DCP 5.1.4

Hi
I think I am of need of a bit of help. I am pretty sure I have used FCP since upgrading to Leopard but today when I tried to launch it I never even reached th splash screen stage. I have tried all the tried and r=tested remedies ie restart, repair permissions, delete prefs, delete and reinstall FCP then tried to launch before and after updating FCP. I then zapped the PRAM. I am at a complete loss I have not updated anything else on the computer. This is the message I get from console
+*07/11/2007 21:32:07 [0x0-0x5b05b].com.apple.FinalCutPro[602] couldn't load a cfm component -2851 (<Component>)!*+
+*07/11/2007 21:32:14 com.apple.launchd[120] ([0x0-0x5b05b].com.apple.FinalCutPro[602]) Exited abnormally: Bus erro*r+

I haven't read any of the posts on this forum about the complications coming from upgrading to Leopard on an FCP system because I'm not planning an upgrade anytime soon. But there's been a lot of posts about this. Have you searched the forum for these posts?

Similar Messages

[SOLVED]Can't print to my Brother DCP-7065dn after upgrade to systemd.

Hi All,
I have a pure systemd installation and I'm having issues printing. I have a Brother DCP-7065dn which works well on my Ubuntu laptop with the drivers availible from Brother. I downloaded and installed the drivers for this printer from the AUR and added the printer to cups (both lpd and usb). When I print a test page cups reports that the job completed succesfully but the printer does not print. Not sure what is wrong. Has anyone else had printing issues after upgrading to systemd? Any thought on how I can get this printer working?
Thanks
Edit: BTW. Brother offers deb and rpm packages for their Linux drivers. I installed the deb packages on an Ubuntu machine and I can print over the network (lpd) with no problems. I also installed the brother on may arch system using the wrong drivers just to see what would happen. Using the DCP-7045N Foomatic/Postscript driver I can communicate with the printer (progress) but printing a test page results in the printer spitting out a lot of blank pages. I can also print to an HP from my arch laptop with no problems. So the issue seems to be with the drivers for the Brother DCP-7065dn from the AUR. Not sure how I'm going to fix this. I can't install the rpm or deb packages on my machine. and I don't want to switch to a red-hat or debian system if I can avoid it.
Final Edit: SOLVED! I need to learn to go back and read comments. In the AUR there was a comment regurding this exact issue. I needed to enable multilib repository and install lib32-glibc. Now it works. \(^_^)/
Last edited by darthpenguin (2012-10-04 08:41:29)

Matthew Poor wrote:
The iMac spooled its print job, then replied "communication error". I repaired permissions, restarted everything, and same result.
Did you add the printer using Bonjour or did you select one of the IP protocols? If the latter, then you cannot use IPP. The Canon MF driver supports LPD or HP Jetdirect.
Matthew Poor wrote:
Updated to Canon driver 10.2.0, printer is still not appearing in the list.
If you mean that after you change the USE menu to "Select printer software" and the Printer Software window is empty, then try restarting your Mac. This can rebuild the printer list.
Matthew Poor wrote:
Both Canon MF background items are running according to Activity Monitor.
The new MF v10.x driver does not install or use the MF Background process. So this process is a leftover from a previous driver. I would therefore recommend you trash the older driver files and run the v10.2.0 driver installer again.
Depending on the version of driver you had installed prior to upgrading to Mavericks, the name of the folder can be different but will reside in /Library/Printers/Canon. Here you will see BJPrinter and IJScanner. Leave them alone and just remove the one or two that have MF in the name.
You then need to navigate to /Library/Launch Agents/ and trash any Canon plist file. Then restart the Mac and run the Canon MF v10.2 installer again and then see if you can add the MF8350.

Wraptor DCP plugin not working with AME CC 2014

Platform:
10.9.2 on a MacPro 2014, 64GB RAM, D500's 6-core
Issue:
Media Encoder hangs when rendering a 97 minute project as a DCP using wraptor plugin. Always gets to a different frame before stalling - furthest i've gotten is 25 minutes in.
I've also tested the Wraptor plugin on an older machine with an NVIDIA 4800 using CUDA and had the same result. As the source i've tried rendering from the timeline via dynamic linking AND from an assembled Quicktime - neither works, same symptoms.
Any suggestions / experience using Wraptor successfully on long files? (NOTE: It DOES work when rendering smaller portions of the film, but never for the full film).

Update: Haven't been able to complete a wraptor render on my MacPro late 2013/2014 at all - using hardware or software rendering.
Was able to complete a software render of a 97 minute project on a MacPro late 2009 but after playing it back at a local theater it was unusable for theatrical viewing. Compression was VERY noticeable in the shadows, especially during graphics sequences using After Effects light sources (completely unacceptable during these sequences).
Same project rendered using OpenDCP looked great.

Wrator DCP problems in AME CC 2014

DCP rendering fro AME is great, but I am having some problems:
1. Wrator DCP informs a fixed bitrate convertion of 250Mbps, but I am geting final DCPs with variable and very low bitrates, as 38Mkps or even lower.
EDITED: It seams that is not a problem at all. QuVIS claims to use a Quality Priority Encoding method, so encoding bitrates are variables up to 250Mbps aiming to a studio quality standard, and not fixed as I thought. Good indeed.
2. NeoDCP player won't play some DCP due to unmatched frame numbers form audio and video MXF
3. Render crashes sometimes with no apparent reason.
PS: I am using the new recomended update from QuVIS site: DCP Packaging for Adobe Media Encoder 8 | QuVIS

The problem of some players not playing (some) DCP correctly is related do unmatched number of frames not correctly informed in CPL files.
Some times Wraptor DCP produces a MFX sound 1 frame bigger than MXF video. I think it is related to original sound bit depth conversion (not sure).
One solution is (in the case of problems) to edit CPL XML file and change IntrinsicDuration parameter to correct represent audio MXF duration.
        <MainSound>
          <Id>urn:uuid:9d1b0299-0282-498d-bb29-849f8fee8af8</Id>
          <AnnotationText>DSC_5845_dcp_9d1b0299-0282-498d-bb29-849f8fee8af8_audio.mxf</AnnotationTe xt>
          <EditRate>24 1</EditRate>
         <IntrinsicDuration>1015</IntrinsicDuration>
          <EntryPoint>0</EntryPoint>
          <Duration>1015</Duration>
        </MainSound>
OR, even batter, use OpenDCP to repack audio and video MFX files in a new DCP, with a lot more.

Missing Wraptor DCP Format for Export

Good morning.
I have a fresh install of Windows 7 64bit and a new install of Premiere Pro CC 2014 8.1.0 (81) Build. When opening a previous project from Premiere Pro CC I do not have the Wraptor DCP format for exporting. If I create a new project and sequence and dump a video file on the timeline and try and export it's still not there. I checked the plug-ins/common folder and I do have the Wraptor.prm file in there. I've searched and searched the web and have not seen an issue like this before. I did see something from Oct about it not being supported yet, but I have a second Windows machine (Windows 7 64bit) that I installed PPro on and it's there. I should note that in Encore (build 8.1.0.122) I'm missing the Cinema System Preset with Wraptor DCP too. Is there a prerequisite for getting the DCP option that I missed? I don't remember doing anything special on the other machine for it. Also, to note, I have uninstalled both and reinstalled to make sure it wasn't a botched install.
Anyone have any ideas?
Thanks.

Solved my own issue. Apparently in the barrage of Windows updates I had not yet grabbed SP1. Once that downloaded Wraptor DCP was now a selection in both PPro and Encore. Anyone else that comes across this in Windows 7, make sure you have SP1 installed.

DCP 23.976 24p

I need to make a DCP from a 23.976 material I have no trouble with the video but last time i did the 0.1% time change to the audio I had lot of sync problem's.
I finally vent to some cinema sound guy who told me the only solution to the problem was using some Pro-toole ploug-inn. So we did so and it worked. It took like 8 hour to render the file, but it worked. This was a lot of trouble and expensive so I ask is there a way to do this in Audition?

Yes, I'd have you try two things
1) Restamp the sample rate that is in the audio file. This is the "Edit > Interpret Sample Rate" command. So if your audio is too fast, then set the sample rate to be 47952 instead of 48000, save the file and then try it in Premiere Pro. It will take a long time to conform in PPro. If your audio is too slow, then set the sample rate to be 48048 and so forth.
2) You can resample the file directly in Audition with its high-quality resampler by using the Effects > Time and Pitch > Stretch and Pitch. Look at the speed up or slow down presets, and adjust accordingly, paying attention to the new timecode duration shown in the effect.

How can I install a Brother DCP 165C printer that my mac is not finding?

I have just bought a DCP 165C second hand, so it doens't come with a CD for installing. I have however downloaded the driver for mac from the Brother website and installed it into my computer, and it said the installation was succesful. I then plug the printer to my computer, via USB, then I go to add my printer as I normally would and have; through preferences- but it's not showing up in Default. I have tried Advanced but I don't know what to put in the url because of course the printer doesn't have one, it's just there, connected via USB.
I have also resetted the printer system and now don't know what else to do.
I really need to print, please help!

catlopera wrote:
It just doesn't want to work...
It is not recognising anything and if I go to add printer, no printers come up.
I'm waiting for a new USB cable to see if that is the problem
I'm sure this is maddening for you.
To be sure the printer works, can you print a report, e.g., User Settings, using the LCD Panel?
Your screenshot shows the window titled, Install BrotherTWAIN, which is the software for the scanner. The window for the printer software title should be, Install BrotherCLDrivers. If you have not already done so, download the CUPS Printer Driver. Then install and try to add it in Sys Pref > Print & Scan. If the problem persists, try the Brother troubleshooting steps for print issues with USB connections.
As for the "Failed to connect to the device" error, that used to happen often with my Brother MFC device for the scanner. Turning the unit off, waiting 30 seconds, and then turning the unit back on works. However, my unit is connected to my network and I scan using other software, i.e., not the Brother Control Center software.
I just noticed that the USB port is inside the DCP-165c printer. You might double check that the cover is not pinching cable anywhere along its path.
HTH and Good Luck!

Need help to get my Brother DCP-J125 printer working again

I'm totally stuck here. I had this printer working and now after a few months it doesn't work anymore.
I tried it with/without usblp. Tried it by installing the drivers myself and by installing the drivers with brother-dcpj125 from AUR (and I did run the script that comes with the drivers). Readded printer several times, reinstalled cups several times. The printer doesn't print. I think cups doesn't find the printer... (The scanner works btw)
$ lsmod | grep usb
usb_storage 44760 0
usbhid 36812 1 hid_logitech
hid 85608 3 hid_generic,hid_logitech,usbhid
btusb 11892 0
bluetooth 193532 10 bnep,ath3k,btusb
scsi_mod 133152 6 uas,rts5139,usb_storage,libata,sd_mod,sr_mod
usbcore 147434 9 uas,ath3k,btusb,uvcvideo,rts5139,usb_storage,ehci_hcd,usbhid,xhci_hcd
usb_common 954 1 usbcore
/var/log/messages.log
Connecting the printer:
Sep 23 16:55:34 localhost kernel: [ 2855.013082] usb 2-1: new full-speed USB device number 3 using xhci_hcd
Sep 23 16:55:34 localhost kernel: [ 2855.029232] usb 2-1: ep 0x85 - rounding interval to 512 microframes, ep desc says 800 microframes
Sep 23 16:55:34 localhost kernel: [ 2855.029994] scsi8 : usb-storage 2-1:1.2
Sep 23 16:55:34 localhost mtp-probe: checking bus 2, device 3: "/sys/devices/pci0000:00/0000:00:1c.3/0000:04:00.0/usb2/2-1"
Sep 23 16:55:35 localhost mtp-probe: bus: 2, device: 3 was not an MTP device
Sep 23 16:55:42 localhost dbus[644]: [system] Failed to activate service 'org.freedesktop.Avahi': timed out
Sep 23 16:55:45 localhost kernel: [ 2866.038840] scsi 8:0:0:0: Direct-Access Brother DCP-J125 1.00 PQ: 0 ANSI: 2
Sep 23 16:55:45 localhost kernel: [ 2866.099179] sd 8:0:0:0: [sdd] Attached SCSI removable disk
Sep 23 16:56:12 localhost dbus[644]: [system] Failed to activate service 'org.freedesktop.Avahi': timed out
Disconnecting the printer:
Sep 23 16:57:37 localhost kernel: [ 2977.838261] usb 2-1: USB disconnect, device number 3
$ lsusb
Bus 002 Device 004: ID 04f9:0253 Brother Industries, Ltd
$ ls -l /dev/bus/usb/002/004
crw-rw-r-- 1 root lp 189, 131 23. Sep 16:59 /dev/bus/usb/002/004
# lpinfo -v
network ipp
network beh
network smb
network http
network socket
network https
network lpd
network ipps
file cups-pdf:/
direct hp
direct hpfax
$ /usr/lib/cups/backend/usb
DEBUG: list_devices
DEBUG: libusb_get_device_list=13
DEBUG: Switching USB device configuration: 0 -> 1
DEBUG2: Printer found with device ID: Device URI: usb://Unknown/Printer
direct usb://Unknown/Printer "Unknown" "Unknown" "" ""
Any idea what's wrong? The printer worked perfectly a few months ago

nTia89 wrote:start posting the pacman's log....
This is everything I installed or upgraded since March. Do you need the whole log?
https://raw.github.com/gist/3d718d6781d … tfile1.txt
David Batson wrote:
You probably need to change the URI in CUPS. See the following for some tips.
http://welcome.solutions.brother.com/bs … prn1a.html
http://welcome.solutions.brother.com/bs … _prn3.html
I can select the driver for my printer when I modify the printer, but the "Connection" stays "usb:/dev/usb/lp0".
Last edited by slosd (2012-09-23 22:56:49)

[solved] printer - brother DCP-J315W - "sending data to printer"

Hi All,
My sister have a printer brother DCP-J315W, connected with usb.
I installed the brother-dcpj315w package from AUR, and it used to work without issue.
But I was informed "recently" that this printer is not working correctly since perhaps two months. (perhaps it's related to the AUR package update, but I think it's was already not working before the update.)
When I try to print, there is no activity on the printer, and, using the cups web-interface, I can see, for the printer status: "idle - sending data to printer"
I'm not sure about what I see in the logs, there are some failure about systemd and avahi service, when I try to print, perhaps it's the issue, but I really don't know.
journaltct -f - when I try to print a test page.
/var/logs/cups/error.log - for this day, with a debug log level, and when I added this printer and print a test page.
It tried to not use the usblp kernel module without success, the printer is not recognized by cups without this module loaded.
So, I'm quite lost with this issue.
Cupsd info:
/etc/cups/cupsd.conf
Printer info
Bus 003 Device 002: ID 04f9:0254 Brother Industries, Ltd
lsmod | grep 'usb'
usblp 13011 0
usbhid 41358 0
hid 86421 2 hid_generic,usbhid
usb_storage 43828 0
scsi_mod 130423 4 usb_storage,libata,sd_mod,sr_mod
usbcore 174164 5 usblp,uhci_hcd,usb_storage,ehci_hcd,usbhid
usb_common 955 1 usbcore
If you have any idea to help me debug this issue, I'd be grateful.
Thanks a lot to read this.
Last edited by gyan000 (2013-03-16 13:29:13)

Hi again,
Issue solved, I had to execute this commande after the package installation:
/opt/brother/Printers/dcpj315w/cupswrapper/cupswrapperdcpj315w
I contacted the package owner so he can update his package.
Thanks
Last edited by gyan000 (2013-03-16 13:29:42)

Macbook airport extreem and brother printer/scanner DCP-330C

I have macbook airport extreem and brother printer/scanner DCP-330C and everything works fine.
I can print wireless.
The only thing that irritates me is, when I start my macbook I first see a screen with MFL-ProSuite, I quit then a screen with connect with USB, I quit and then I see a small blue screen.
Is there a way to get rid of these things, so I can start directly with the things I want to do.
Thanks for the reply.
Frank

That is something that has to do with the brother software. Doesn't have anything to do with the airport base station.
I would try and Contact brother to see about disabling it.
What I think , is probably because the printer is on the airport not the computer so brothers software is getting confused.
See about deleting just the software and not the drivers. That is if you dont need the software.
Message was edited by: Edwin Silva

LUT for DCP or Rec709

Hello,
I got a job where I have to grade some RED MX footage. The output will be DPX lin 1920x1080 and it will be packed as DCP . I own a MacPro Nehalem, ATI Radeon HD 4870 and a LaCie 324 - DVI.
Can anybody help with some advice? How can I create or get a LUT to monitor the grading? Is it possible to do it with my equipement or I need to rent a different display? What options do I have? Can I grade it with a Rec709 LUT and then convert it to DCI, and how can I create or get a Rec709 LUT?
Thanks much.

Thanks for your answer. I do not have a production display and the reason I would still think of using my computer monitor is because the footage needs just some minor touches. It was graded during shooting on a TVlogic wright on the set and everything is saved in metadata. The LCD I have is very good and I would trust it in this case as long as I could load a LUT in Color that would allow me to identify roughly the path towards Rec709. Otherwise I could just buy a HP DreamColor which I assume is also very good.

Cant open dcp files on ACR 8

Hi im trying to load vsco presets dcp files on ACR 8 but the only option there is cameraraw.xmp. How would I be able to do it? Thanks in advance..

Here's my one-click boilerplate reply:
If you give complete and detailed information about your setup and the issue at hand, such as your platform (Mac or Win), exact versions of your OS, of Photoshop and of Bridge, machine specs, what troubleshooting steps you have taken so far, what error message(s) you receive, if having issues opening raw files also the exact camera make and model that generated them, etc., someone may be able to help you.
Please read this FAQ for advice on how to ask your questions correctly for quicker and better answers:
http://forums.adobe.com/thread/419981?tstart=0
Thanks!

DPX export settings for DCP creation

I have a short film that's been accepted to a major festival that requires a DCP, and I want to create the DCP professionally. I would like to provide a true 24p DPX master to the DCP company.
My final film is a 4K sequence at 23.976. I have duplicate 24 fps 5.1 audio wav stems that were output from Pro Tools, so audio isn't a concern.
Okay - so I export my sequence and choose "DPX". I'm presented with several options: 24p Full Range (max bit depth), 24p Over Range (max bit depth), 24p Standard (max bit depth), and 24p Video (max bit depth). Huh? I'm a Jack of all Trades indie filmmaker, and I can't find a word about these options anywhere - not in the Adobe manuals, not in tutorials, not even via a Google search. And, although these options are all "24p", my output still clearly shows as 23.976.
What option should I select? Why the variables? And can I simply change the frame rate to "24" under the video tab?
Finally, will I be able to import this image sequence back into a new sequence in Premiere Pro to check the 24fps audio tracks for alignment and sync?
Thank you geniuses in advance. I don't know how I would do this without you.

I just heard that DPX/Cineon was the best format to use for lossless colour grading. I also was starting to learn speedgrade, which uses DPX as it's main format. This is the first time I've attempted using any codecs specific to colour grading before. I used to export as AVI or quick time and grade that...
One of the problems i'm having is that I'm shooting on the 5D mk ii, which doesn't have anything near the colour depth of somethig like the scarlet..
I did figure out however, how to get rid of those lines. In AE down the bottom of the project tab, where the new compositions button is, there's also a colour settings button where you can change the sequence bit rate and output settings. So I got rid of the lines, but not I'm having issues with the output being over exposed in some places, and under exposed in others. But that's probably becuse of the limited colour space of DSLR's..

GTX transceiver wizard set CPLLREFCLK="101" in property/xci generate and stay for dcp ooc?

VC707 - transceivers wizard 3.5 ...
How do I with GTX transceiver wizard set CPLLREFCLK="101" so I can select my gt0_gtsouthrefclk0_in (which I'm in QUAD 113 so this is from QUAD114 correct)?
I currently have to open ..._multi_gt.vhd and the _funcsim.vhd/.v files and edit the:
SIM_CPLLREFCLK_SEL => "101",
cpllrefclksel_in => "101",
from the default "001"
The attached is my current .xci. --
I'm not sure about wizard page Line Rate,RefClk the "Transceiver Selection" I have my GTX X1Y2 from QUAD0 o ngui =QUAD113 for real set to get clk from QUAD1 per gui=QUAD114 for real REFCLK0_Q1 to my CPLL ... not sure what this does but closest thing to selecting the southrefclk0 I guess...?
I also include shared logic in example design since I think I don't want to step on my prior pcs_pma core that used include shared logic but still uses same QUAD113 - ch1 for phy.
I tried to find in .xci or report_property something to set the CPLL sel but don't see it..
currently I will set my .xci to global and delete my .dcp which will then just build from source right..
PS- when I change funcsim CPLLSEL signals it doesn't seem to simulate for them, just the "001"...?
THANKS!

Thanks, I've been looking at those diagrams for some time and just don't understand clearly. May you please point me the right direction for my application:
VC707 board, using QUAD113 the SGMII on GTXE_CHANNEL_X1Y! is already working using it's MGTREFCLK0 SGMII_CLK and now I want to get the GTXE2_CHANNEL_X1Y2 SFP+ transceiver in the same QUAD113 working using the Si5324 MGTREFCLK0 from QUAD114 as it's CPLL input.
I can't get CPLL lock. Since this Si5324 clk is from QUAD114 MGTREFCLK0 above I believed I should tie my design Si5324 clk input pin signals through an IBUFDS_GTE2 to the GTSOUTHREFCLK0 pin of my gtwizard GTXE2_CHANNEL for my SFP+ transciever. However in the design view it appears the Si5324 clk pin into QUAD 114 is mapping to GTSOUTHREFCLK1 in the diagram so I tried that as well. I've also tried to just tie it to GTREFCLK0 and/or 1, change to appropriate CPLLREFCLKSEL, and also to tie it to all the advanced clks...
Where shoudl I tie the Si5324 clk input signal -- what should my CPLLREFCLKSEL be set to.
If I understand your response it sounds like since I'm never changing clks to the SFP transceiver and only tieing one, I just leave CPLLREFCLKSEL = '001' and tie it to the GTREFCLK0?
THANKS!

How can i convert 2k resolution dpx files of a movie to DCP and will they be able to open the harddisk and view the files?

how can i convert 2k resolution dpx files of a movie to DCP and will they be able to open the harddisk and view the files?

AFAIK, this is beyond the capabilities of FCPX/Compressor. This company makes a plug-in, which I have to say I have no experience with. Here is a thread that may give you some other ideas. Good luck.
Russ

DCP 2K in After Effects and AME - everything is good, but how do I mark the DCP file as "Advertisement"?

Hello,
I need to covert a FHD video to DCP 2k. I can achieve that with After Effects and Media Encoder and export/render as DCP 2k. The problem is the cinema needs the file marked as "advertisement" to be able to run it, and by default it comes as "feature" .
I couldn't find a way in the options to change it, in media encoder or AE. Is there a way to actually change it and mark it / label it as advertisement? Or this is the only way to make DCP 2k in AE and AME?
Thank you.

I would also like to know how to use this option. (If it at all exists) Adobe team, as per my phone conversation, can you please look at this?

DCP 5.1.4

Similar Messages

Maybe you are looking for