Decentral Adapter not showing up in RWB

I have just installed a J2ee Decentral Adapter instance, configured the exchange profile to connect back to the main PI instance and connected it to the SLD (both the J2ee Decentral Adapter and main PI instance use the same SLD).
One of the last steps is to check see if the Decentral Adapter shows up in the PI Instances Runtime Work Bench (RWB), but it does not.
I've noticed that on the SLD, the J2ee Decentral Adapter shows up as a Technical System, but when going to the SLD > Administration > Content Maintenance > All Instances > Class: XI Adapter Framework, that only my main PI instances show up, not the recently installed J2ee Decentral Adapter.
Anybody have any ideas of what else to check ?
Thanks..SB

Aaron,
1.1 SAP XI AF CPA Cache are set at the defaults of the install. The SLDAccess is set to true which according to the following SAP Help doc says that the entris are ignored: http://help.sap.com/saphelp_nw04s/helpdata/en/29/22ee41c334c717e10000000a155106/frameset.htm
1.2 SLD DATA Supplier is set correctly. I can do a CIM Test and trigger the data upload successfully. Still no entry under the Content Maintenance though.
2. SXI_CACHE > Adapter Engine still does not show the Decentral Adapter. I've even bounced both systems and the SLD.
per Chirag I've also double checked blog "Basic Steps In Decentralized Adapter Engine
This Decentral adapter is in DMZ #1, so I must use the IP of my SLD for the SLD access and my Main PI is in DMZ #2. I've checked to make sure ports 50000 and 3300 from Decentral to my PI system work - are there any other ports ?
Thanks...Scott B.

Similar Messages

Sender File Adapter Not Showing in Decentral Adapter Engine

Hi,
We have recently implemented a Decentral Adapter Engine on a windows box. The adapter engine seems to be working fine because my adapters show and seem to work fine in it.
However, when I define a Sender File Adapter that uses File Content Conversion message protocol instead of just File messaeg protocol, the adapter does not show up in the decentral adapter engine.
I made sure that Adapter Engine parameter in the Sender File Adapter shows the new adapter engine but that does not seem to be working. If change the Adapter Enginer parameter to show the Central Adapter Engine, then I can see the Sender File Adapter on the Central Adapter engine and it works fine. (Note: The Central Adapter Engine is installed on a Unix box)
Here are the paramters I defined for the Sender File Adapter:
- Transport Protocol: File System (NFS)
- Message Protocol: File Content Conversion
- Adapter Engine: (new Adapter Name)
Source Directory: (
server/drive/path)
File Name: purchaseOrder.txt
Quality of Service: Exactly Once
Poll Interval (secs): 60000
Poll Interval (msecs):
Retry Interval (secs):
Processing Mode: Archive
Add Time Stamp (checked)
Archive Direcotry: (
server/drive/path/archive)
Process Read-Only files: (not checked)
Processing Sequence: By Name
Fiel Type: Text
File Encoding:
Operating System Command:
Additional Files (not checked)
Content Conversion Parameters
Document Name: MT_Request_File_Data
Document Namespace: http://nxy.tots/fg_admin
Document Offset:
RecordSet Name: Purchasing
RecordSet Namespace:
RecordSet Structure: Purchase_Record,*
RecordSet Sequence: Ascending
RecordSets per Message: 1
Key Field Name:
Key Field Type: String(Case-Insensitive)
Purchase_Record.fieldFixedLengths: 8,4,2,10,10,12,18,12
Purchase_Record.fieldFixedType: char
Purchase_Record.fieldNames: Request_Action,Request_PO_Num,Request_PO_LN,Request_PO_Date,Request_Purchasing_Org,Request_Purchasing_GName,Request_Created_By,Request_Vendor_Name
Purchase_Record.fileContentFormatting: trim
Adapter Status: Active
Advanced Mode: (not checked)
Your help is much appreciated.

Hi Alaa,
look into this document:
http://service.sap.com/nw-howtoguides -> Exchange Infrastructure -> Troubleshooting: Adapter Engine 3.0 (Expert Call slides)
If the File Adapter works without conversion, then you should count the number of fields in a row. If it differs from the configuration, then it runs on error.
Another idea is to check the content type of the file. When you do not enter a File Encoding, then the file adapter assumes utf-8. If the file is for example latin-1, then the number of characters in a row are not counted correctly.
Regards
Stefan

File Adapter not showing in Adapter Monitoring

I have created a basic scenario and when I go to check the file adapters they are not showing... Why is this what should I do

Hi Ricardo,
Please check the adapters in RWB...Is the File adapter is avialble or not?
If you can able to see then it should get appear in the Adapter list otherwise please deploye the the adapters once again.
Please let me know if you have any queries.
Regards,
chandu.

Xpower ac adapter not showing in device manager

Help!!
this is my third board and have just reassembled this board yet again trying to get the Bluetooth/wifi adapter to work yet again.
The adapter is not showing in board explorer or device manager. I have reseated this numerous times and have tried a different adapter with zero luck. I sthere a bios setting to enable this? I am currently using bios 1.5.
Any help would be greatly appreciated

BIOS->Advanced- see if there is tab like Intel Ethernet ........... Go into it if it is there, and see if it shows if adapter is connected or not (Not link connection as this will bne disabled)
Take adapter out and see if it has bent pins, as this might bre causing the issue. If all fine, get it bnack into the slot for it and take motherboard out of the case and test on non conductive material (motherboard box is ok, NOT Anti conductive bag). Also >>Posting Guide<<, and you could also try second BIOS (little switch, flip it when PC is OFF)

Wireless adapter not showing up in device manager

Hello all,
I am having a particularly frustrating problem. I was playing around with the memory timings to overclock my computer and all of a sudden, my wireless adapter ceases to exist to my computer. It does not show up anywhere in device manager (including no unknown devices or anything), only the Ethernet shows up. I have tried a system restore, turned off all OC and my BIOS is updated to the most recent version. Is it possible that trying to overclock my computer caused the wireless adapter to burn out? The motherboard I'm using is the msi x99S gaming 9 ack.
Any help would be very appreciated, thank you all in advance for your time to help out!

remove power cord from the PSU and >>Clear CMOS Guide<<
if the wifi card is removable, try to reseat it
also install latest killer drivers from:
http://www.msi.com/support/mb/X99S-GAMING-9-ACK.html#down-driver&Win8.1 64
[try older version as well if needs]

HP ENVY Rove 20 - Network Adapter not showing after Windows 10 Upgrade

After upgrading to Windows 10 the Network Adapter does not show up. Verified in Device Manager that there is no issue and the driver is there. Removed the device from device manager, attempted to use a different driver, still no success.

MrDimplz wrote:
Really disappointed in HP for not being ready for W10 rollout. I upgraded my HP Envy desktop PC 700-214 and after the upgrade, I could not connect to the internet. Didn't recognize the networking hardware. Went to HP Support (on different computer) and found out here aren't W10 drivers yet for this machine. Very Poor.My wife has a Dell laptop and we have another older Dell that upgraded no problem. Why because Dell is on top of their $__t when it comes to this stuff.Won't by HP again.Did you not try to reinstall the last support Drivers into Windows 10 to see if it works? Also with the lastest Windows HP will probably not support redoing drivers for older system as that will be cost prohibited to do. And it will be up to the Endusers to find the right drivers and software that matches their system to work with Windows 10 assuming they work with Windows 10. As to Dell that is something only Dell can answer that question and since we don't know if this is Dell Consumer or Business product since this falls outside of HP forums to discuss. You can't expect to have drivers if your system is too old to support Windows 10.

Windows 2003 on T61 wireless adapter not showing

I have 7658( CTO) T61 with XP pro.... I downgraded windows 2003 enterprise edition SP2. i have few questions
1. I changed the bios to compatibility mode ( I keep sata then win 2003 not booting, so changed to compatability mode). Is it required that I keep compatability mode.?
2. Wireless adapter is not working ( not showing at all). It is PCI\VEN_168C&DEV_1014&SUBSYS_058A1014&REV_01\4&29E2C51B&0&00E1
I downloaded and tried many drivers from lenovo website but is not working.
I have struggled for a week and searched many forums but nothing is helping me out. Please help me.

You will need the Windows 2003 compatible SATA drivers to stop using compatibility mode. I don't know if they exist... good luck there. Try Intel's web site since you probably have an Intel chipset.
As for the wireless adapter, again it may be a matter of Win2003 not recognizing the device. I would try and manually install several drivers and see which one may work. You may have to force-feed Win2003 since it doesn't recognize the hardware. Be sure you know the manufacturer of the wireless chip... Intel or Broadcom or Atheros? Look at the specs for your laptop.

Jpr adapter not showing in adapter type while creating communication channe

Hi all,
I got error in JPR adapter type.Due to that its displaying in adapter type while creating communication channel.I checked in RWB in communication channel monitoring its showing
Error getting JPR configuration from SLD. Exception: No entity of class SAP_BusinessSystem for EXI.SystemHome.hexsap found
No access to get JPR configuration
How to solve this issue,
Regards
Vijay

Thanks guys for the response..
I checked the IR and the SAP Basis has been added. Here are the details I got.
Name: SAP_BASIS
Version: 700
SWCV: SAP BASIS 7.00
Available Support Packages: 12
Any more suggesions/feedback will be greatly appreciated.
Thanks

Ralink Wifi Adapter Not showing

My device manager doesnt show my Ralink wifi adapter. When i click on view hidden devices, i can see it there but it says Code 45 error, hardware not connected. Why is this happening? Please help. Im unable to use wifi on my device because of this!

Hi @yashagarwal ,
Thank you for visiting the HP Support Forums and Welcome. I have looked into your issue about your HP Pavilion g6-2314ax Notebook and having issues with the Wireless drivers. Here is a link to the HP Support Assistant. Just download and run the application and it will help with the software and drivers on your system it has built in Wireless troubleshooting assistance.
Here is a link to the troubleshooting the Wireless connection.
Here is a document on Airplane mode.
If Airplane mode is on you cannot use your WiFi and you would see the code 45 not connected, so Airplane mode should off and no Ethernet cable connected for the Wireless troubleshooting.
I hope something listed here helps you.
Thanks.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom to say “Thanks” for helping!

Wireless adapter not showing any available networks

I've recently discovered that my Intel Centrino Advanced-N 6235 wireless adapter in my Asus Zenbook UX32VD running Windows 7 64 bit is not working as it won't show any available networks while my phone can find plenty in the same area.
So far I've:
-Re-installed the driver. Before I did this the adapter wouldn't even show when trying to change adapter settings. When I looked at the adapter in device manager I found an error code 52 which disappeared after I re-installed the driver.
-Re-installed the client for windows networks installed for the adapter which did not make a difference.
-Temporarily turned off my AVG-free anti-virus which did not make a difference.
When looking at the adapter after clicking change adapter settings in the networks and sharing center it says it's not connected, but as stated above it doesn't show any networks to connect to.
Also, when I try to use the networks diagnostics tool I get the following error message:
Windows cannot find
'::{26EE0668-A00A-44D7-9371-BEB06...\resultPage?keywords=+Network;NetworkDiagnostics'.
Make sure you typed the name correctly, and the try again.
Any possibly solutions I've not already tried are welcome. Thanks in advance for any help.

Hi,
Locate to Services and check all services relating to wireless and network are enabled: Wireless Zero Configuration and WLAN AutoConfig, etc.
Also, make sure your NIC is working correctly from device manager.
http://kb.linksys.com/Linksys/GetArticle.aspx?docid=108496d0924847afaf9c4a7bb72110b5_5646.xml&pid=80&converted=0
Have you tried manually connecting to wireless?
http://kb.linksys.com/Linksys/GetArticle.aspx?docid=8fd9ee85a0bf42f0986ed23390be8c66_19850.xml
Andy Altmann
TechNet Community Support

2ndary display adapter not showing up

I am trying to get 2 monitors simulataneously, using the internal VGA bult into the motherboard as primary, using the 15 pin connector to an lcd screen, and an nvidia-vanta-tnt2 agp card as the secondary adapter to a 19" analog monitor. By modifying the init-adapter in the bios, I can get either one to work alone, but I cannot get winXP to recognize both adapters at once. There are no cards in the computer aside from the AGP card. Anyone have any suggestions??

You can't do it. The only way to do that is if you have a radeon 9100 IGP chipset and a radeon card. That's th e only way you can do that. Onboard video and video cards will not mix.

Virtual network adapter not showing as domain network

Hi
I've got a Windows 8.1 machine that is connected to a domain on the LAN.
Before I installed Hyper-V the network showed up as "Domain Network" in the network and sharing center but when I installed Hyper-V I created a virtual switch (external) and since then the network has shown up as "Private Network".
This is on the Windows 8.1 host and the machine has full access to the LAN and the Internet and is using the domain for logins and permissions, which allows me to browse file shares on other machines on the network without having to sign-on. Most of the
time I'm not even running any virtual machines on the PC, I have Hyper-V for testing websites on different versions of IE.
The only problems I have are the network type not being detected correctly, my local firewall blocking lots of stuff I run on it (due to the firewall rules all being set up for a domain network) and also when I RDC to another machine it refuses to use saved
credentials as it can't identify the machine (I don't know if this is related to the domain network problem).
Has anyone any suggestions what could be going wrong or how I can diagnose the problem?
Thanks

Hi Mog00,
Could you please run command "ipconfig /all " and post the information here .
Maybe you can try "Troubleshoot Problems" in "Network and Sharing Center" to diagnose and repair network problems .
Best Regards
Elton Ji
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Mini display port hdmi cable and adapter not showing display on LG TV

Connected my macbook air up to my LG TV 32 inch, via mini displayport - adapter to HDMI and then HDMI cable to HDMI port on the TV.
the TV is detected on detect displays on the macbook - but the TV says no connection.
Does anyone have any idea why this isn't working?
I've tried both HDMI 1 and 2 ports on the TV and neither can detect a connection, although when first connecting it it did say "connecting" for about 5 seconds before cutting out.

Seems like many people are experiencing problems with connecting to a tv via mdp-hdmi adapter. I have the same problem connecting my newly bought macbook air to my 4 year old samsung 32 inch. Both screens goes blue and blinks. My mac recognise my tv though, it says samsung when I go to the screenmenu to change resolution.
I have tried two different adapters, the moshi adapter which Apple recommends and another one. Im experiencing the same problem with both.
I´ve kinda concluded that it has to be a software problem since my mac has started to act strangely after I tried making it work for 20 minutes.
Apple please fix -.-

MOVED: Wireless adapter not showing up in device manager

This topic has been moved to GAMING Motherboards.
https://forum-en.msi.com/index.php?topic=253761.0

remove power cord from the PSU and >>Clear CMOS Guide<<
if the wifi card is removable, try to reseat it
also install latest killer drivers from:
http://www.msi.com/support/mb/X99S-GAMING-9-ACK.html#down-driver&Win8.1 64
[try older version as well if needs]

Alert Configuration not showing up: Error 404

Hi, we engaged this issue some days now and we already checked some entries in this forum but altering doesn't show up in RWB!
So we already did:
1. Activated all services concerning Alerts (SICF)
2. added all user rules to the users in charge
3. checked notes 913858, 750287 etc.
we found sth. what we don't know if its right. When looking in exchange profile we edited the parameter com.sap.aii.rwb.server.centralmonitoring.r3.ashost in the fully qualified hostname. But when checking entries like com.sap.aii.ib.server.connect.webas.r3.ashost we only see the hostname - not fully qualified. so paremeters look like this:
com.sap.aii.rwb.server.centralmonitoring.r3.ashost = server02.domain.local
com.sap.aii.ib.server.connect.webas.r3.ashost = server02
Doesn't these parameters have to be in same structure?! So when we changed com.sap.aii.rwb.server.centralmonitoring.r3.ashost in server02 we could not sign on to RWB service with any user.
Can somebody help us on this issue?! We have to activate altering but its is not showing up in RWB at all!
br

hI,
Error: 404 Not Found
Description: The server has not found anything matching the Request-URI. No indication is given of whether the condition is temporary or permanent. The 410 (Gone) status code SHOULD be used if the server knows, through some internally configurable mechanism, that an old resource is permanently unavailable and has no forwarding address. This status code is commonly used when the server does not wish to reveal exactly why the request has been refused, or when no other response is applicable.
Possible Tips:- for HTTP_RESP_STATUS_CODE_NOT_OK 404
u2022 404 is an HTTP response code that indicates that the resource in question couldn't be found. Usually this is due to an incorrect URL, so it is better to cross check all URLs. Check pipeline URL in the SLD in the business system of the Integration Server For this go to SLD->Business System-><yourIntegrtaion Server>->Pipeline URL: It should be like this http://<host>:<port>/sap/xi/engine?type=entry Where host is the host name of the Integration Server and port is the HTTP(8xxx) port. To verify this in Integration Server you can do like this. Go to SXMB_ADM->Integration Engine Configuration->Choose Edit from Menu -> Change Global Configuration Data to switch to change mode. Then select System Landscape - Load Configuration. (This is not required always)
u2022 Check that the port really is the ICM HTTP Port and not the J2EE port i.e SMICM then menu GOTO --> SERVICES and check the port number for HTTP. It should be HTTP port
u2022 If the error is Page cannot be displayed, cannot find server in https configurations Check and correct the SSL configuration for the ABAP and the J2EE side of the system
u2022 If the error is because of integration server when using Proxy communications then check these. i.e SXMB_ADM->Integration Engine Configuration->Corresponding Integration Server enrty should be dest://<Http Integration server-Destination> Where < Http Integration server -Destination > is the RFC destination (SM59) of type HTTP connection (type H) to the Integration Server. In this case, host name, port, and path prefix are saved in the RFC destination.
Regards

Decentral Adapter not showing up in RWB

Similar Messages

Maybe you are looking for