Decent line rate, throughput not consistent!

Hi folks,
On Wednesday I upgraded to the Broadband unlimited package, and with that got a Homehub 4.
Router setup went fine and broadband connected.
It has synced at a good rate but when conducting speed tests, the results range from a download of 15mb right down to the lowest Ive seen of 0.2mb. The results can be quite different from two tests done straight after eachother. There is no consistency and seems to be jumping all over the place.
The upload results remain around the 1mb mark.
My previous hub was a homehub 1 and although the last download sync I remember was 3.2mb, it was at least steady and I had no problems with it, besides the occasional reboot required.
Sync stats below:
Connection time:
0 days, 01:58:08
Downstream:
18.71 Mbps
Upstream:
1.137 Mbps
Other stats:
16:15:13, 06 Dec.
( 98.830000) DSL noise margin: 5.90 dB upstream, 3.00 dB downstream
16:15:11, 06 Dec.
( 97.710000) DSL line rate: 1163 Kbps upstream, 19160 Kbps downstream
results of recent diagnostic with BTWholesale:
1. Best Effort Test: -provides background information.
Download speed achieved during the test was - 3.01 Mbps
For your connection, the acceptable range of speeds is 4 Mbps-21 Mbps.
IP Profile for your line is - 16.9 Mbps
Upload speed achieved during the test was - 0.99Mbps
Additional Information:
Upstream Rate IP profile on your line is - 0.83 Mbps
Looking around some of the other posts on the forum with similar issues, I suspect this could be an issue for a mod to sort out?
Thanks for reading

Speed check @ 21:15
Download speed achieved during the test was - 14.83 Mbps
For your connection, the acceptable range of speeds is 4 Mbps-21 Mbps.
IP Profile for your line is - 15.21 Mbps
Speed tests done today seem to have stabilised around the 14-15mb mark.
I noticed that my router reset this morning, with the noise increasing to 6db, not sure if this would help stabilise the throughput?
04:13:59, 07 Dec.
(43225.730000) DSL noise margin: 5.90 dB upstream, 6.00 dB downstream
04:13:58, 07 Dec.
(43224.700000) DSL line rate: 1147 Kbps upstream, 17240 Kbps downstream
I'll keep an eye on it over the next couple of days.

Similar Messages

Spacing between lines is not consistent!

Dear co-community members,
I am a happy Pages user since a couple of months, but I just discovered a weird thing and that is: the spacing between the lines is not consistent! I am typing my document with margins left and right: 2,25 upper and under: 2,00. I use Helvetica Neue Light in 10. And I have tried several spacings: 1,15 - 1,3 - 1,35 - 1,4 but the spaces between the lines are not consistently as big or as small as they need to be.
I discovered this when I was test printing it and I saw something was off - on paper, I thought it was my printer. But I also checked the document again: spacing was 'the same' in the whole document according to the info window. But I could see it with my bare eyes that it was not consistent (on screen nor on paper). I put the screen on 200% and I took a ruler and the spaces vary with 1mm when for example the spacing is set on 1,3. I don't think this is normal and I cannot find any solution nor explanation for it.
I am using a MBP Retina 13" late 2012 and I have the most updated/recent version of Pages/OSX. Please let me know whether I did something wrong or are my eyes just too good hahah - or it is an 'error' in Pages .
Kind Regards,
Ning.

@PeterBreis0807 & @Barry
I actually don't have any objects or other material/fonts in my text (yet) that are not uniform size . I wanted to make a print screen from a part of my text, but I am not sure if I am allowed to post that here since I am typing a literature review with references.
I btw do have headings in small capital (Helvetica Neue - Medium), it might not be Helvetica Neue Light also but I have never had problems with headings in another font causing inconsistent spacing between the rest of my text .
Thank you for your reply!
Ning.

Line rate always changing / Hub resetting itself

Hello
For the past 6 or 7 months we have seen dramatic fluctuations in our Broadband download speed. This change always comes about as a result of our our Home Hub 4 seemingly restting itself: we have normal internet use with a blue light on, but then the Hub will flash orange for a while and come back with a blue light. There is no pattern regarding the time of day; it's completely random.
I've been informed that a resetting connection will only inform the exchange that there is a problem, thus prompting the "IP Profile to be reduced" to make things stable. Surely then this isn't supposed to be happening?
There was a time when we would always get around 2.7 - 3.3 Mbps line rate, which is the best we could expect for our area and the distance from the exchange. The download speeds associated with that were good enough for us, but we can never seem to get that now.
The Event Log will report the process described above as: 'Failed to Resolve Host' and, once the connection is re-established, the line rate will usually be lower than it was before. As an example, a line rate of approx 2.3 Mbps will drop to about 1.3 Mbps. Sometimes this process will return a slightly higher line rate!
This happens approximately once every day, but the line rate is never the decent 3 Mbps we used to get...Sometimes I get lucky by manually resetting the Hub and the line rate will be 2.5 Mbps...but it isn't long before it resets itself and, again, we have about 1.2 Mbps.
Current event log:
12:24:27, 18 Sep.
( 97.940000) DSL noise margin: 5.90 dB upstream, 6.00 dB downstream
12:24:26, 18 Sep.
( 96.910000) DSL line rate: 934 Kbps upstream, 1315 Kbps downstream
12:24:11, 18 Sep.
( 81.000000) CWMP: session closed due to error: Could not resolve host
In the last month there was a small amount of noise on the telephone line (we were looking into it but it appears to have gone), but this line rate fluctuation started long before then anyway. Phone call with the Telephone department team told me there appears to be no problem with the line. We have also had 3 different Hubs during that time, so it isn't a Hub issue. Filters in place and Master Socket is in use. Using the test socket yeilds same problems.
Further questions if anyone is able to answer them:
Besides interference from noise, is there a good reason for the Hub to go through this process and force lower speeds upon us? Is the exchange throttling us or something?
For a period last year we were getting 380 kB/s in a speed test and that was fine to use because it matches the line capabilities that we have always been quoted. I don't understand why we can't have a similar speed now. We don't even get > 300kB/s during off peak times. Is it normal for our DL speed to now be always be about 180 kB/s? We were told during our recent re-contract that there is no longer any capping.

presumbly the previous stats were from the test socket as new stats are just the same
any exchnage problems http://usertools.plus.net/exchanges/mso.php
http://usertools.plus.net/exchanges/?
http://btbusiness.custhelp.com/app/service_status
http://bt.custhelp.com/app/answers/detail/a_id/15036
http://community.plus.net/exchange-information/
If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

Very slow download speed though modem line rate no...

Hi
I recently noticed (today, 31st December) that our download speed had dropped very low, to approx 0.5Mbps. The upload speed is normal, approx 1Mbps. The modem line rate is however normal (8Mbps dowm, 1Mbps up). I have checked the download speed using http://speedtest.btwholesale.com/. I am at postcode SK237FN and have had consistently reliable download speeds for several years, 5-7Mbps.
Please help!
I already tried rebooting my router but this has not improved matters.
Thanks...
Test Result
Best Effort Test: -provides background information.
Download Speed
0.59 Mbps
0 Mbps
7.15 Mbps
Max Achievable Speed
Download speedachieved during the test was - 0.59 Mbps
For your connection, the acceptable range of speeds is 2 Mbps-7.15 Mbps.
IP Profile for your line is - 7.2 Mbps
Solved!
Go to Solution.

Hi
Thanks for your quick reply.
I don't use a BT "home hub"; I use a Billion router, ADSL status below.
The speedtest was performed using a wired connection.
BR
Mike
Mode
ADSL_2plus
Traffic Type
ATM
Status
Up
Link Power State
L0
Downstream
Upstream
Line Coding (Trellis)
On
On
SNR Margin (dB)
4.2
6.3
Attenuation (dB)
33.0
15.9
Output Power (dBm)
0.0
12.8
Attainable Rate (Kbps)
9184
1056
Rate (Kbps)
7438
1052
MSGc (# of bytes in overhead channel message)
59
10
B (# of bytes in Mux Data Frame)
232
150
M (# of Mux Data Frames in FEC Data Frame)
1
1
T (Mux Data Frames over sync bytes)
1
1
R (# of check bytes in FEC Data Frame)
16
0
S (ratio of FEC over PMD Data Frame length)
0.9979
4.5584
L (# of bits in PMD Data Frame)
1996
265
D (interleaver depth)
32
1
Delay (msec)
8
1
INP (DMT symbol)
1.00
0.00
Super Frames
364092
322883
Super Frame Errors
63
0
RS Words
23665906
882081
RS Correctable Errors
1466757
0
RS Uncorrectable Errors
711
0
HEC Errors
702
0
OCD Errors
0
0
LCD Errors
0
0
Total Cells
103594167
14634218
Data Cells
24717224
1770221
Bit Errors
0
0
Total ES
14
0
Total SES
1
0
Total UAS
76
76

GR/IR Clearing Account 2..... Not Consistent

SAP Experts,
I blocked GR/IR clearing account temporarely while I updated the open line item field. It turns out that after I finish running the program and unblocked the account. Receiving ca no longer receeive into teh account it says "G/L Accuont 2...... Not Consistent"
Does anyone knows what could possibly be?

I was able to go into IMG bring the field " Only Balances in Local Currency" then went into account brought it to a "ZERO Balance" with TCODE FB50. Went into FS00 and updated field. Then reversed entry, and it works fine.

T-code: F-02 (Balancing field "Profit Center" in line item 001 not filled)

Dear Experts,
I am getting following error while i am doing transfer by using t-code F-02.
"Quote
Balancing field "Profit Center" in line item 001 not filled
Message no. GLT2201
Diagnosis
The field Profit Center marked as balancing is not filled with any value in line item 001, even after document splitting.
System Response
The document cannot be posted.
Procedure
First check your entries.
Additional causes could be:
u2022 No value can be derived for this field from the current document data.
u2022 You have entered a document type that is not designed for this business purpose.
Procedure for System Administration
Customizing
Unquote"
Where do you thing the mistake is and what i have to do? Please resolve my problem.
Thanks advance,
Best Regards.
Ripon Kumar Paul

Hi
Balance Sheet Accounts are required to be split in case you have document splitting activated u2026.. and in your case the profit center is made mandatory for the documents to get splitted u2026.. and the profit center would be derived from cost centeru2026u2026u2026. therefore to split the document by using document type u2013 SA through F-02 we need to do further settings, i.e., you need to configure u201CExtended Document Splitting Configurationu201D
For example: Rent expenditure is been posted which is having more than 2 Debits and consisting of different Cost Centers and posting to Rent Payable A/c which is a Balance sheet A/cu2026u2026.
Path: Financial Accounting (New) - - General Ledger Accounting (New) - - Business Transactions - - Document Splitting - - Extended Document Splitting -- Define Document Splitting Rule
Define your Business Transaction variant and for that variant define document splitting rule u2026u2026u2026.. where in you need to activate Automatically split check box for the desired categories.
Regards,
Sathish

GL Account not consistent

Hi
When we are processing MIGO for a PO we are getting error message GL ac so and so in not consistent and if I double click on that message below detial message is getting displayed:
This line item carries the "W" posting line identification. The master record for GL Account 2150000 in company code 1000 must have the "balance only in local currency " indicator if the W identifier is set.
What is "W" posting line identification. Please let me know the solution for this issue
Regards
Padma.

Hi,
As this error is pertaining to GL master check this account under FS00 and tick "only balance in local currency" as it is your GR/IR clearing account which should be managed as open item basis.
Moreover, also make sure field status to this GL (for line item) and of account group (obd4) are in sync.
In OBYC, you have assigned this account under your wrx i.e. GR/IR clearing.
Hope above will help you.
Regards,
Valay Pandya

Intercompany billing exchange rate is not updated on change of the currency

Hi,
I create a intercompany billing via VF01 with reference to a outbound delivery, and the currency is picking up from the customer master which is USD. But I need to change the currency to be the same as the PO which is GBP. So I change the currency field from USD to GBP in VF01 (both header and item level), the exchange rate field remain unchanged and still showing the USD rate instead, and the price is wrong.
Anyone know what happend to this? Appreciate your advice.
Thanks,
YH

Hi Damu,
Once you change the header currency, line item currency will be changed also.
My problem is even I've change the currency to let say GBP, the exchange rate shown in the billing document is still in USD rate, but NOT in GBP rate.

Metadata of Controller EMPTYVIEW Is Not Consistent.

Hi,
After upgrading NW04s from SP07 to SP11, one of my web dynpro for ABAP application gives the following error on execution.
I am also getting a system dump. I have checked all the necessary services in SICF & most of the required services are active. Does any one have some idea of how I can resolve this error.
Error when processing your request
What has happened?
The URL http://ustca644.kcc.com:8086/sap/bc/webdynpro/sap/zvmkc_tsvm_main/ was not called due to an error.
Note
The following error text was processed in the system PGW : Metadata of Controller >EMPTYVIEW< Is Not
Consistent. "View Controller" Does Not Contain a "View"
The error occurred on the application server ustca644_PGW_20 and in the work process 0 .
The termination type was: RABAX_STATE
The ABAP call stack was:
Method: CONTROLLER_KIND_TO_TEXT of program CL_WDY_RG_META_SERVICE========CP
Method: CONSTRUCTOR of program CL_WDY_RG_CONTROLLER==========CP
Method: GET_CONTROLLER_PARTS of program SAPLWDR_RUNTIME_REPOSITORY
Method: SAVE_COMPONENT of program SAPLWDR_RUNTIME_REPOSITORY
Method: SAVE of program SAPLWDR_RUNTIME_REPOSITORY
Function: WDR_SAVE_REPOSITORY of program SAPLWDR_RUNTIME_REPOSITORY
Method: SAVE of program CL_WDR_RR_DB==================CP
Function: WDY_WB_GENERATE_INTERNAL of program SAPLWDY_WB_ACTIVATION_SERVICES
Function: WDY_WB_GENERATE of program SAPLWDY_WB_ACTIVATION_SERVICES
Method: CONSTRUCTOR of program SAPLWDR_RUNTIME_REPOSITORY
What can I do?
If the termination type was RABAX_STATE, then you can find more information on the cause of the termination in the system
PGW in transaction ST22.
If the termination type was ABORT_MESSAGE_STATE, then you can find more information on the cause of the termination on
the application server ustca644_PGW_20 in transaction SM21.
If the termination type was ERROR_MESSAGE_STATE, then you can search for more information in the trace file for the work
process 0 in transaction ST11 on the application server ustca644_PGW_20 . In some situations, you may also need to analyze
the trace files of other work processes.
If you do not yet have a user ID, contact your system administrator.
Error code: ICF-IE-http -c: 400 -u: C14216 -l: E -s: PGW -i: ustca644_PGW_20 -w: 0 -d: 20070222 -t: 222514 -v: RABAX_STATE -e:
UNCAUGHT_EXCEPTION
HTTP 500 - Internal Server Error
Your SAP Internet Communication Framework Team
System Dump
Runtime Errors         UNCAUGHT_EXCEPTION
Exception              CX_WDY_RG_MD
Date and Time          02/22/2007 22:25:14
Short text
An exception occurred that was not caught.
What happened?
The exception 'CX_WDY_RG_MD' was raised, but it was not caught anywhere along
the call hierarchy.
Since exceptions represent error situations and this error was not
adequately responded to, the running ABAP program
'CL_WDY_RG_META_SERVICE========CP' has to be
terminated.
What can you do?
Note down which actions and inputs caused the error.
To process the problem further, contact you SAP system
administrator.
Using Transaction ST22 for ABAP Dump Analysis, you can look
at and manage termination messages, and you can also
keep them for a long time.
Error analysis
An exception occurred which is explained in detail below.
The exception, which is assigned to class 'CX_WDY_RG_MD', was not caught and
therefore caused a runtime error.
The reason for the exception is:
Metadata of Controller >EMPTYVIEW< Is Not Consistent. "View Controller" Does
Not Contain a "View"
How to correct the error
If the error occures in a non-modified SAP program, you may be able to
find an interim solution in an SAP Note.
If you have access to SAP Notes, carry out a search with the following
keywords:
"UNCAUGHT_EXCEPTION" "CX_WDY_RG_MD"
"CL_WDY_RG_META_SERVICE========CP" or "CL_WDY_RG_META_SERVICE========CM001"
"CONTROLLER_KIND_TO_TEXT"
If you cannot solve the problem yourself and want to send an error
notification to SAP, include the following information:
1. The description of the current problem (short dump)
To save the description, choose "System->List->Save->Local File
(Unconverted)".
2. Corresponding system log
Display the system log by calling transaction SM21.
Restrict the time interval to 10 minutes before and five minutes
after the short dump. Then choose "System->List->Save->Local File
(Unconverted)".
3. If the problem occurs in a problem of your own or a modified SAP
program: The source code of the program
In the editor, choose "Utilities->More
Utilities->Upload/Download->Download".
4. Details about the conditions under which the error occurred or which
actions and input led to the error.
System environment
SAP-Release 700
Application server... "ustca644"
Network address...... "165.28.85.39"
Operating system..... "Windows NT"
Release.............. "5.2"
Hardware type........ "4x AMD64 Level"
Character length.... 16 Bits
Pointer length....... 64 Bits
Work process number.. 0
Shortdump setting.... "full"
Database server... "PGWA"
Database type..... "DB2"
Database name..... "PGW"
Database user ID.. "SAPR3"
Char.set.... "C"
SAP kernel....... 700
created (date)... "Oct 30 2006 00:08:55"
create on........ "NT 5.2 3790 Service Pack 1 x86 MS VC++ 14.00"
Database version. "DB2CLI.DLL 08.02.0003 "
Patch level. 83
Patch text.. " "
Database............. "DB2 for OS/390 7.1, DB2 for OS/390 8.1, DB2 for OS/390
9.1"
SAP database version. 700
Operating system..... "Windows NT 5.0, Windows NT 5.1, Windows NT 5.2"
Memory consumption
Roll.... 16192
EM...... 16759360
Heap.... 0
Page.... 0
MM Used. 12837904
MM Free. 3918160
User and Transaction
Client.............. 400
User................ "C14216"
Language Key........ "E"
Transaction......... " "
Program............. "CL_WDY_RG_META_SERVICE========CP"
Screen.............. "SAPMHTTP 0010"
Screen Line......... 2
Information on Caller ofr "HTTP" Connection:
Plug-in Type.......... "HTTP"
Caller IP............. "165.28.239.30"
Caller Port........... 8086
Universal Resource Id. "/sap/bc/webdynpro/sap/zvmkc_tsvm_main/"
Information on where terminated
Termination occurred in the ABAP program "CL_WDY_RG_META_SERVICE========CP" -
in "CONTROLLER_KIND_TO_TEXT".
The main program was "SAPMHTTP ".
In the source code you have the termination point in line 20
of the (Include) program "CL_WDY_RG_META_SERVICE========CM001".
Source Code Extract
Line
SourceCde
1
method CONTROLLER_KIND_TO_TEXT .
2
3
data:
4
cref_View type ref to cl_wdy_md_view,
5
ctlr_Type type Wdy_Md_Controller_Type.
6
7
ctlr_Type = controller->get_type( ).
8
9
case ctlr_Type.
10
11
when wdyn_ctlr_type_custom.
12
controller_type_as_text = 'CUSTOM'.
13
14
when wdyn_ctlr_type_view.
15
controller_type_as_text = 'VIEW'.
16
if ( ABAP_FALSE eq Controller->Has_View( ) ).
17
" view controller must have a view
18
gi_Cx_Text = Controller->Get_Name( ).
19
gi_Cx_Hint = '"View Controller" enthält keine "View"'(NVW).
>>>>>
raise exception type Cx_Wdy_Rg_Md
21
exporting
22
TextId =     Cx_Wdy_Rg_Md=>Controller_Data
23
Controller = gi_Cx_Text
24
Reason =     gi_Cx_Hint.
25
26
else.
27
gi_Cx_Text = Controller->Get_Name( ).
28
if ( gi_Cx_Text eq 'EMPTYVIEW' ).
29
return.
30
endif.
31
32
" sanity check against illegal CL_WDY_MD_EMPTY_VIEW
33
try.
34
cref_View ?= Controller->Get_View( ).
35
if ( cref_View is initial ).
36
gi_Cx_Text = Controller->Get_Name( ).
37
gi_Cx_Hint = '"View Controller" enthält keine "View"'(NVW).
38
raise exception type CX_Wdy_Rg_Md
39
exporting
Contents of system fields
Name
Val.
SY-SUBRC
0
SY-INDEX
1
SY-TABIX
2
SY-DBCNT
0
SY-FDPOS
7
SY-LSIND
0
SY-PAGNO
0
SY-LINNO
1
SY-COLNO
1
SY-PFKEY
SY-UCOMM
SY-TITLE
HTTP Control
SY-MSGTY
SY-MSGID
SY-MSGNO
000
SY-MSGV1
SY-MSGV2
SY-MSGV3
SY-MSGV4
SY-MODNO
0
SY-DATUM
20070222
SY-UZEIT
222514
SY-XPROG
SY-XFORM
Active Calls/Events
No.   Ty.          Program                             Include                             Line
Name
22 METHOD       CL_WDY_RG_META_SERVICE========CP    CL_WDY_RG_META_SERVICE========CM001    20
CL_WDY_RG_META_SERVICE=>CONTROLLER_KIND_TO_TEXT
21 METHOD       CL_WDY_RG_CONTROLLER==========CP    CL_WDY_RG_CONTROLLER==========CM001    25
CL_WDY_RG_CONTROLLER=>CONSTRUCTOR
20 METHOD       SAPLWDR_RUNTIME_REPOSITORY          LWDR_RUNTIME_REPOSITORYF11            684
LCL_SAVE_REPOSITORY=>GET_CONTROLLER_PARTS
19 METHOD       SAPLWDR_RUNTIME_REPOSITORY          LWDR_RUNTIME_REPOSITORYF11             91
LCL_SAVE_REPOSITORY=>SAVE_COMPONENT
18 METHOD       SAPLWDR_RUNTIME_REPOSITORY          LWDR_RUNTIME_REPOSITORYF11             29
LCL_SAVE_REPOSITORY=>SAVE
17 FUNCTION     SAPLWDR_RUNTIME_REPOSITORY          LWDR_RUNTIME_REPOSITORYU02             27
WDR_SAVE_REPOSITORY
16 METHOD       CL_WDR_RR_DB==================CP    CL_WDR_RR_DB==================CM002     3
CL_WDR_RR_DB=>SAVE
15 FUNCTION     SAPLWDY_WB_ACTIVATION_SERVICES      LWDY_WB_ACTIVATION_SERVICESU04        279
WDY_WB_GENERATE_INTERNAL
14 FUNCTION     SAPLWDY_WB_ACTIVATION_SERVICES      LWDY_WB_ACTIVATION_SERVICESU01         84
WDY_WB_GENERATE
13 METHOD       SAPLWDR_RUNTIME_REPOSITORY          LWDR_RUNTIME_REPOSITORYF12             77
LCL_REPOSITORY=>CONSTRUCTOR
12 METHOD       SAPLWDR_RUNTIME_REPOSITORY          LWDR_RUNTIME_REPOSITORYF01             17
LCL_COMPONENT=>CONSTRUCTOR
11 METHOD       SAPLWDR_RUNTIME_REPOSITORY          LWDR_RUNTIME_REPOSITORYF01            669
LCL_COMPONENT=>IF_WDR_RR_COMPONENT~GET_USED_COMPONENT
10 METHOD       SAPLWDR_RUNTIME_REPOSITORY          LWDR_RUNTIME_REPOSITORYF01            245
LCL_COMPONENT=>IF_WDR_RR_COMPONENT~CREATE_COMPONENT_USAGE
9 METHOD       CL_WDR_MESSAGE_WINDOW=========CP    CL_WDR_MESSAGE_WINDOW=========CM001    30
CL_WDR_MESSAGE_WINDOW=>CONSTRUCTOR
8 METHOD       CL_WDR_APPLICATION_WINDOW=====CP    CL_WDR_APPLICATION_WINDOW=====CM00K     6
CL_WDR_APPLICATION_WINDOW=>INITIALIZE
7 METHOD       CL_WDR_CLIENT_COMPONENT=======CP    CL_WDR_CLIENT_COMPONENT=======CM004    59
CL_WDR_CLIENT_COMPONENT=>DISPLAY_TOPLEVEL_COMPONENT
6 METHOD       CL_WDR_CLIENT_APPLICATION=====CP    CL_WDR_CLIENT_APPLICATION=====CM00L    30
CL_WDR_CLIENT_APPLICATION=>INIT
5 METHOD       CL_WDR_MAIN_TASK==============CP    CL_WDR_MAIN_TASK==============CM00I    40
CL_WDR_MAIN_TASK=>EXECUTE
4 METHOD       CL_WDR_MAIN_TASK==============CP    CL_WDR_MAIN_TASK==============CM00J    69
CL_WDR_MAIN_TASK=>IF_HTTP_EXTENSION~HANDLE_REQUEST
3 METHOD       CL_HTTP_SERVER================CP    CL_HTTP_SERVER================CM00I   524
CL_HTTP_SERVER=>EXECUTE_REQUEST
2 FUNCTION     SAPLHTTP_RUNTIME                    LHTTP_RUNTIMEU02                      929
HTTP_DISPATCH_REQUEST
1 MODULE (PBO) SAPMHTTP                            SAPMHTTP                               13
%_HTTP_START

Hi Kim,
Please try the following:
Try to reactivate the component
If this does not help, please create an OSS ticket and the SAP colleagues will help you to fix the problem. Please add exact information about the component and open a connection to your system.
Ciao, Regina

Since upgrading to Maverick my iPhoto does not consistently download my Nikon or my Canon camera photos.

Since upgrading to Maverick my iPhoto does not consistently download my Nikon or my Canon camera photos. Occasionally it will recognize and download photos, most of the time though it hangs in "loading" mode with nothing downloaded. I've unplugged, replugged numerous times, tried a different USB port, tried the two cameras so it's not the camera or line that's the issue, turned the computer off, turned iphoto off, turned everything else off and stil nothing. I need my photos for my work and can't get to them, this seems to be an issue with Maverick AGAIN!!! Is there a fix? HELP! Thanks!

iPhoto Version 9.5.1
Thank you for your help Terence. I had 140 photos on my Nikon, none were viewable in iphoto, in Image Capture 5 were viewable, 135 weren't. I tried importing one to my desktop but it remained static and didn't move over. I just deleted all the photos on my camera, took a fresh photo and after waiting a good 4 minutes finally uploaded to both iphoto and Image Capture. As this took so long for one photo I'm wondering if the memory in my computer would impact the speed. I have 350GB used and 150GB left
By reformat the cards do you mean the flash card in the camera? I don't know how to do that, it's less that 6 months old.

Reset Cleared Doc - Balance of the line item is not zero" Message no. F5136

I have this error : Balance of the line item is not zero" Message no. F5136
This error arise when we tried to reset cleared document dated June 6,2007 during data migration from Legacy system to SAP.
We wanted to reset this cleared document because it was wrong executed (cleared) way back 2007.
The entries are:
Debit to GL (B/S) --> 3,758.48
Credit (1100039-Vendor) with special GL (408319) --> 3,758.48
=====================================================
For us to correct the clearing, we need to reset first the cleared document via FBRA, however, this error arise saying "Balance of the line item is not zero" with Message no. F5136.
I read several posted issue here, however, it doesn't resolve my problem.
Hoping to hear from your inputs on this problem.
Regards,
macalonge

Dear:
SAP Note 400530 - FBRA - F5136: Balance of line items not zero
describes your issue as
Summary
Symptom
A payment using a payment card fails, in other words, the payment is reversed using Transaction FBRC where the customer or vendor item is reopened.It is not possible to reset a payment document posted again for the open customer or vendor item by using Transaction FBRA, "Reset Cleared Items" and it responds with the error message "Balance of the line items is not zero".
Other terms
Error message F5136, FBRA, FBRC, payment cards
Solution
A solution is available in the Support Package for Release 4.0B and 4.6C. An advance correction is possible. The solution consists of a repair report, so that the current payment document can be reset by means of 'Reset Cleared Items', and of a correction.
1. Repair-report ZREPAIR_BSEGC_FBRA:Create it temporarily as a test report using Transaction SE38. First the current payment/clearing document must be cleaned up of payment card data by means of the repair-report. Afterwards you can reset the payment document by means of 'Reset Cleared Items'. The report takes the current payment document as a parameter. In this case only changes are made to the database if the option "DO_UPD" is set.
2. Advance correction:Supplement the interface for function module CREDIT_CARD_POST_REFUSAL with table parameter T_BSEG with reference type BSEG. The following describes the procedure in more detail.
a) Transaction SE37: Enter function module CREDIT_CARD_POST_REFUSAL and choose "Change".
b) On the "Tables" tab page, create parameter T_BSEG with reference to structure BSEG.
c) Save and activate the function module.
3. After you implemented the correction or the R/3 Support Packages valid for this note, read Note 450081 to avoid the unwanted deletion of payment card data.
Hope it will help
Regards

Balance of S_ALR_87012168 and S_ALR_87012167 is not consistent with FBL5N

Dear all,
Could you kindly let me what's the reason that cause S_ALR_87012168 and S_ALR_87012167 is not consistent with FBL5N.
When view line item anlaysis the line item is the same with FBL5N, but in the first page of due / not due anlysi, the result is not the same?
Thanks bnd Best Regards.
CSY.

Hello
first thing you should do it is to run the programm SAPF190 if you don't activate NewLedger or TFC_COMPARE_VZ if new ledger is on.
These programms will check the index of the data and compare the amount between index and BSEG/FAGLFLEXA table.
Second point, do you check the analysis with all same option ?
Best regards
Philippe

EmptyPoints behaviour is not consistent

I am using RDLC in asp.net. The behavior of the empty points is not consistent. Sometimes it draws a line and connects the empty points and sometimes it skips the line. I don't want to connect two points when the in between data does not exist. Please
help me to solve this issue. Thanks.
mub

Hi Mubashar,
According to your description, you have a line chart including empty points in your report. Now you find some the empty points are kept in the line, but some empty points are skipped in the line. Right?
In Reporting Services, when working in a line chart, if our dataset includes empty values, the line chart will add empty points, in the form of placeholder lines, in order to maintain continuity on the chart. So those empty points supposed to be kept in
the line chart. In this scenario, we can hardly find out the possibility which cause your problem. But for yourself testing, you can change the type into column or bar chart to see if the data is displayed properly. If possible, please post some information
about your dataset or some screenshot to us. That may help us reproduce your issue in our local environment.
Reference:
Line Charts (Report Builder and SSRS)
If you have any question, please feel free to ask.
Best Regards,
Simon Hou

Line rate is higher than attainable rate!

I've been on Infinity for 3 or 4 months now and have had consistently a BT profile of 72.3 to 72.86Mbps, the changes occuring after modem resets or power cycles. Attainable rate (via the standard modem hack) has been 75272 to 76184kbps. Line rate has been 500 to 900 kbps below the attainable rate.
A few days ago we had a major power cut in the local area including here, lasting for several hours and afterwards, everything worked as normal. Just now I decided to check my BT profile and modem stats, just out of interest, as you do. The results are interesting - my profile has gone up to 75.73/20.00 and the modem stats are what I thought was impossible - line rate is much higher than the attainable rate! Stats are below.
Line is stable and needless to say I am delighted - I am now getting speedtest d/l results 3Mbps higher than ever before (74Mbps), but can anyone explain how line rate can be above attainable rate?
Mode    VDSL2
Traffic type    PTM
DSL synchronization status    Up
DSL up time    272927
   Line Status
    Downstream    Upstream
Attainable rate (kbit/s)   75948   26179
SNR margin (dB)        5.4      15.1
Line attenuation (dB)      0          0
Output power (dBmV)         13      3.8
   Statistics
      Downstream    Upstream
Line rate (kbit/s)   78235    20000
CRC errors      0             0
FEC errors               981       178
HEC errors             2182    0

You must have a good line and probably have the cabinet in your front room!
Who knows! I wouldn't say it would be impossible to hit pass your attainable rate, i would only take these as estimates as much as everything else.
It was like when i was on copper, thinking my line could only sync at 4MB, but constantly synced at around 6.5-7MB which was good for me! lol!
If you want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side If the the reply answers your question then please mark as ’Mark as Accepted Solution

WS-X6704-10GE at line rate ?

Hi..
Any idea if the 4 port 10GE card WS-X6704-10GE runs at line rate for each port ? Can we get approx 40Gbps throughput out of this card ?
Eng Wee

Hi Eng wee,
The 4 port 10 Gigabit Ethernet interface module is CEF720 based and communicate using 40-Gbps connections to the integrated 720-Gbps switch fabric of the Supervisor Engine 720.
http://www.cisco.com/en/US/products/hw/switches/ps708/products_data_sheet09186a00801dce34.html
HTH,
-amit singh

Decent line rate, throughput not consistent!

Similar Messages

Maybe you are looking for