave some neccessary files out of the compile? Thanks in advance!
    Greg
    Gregory Osenbach, CLA
    Fluke

    Hi Acer,
    The recommended procedure in your case is to install Microsoft Office 2000 on the development machine and then reinstall the LabVIEW Report Generation Toolkit. When the toolkit is installed, it will check for the current version of Office and install the corresponding VIs to support it. The VIs include different ActiveX calls according to the version of Office. Therefore it is not enough to change the support manually without having the correct version of Office installed first.
    However, I would recommend that you just try to run your executable on a machine that has Office 2000 installed. The difference in the ActiveX API for Office XP and 2000 is not that significant, so your application might work perfectly on an Office 2000 machine. If you try to run the executable on a machine with Office 97 installed I'm willing to bet my right arm that you will experience errors.
    Good luck Acer!
    - Philip Courtois, Thinkbot Solutions

  • Printer compatible with Windows 2000 and Windows 8 operating system?

    My office needs to access a terminal server hosted offsite.  The terminal server uses Windows 2000.  My laptop is Windows 8.   Since I upgraded my laptop I am no longer able to print.  Do they make a computer that is compatible with both versions of Windows?  Is there a fix?  I should also mention, I purchased a new HP and it wouldn't work either.  augh!

    Windows 2000 has been successfully tested with the AT interface card. The file: "Win2000Issues.rtf" (located in the "nifbus" directory) illustrates how to install the AT-FBUS interface card under the Windows 2000 platform. However, the PCMCIA-FBUS card is not supported at this time. In order to use the software under Windows 2000 the "MFC42.dll" file must be in the same folder as the Configurator, otherwise display problems may be experienced.
    Windows ME has also been tested with both the AT and PCMCIA interface boards and appears to work well. Additionally, the Configurator software has proven to be stable under ME.

  • What are the major differences between Nexus 55xx and MDS series w.r.t FC/FCoE/FCIP, scalability etc. ?

    Please share any link which tells this and which switch to go with? 

    In the inital post where I put "
    The N7K sees the server MAC in the FIP snooping, it also sees the 5548  as it's FCF.  But the 5548 vfc is stuck in "initializing".
    I meant to put N4K...not N7K...sorry about that.

  • MS-6167 problem with Win 2000 and Winxp

    Guys, I am having a problem. After I have installed Win2000 or Winxp Pro( first time boot, it pop blue screen with the msg systemroot\system\ntxxx.dll..I have to turn off and and turn on computer, it let me to boot up.) After that, when I restart the computer it boot up with blue screen(Sometimes, it let me boot up without any problem). I didn't install any third party software(OS only). It's weird. Even though, I have installed FAT file system and the result is the same.  I have tested windows 98. It's very stable and no problem at all.Here is my PC configuration
    AMD 950
    MS-6167
    Creative TNT2 Ultra 32MB(AGP)
    Sound Blaster Live
    Sony DVD ROM
    External Modem.
    Other than that, I build another PC for my fren here is the configuration
    AMD 1.7 XP
    MSI KT3 ULTRA
    Winxp Pro
    Any clue? Do I need to update bios? But I can't find MS-6167 model bios. How come it's doesn't support win2000 and win xp? I got another PC AMD 1.1 Thunderbird with ASUS A7V. I don't have any problem that I mentioned above when I installed 98,win2000 and winxp pro(Separately not dual boot). Appreciate !!!!
    Guanyu

    heres what i found for another guylink

  • Excel activex call changes between Office 2000 and Office XP. How does one manage that?

    I have several Active X calls from within a VI. One in particular is
    the Excel Cell Value property node in Office 2000. MS has decided to
    call it Excel Cell Value2 in Office XP.
    I have built and exe on a machine with Office 2000 and can run the code
    on a machine with Office XP, but I can not build on the machine with
    Office XP. I can also run a VI with that call
    on the Office XP box, but if I mass compile the VI I get the broken arrow.
    I guess I am confuesed as to why it can run but not compile. If the
    ActiveX call is not there for the compile why is it there for the run?
    If I can expect this does it work in reverse where I
    build on an Office XP box and run on a Office 2000 box?

    These problems you are experiencing do stem from the ActiveX changes between Excel versions.  When you mass compile LabVIEW checks to see if everything is linked correctly, including ActiveX portions of your code.  Since there are slight changes the LabVIEW compiler detects something is wrong, but cannot isolate the problem.  You might need to force a recompile of that VI.  Check out this link.
    http://digital.ni.com/public.nsf/websearch/50D06DEE8B9DC018862565A0006742F2?OpenDocument
    Hope this helps!
    Andy F.
    National Instruments

  • Correct ITunes version for Windows 2000 and Nano

    My daughter just got a Nano for x-mas and is not recognized by old I-tunes software. I assume I need a newer version. However, 8.x that is advertised as latest version does not mention Windows 2000. I can't find any info on what version of ITunes I need or if there is one even compatible with both 2000 and the Nano. Can anyone tell me? I am incredibly frustrated by the lack of info on this and the lack of info in the user's manual. I see there are several different versions/generations of Nano, but have no idea how I am supposed to know what I have. I am not computer illiterate, but find this site poor at explaining questions like; how to tell what generation of Nano one owns, what version of I Tunes is necessary to synch with that version of Nanao, and is that version of ITunes compatible with ones operating system.
    Can someone tell me what version of ITUNES I need (or if it is even possible)and where I can find it? Thank you if anyone can provide this info that Apple chooses not to make easily accessible.

    So does this mean the IPOD is useless unless I get a whole new operating system so I can get the latest ITUNES?
    I also found a fact sheet about what to do to re-install USB drivers if the IPOD isn't recognized by the computer (which it isn't), followed the instructions and it still is not recognized! Is there a place those drivers can be downloaded so I could try something other than ITUNES for putting music on?
    I still contend that MAC does a horrible job of explaining these issues to people when they are buying. I've spent about 4 hours looking at help pages and have yet to see one that mentions minimum system requirements (ie Windows 2000 is not supported) and what, if anything can be done about it. I spent about a half hour trying to locate an e-mail help/customer service address to ask these questions and let them know about my frustration, but all I could find was the phone number, for which I only get one call! I don't have time to spend this much time trying to track this info down. My first computer was a MAC and talked for years about how great they were, but this lack of easy access to basic info/customer service has soured me on them. Sorry about the rant. Thanks for any help. While I am not a computer nerd, I work with them enough to know how to get around.

  • Floppy Disk drives for Satellite Pro 4200 and 4300 series

    I have four Satellite Pro laptops - a 4340, a 4310, a 4270 and a 4280 and I'm having difficulty getting the 4310 and the 4270 to recognise a particular FDD. My understanding was that Mitsumi D353G FDDs were compatible with these 4200 and 4300 series laptops but I can't get the 4270 and the 4310 to "see" them. They will both however "see" an alternative FDD I have - a Pansonic JU-226A202FC but I only have one of them and two laptops needing a replacement FDD. I have tried a D353G that I know works (from my 4280) in both the 4310 and the 4270 but to no avail. I'm keeping an eye out for another Pansonic JU-226A202FC FDD on ebay but no luck so far. It's so frustrating as I'm sure a D353G FDD should work in the 4270 and 4310 and I have two spare ones which I wanted to use. I've looked in TSETUP.exe and can see no settings I can change to make these laptops see the D353G FDDs so any help or insight greatly appreciated. Does anyone out there have a 4270 or a 4310 successfully running a D353G FDD or, is this a quirk and these two particular models were only made to work with a Pansonic JU-226A202FC FDD not the D353G FDDs? Any clues?

    Hello
    Unfortunately I am not technician but I assume that there is obviously some problem with compatibility. It is possible that pin assignment is different and you can not use them. If you want to have a precise explanation you should contact technicians. I am pretty sure that they have motherboard schemes and can give you a proper explanation and advice how to handle with this problem.
    Good luck!

  • NX7K M and F series mixed chassis best practice?

    I have NX7010 chassis' with mixed M and F series line cards. Fucntions to implement include VDC, vPC, VRF, and L3 routing. What are the best practices for mixed chassis? I once saw a Cisco document talking about it but couldn't find it right now.
    Thanks in advance                 

    Understand Layer 3 functions should be performed by M1 ports. But if I use F2e 10G ports to build a trunk between 2 NX7K, then use a SVI to make Layer 3 adjacency across this trunk connection, is it ok?
    I can use M1 1G ports to build this trunk too but I would prefer F2e 10G ports if this is ok.
    Thanks

  • HDMI port in Nexus 2000

    All models of the nexus 2000 has HDMI port
    Installation guide says it is for console connectivity. There was no special cable supplied with Nexus 2000.
    anyone tried to use that port? I want to what type of cable connector to use to console in to the FEX. Anyone knows what type of cable to use??
    I know FEX can be consoled in using attach fex 101 command on parent switch but then what is purpose of this HDMI port.

    Krunal,
    It is not an HDMI port, though it kind of resembles one.  This port is utility port used by manfucaturing & TAC.  As the N2K is managed by the N5K which has your traditional console port, it's not necessary for console access direclty to the FEX.  It's stictly for diagnositcs.  These ports are standard on FEXs including the IO Modules within a UCS Chassis.
    These cables are not supplied to customer or available for purchase.
    Regards,
    Robert

  • I have few questions to ask about the Expert Series and Valet Series

    Hello.
    I have few questions to ask about the Expert Series and Valet Series.
    1. I see there aren't any print server/bridge/access point for these two new series. Do I have to use previous ones? Or the new ones are in planned in near future?
    2. Do I "HAVE TO USE CONNECT SOFTWARE"?  Can I just use web interface to do every setting that these routers features?
    3. Does expert series routers support guest network and parental control?
    4. When I look into informations of these router, some router doesn't give information about backward compatible to older standards. Do I have to consider that as they are backward compatible with older standards?
    Ok, that's all for now.
    If I need to ask more questions I will do that in this thread as reply

    With the New Expert or the Valet Series Router, you still can use the Print Server / Bridge and Access Points.
    Well with the Expert and Valet Series router, you have an option to User Cisco Connect Software or you can User Web Interface of the Router. But with the Cisco Connect Software you have an Advantage of creating a Guest Account and using Parental Control , which is not available using the Web Interface.
    These both the routers are backward compatible and they can connect to your G Series Product.

  • Ask the Expert: Cisco Nexus 2000, 5000, and 6000 Series Switches

    with Cisco Expert Vinayak Sudame
    Welcome to the Cisco Support Community Ask the Expert conversation. This is an opportunity to learn and ask questions how to configure and troubleshoot the Cisco Nexus 2000, 5000 and 6000 Series Switches with Cisco subject matter expert Vinayak Sudame. You can ask any question on configuration, troubleshooting, features, design and Fiber Channel over Ethernet (FCoE).
    Vinayak Sudame is a Technical Lead in Data Center Switching Support Team within Cisco's Technical Services in RTP, North Carolina. His current responsibilities include but are not limited to Troubleshooting Technical support problems and Escalations in the areas of Nexus 5000, Nexus 2000, FCoE. Vinayak is also involved in developing technical content for Cisco Internal as well as external. eg, Nexus 5000 Troubleshooting Guide (CCO), Nexus 5000 portal (partners), etc. This involves cross team collaboration and working with multiple different teams within Cisco. Vinayak has also contributed to training account teams and partners in CAE (Customer Assurance Engineering) bootcamp dealing with Nexus 5000 technologies. In the past, Vinayak's responsibilities included supporting MDS platform (Fiber Channel Technologies) and work with EMC support on Escalated MDS cases. Vinayak was the Subject Matter Expert for Santap Technologies before moving to Nexus 5000 support. Vinayak holds a Masters in Electrical Engineering with Specialization in Networking from Wichita State University, Kansas. He also holds Cisco Certification CCIE (#20672) in Routing and Switching.
    Remember to use the rating system to let Vinayak know if you have received an adequate response.
    Vinayak might not be able to answer each question due to the volume expected during this event. Remember that you can continue the conversation on the  Data Center sub-community, Other Data Center Topics discussion forum shortly after the event.
    This event last through Friday July 12, 2013. Visit the community often to view responses to youe questions of other community members.

    Hi Vinayak,
    Output of "show cfs internal ethernet-peer database"
    Switch 1
    ETH Fabric
    Switch WWN              logical-if_index
    20:00:54:7f:ee:b7:c2:80 [Local]
    20:00:54:7f:ee:b6:3f:80 16000005
    Total number of entries = 2
    Switch 2
    ETH Fabric
    Switch WWN              logical-if_index
    20:00:54:7f:ee:b6:3f:80 [Local]
    20:00:54:7f:ee:b7:c2:80 16000005
    Total number of entries = 2
    Output of "show system internal csm info trace"
    Switch 1 in which "show cfs peers" show proper output
    Mon Jul  1 05:46:19.145339  (CSM_T) csm_sp_buf_cmd_tbl_expand_range(8604): No range command in buf_cmd_tbl.
    Mon Jul  1 05:46:19.145280  (CSM_T) csm_set_sync_status(6257): Peer RT status PSSed
    Mon Jul  1 05:46:19.145188  (CSM_T) csm_sp_handle_local_verify_commit(4291):
    Mon Jul  1 05:46:19.145131  csm_continue_verify_ac[597]: peer is not reachable over CFS so continuing with local verify/commit
    Mon Jul  1 05:46:19.145071  csm_tl_lock(766): Peer information not found for IP address: '172.16.1.54'
    Mon Jul  1 05:46:19.145011  csm_tl_lock(737):
    Mon Jul  1 05:46:19.144955  (CSM_EV) csm_sp_build_tl_lock_req_n_send(941): sending lock-request for CONF_SYNC_TL_SESSION_TYPE_VERIFY subtype 0 to Peer ip = (172.16.1.54)
    Mon Jul  1 05:46:19.143819  (CSM_T) csm_copy_image_and_internal_versions(788): sw_img_ver: 5.2(1)N1(2a), int_rev: 1
    Mon Jul  1 05:46:19.143761  (CSM_T) csm_sp_get_peer_sync_rev(329): found the peer with address=172.16.1.54 and sync_rev=78
    Mon Jul  1 05:46:19.143699  (CSM_T) csm_sp_get_peer_sync_rev(315):
    Mon Jul  1 05:46:19.143641  (CSM_EV) csm_sp_build_tl_lock_req_n_send(838): Entered fn
    Mon Jul  1 05:46:19.143582  (CSM_T) csm_set_sync_status(6257): Peer RT status PSSed
    Switch 2 in which "show cfs peers" does not show proper output
    Mon Jul  1 06:13:11.885354  (CSM_ERR) csm_pss_cmd_tree_walk_cb(2057): Parent command not found for cmd switchport mode trunk, cmd pseq 77 seq 482
    Mon Jul  1 06:13:11.884992  (CSM_ERR) csm_pss_cmd_tree_walk_cb(2057): Parent command not found for cmd channel-group 51 mode active, cmd pseq 357 seq 369
    Mon Jul  1 06:13:11.884932  (CSM_ERR) csm_pss_cmd_tree_walk_cb(2057): Parent command not found for cmd switchport trunk allowed vlan 2, 11, cmd pseq 357 seq 368
    Mon Jul  1 06:13:11.884872  (CSM_ERR) csm_pss_cmd_tree_walk_cb(2057): Parent command not found for cmd switchport mode trunk, cmd pseq 357 seq 367
    Mon Jul  1 06:13:11.884811  (CSM_ERR) csm_pss_cmd_tree_walk_cb(2057): Parent command not found for cmd description process_vpc, cmd pseq 357 seq 366
    Mon Jul  1 06:13:11.884750  (CSM_ERR) csm_pss_cmd_tree_walk_cb(2057): Parent command not found for cmd channel-group 51 mode active, cmd pseq 352 seq 365
    Mon Jul  1 06:13:11.884690  (CSM_ERR) csm_pss_cmd_tree_walk_cb(2057): Parent command not found for cmd switchport trunk allowed vlan 2, 11, cmd pseq 352 seq 364
    Mon Jul  1 06:13:11.884630  (CSM_ERR) csm_pss_cmd_tree_walk_cb(2057): Parent command not found for cmd switchport mode trunk, cmd pseq 352 seq 363
    Mon Jul  1 06:13:11.884568  (CSM_ERR) csm_pss_cmd_tree_walk_cb(2057): Parent command not found for cmd description process_vpc, cmd pseq 352 seq 362
    Mon Jul  1 06:13:11.884207  (CSM_EV) csm_sp_acfg_gen_handler(3011):  Preparing config into /tmp/csm_sp_acfg_1733916569.txt
    Mon Jul  1 06:13:11.878695  csm_get_locked_ssn_ctxt[539]: Lock not yet taken.
    Mon Jul  1 06:13:11.878638  (CSM_EV) csm_sp_acfg_gen_handler(2937): Recieved sp acfg merge request for type: running cfg
    Mon Jul  1 06:12:29.527840  (CSM_T) csm_pss_del_seq_tbl(1989): Freeing seq tbl data
    Mon Jul  1 06:12:29.513255  (CSM_T) csm_sp_acfg_gen_handler(3106): Done acfg file write
    Mon Jul  1 06:12:29.513179  (CSM_EV) csm_sp_acfg_gen_handler(3011):  Preparing config into /tmp/csm_sp_acfg_1733911262.txt
    Mon Jul  1 06:12:29.508859  csm_get_locked_ssn_ctxt[539]: Lock not yet taken.
    Mon Jul  1 06:12:29.508803  (CSM_EV) csm_sp_acfg_gen_handler(2937): Recieved sp acfg merge request for type: running cfg
    Mon Jul  1 05:53:17.651236  Collecting peer info
    Mon Jul  1 05:53:17.651181  Failed to get the argumentvalue for 'ip-address'
    Mon Jul  1 05:40:59.262736  DB Unlocked Successfully
    Mon Jul  1 05:40:59.262654  Unlocking DB, Lock Owner Details:Client:1 ID:1
    Mon Jul  1 05:40:59.262570  (CSM_T) csm_sp_del_buf_cmd(1713): Deleting comand with Id = 1
    Mon Jul  1 05:40:59.262513  DB Lock Successful by Client:1 ID:1
    Mon Jul  1 05:40:59.262435  Recieved lock request by Client:1 ID:1
    Mon Jul  1 05:40:41.741224  ssnmgr_ssn_handle_create_get: Session FSM already present, ID:1
    Mon Jul  1 05:40:41.741167  ssnmgr_handle_mgmt_request: Create/Get request received for session[process_n5kprof]
    show cfs lock gives no output.
    Just to further clarify, we have 4 5548UP switches in the same management vlan. 2 switches are in one location lets say location A and they are CFS peers and are working fine.
    These two switches which are having problem are in location B. All the switches are in the same vlan. Essentially the all CFS multicast messages will be seen by all 5548 switches as they are in the same vlan. I am assuming that this might not create any problems as we specify the peers in the respective configurations. Or do we have to change the CFSoIPv4 multicast addresses in location B or may be configure a different region.
    Regards.

Maybe you are looking for