Dead Sat Pro A30 - it won't even reach BIOS
Hi,
got a Sat Pro A30 which has suddenly refused to do anything - if I hit the power button, the lights on the front of the case light up briefly (for perhaps half a second), then there's a quiet 'click' and all goes quiet again. I've tried it with & without the battery present, and with and without mains attached. The mains cable seems to be OK, since when connected to the notebook it indicates that the battery is charging.
Any ideas?
Hi
There must be something wrong with the hardware. Maybe the motherboard fault.
Unfortunately, I dont think that you can solve it by yourself.
In my opinion the only way to solve it is to contact the ASP. The Toshiba service can run some diagnostic test to find out whats wrong.
Similar Messages
-
What AC adapter do I need for the Sat Pro A30?
What AC adapter do i need for the Satellite pro A30, it will not charge and as it has a loose connection on the plug.
Hi,
in the specs I found this:
up to CPU 2.8GHz PA3165U/E-1ACA Autosensing AC Adaptor - 0.52kg - 90W - 100~240V 50/60Hz (Universal) - DC 19V 4.74A -- over 2.8GHz PA3290U 120W
Bye -
Z68A-GD65 (B3) won't even enter bios
Well I got my MSI z68A-GD65 (B3) today.
The first time I set up the system I forgot to plug in the 8pin because I got confused with the (20 + 4)PIN stuff (I haven't had a PC for some years). After I sorted that out I got the system to start, it told me that "hardware and cpu had changed F1, F2 bla bla; so I pressed F1 to enter setup and have a look but it didn't do anything so I had to restart.
Right now I can only start the system, I will get somthing about marvell, and "no hard disk detected" (there is one plugged in without any windows), it will continue afterwards at the bottom there will appear DEL for Setup and F11 for bootmenu but neither of them will work.
So now I'm sitting here in front of my new computer I need to do some urgent work :S, but there is no way even to get to the setup.
I've tried to change the ram sticks (only one, with two,etc...) I've cleared the CMOS a thousand times, there is no way.
Do you have any clue of what to do?
My setup right now is
z68A-GD65 (B3)
i7 2600k
Corsair Vengeance 1600mhz 4x4=16gb 9-9-9-24 1.50V ver2.12Quote
If I put the CPU in a bad way, would the thing actually start?
Not impossible. We have seen many a case of slightly bent socket pins, and then the pin does not make proper contact, which can have a myriad of side effects.
Take the CPU off, use a camera with macro facility if you got one, and take a high res picture to inspect the imprints on the CPU pads. A magnifying glass and bright light will also do.
Inspect the socket pins for any anomalies. -
Satellite Pro A30: CD/DVD drive not working - How to restore OS?
I want to run the recovery discs to restore my laptop to original condition but the cd/dvd rom is not working.
Does any one have an idea how I can do this either by connecting my laptop to another pc or is there a programme on the web I can access to do this for me.
Bacically even after running CCleaner and other programmes the laptop is still running slow and struggling.Hi mate
Im not quite sure if the old Sat Pro A30 is able to boot from USB drive. In such case you could try to install the OS from USB flash stick.
Here is a interesting posting about this theme:
http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=63986 -
My Mac Book Pro was really slow at everything and would kick me out of my photos every time i got on them. now it won't even allow me to log on. i put my password in and the screen will flash white and go back to the login page. HELP please...
There is nothing wrong with your Dell, it will work fine with any MacbookPro. I have been using Dell displays for over 12 years with many different Mac models. I have two 21" Ultra Sharp displays working side by side to design a Keynote presentation right now.
The issue your having is with the way Keynote takes control of the video output to both displays, it sends the presentation signal to one and the presenter display to the other, this is set up in;
Keynote preferences > Presenter display.
If you want to show a wesite or another app on either display, use application switcher:
press the the command key on the keyboard, then the tab key; a row of applications will show what applications are running, choose which one you want to show. Use command > tab to return to Keynote. -
I updated my Macbook Pro last week to Lion. I went to go import pictures from a memory card to my iPhoto, but only a portion of them loaded before my iPhoto froze and I had to Force Quit it. Now iPhoto won't even open... Help!
Please! I need an answer fast!!!!Option 1
Back Up and try rebuild the library: hold down the command and option (or alt) keys while launching iPhoto. Use the resulting dialogue to rebuild. Choose to Rebuild iPhoto Library Database from automatic backup.
If that fails:
Option 2
Download iPhoto Library Manager and use its rebuild function. This will create a new library based on data in the albumdata.xml file. Not everything will be brought over - no slideshows, books or calendars, for instance - but it should get all your albums and keywords back.
Because this process creates an entirely new library and leaves your old one untouched, it is non-destructive, and if you're not happy with the results you can simply return to your old one. .
Regards
TD -
After a year of owning my macbook pro late 2012 retina model, it started having difficulty charging, it wouldn't charge even when green on the magsafe, and had difficulty turning orange, basically right after the 1 year warranty was over by one month, I went into the apple store and they told me that I simply needed to replace the power adapter and cord and it would be fine, but that it most likely was caused by me plugging it into a power strip, and that I had to plug it directly into the wall in its own power slot, which they never said that was what you were supposed to do when I purchased the laptop and could not find it anywhere in the literature. It was fine in the store for the apple worker, but after even just a few months I had to to constantly twist and unplug and replug the magsafe adapter from different angles just to get it to work, and it was like a living ****, as I am a digital artist and my wacom tablet will not work until my macbook pro is charging and the magsafe is orange, so everyday I would waste 30 minutes to an hour with the finicky magsafe, until recently my macbook pro will not turn on at all.
Since the problem arose after warranty I had to pay out of pocket for the replacement magesafe cord, which was a temporary solution, I pointed out that the magsafe power port on the laptop itself also had burn marks just like the magsafe cord that had a few pins pushed in and was slightly blackened but the attendant ignored that and said it was fine and just swapped out the cord. The "genius" attendant claimed if I just plugged in the macbook pro directly into the wall, everything would be fine and back to normal, and I did just that, I never plugged it into a power strip ever again, and still we arrive to my current predicament.
I believe I have to repair the actual power port the magsafe plugs into on the laptop, and get a new magsafe cord all over again, but it will be much more expensive than simply swapping out a cord this time, and I don't think the reason this happened to begin with has been truly identified, and I'm worried I have to make this repair every year, and I can't afford this kind of planned obsolescence, and I thought I was getting the best laptop in the world, and it was, everything was perfect not one single problem, except for this power issue, which now won't even allow me to use the computer at all and is now a giant paper weight, and leaves a dirty taste in my mouth when it comes to apple products.
I live in San Francisco in a house that was built around 1910 and don't know much about what or when renovations were made for power, but I have a feeling some kind of incorrect voltage is happening, and I was never instructed on this, and every other macbook is fine, my roommates have earlier models like the 2007 and 2009 MacBooks and have no problem like mine.
Please help meI don't understand why and how the red light in the audio jack is still on while the computer is totally off, not connected to any power source and the battery seems to be empty... how is taht possible?
Because the battery is not empty, something is messed up, likley the SMC.
All I can advise is doing a SMC Reset, which resets the power firmware in case it got messed up and hopefully that will charge the battery up like normal.
If you can't do it or it doesn't work tommorow after charging up (turned off) overnight then just take it to Apple.
https://support.apple.com/kb/ht3964 -
My macbook pro keyboard backlight won't turn off, even after pressing F5
my macbook pro keyboard backlight won't turn off, even after pressing F5
Try resetting the SMC http://support.apple.com/kb/ht3964
-
I just had 2 MacBook pro's stop working completely. No previous issues. Won't even turn on when plugged in. Any ideas?
See if a SMC reset will breath life into them:
https://support.apple.com/en-us/HT201295
If not, make an appointment at an Apple store genius bar for a FREE evaluation. Warranty status is irrelevant.
Ciao. -
MacBook Pro running updates won't startup, even in Safe Mode
I ran some software updates on my MacBook Pro running Lion and when it restarts it has a striped screen and says 'You need to restart your computer.' It won't even allow me to restart in Safe Mode. Any ideas?
Install or Reinstall Mavericks or Mountain Lion from Scratch
Be sure you backup your files to an external drive or second internal drive because the following procedure will remove everything from the hard drive.
OS X Mavericks- Erase and reinstall OS X
OS X Mountain Lion- Erase and reinstall OS X
OS X Lion- Erase and reinstall Mac OS X
Note: You will need an active Internet connection. I suggest using Ethernet if possible
because it is three times faster than wireless. -
I have a new mac pro 'can', and was checking settings. I gave a user who I didn't recognize 'no access', and lost all access to my computer immediately. Tried to change access back, but I was totally locked out (even as the admin). It won't even reboot! I thought it might have been back when I gave Adobe access (when they had their Cloud fiasco and my machine kept crashing with Premiere). Can anyone suggest anything?
MacPro 2013, 6-Core, 3.5 Ghz, 32 gigs of Ram, latestt update for Maverick
Thanks!Reset the SMC and PRAM
Intel-based Macs: Resetting the System Management Controller (SMC)
About NVRAM and PRAM
If you purchased it within 90 days yo have free telephone support from Apple
Complimentary Support (USA)
- Make an appointment at the Genius Bar of an Apple store.
Apple Retail Store - Genius Bar -
I attempted to update OS X 10.8.5 today and it seems to be stuck. It won't even let me restart. I have a MacBook Pro. Can someone help?
Hold down the Power button for 5-10 seconds until the computer shuts down. Restart. Report what state the computer is in at that time.
-
My mid-2012 MacBook Pro has the fan constantly running. As soon as I turn it on. My MBP won't even be hot and the fan is running. How can I fix this?
If you are still under warranty and/or have AppleCare, call them. Let them deal w/it.
OOW try the following: http://support.apple.com/kb/HT1411 Apple Portables: Resetting the System Management Controller (SMC) -
Installed a ATI Radeon HD 5770, now Final Cut Pro won't even open - says 0mb Vram?
Installed a ATI Radeon HD 5770, now Final Cut Pro won't even open - says 0mb Vram? Only dvi port work the two mini's not at all. Bad card? Macpro 3,1
I would guess there is a a corrupt media in the project. You could also try to copy a part of it to new project which is shorter and see what happens. 5 Hours is extremely long. Best to divide it to smaller sections.
-
My Macbook Pro is about 4 to 5 years old. I've noticed the last few months that speed was becoming much slower. It slowed to a crawl last week and won't even turn on now. Where can I take my Macbook Pro for service near Jackson, Michigan?.
Things You Can Do To Keep Your Computer From Slowing Down
If your computer seems to be running slower here are some things you can do:
Boot into Safe Mode then repair your hard drive and permissions:
Repair the Hard Drive and Permissions Pre-Lion
Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
Repair the Hard Drive - Lion
Boot from your Lion Recovery HD. When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported, then click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu. Select Restart from the Apple menu.
Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Restart your computer normally and see if this has helped any. Next do some maintenance:
Suggestions for OS X Maintenance
For situations Disk Utility cannot handle the best third-party utility is Disk Warrior; DW only fixes problems with the disk directory, but most disk problems are caused by directory corruption; Disk Warrior 4.x is now Intel Mac compatible.
OS X performs certain maintenance functions that are scheduled to occur on a daily, weekly, or monthly period. The maintenance scripts run in the early AM only if the computer is turned on 24/7 (no sleep.) If this isn't the case, then an excellent solution is to download and install a shareware utility such as Macaroni, JAW PseudoAnacron, or Anacron that will automate the maintenance activity regardless of whether the computer is turned off or asleep. Dependence upon third-party utilities to run the periodic maintenance scripts was significantly reduced since Tiger. These utilities have limited or no functionality with Snow Leopard or Lion and should not be installed.
OS X automatically defragments files less than 20 MBs in size, so unless you have a disk full of very large files there's little need for defragmenting the hard drive. As for virus protection there are few if any such animals affecting OS X. You can protect the computer easily using the freeware Open Source virus protection software ClamXAV. Personally I would avoid most commercial anti-virus software because of their potential for causing problems. For more about malware see Macintosh Virus Guide.
I would also recommend downloading a utility such as TinkerTool System, OnyX 2.4.3, or Cocktail 5.1.1 that you can use for periodic maintenance such as removing old log files and archives, clearing caches, etc.
For emergency repairs install the freeware utility Applejack. If you cannot start up in OS X, you may be able to start in single-user mode from which you can run Applejack to do a whole set of repair and maintenance routines from the command line. Note that AppleJack 1.5 is required for Leopard. AppleJack 1.6 is compatible with Snow Leopard. There is no confirmation that this version also works with Lion.
When you install any new system software or updates be sure to repair the hard drive and permissions beforehand.
Get an external Firewire drive at least equal in size to the internal hard drive and make (and maintain) a bootable clone/backup. You can make a bootable clone using the Restore option of Disk Utility. You can also make and maintain clones with good backup software. My personal recommendations are (order is not significant):
1. Carbon Copy Cloner
2. Data Backup
3. Deja Vu
4. SuperDuper!
5. SyncTwoFolders
6. Synk Pro
7. Synk Standard
8. Tri-Backup
Visit The XLab FAQs and read the FAQs on maintenance, optimization, virus protection, and backup and restore.
Additional suggestions will be found in Mac maintenance Quick Assist.
Referenced software can be found at CNet Downloads or MacUpdate.
Additional Hints
Be sure you have an adequate amount of RAM installed for the number of applications you run concurrently. Be sure you leave a minimum of 10% of the hard drive's capacity as free space.
Add more RAM. If your computer has less than 2 GBs of RAM and you are using OS X Leopard or later, then you can do with more RAM. Snow Leopard and Lion work much better with 4 GBs of RAM than their system minimums. The more concurrent applications you tend to use the more RAM you should have.
Always maintain at least 15 GBs or 10% of your hard drive's capacity as free space, whichever is greater. OS X is frequently accessing your hard drive, so providing adequate free space will keep things from slowing down.
Check for applications that may be hogging the CPU:
Open Activity Monitor in the Utilities folder. Select All Processes from the Processes dropdown menu. Click twice on the CPU% column header to display in descending order. If you find a process using a large amount of CPU time, then select the process and click on the Quit icon in the toolbar. Click on the Force Quit button to kill the process. See if that helps. Be sure to note the name of the runaway process so you can track down the cause of the problem.
Often this problem occurs because of a corrupted cache or preferences file or an attempt to write to a corrupted log file.
Maybe you are looking for
-
My i Pad 3 shows "cannot Access Find My Friends open the app and review your sign in information to continue sharing your location. And I have two buttons : Later and Open but they don't work. As long as I have this screen situation, I cann't do anyt
-
BAPI or FM Required to create Material Master
IS there any BAPI or Function module avaiable in SAP to create Material Master. The following Two BAPIs uses Call transaction, which I dont want. BAPI_RETAILMATERIAL_CREATE BAPI_STANDARDMATERIAL_CREATE Please let me know if any other Function module
-
Vendor Master bank Details Query
Hi Gurus.. i have developed a program from extracting vendor master and vendor A/P transaction.. in vendor master i have to get bank info like bank key and bank account number with respect to vendor number(lifnr). i have found the field name <b>bnka-
-
How to map multiple source structures to single target structure
Hi all, I have the scenario of 2 input files so i am using BPM for it. I have created the message types of the 3 input files. I have to finally generate an XML file which will contain the data of all the 2 files. That is i have to do 3:1 mapping. Sou
-
Drums were recorded at friends studio to drummers click in headphones. Tempo was not set in logic. All songs were recorded to 120 bpm but the real tempo of songs varies. I've found I can export files [aaf] and load them into a new song [with the corr