Debug commands to troubleshoot client through the WiSM
We been having issues with several laptops that appear to be losing wireless connectivity and i wanted to know if there is a debug command or commands that would allow me to see the process of the client trying to Associate/Authenticate, etc..
Thank you
Vic
This may be a separate question, I am quite familiar with the "debug client" command, however everytime I log out, or am logged out of the console, and then log back in, my "show debug", shows that I am not debugging anything. The client mac is listed, but no Debug Flags are enabled. Is there no way to leave those debug commands on, so the output is put out to a syslog server? Thanks
Similar Messages
-
Show and debug command to troubleshoot roaming
Hi experts,
I have complain that in some areas the voip phones sound choppy. I checked the signal strength in that area and it was actually too many APs with acceptable signal strength. I think it might be that the phone keeps roaming among the APs which caused the packets to drop. I am trying to prove it so they can get the phone vendor to change the roaming threshold. Is there debug and show command I can use to check for the roamin history of a client (with specific MAC address)? The debug client <MAC> doesn't show the roaming activity.
The controller is WISM2 running 7.2.110.0 code
Thanks,If most of your APs are at 7 then I might agree, you have to many access points. But without seeing your design I dont want to comment.
Yes, -65 dBm. But it is very important dont use your laptop to see the signal strength. Rather use the badge itself and use it how the users are using it, around their neck. If they are holding it in their hand, thats a NO NO.
Remember each device hears differently. So if you used your laptop you might see a different dBm sginal than the badge consistently. Always use the device that is having issues.
The 3600 aps can transmist at the following 2.4 GHz levels ..
1 - 100mW <20 dBm>
2 - 50 mW <17 dBm>
3 - 25 mW <14 dBm>
4 - 12.5 mW <11 dBm>
5 - 6.25mW <8 dBm>
6 - 3.12 mW <5 dBm>
7 - 1.56 mW <2 dBm>
You can see if your APs are on 7 they are so low they must have a 10 feet foot print.
Do you have omnipeek or airmagnet to see channel utilization ?
"Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin
"I'm in a serious relationship with my Wi-Fi. You could say we have a connection." -
Debugging inbound call - need debug command
I am debugging what I believe to be a dial plan issue on PGW but want to run a debug command on the ITP to show the actual called number of the inbound call.
What is the best debug command to use to see the inbound called and calling numbers of a call.You are better off capturing an mdl trace from the PGW using per call tracing or using snoop and opening the call in Wireshark.
The ITP will only dump hex values and you will need to decode them yourself since it is not concerned with ISUP layer. You can use the cs7 paklog feature to attach an access list to a linkset and then send the raw data to a syslog server for decoding.
For example:
cs7 paklog x.x.x.x dest-port xxxx src-port yyyy
access-list 2700 instance x permit si all
debug cs7 mtp3 paklog 2700 -
Servlet as a client to the web-service
Hi all, I am new to this field of developing web services.
I have designed a simple web service, that provides some lookup and search operation. I have developed the web service using JWSDP 1.5.0, Tomcat 5.0 and jdk1.5.0_03. I have also developed client applications using the wscomp and ant tools and they are working fine. The applications talk to the web service after I type in the command ant run-client on the command prompt.
Now, I have to develop a servlet which will be the clients to the web service. How do I do that?By reading a tutorial about servlets maybe?
-
Apple Remote Desktop - sending SSH commands to linux clients
Has anyone been able to configure ARD to send SSH commands to linux clients?
The VNC part works, but not sure how to configure the UNIX commands.
We are trying to be able to send rpm, df, etc commands to multiple centos clients at one time...
thanks.not sure how to configure the UNIX commands.
You can't. That's not a feature of ARD. -
Firefox can't open normally without going through the "this is embarrassing" routine; nor does it close down properly; I get the "end program" message and have to say "end now"it also sticks frequently, i.e. screen freezes for a minute or more; should I uninstall and re-install to try and debug?
- I've used Firefox exclusively for around 2 years.
- My outlook express has no problems
- other programs seem unaffected; it seems peculiar to Firefox.
- my main use is surfing the net, primarily entering competitions on line via specialist competition sites.
- every day at some stage(s) I have to switch computer off as Firefox has got very slow/sticky/freezes.
I'm not techy by any means, but I can only thing of un- and re-installing to hopefully start with a clean slate.Sounds like something is keeping Firefox from closing properly. See this: <br />
https://support.mozilla.com/en-US/kb/Firefox+hangs#Hang_at_exit -
The reason I found this problem is that I did a complete reset of my iPhone, so it reset all the content, through settings on the phone. That ended up deleting the ringtones I had. I tried searching up the same tones, however you can't "Install" already purchased stuff like you can in the AppStore.
I can't "iTunes wifi-sync" because you need to have connected at least once to the computer before you can wifi-sync, but because I reset my phone, it doesn't "remember" it once synced with my Mac cause I reset it.
I have gone through the "iTunes connectivity troubleshooting", nothing worked.
http://www.apple.com/support/iphone/assistant/itunes/#section_1
My iPhone charges fine with the USB-Wall outlet adapter, so its not the lightning connector or the USB connector on the other end of the cord.
All the USB ports on my Mac are functionning (working with other cords for printers, etc.), but still the iPhone persists not to be recognized in iTunes.
So I am guessing iTunes is the problem.
Any Help, Solutions, Suggestions, would be appreciated.
Thanks.I had not tried that article, however I already went throught the troubleshooting assistant, which covers everything that article has.
I am about to try to delete and re-install iTunes though, which was mentioned in your artile link.
Thanks for the help.
I'll post my findings/results. -
Hi
I'm just about to pull my hair out with iTunes!! Hvaing been through the troubleshooting soooooooo many times
it said to set up a new iTunes which I done but now it's saying iTunes is an incompatable programe???
The update 10.5 has created more grief as I cant sync my iPhone to my iTunes I have tried the file sharing as
I can't update anything but that's greyed over and I can't tick it?
Every time I open iTunes it opens then doesn't respond, so I have to close and reopen several times and
eventually I can play a tune at least, which I guess is what keeps me going ......... hahaha
Any help would be appreciated!
Thanx heaps !!We don't work for Adobe. We are just users.
You'll want to take this to the proper forum for that product at Adobe PDF Pack (read only)
Good luck. -
Hiding a web item through the command line URL
We use the Web API and command line processing heavily to pass in different filter values, variable values, data providers, etc. to our web reports. I had a requirement within a given area to launch our web reports with the Navigation block visible on the web template. In our commonly used 'default' web template, we currently allow the users to switch this item on/off once they are in the report, but we always have it come up Hidden initially.
My question is this: is there some trick to getting a web item property changed dynamically at execution time from Hidden=X to Hidden= ? I have tried numerous attempts to format a URL to change this behavior, but have been unsuccessful. A sample would be: &ITEM=GR6&MULTI=X&HIDDEN= --> this is intended to make all items with 'GR6' in the name unhidden. But in my case, it ends up making more web items visible than I want. Even specifying the Item name directly does not help.
I have also tried applying it in conjunction with a command sequence from the Web API docs. Is there a particular command that this has to go with (i.e. LDOC? RESET_WEB_ITEM? etc.)? We have a button on the web template that issues the command <SAP_BW_URL ITEM='GR6' MULTI='X' HIDDEN=''> when clicked -- this works fine. How do I apply the same type of logic to the initial URL within the command processing?
Any help would be appreciated. I know that I can resolve this by just creating a copy template with this web item set to Visible instead of Hidden at the launch. I was just thinking I could reuse the main web template and control it through the URL.
Thanks...
Jody ChassereauHeike,
maybe you can help me out on this one:
I'm trying to implement Tobias Kaufmann's How To Paper <i>Web Printing with Excel</i>.
Before calling the respective Abap classes from my web template, I want to hide the web item <i>Hierarchical Filter Selection</i> as this one comes out ugly when downloaded to Excel. So what I'm doing is, I first hide the Filter Selection and then call the Abap classes.
Here is the coding that I am using:
<!-- Web Print with Excel-->
<td class="SAPBEXNavLine"><A href="<SAP_BW_URL
CMD_1='Item=HIERCONTEXTMENU_1&HIDDEN=X'
CMD_2='CMD=PROCESS_HELP_WINDOW&HELP_SERVICE=HELP_SERVICE_PRINT&ITEM=Table_1&SUBCMD=PRINT_EXCEL'>">
<IMG alt="Web Print with Excel" src="/sap/bw/Mime/bex/icons/print.gif" border=0></A></td>
This coding is working fine.
The problem is however, that the <i>Hierarchical Filter Selection</i> is now hidden in my web template. To unhide it, I thought I'd use the coding as above, but add a third command (CMD_3) to make that item visible again.
Here is the coding:
<!-- Web Print with Excel-->
<td class="SAPBEXNavLine"><A href="<SAP_BW_URL CMD_1='Item=HIERCONTEXTMENU_1&HIDDEN=X'
CMD_2='CMD=PROCESS_HELP_WINDOW&HELP_SERVICE=HELP_SERVICE_PRINT&ITEM=Table_1&SUBCMD=PRINT_EXCEL'
CMD_3='Item=HIERCONTEXTMENU_1&HIDDEN='>">
<IMG alt="Web Print with Excel" src="/sap/bw/Mime/bex/icons/print.gif" border=0></A></td>
Unfortunately, only the commands CMD_1 and CMD_3 are being executed (which is kind of useless), the main command CMD_2 however is not.
Do you have any idea why this is happening and how to avoid this?
Really appreciating your help,
Regards,
Yogen -
My emails are on Talktalk.net. I have used Firefox for several years with no trouble but at the end of 2013 only the first page would load from firefox. I contacted talktalk and they got me to reset firefox which worked for a short time. When i contacted them a second time they said the fault was on the browser. Based on comments on M support i updated from version 22 to 26 but with no change. I have today worked through the troubleshooting sheets as far as i am able with no success. I can get at the emails from my phone and via google chrome but not from firefox
Try these;<BR><BR>
Clear the Cache '''''Firefox/Tools > Options > Advanced > Network > Cached Web Content: "Clear Now"'''''<BR><BR>
and<BR><BR>
Remove Cookies '''''Firefox/Tools > Options > Privacy > Cookies: "Show Cookies"'''''<BR><BR>
If that does not help,
'''''[https://support.mozilla.org/en-US/kb/troubleshoot-firefox-issues-using-safe-mode start Firefox in Safe Mode]'''''.
Let us know how you do. -
The main part of the safari page is grey and won't respond/can't type in any commands. I can move back through the previous pages, and even open new ones via the URL, but can't get onto the main part of the page and I can't get onto the 9 page option. !?
Help, please.Try clearing Safari's cache : Settings > Safari > Clear Cache (and Clear History)
If that doesn't work then try closing Safari completely and then re-open it : from the home screen (i.e. not with Safari 'open' on-screen) double-click the home button to bring up the taskbar, then press and hold any of the apps on the taskbar for a couple of seconds or so until they start shaking, then press the '-' in the top left of the Safari app to close it, and touch any part of the screen above the taskbar so as to stop the shaking and close the taskbar.
A third option is a reset : press and hold both the sleep and home buttons for about 10 to 15 seconds (ignore the red slider), after which the Apple logo should appear - you won't lose any content, it's the iPad equivalent of a reboot. -
I went through an Adobe update and when my computer rebooted, the default font for everything was in italics. For example, when I go to Yahoo.com, the headings for all the news articles and tabs are in italics. I tried going through the Troubleshooting steps to no avail. I am frustrated because I followed the advice of checking the default font under Tools, then I opened the browser in Safe Mode, then I checked to make sure all the fonts were available. So how can I get my fonts back to normal? The italics gives me a headache.
The usual cause of that issue is a corrupted or missing font that Firefox replaces by another, in this case a bold, font.
As a test you can try to disable the default font and choose a few different fonts (Arial, Verdana, Tahoma, Times New Roman) to see if you can identify the culprit.<br />
you will have to reinstall that corrupted font. -
Running the Archiving actions through the Command Line
Hi,
I am not able to import and export archives using command line tools. I want to directly transfer the archive and don’t want to use a shared location. I have created the scripts that I need to run. For that I have created a sequence of steps that needs to be followed. I have mentioned the steps and the command file that I run for each step.
1) Created a target archive on the target server and set the IsTargetable
<?hda version="10.1.3.3.3 (080807)" jcharset=UTF8 encoding=utf-8?>
@Properties LocalData
IdcService=ADD_ARCHIVE
IDC_Name=CS98310
aArchiveName=TargetArchive
aIsTargetable=1
aArchiveDescription=This is an target archive
aCopyWebDocuments=1
@end
2) Created a source archive on the source server and set the target archive for this source archive as the target archive created in step 1.
<?hda version="10.1.3.3.3 (080807)" jcharset=UTF8 encoding=utf-8?>
@Properties LocalData
IdcService=ADD_ARCHIVE
IDC_Name=idc
aArchiveName=SourceArchive
aArchiveDescription=This is an source archive
aCopyWebDocuments=1
aTargetArchive=CS98310/TargetArchive
aIsTargetable=0
aExportQuery=Standard Query ValuePanel UseExportDate 0 AllowExportPublished 0 AllRevisions 1 LatestRevisions 0 NotLatestRevisions 0 MostRecentMatching 0 CurrentIndex 0 Clauses dDocName:sqlEq: 20 CustomQuery dDocName%=%'20' IsCustom 0
aIsAutomatedTransfer=0
@end
3) Create a query for the source archive to select the content
aExportQuery=Standard Query ValuePanel UseExportDate 0 AllowExportPublished 0 AllRevisions 1 LatestRevisions 0 NotLatestRevisions 0 MostRecentMatching 0 CurrentIndex 0 Clauses dDocName:sqlEq:20 CustomQuery dDocName%=%'20' IsCustom 0
(This is added in the previous step)
4) Export the source archive on the source server
@Properties LocalData
IdcService=EXPORT_ARCHIVE
aArchiveName=SourceArchive
IDC_Name=idc
dataSource=RevisionIDs
@end
5) Transfer the source archive to the target archive from the source server
@Properties LocalData
IdcService=TRANSFER_ARCHIVE
aArchiveName=SourceArchive
IDC_Name=idc
@end
6) Import the target archive on the target server
@Properties LocalData
IdcService=IMPORT_ARCHIVE
aArchiveName=TargetArchive
IDC_Name=idc
aImportDocuments=true
@end
The issue comes while creating the archive. I am not able to set the parameters “aIsTargetable” for the target archive and “aExportQuery and aTargetArchive” for the source archive.
Now I create the archive with the archiver utility and tried running the commands (from step 3), but still it fails in the transfer command. The error comes that “aTargetArchive” parameter cannot be found. Now if I do the entire process through the Archiver Tool, its works fine and I am able to view the documents on the target server. I am not able to understand the reason. Is there a problem in the Command Files?
Also I want to check if I can automate it without deleting the batch files and their associated content file.
Thanks,
NoelAbout dbms_output the answer from Roberto is correct.
About other things see How to view and set current directory to run a script in sql plus. -
Can I give access to ICQ through the Oracle Messenger client?
Can I give access to ICQ through the Oracle Messenger client, is similar JIT in Jabber?
you can try, but it will not be supported by Oracle Support.
-
How can i run application client from the command prompt ?
Hi,
I'm new to java & EJB. so can any body tell me the command to run the application client from the command prompt. Here is the code to print hello world:
/* Remote interface */
public interface Hello extends javax.ejb.EJBObject
public String hello() throws java.rmi.RemoteException;
/* Home interface */
public interface HelloHome extends javax.ejb.EJBHome
Hello create() throws java.rmi.RemoteException, javax.ejb.CreateException;
/* Stateless session bean class */
public class HelloBean implements javax.ejb.SessionBean
private javax.ejb.SessionContext ctx;
public void ejbCreate(){
System.out.println("ejbcreate()");
public void ejbRemove(){
System.out.println("ejbRemove()");
public void ejbActivate(){
System.out.println("ejbActivate()");
public void ejbPassivate(){
System.out.println("ejbejbPassivate()");
public void setSessionContext(javax.ejb.SessionContext ctx){
this.ctx=ctx;
public String hello(){
System.out.println("hello()");
return "Hello, world!";
/*Client class */
import javax.naming.Context;
import javax.naming.InitialContext;
import java.util.Properties;
public class HelloClient
public static void main(String[] args) throws Exception{
Properties props=System.getProperties();
Context ctx=new InitialContext(props);
Object obj=ctx.lookup("HelloHome");
HelloHome home=(HelloHome)javax.rmi.PortableRemoteObject.narrow(obj,HelloHome.class);
Hello hello=home.create();
System.out.println(hello.hello());
hello.remove();
I have stored .java files in c:\ejb
I have successfully created the .class files using javac command in the following directory :
c:\ejb
I have also created Helloworld.ear file in c:\ejb using sun application server which contains the following files:
ejb-jar-ic.jar
app-client-ic.jar
sun-j2ee-ri.project
application.xml
sun-application.xml
Manifest.mf
But the problem is that i'm not able to run the HelloWorld.class file successfully from the command prompt. So please suggest me the comand.
Thanx in advance.
Best regards,
PankajHi
You can run this code from the command prompt in the same way as you run any other simple java program. The only thing is you need to set the Home and Local interfaces in the classpath.And obviously if u had deployed the bean in ur app server container, then its all over.
And one more thing is that u need to set the provider URL in the InitialContext created in the client program.
Thanks
Arun B
Maybe you are looking for
-
I have a Mac-book, i always use Firefox and never Safari nor anything else! I had it on for a long time, never done any sever crashes! but just a few days ago, Firefox asked for an upgrade which I've done. Now every time I try to run an online video
-
Unable to get database connection from loaded java class in oracle
Hi all, I am trying to call java class method from oracle function, but getting below exception, while creating connection. SQL> select charge_calculation(1,'2011-06-01', 'E') from dual; select charge_calculation(1,'2011-06-01', 'E') from dual ERROR
-
Error while J1INCHLN - Business Place for document could not be determined
Dear All Experts, I am getting below error while running J1INCHLN Business Place for document could not be determined. For updating Business Place & Section Code I am running J1INPP Update Business Place information in FI document. So I am getting er
-
What are the best free cases available 8/12/10?
I ordered 4 (32) on Monday and it was delivered 48 hours later. Last night I used the app for the free case and selected Speck's PixelSkin HD. A search of various keywords in the Apple and AT&T forums and more general searches on the web made it uncl
-
My external monitor has become very difficult to use with my PowerBook, but I don't know what I did to cause this. I am using a Samsung SyncMaster 910T as an external display via the Apple VGA - DVI adaptor with a 15-inch PB G4, and for years it has