Dead DR8-A DVD burner!

My DR8-A DVD recorder has stopped working. The drive shows itself in bios and in WinXP but I can not read or burn any CDs or DVDs.
I upgraded the firmware of the drive a while back, all according to the instructions and safety procedures provided by the MSI Live update program. I aslo have a very stable ANTECH 380 W PSU and had no stability problems during firmware flashing. The flashing completed sucessfully and the drive worked at first, but now nothing is working. I haved tried flashing again, and it completed sucessfully again but the drive is still not working.
Any help would be greatly appreciated!

If you look through these forums you will find a lot of complaint about the DR8-A.
Mine stopped doing CD's first then DVD's. It did need to be replaced. I doubt the firmware update would have done damage to kill it now if it worked at first. Sounds like it may be dead

Similar Messages

Dvd Burner Dead?

alrighty i have had this problem for quiet some time now and im hoping that someone can help me. my dvd burner (MATSHITA DVD-R UJ-845E) has been giving me some problems. it will burn cds fine from itunes and toast, but when i got to burn any kind of dvds in toast it gives me sense key errors and in idvd it just tells me that there was a problem during the burning and spits my dvd out. so what is the problem, is my dvd burner done and going to have to be sent it?

Normally this error occurs if trying to burn Commercial DVD Movies.
This problem rarely will occur when copying DATA, or IMAGE FILES burning large audio or pictures jpg. tiff. or documents.
This error normally occurs when trying to copy and burn an encrypted DVD.. If this isn't the case tell us exactly what you are trying to burn and the media you are trying to use...Don

DVD burner (UJ-825) does not recognize blank media - alignment error

Hello,
when inserting (tried several) blank DVD into my iMac DVD burner, it spits it out after a few seconds ...
error message in the logs
Jul 4 04:43:46 Bazounga kernel[0]: disk2: alignment error.
is there anyway I could re-calibrate the head of the DVD burner or is could the problem be coming from somewhere else.
N.B.: home burned DVDs cannot be read anymore (same behaviour)
When inserting a blank CD it recognises it but trying to burn a "burnable folder" is fails with error message 0x8002006E)
Finder: Write (10), block: 4294967146, count: 32 -> 3/0C/00 Medium Error, Write error
Finder: Burn failed, Wed Jul 4 05:33:38 2007
Finder: Burn sense: 3/0C/00 Medium Error, Write error
Finder: Burn error: 0x8002006E La gravure a √©chou√© √† cause d'une erreur d'√©criture sur le m√
same kind of error appeared previously with DVD's
But commercial CD's and DVD can be read after some "hesitation noise"
Is my burner dead ?

Normally this error message is caused by incorrect Format or some of the cheaper incompatible Brands of Media. I suggest you use this.
http://www.digitalfaq.com/media/dvdmedia.htm
I also suggest you use DVD-R Media.
it is the most recognized all around.
Be sure when you buy that your optical drive will burn at the speed it was designed to use.
Many of the higher speed media like 16X will not work on older computers.
They will give you error messages
Here is another good link that explains it.
http://www.videohelp.com/dvd
I suggest you find Maxell 16X DVD-R media in the individual Jewel Cases and read the packaging and you will see that it will burn at 1X,2X,4X,8X,and 16X this media will work with just about anything in the way of computers.
Don

Best hd DVD burner software

Which is the best third party software to purchase for my new iMac so I can make hd DVDs from iMovies. I didn't realise my iMac didn't come with a DVD burner app. thanks

Why is there no iDVD on my new Mac?
Apple insists that the entire world has access to fast broadband (and are prepared to pay for the considerable bandwidth usage) and wants to distribute home movies to friends and relatives via download (iCloud, YouTube, Facebook, whatever) rather than mailing them a DVD. The fact that in reality not all users do, has so far had no effect on this policy. If you scream and shout loudly enough down the phone Apple may send you a free copy of iDVD. Stating that they would return their brand new Mac unless they received a copy of iDVD worked for some, but that is now said to have been withdrawn by Apple.
Also, you can complain bitterly via Apple’s Feedback link, perhaps suggesting that Apple could have provided a choice between burning DVDs and distributing home movies by other means. You may feel that Apple should not dictate how you destribute family videos or photos to distant relatives and friends, and should not assume that every user is prepared to pay for the excessive bandwidth usage charged by ISPs for huge downloads from the App Store:
http://www.apple.com/feedback/
Whilst Macs with a Superdrive continue to be able to burn video DVDs, the software for so doing, iDVD, is no longer included in the iLife bundle that came with OS 10.7 Lion (which also omitted iWeb) or that comes with OS 10.8 Mountain Lion. And it is no longer included in the iLife 11 from the online Apple Store: http://www.apple.com/ilife/. Your only solution is to look on Amazon or eBay and try to get an older version that includes iDVD 7, i.e. iLife version 9 onwards. You should also do this if you plan to buy a new Mac anytime soon, as stocks of iLife that include iDVD will not be available for ever.
However, the vastly more expensive FCPX can burn a DVD without iDVD or DVD Studio Pro involvement, but lack the themes etc of iDVD. Also, of course, there is Roxio Toast, which is the best software for burning anything but again does not offer the flexibility of iDVD.
Apple has clearly indicated in the newest Mac mini and Retina Display MacBook Pro that it plans to get rid of optical disc drives as soon as possible across the board, providing an external USB drive as an option for users who need one.
Users increasingly have fewer opportunities to use optical drives, as the bulk of third party software is now available as a digital download either directly from the vendor or through Apple's App Store. Apple also sees digital distribution as the future of music and movies, as exemplified in Apple TV, which has never included an optical drive.
The company has never supported any new HD optical disc formats on its products, including Microsoft's ill fated HD-DVD or Sony's Blu-ray format, despite initially being involved in the Blu-ray standardization process. Instead, Apple has put its resources behind developing increasingly higher definition audio and video formats that it can distribute electronically through its own iTunes Store.
And if you think Microsoft are any better, their new Windows 8 operating system will not play DVDs, or burn them, unless customers buy an extra upgrade, the company has announced: http://www.gizmag.com/windows-8-no-dvd-playback/22443/
In other words, computer manufacturers have declared optical media as dead, long before consumers are ready to stop using them, which is fine as long as they offered us a choice, but they won’t even do that. Flexibility and intuitive use of a computer seems to be a thing of the past.

External DVD burner - USB or Firewire?

when I got my first OS X system - about six years ago - I bought a firewire DVD burner. it worked great for all this time and finally died a few months ago.
time to get a new one! But I am having a hard time finding an external firewire Drive - all I see is USB.
can someone recommend a good FW 1394 external DVD / CD burner drive somewhere
or...
can someone assure me that USB is now so terrific that I don't need firewire and will be very happy with a new state of the art USB 2.0 drive?
thanks!
willfriedwal;d

Be careful with Other World. They sell DVD burners in two different types of enclosures. The info at the top of the burner page says Oxford 911 chipsets, but the Mercury Value DVD burner they sell for $71.99 uses a different set - the Prolific 3507 set. Google that name and see how many angry people you find. I bought one after being told by a salesman that the only difference between the Mercury Value and the Mercury Pro was cosmetic. Wrong. The Value drive wouldn't mount a disk when plugged into the firewire port on my 20" G5 iMac. It did mount when plugged into the USB port, but my understanding is that you can't boot from a CD in a USB drive (not easily anyway), and you can in Firewire. My internal drive is dead in the water, and estimates I got to replace it were $250 or so, so I'm going external. Gonna buy the Mercury Value Pro with Oxford 911 now that I got my money back (no easy task either, but I finally got it.)
Just thought I'd pass that along.
brotone

Creating a new library from a DVD Burn library

I have my entire library of photos on my iMac in iPhoto 6.0.6. I recently spent quite a bit of time cleaning up what had been a rather messy, unorganized, photo library. My organizational method consisted of consolidating old film rolls which were inherited from original imports that were in different folders by moving groups of photos into single "film rolls" for older years and making fewer rolls for the last few years. I then went back through and corrected photo dates for a bunch of images that were scanned in, etc. I downloaded Keyword Manager, which I like a lot, and applied keywords to every photo in my collection. I also deleted a bunch of old photos which were too similar to better shots or simply not worth keeping. Once I finished all of this I had my new library consisting of 1892 pictures, which I hoped to backup and allow to serve as a "gold master copy" of all of my photos to date. In browsing the database in Finder, I noted that there were a lot of images in the "Original" folders that were not in the library. Some of these were images I had deleted in the library. (I know better than to do anything through the finder other than browse. I know that to maintain integrity of the library it is necessary to only perform actions through iPhoto.) I did a database rebuild and asked iPhoto to recover orphaned files which did nothing. I really wanted this database to be in pristine condition since I was using it as my master copy, but could not figure out how to do away with old unwanted images in the "originals" folders. I went ahead and created a DVD library with "Share -> Burn", and voila, the new iPhoto Library that was created on the DVD appeared to be "clean" with only the 1892 pictures in my viewable library existing in the Originals folder. OK, so far so good. I then took the DVD I had burned and attempted to replicate my library on my iBook which had a clean install of iLife '06 on it. When I launched iPhoto with the DVD in place it showed me an empty hard drive library and the burned library from the DVD. At first I attempted to just copy individual Film Rolls from the DVD to the local library. While this worked in bring the images over, the keywords became all jumbled. The resulting photos would have keywords attached which did not belong to them and were different from what was on the DVD. I then deleted the iBook library and tried copying the entire iPhoto Library folder from the DVD to the iBook via the Finder. When I relaunched iPhoto, presto all the photos were in my local library with keywords, film rolls and other metadata intact. However in browsing the library I came across a few photos which would cause iPhoto to crash when I tried to edit them. This was a consistent behavior on specific images. Reading through the forums I came across the color profile bug and through testing verified that this was not the problem. Meanwhile back on the iMac I could edit the photos in question with no problem. I verified that the image had not been corrupted during the DVD burn as well. The files are identical between the iMac and the iBook. I know this is a long drawn out post, but if anybody has read this far, here are my questions ...
1) What is the best way to go about creating a "clean" database with internal integrity after a doing a lot of edits and metadata changes? Shouldn't the burn to DVD do what I want?
2) How come when I copied subsets of my library over to a new machine from the DVD, the keywords seemed to get all jumbled? Is it a matter of indexing them? If I added all the keywords to an empty library before copying the images over, would it work? Is there not a way to just copy portions of a DVD library into another library?
3) Any ideas on the crash while attempting to edit problem? The image will load as a thumbnail, and then briefly flas the full size image, before iPhoto crashes and pops up a dialog asking if I want to restart it.
Thanks for staying with me!
Mark

Problems solved with iPhoto Manager's rebuild function! Thanks to Brian Webster of Fat Cat Software. Great program!
Mark

I just bought a new mac mini and an external DVD burner. I want to burn a DVD video and it will not play on the TV but only on the computer? Need this figured out for tomorrow.

I just bought a new mac mini and an external DVD burner. I want to burn a DVD video and it will not play on the TV but only on the computer? Need this figured out for tomorrow. Can anyone help me?

Congratulations on the new Mini. Are you saying you tried burning and it does not play, or do you want to burn it only for the computer to be able to play it?
OS X Mountain Lion: Burn a CD or DVD may help.

DVD Burn problem. "Device error - the target device isn't suitable for use"

Hello everyone,
I initially had a lot of problems with PE8. However the nVidia driver update solved most of them.
Just thought it was important to report success as well as failure!
However one problem remains. I get the following error at the 96% mark while burning. "Device error - the target device isn't suitable for use". It is always at the 96% mark and the program is "compiling [something]" when this happens.
Having searched this site I notice that user rgferg posted a similar problem 13 days ago but was redirected to repost in a different place, but never did.
I have tried to burn a 1hr clip 4 times and every time I have selected the slower burn speed (8MB/s) as has been suggested. It seems that inferior media is a culprit, so I have bought some [quality] Verbatim DVD-R media to try in my Phillips SATA optical drive. I am sceptical this will work, but open minded nonetheless. I will give it a whirl when my computer has stopped capturing the VHS I am working on.
Each time the burn failed the disk was automatically ejected and the burn process had actually started and progressed perhaps ~40% or so.
This indicates to me that it is a drive sharing issue, rather than a media issue. Somewhere on this forum it suggests that I go through a 20+ step process and delete/disable every piece of software that can compete with Premiere among other things. IF I do this what do I burn with outside of Adobe? Do I have to get imgburn or whatever it was called? What if I like Nero? Nero 6 has worked great for me for 3 years.
So given I am willing to uninstall my old optical drive burning software, who out there can recommened commercial software that for them creates a painless Adobe burning experience with no errors or conflicts? Perhaps there is another solution that I did not see on this forum?
I am running Windows XP SP3. I have the latest nVidia drivers for my SLI GeForce 7600 GS cards. I have 3 monitors. RAID 0 SATA, 2GB RAM, Athlon X2 5400.
Justin.

OK been working through the list of 20 things Adobe recommends to fix DVD burn error. No luck yet:
system meets minimum requirements
Project size does not exceed disk capacity
successfully burned project to DVD folder -thus skip to step 8.
8. Using new blank media for burning
9. Try different media and DVD burners. Bought Verbatim DVD-R. Don't have another DVD burner. Adobe's supported burner list is VERY short, so of course mine is not on it.
10. Uninstalled Nero 6. Did NOT uninstall Acronis True Image workstation or Lightscribe. These do not access the drive unless I say so!
11. Have not yet disabled startup items and services. This will take a lot of work and will leave to last. Deactivated Spybot thus far.....
12. Disabled IMAPI CD burning COM
13. DMA if available already set. Haven't set this in BIOS yet. I already think it is, but will check next boot.
14. Updated DVD firmware
15. Already updated nVidia drivers
16. Don't have any other DVD drives to disconnect.
17. MPEG workaround. Will resort to if required.
18. Disable Autoplay? XP only has "prompt me each time to choose an action". I have set this for ALL file types.
19. Have NOT refreshed the DVD drivers in the registry. This step involves uninstalling PE8. Will leave this as last resort.
20. Visit forums to see if other have the same problem. Hi guys
So still working through some of the items above.
Can anyone direct me to advice on how to write the encoded files sent to the hard drive, or the VOB files that PE8 failed to burn to a disk? Will the former work with DVD menus?
What a process.
Stay tuned.
Justin.

Problems ripping with an external DVD Burner

Hello Everyone,
Recently I purchased a Liteon External DVD Burner off of newegg (http://www.newegg.com/Product/Product.asp?Item=N82E16827106011) -- It's a Liteon SHW-1635SX -- I bought this because the DVD-ROM drive thats in my tower natively is REALLY slow and I wanted to get a new one that I could use with a laptop that I`m going to purchase in the future. Whenever I try to rip a CD into iTunes using the burner, It says that it's ripping the disk, however it doesn't spin up the cd and it takes about 2 seconds to "rip" all the songs. I know this drive is soposed to be faster than my old one, But two seconds is a little TOO fast. Plus, I know that it's not copying the songs because when I try to listen to them in my library, the song won't play. (Under time it says "789:54..." for all the songs on the cd, in my library) However, the burner rips perfectly in Windows Media Player... Is this perhaps some kind of glitch with iTunes??? Basicly, the only way I can rip a CD into iTunes is to use my old DVDROM drive, but that defeats the purpose... below is the CD Diagnostic log that I got from iTunes::::::::
Microsoft Windows XP Home Edition Service Pack 2 (Build 2600)
HP Pavilion 05 P9859A-ABA 533w
iTunes 6.0.4.2
CD Driver 2.0.4.3
CD Driver DLL 2.0.3.2
LowerFilters: PxHelp20 (2.0.0.0), AFS2K (3.1.21.0), DRVMCDB (1.0.0.1), SSCDBHK5 (1.0.0.1), PFC (2.5.0.196),
UpperFilters: GEARAspiWDM (2.0.4.3),
Video Driver: Intel(R) 82845G/GL Graphics Controller\Intel(R) 82845G/GL Graphics Controller
IDE\DiskMaxtor4R060J0_________________________RAMB1TU0, Bus Type ATA, Bus Address [0,0]
IDE\DiskST34323A_______________________________3.02___, Bus Type ATA, Bus Address [1,0]
IDE\CdRomCOMBIRW16x10/DVD_______________________H1.0___, Bus Type ATA, Bus Address [0,0]
USBSTOR\CdRomLITE-ONDVDRW_SHW-1635SYS0Y, Bus Type USB
If you have multiple drives on the same IDE or SCSI bus, these drives may interfere with each other.
Some computers need an update to the ATA or IDE bus driver, or Intel chipset. If iTunes has problems recognizing CDs or hanging or crashing while importing or burning CDs, check the support site for the manufacturer of your computer or motherboard.
Check the Windows Update website to verify that you have the latest service packs and patches for your OS. Service packs affect the performance of USB and firewire CD / DVD drives.
Current user is administrator.
E: COMBI RW16x10/DVD, Rev H1.0
Drive is empty.
F: LITE-ON DVDRW SHW-1635S, Rev YS0Y
Audio CD in drive.
Found 9 songs on CD, playing time 42:13 on Audio CD.
Track 1, start time 00:02:00
Track 2, start time 03:30:07
Track 3, start time 08:44:33
Track 4, start time 12:03:74
Track 5, start time 17:55:53
Track 6, start time 22:14:31
Track 7, start time 25:32:60
Track 8, start time 30:13:01
Track 9, start time 35:59:06
Audio CD reading succeeded.
Get drive speed succeeded.
The drive CDR speeds are: 8 16 24 32 40 48.
The drive CDRW speeds are: 8.
The drive DVDR speeds are: 8.
The drive DVDRW speeds are: 8.
The last failed audio CD burn had error code -128(0xffffff80). It happened on drive E: COMBI RW16x10/DVD on -128(0xffffff80) media at speed 0X.
Your replies are greatly appretiated!
--Aric--

hi Aric!
hmmm. we'd better check on the usual suspects with that. (the incredibly long song times can also be associated with these sorts of causes.)
You can't import or play music from an audio CD in iTunes for Windows
... and the following resources might be helpful with that. (check on firmware and drivers even though it's a brand new unit.)
Using CD Diagnostics in iTunes for Windows to troubleshoot CD/DVD drive issues
iTunes for Windows: Updating the firmware on your CD or DVD drive
Updating the drivers on your Windows PC
Where to find firmware for your CD/DVD drive
love, b

My DVD burning problems solved....here's what I did.

Like some of you, I was having MAJOR problems burning DVDs. My initial setup was a dual 2.0 ghz G5 purchased in July of last year, so it came with a 8x burner and iLife '04 (iMovie 4.0.1 and iDVD 4.0.1). Seeing as how I have 1.5gigs RAM and a fairly new system running 10.4.3, I didn't think I was going to have any problems burning DVDs....
HA.
Nothing worked right......a 1-hour long project burned for more than 8 hours without finishing, or iDVD would quit for no reason, or the burn would fail. I noticed that Terminal said that during these burns it was only burning at 4x even though 47x was requested. Chapters were not working. Applecare was not helpful, only suggesting that I try to burn under a new user, and then call them back. That didn't work either.
I probably took the lazy man's way out, but I decided this waste of time was unacceptable. I went out and purchased a 16x SuperDrive Pioneer DVR-110D replacement from MCE for $92, and upgraded to iLife '05 for another $79. I installed the drive myself (VERY easy with the included instructions), and tried the new setup under a newly created user.....
PERFECT burning every time. Not only that, but Terminal showed a requested burn speed of 16x and a burn speed of 16x. A two-hour project is now burning in less than 8 minutes. Multiplexing still takes time, but it's less than 1 hour!
On an interesting side note: when I try to burn under my regular user name, I STILL get an burning error (says image not complete, or incomplete....something like that). But under the user name created just for burning I have no problems. The chapter problem was solved when I stopped putting a chapter marker at the very beginning of my iMovie projects, since iDVD automatically puts one in called "Beginning," which you can change to anything you want.
Maybe this will help others.....
Dual 2Ghz G5 Mac OS X (10.4.3) 1.5 gigs RAM, iMovie 5.0.1, iDVD 5.0.1

it was only burning at 4x even though 47x was requested.
That's a issue discussed in the past.
It turns out that 8X DVD burning means about 47X CD burning - you were requesting 8X DVD but only got 4X DVD burning.
I haven't seen it discussed anymore so maybe Apple got around to eliminating that 'quirk' in terminology.
I suspect some of the early 8x DVD burners didn't perform as advertised. I'm glad your new 16X burner is working for you.

ITunes Seem to Have Suddenly Stopped Communicating With the CD/DVD Burner

Hello, I wonder if anybody can help - my itunes application seems to have suddenly stopped communicating with my laptop's cd/dvd burner
(Generic Name (E: H - T-S D D A S - 20N ATA Device)).
About 2 years ago, I have experienced a similar problem, but was able to resolve it by downloading 64-bit compatible GEAR drivers to my system. However, the problem has re-appeared when I have updated to iTunes Version 10.1. Funny enough, the cd/dvd burner started getting recognized again when I updated to iTunes Version 10.2, but halfway through me burning a large playlist to multiple cds has suddenly stopped recognizing the cd/dvd burner again, and has never "resolved itself" ever since.
I have tried multiple approaches to solving this issue, including completely re-installing itunes software and completely re-installing GEAR drivers, but nothing works. I have even tried uninstalling GEAR drivers completely, as I read that it worked for someone on one of the similar forums, but that didn't work either.
My itunes diagnostics runs all the points of the cd/dvd drive check successfully, except for the last point (Can Not Read Audio CD). Here's what the diagnostics summary looks like:
Microsoft Windows Vista x64 x64 Home Premium Edition Service Pack 2 (Build 6002)
Hewlett-Packard HP Pavilion dv9700 Notebook PC
iTunes 10.2.1.1
QuickTime 7.6.9
FairPlay 1.11.16
Apple Application Support 1.5
iPod Updater Library 10.0d2
CD Driver 2.2.0.1
CD Driver DLL 2.1.1.1
Apple Mobile Device 3.4.0.25
Apple Mobile Device Driver not found.
Bonjour 2.0.4.0 (214.3)
Gracenote SDK 1.8.2.457
Gracenote MusicID 1.8.2.89
Gracenote Submit 1.8.2.123
Gracenote DSP 1.8.2.34
iTunes Serial Number 0016AB580A7B0C28
Current user is not an administrator.
The current local date and time is 2011-04-14 17:52:25.
iTunes is not running in safe mode.
WebKit accelerated compositing is enabled.
HDCP is not supported.
Core Media is supported.
Video Display Information
NVIDIA, NVIDIA GeForce 7150M / nForce 630M
** External Plug-ins Information **
No external plug-ins installed.
The drive F: Motorola MB810 Rev 0001 is a USB 2 device.
iPodService 10.2.1.1 (x64) is currently running.
iTunesHelper 10.2.1.1 is currently running.
Apple Mobile Device service 3.3.0.0 is currently running.
** CD/DVD Drive Tests **
No drivers in LowerFilters.
UpperFilters: GEARAspiWDM (2.2.0.1),
E: H-T-S DDA
S_-20N, Rev W_05
Audio CD in drive.
Found 1 songs on CD, playing time 255:08 on Audio CD.
Track 1, start time 00:02:00
Audio CD reading failed. Error Code: 27 27 27 27 27 27 27 27 27 27 27 27 27 27 27 27 0 0 0 0.
iTunes cannot play or import music from a CD in this drive. The drive may need a firmware update. Check with the manufacturer.
Get drive speed succeeded.
The drive CDR speeds are: 3 9 16 24.
The drive CDRW speeds are: 3.
The drive DVDR speeds are: 3.
The drive DVDRW speeds are: 3.
Error Correction is turned on for importing audio CDs.
I have noticed that the diagnostics summary containes a suggestion to update firmware of my laptop's cd/dvd drive, but currently there are no such firmware updates available.
Another frustrating issue that I ran into was trying to convey this issue to Apple Technical Support via e-mail using the Express Lane for the troubleshooting issues. I really fail to understand why I am being asked for the "hardware serial number" when I'm clearly choosing the categories for "iTunes/CD-DVD Import Issues" which are software, not hardware, categories! This prevents me from being able to simply send the description of my problem to the correct Apple Support department, and does not let me do that even when I enter my itunes' Serial Number, which can be found in the diagnostics summary provided above.
Much Thanks to anyone who can provide any kind of helpful advice, even if it's just on how to be able to convey this problem to Apple Support via e-mail!

Okay ... checking something else:
Current user is not an administrator
Is that true? Or do you in fact have a Windows user account with full administrative rights?
(It's possible that a permission may have gone astray in your usual user account, which might be causing the burning issues.)

Possible to install HD-DVD Burner in iMac G4?

Hi, I was wondering if it is at all possible to install HD-DVD burner in a iMac G4? Anyone tried this?

I know that Toast Titanium 8 for Mac supports Blu-Ray burning (Apple's loyalties are in the Blu-Ray not the HD DVD camp) but the G4 is not a processor I'd ever want to be encoding HD in. The G4 wouldn't even be up to playing discs. So I think you could do it with a Blu-Ray drive but you shouldn't do it. I hate having to wait whilst an SD DVD encodes HD is at least four times longer. Remember Apple hasn't put a HD spec burner in even it's 8-core Mac Pro yet!
mrtotes

Looking for a external blu ray dvd burner for my mac

looking for a external blu ray dvd burner for my mac

There are plenty of options but I have found that the LaCie d2 http://blu-ray.burnworld.com/burners/lacie-d2.htm works more consistantly. I use Toast 11 mainly for Blu-Ray. The drive does come with a basic verison of the software which is good for most but you need to upgrade to do some serious authoring.

DVD burn error message

I get this error message when I try to burn a data DVD: "Burning the disk failed because communication to the disk drive failed. (error code 0 x 80020022)
I am attempting to use the original drive system (Pioneer DVD-RW DVR 104) and it plays CD's and DVD's without a problem. Thoughts? Jim

just had this problem with a 17" MacPro purchased in Jan 09. Toast Titanium 9 had no problems burning the CD. tried it again in Finder but backed the burn speed down from 24x to 8x - no problem.
I can only assume it is cheap media causing the problem - we have no problems with Maxell CDs at full burn speed (24x). The CDs causing the problems are Verbatims (rated at 1-52x) that have printable surfaces.
hope this helps

G5 DVD burner error message? Help please?

I get this error message when I try burning a 1gb quicktime movie to dvd on my pre installed standard burner. Thanks in advance
the link below is a screenshot of the error
http://www.darkstargraphics.com/dvd_message.gif
Im at a loss and ready to by another
below is the dvd burner profile
PIONEER DVD-RW DVR-106D:
Firmware Revision: A606
Interconnect: ATAPI
Burn Support: Yes (Apple Shipped/Supported)
Cache: 2000 KB
Reads DVD: Yes
CD-Write: -R, -RW
DVD-Write: -R, -RW, +R, +RW
Burn Underrun Protection CD: Yes
Burn Underrun Protection DVD: Yes
Write Strategies: CD-TAO, CD-SAO, CD-Raw, DVD-DAO
Media: No

The error "internal target failure" appears on PCs using this drive as well, so it appears that it's not a Toast specific error.
However, in my browsing, no one seemed to be able to tell if it was a true hardware failure of the drive, or if it was caused by poor quality media.
I'd try other brands of media and a lens cleaner before flashing the firmware. And, if you do decide to flash the firmware, the current, official firmware for that drive is here. The link in MLCinma's post contains hacked (region free) firmware and is outdated in any event.
Let us know what brand of media you're using and what speed you're burning at.
The DVR-106D has had lots of reports of failures, so it could very well be the drive. At least a replacement DVR-111D will only cost you about $40 - $50.

Dead DR8-A DVD burner!

Similar Messages

Maybe you are looking for