Dedicated Gigabit link between v880s

I would like to set up the ge interface on two v880's to be a dedicated gigabit link between them. However, I am having problems getting the link up. Here are the steps I have taken (on both servers):
1. connected ge interfaces with 50/125 fiber cable
2. vi /etc/hostname.ge0
3. vi /etc/hosts
4. ifconfig plumb ge0
5. ifconfig ge0 inet 192.168.10.x netmask 255.255.255.0 up
Following this, I can ping the local interface on each server, but I cannot ping the interface across the fiber. Here is the output of my ifconfig -a:
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
eri0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet 10.0.100.33 netmask ffffff00 broadcast 10.0.100.255
ether 0:3:ba:44:b1:f4
ge0: flags=1000803<UP,BROADCAST,MULTICAST,IPv4> mtu 1500 index 9
inet 192.168.10.2 netmask ffffff00 broadcast 192.168.10.255
ether 0:3:ba:44:b1:f5
I notice that "RUNNING" is not present in the flags for the ge0 interface on either server. Should this be reason for concern. I have not done a reboot of the servers, but I don't think that should be necessary since these servers should have dynamic config.
Any ideas of what I am doing wrong?

If you are connecting the servers without a switch on oneof the server you need to reverse the connection.
regards

Similar Messages

Cannot Establish Gigabit Link Between Catalyst Switches and GSR Router

The GSR Gigabit interface is configured for no negotiation auto and the line protocol goes up when connected to the Catalyst switch.
The Catalyst switch port remains unconnected even when it is physically attached to the GSR router.

The flow control settings must match on both sides for the link to come up. It is highly recommended that you configure auto-negotiation to on for both devices. (Auto-negotiation is enabled by default on all Catalyst switches.) Otherwise, if you have a layer 1 problem, the link remains up and a unidirectional link will result.
The initial software releases that support Gigabit Ethernet on the GSR router do not support gigabit auto-negotiation.
The following command configures gigabit auto-negotiation on the Catalyst 6000/6500:
set port negotiation module/port disable|enable

Is it best practice to use a dedicated link between NX7K pair for keep-alive?

I have been using dedicated physical 10G link between pair of NX7k for keep-alive. Is it a best practice? It seems a waste of 10G ports because keep-alives does not need that much bandwidth.
I'm thinking just configure a dedicated VLAN interface in the default VRF, and have it routed through other devices (fir example 6509 core switches) for keep-alive. Has anyone done that before? The goal is not to use dedicated 10G ports for keep-alive.
Thanks a lot.

gwhuang5398 wrote:I have been using dedicated physical 10G link between pair of NX7k for keep-alive. Is it a best practice? It seems a waste of 10G ports because keep-alives does not need that much bandwidth.I'm thinking just configure a dedicated VLAN interface in the default VRF, and have it routed through other devices (fir example 6509 core switches) for keep-alive. Has anyone done that before? The goal is not to use dedicated 10G ports for keep-alive.Thanks a lot.
I agree that using a Tengig port for this purpose is not efficient. The whole idea of peer-keepalive is to have a way to avoid split brain scenarios in case of peer-link failure. For this reason the peer-keepalives should never cross the peer-link as it defeats the original purpose I just cited. Following are some viable options:
You can use the N7K management ports for peer-keepalive functionality. If you have redundant supervisors then make sure you use an external switch (OOB switch for example) to patch the management ports.
You can use dedicated interfaces just like you are doing right now but that would make more sense if you had Gig ports in my opinion.
You can run peer-keepalives inband but you need to make sure this traffic is never routed over the peer-link. It is considered a good practice to use a dedicated VRF for this purpose.
Atif

How to create database link between oracle and SQL Server

Hello Everyone,
Here i have Oracle Database 9i and SQL Server 2005 databases.
I have some tables in sql server db and i want to access from Oracle.
How to create a database link between these two servers
Thanks,

Thanks for Everyone,
I was struggle with this almost 10 days....
I created Database link from Oracle to SQL Server
Now it is fine.........
Here i am giving my servers configuration and proceedure how i created the db link...@
Using Generic Connectivity (HSODBC) we can create db link between Oracle and SQL server.
Machine (1)
DB Version : Oracle 9.2.0.7.0
Operating System : HP-UX Itanuim 64 11.23
IP : 192.168.0.31
Host : abcdbt
Machine (2)
Version : SQL Server 2005
Operating System : Windows server 2003 x86
IP : 192.168.0.175
Host : SQLDEV1
User/PW : sa/abc@123! (Connect to database)
Database : SQLTEST (exsisting)
Table : T (“ T “ is the table existing in SQLTEST database with 10 rows)
Prerequisites in Machine (2):
a)     Oracle 10g software
b)     User account to access SQL Server database (sa/abc@123!)
c)     Existing SQL Server Database (SQLTEST)
d) Tables (testing purpose) (T)
Steps:
1)     Install Oracle 10.2.0.1 (Only SW,No need of database) *(Machine 2)*
2)     Create a DSN where your windows Oracle 10g SW resides *(Machine 2)*
Control panel >> Administrative Tools >> Data Source (ODBC) >> System DSN ADD
You can follow this link also.....
http://www.databasejournal.com/features/oracle/article.php/3442661/Making-a-Connection-from-Oracle-to-SQL-Server.htm
I created DSN as
DSN name : SQLTEST
User : SA/abc@123! (Existing user account)
Host : 192.168.0.175 (machine 2)
Already I have 1 database in SQL Server with the name SQLTEST
You can create DSN with different name also (not same as db name also)
3)     Create a hsodbc init file in $ORACLE_HOME\hs\admin *(Machine 2)*
Create init<DSN NAME> file
Ex: initSQLTEST
Copy inithsodbc to initSQLTEST
And edit
initSQLTEST file
HS_FDS_CONNECT_INFO = SQLTEST    <DSN NAME>*
HS_FDS_TRACE_LEVEL = OFF*
save the file....@
4)     Configure Listener.ora *(Machine 2)*
LISTENER_NEW =
(DESCRIPTION_LIST =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = TCP)(HOST = 192.168.0.175)(PORT = 1525))
SID_LIST_LISTENER_NEW =
(SID_LIST =
(SID_DESC =
(SID_NAME = SQLTEST) *+< Here SQLTEST is DSN NAME >+*
(ORACLE_HOME = G:\oracle 10g\oracle\product\10.2.0\db_1)
(PROGRAM = hsodbc))
(SID_DESC =
(SID_NAME = PLSExtProc)
(ORACLE_HOME = G:\oracle 10g\oracle\product\10.2.0\db_1)
(PROGRAM = extproc) )
:> lsnrctl start LISTENER_NEW
5)     Configure tnsname.ora *(Machine 2)*
SQLTEST11 =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = TCP)(HOST = 192.168.0.175)(PORT = 1525))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = SQLTEST))
(HS=OK)
:> tnsping SQLTEST11
If No errors then conti….
6)     Configure a file *(Machine 1)*
Cd $TNS_ADMIN ($ORACLE_HOME/network/admin)
Create a file
$ vi TEST_abcdbt_ifile.ora
something=
(DESCRIPTION=
(ADDRESS=(PROTOCOL=tcp)(HOST =192.168.0.175) (PORT=1525))
(CONNECT_DATA=
(SID=SQLTEST))
(HS=OK)
$ tnsping something
$ sqlplus system/manager
Your connected to Oracle database *(machine 1)*
create database link xyz connect to “sa” identified by “abc@123!” using ‘SOMETHING’;
select * from t@xyz;10 rows selected.
Thanks,
Edited by: ram5424 on Feb 10, 2010 7:24 PM

Database link between the databases with the same name

Hi,
I need to establish a db link between two databases that are named the same way on two different servers.
server 1 has a database dev1 and server2 has a database dev1. The tnsnames on server2:
DEV1 =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = server2)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = DEV1)
DEV1_server1 =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = TCP)(HOST = server1)(PORT = 1521))
(CONNECT_DATA =
(SERVICE_NAME = dev1)
Can anyone let me know a way to create a database link between the two above?
Thanks.

Hi,
Am not sure what problem you are facing in creating a db link
create database link dev1_server1 connect to x identified by x using "dev1_server1"
create database link dev1_server2 connect to x identified by x using "dev1_server2"where dev1_server1 and dev2_server2 are the tns entry in tnsnames.ora file of server2 and server1 respectively.
Regards
Anurag

How to configure two links between switches SG300

Hello!
I have two SG300 serie switches and two Gigabit connection between them. How do I configured these two links to work toghether like a one 2 Gigabit channel?
thanks a lot.

Hi Angel,
I think what you are trying to do is called a LAG on the SG300. This option is located under the "Port Management" tab and you can manage which ports you want to be in the LAG under "Link Aggregation" and there you will see "LAG Management" where you can edit your LAG 1 with the 2 ports that needs to act as one 2 Gigabit port.
I hope that was able to help you as that is what I have gathered from your question. Please reply back if you still need more assistance.
Thanks,
Brian Ng

Link between Delivery and Sales Order Schedule Line

Hi Gurus,
I have a requirement in which i need to display quantity and amount at schedule line level and also the delivery and delivery item for each schedule line.
For example, if there is a sales order O1 and item 10 for which we have 3 schedule lines and 3 deliveries as well say D1, D2 and D3.
Report should be something like this
Sales Order    Item   Schedule Line    Delivery    Del Item   Confirmed Order Qty
O1                 10      1                       D1           10            5
O1                 10       2                      D2            10            5
O1                 10       3                      D3            10            4
How can i determine that a particular delivery corresponds to which schedule line of that saler order-item?
We have the link between delivery and sales order but is there any way that we can get the link of delivery at schedule line level?
Please help.
Regards,
Gaurav

Hi,
I suppose you must check with SD functional consultant and the post should also be in the logistics SD forum and not BI. But I suppose there is know specific link between the schedule line of SO to the Delivery. It is more like a bucket flow for ex.
Sale order   Item    Schedule line qty
SO1            Item1     Sch1            10
SO2            Item1      Sch2           10
Delivery Item QTy
DO1       IT1   15
DO2       IT1    5
In this case qty 15 is distributed over both SO1 and SO2, and SO2 ITem1 Sch2 has link to both the DOs
So I am not sure if you can establish a one to one link, please check with your SD consultants.
Regards,
Ashwin G

Is there a DIRECT link between SD schedule lines and delivery lines?

Is there a direct link (db table) between schedule lines on a sales order (VBEP) and the delivery lines (LIPS)?
Is there a function module to retrieve the data?
Example-
One order line with 3 schedule lines.
Each schedule line is for 2 units (total of 6 units).
Three deliveries made. 1st is for 2 units, 2nd is for 1 unit (backorder), 3rd is for 3 units.
You can use document flow (table VBFA) or examine the SD document in the delivery line (LIPS) and link the delivery line to the order line. The schedule line already references the order line.
I am using math to decrement the schedule lines used and make the link between VBEP and LIPS. It works fine. I need four records back....
1st schedule line for 2 units uses delivery 123
2nd schedule line for 1 unit (partial) uses delivery 124
2nd schedule line for 1 unit (partial) uses delivery 125
3rd schedule line for 2 units uses delivery 125
Like I said, it works. Just wondering if I missed a more direct link.

As far as Db link is concern , I dont remember exactly , but 3 years before I had written a report which see Sales order schedule lines and devilry note lines against sales order. If you see process wise. when ever you create PO ( production order you assign some qty using 101 movement type .. and against production order you also give sales order . When you do delivery ( run seclude run ) it delivers against that material number , its movement is 601 ...
but I remember theres a link between these tables, VBAP,VBFA AND VBEP , LIPS ... against every sales order you can see sales invoice ( VBRP,VBRK) and you can also see your delivery note number in document flow .
I hope thisll give you some guide line, as right now I can not tell you the exact business process but I remember I written a report in SD 4 years before , in which they required Delivery against production order and sales order ... One more thing you also have production order reference on delivery item number. ( field :Empst ) . I think in my project they were maintaining this field .
Thanks

Change or delete the docflow link between two existing documents

Hi All,
Is there any FM or soulution to change the doc flow link between two documents .
For ex .. i have document A and document B , and created a doc flow link from A to B , Now i have to change the succeeding document to C
I have tried to modify the doc link ,but its not working using crm_order_maintain.I thought of deleting the link between A and B and then create a new link Between A and C , but deletion of link bewteen A and B is also not working.
I have checked with FMs CRM_DOC_FLOW_DELETE_CHECK_EC and CRM_DOC_FLOW_DELETE_EC, followed by CRM_ORDER_SAVE AND COMMIT . i could not find any exception from this FMs , but still the doc link is not deleted.
Pls share if you have any suggestions.
Regards,
Nithish

Hello
I wrote a report to delink items from document flow. I uploaded it [here|http://wiki.sdn.sap.com/wiki/display/CRM/Removelinksfromdocumentflow].
Please, use with caution and always perform careful tests before you run it in a production envinronment.
Hope it helps
Joaquin
Edited by: Joaquin Fornas on Nov 15, 2011 11:49 AM

How can i create link between ipad(xcode) and webserver?

Hi, I'm a new to iPad development and i need help,
i'm not good with english but i try to explain my question:
how can i create link between ipad(xcode) and webserver?
(the webserver ".NET" with driver odbc is connected with DB Oracle)
so, how can my ipad application access to the Oracle DB?
Create a webservice (.NET) to be place between iPad and DB, is this correct?
how can i do it?
which are libraries to include in the xcode's framework?
thx

I think the following URL will be your best answer:
http://stackoverflow.com/questions/3510468/connecting-iphone-to-an-odbc-database

Link between Invoice and Payments

As I understand the link between the A/R Invoice table and the Incoming Payment table is OINV.ReceiptNum = ORCT.DocEntry. My question is when does the ReceiptNum field get filled in? We have many closed Invoices that have a payment linked (viewed by going to Applied Transactions when on the Invoice) but the ReceiptNum field is still NULL in the database. Shouldn't these invoices all have a linked payment if they are closed?
Regards,
Jeremy

Hi Steven,
The reciptnum field is populated when the payment is created and the Invoice is a part of that payment. If you do a manual reconciliation this field is not populated.
Open the payments that you see in Applied transactions to see if the Invoices are in the rows.
Hope it helps,
Jesper

One to One link between VBRP items and BSEG items

Hi All,
I am working on a program where I have to link between VBRP table items against BSEG table items.
But in BSEG, the invoice items are summarised based on Material Number, profit center etc..
Is there a way to divide them, like any other table which holds the data transferred to accounting from sales exactly as it is in the invoice tables (VBRP).
If there is no such table, can any one help me figure out a logic where I can didvide the items of BSEG table exactly like the items of table VBRP.
Any help or input will be very highly appreciated.
Thanks in advance
Phani

Thanks for the Replies Ramani and Monika...
I alraedy have a relation between the Accounting Doc and Billing Doc (VBRP-vbeln to BSEG-belnr).
what I am looking for is the Item wise one to one mapping.
i.e Assume that we have 4 items in VBRP under one Billing Doc....
2 items have Similar Materials (Assume XYZ) and same Profit center (eq..MNO123)
and the Other 2 items have material (ABC) and Profit center (PQR6789).
Now these appear in Bseg as only 2 items, all the items with similar materials, profit center etc will be clubbed in Bseg (While Accounting). I.e In BSEG you will only find 2 entries for the above 4 items of VBRP.
I need to divide the data that I am getting from BSEG exactly as they are in VBRP.
Pls suggest if you know of any table where I can find this.....If not a table.., then a way to figure out the division of these BSEG items exactly as the VBRP items.
Brgds
Phani

FAX Sending - Link between SOST items and PO Data

Hi all,
We have a message type to send FAX to the vendors.
This is tracked in SOST.
There are some FAXes which get failed and are to be tracked individually in SOST.
We need to make a report which gets all the failed PO #s.
We are not able to arrive at the db link between the items in SOST and the PO data.
Can anyone of you let us know how this can be done ?
Thanks in advance.
Regards,
Vivek K

Thanks for the Replies Ramani and Monika...
I alraedy have a relation between the Accounting Doc and Billing Doc (VBRP-vbeln to BSEG-belnr).
what I am looking for is the Item wise one to one mapping.
i.e Assume that we have 4 items in VBRP under one Billing Doc....
2 items have Similar Materials (Assume XYZ) and same Profit center (eq..MNO123)
and the Other 2 items have material (ABC) and Profit center (PQR6789).
Now these appear in Bseg as only 2 items, all the items with similar materials, profit center etc will be clubbed in Bseg (While Accounting). I.e In BSEG you will only find 2 entries for the above 4 items of VBRP.
I need to divide the data that I am getting from BSEG exactly as they are in VBRP.
Pls suggest if you know of any table where I can find this.....If not a table.., then a way to figure out the division of these BSEG items exactly as the VBRP items.
Brgds
Phani

Link between Material Document number & Accounting document number

Hi All,
For material document there is a corresponding accounting document number generated.However this is not the rule in all cases.
Where is the link between the two(Material Document & Accounting Document) ?
In other words i want to list those material documents only, for which accounting documents are generated.
Regards
Piyush Kothari

STEP 1
SAP query way to extract your information.
Create an infoset SQ02 with a single table MKPF. (include key fields in the field group)
Step 2
From Extras
Create an additional field called zawkey (like bkpf-belnr) which will concatenate the MM document number MKPF-MBLNR and MKPF_MJAHR. The sequencing shall be number 1.
You may use this code below and paste also (this needs authorization as well)
data: zzawkey like bkpf-awkey.
clear: zawkey, zzawkey.
concatenate mkpf-mblnr mkpf-mjahr into zzawkey.
zawkey = zzawkey.
Add another field called ACCDOCNO (accounting documnet number) with sequencing number 2 with following code.
data: zaccdocno like bkpf-belnr..
clear: zaccdocno, accdocno.
select belnr from bkpf into zaccdocno where
bukrs = ccode and
GJAHR = MKPF-MJAHR and
awkey = zawkey.
endselect.
accdocno = zaccdocno.
Step 3
Include the additional fields into the field group.
Step 4
Click on the selection tab and create a parameter called ccode with a description Company Code and against
LIKE BKPF-BUKRS
Extras OBLIGATORY
Step 5
Click on the selection tab and create a seelction criteria pdate with a description Posting Date for the field MKPF-BUDAT
Extras OBLIGATORY
Step 6
Save, Generate and assign the infoset to a user group.
Step 6
Create a SQ01 query under the usergroup with all the fields in the infoset. and Execute. Enter a company code and one date of a working day where you expect material transactions.
The result will be all the material documents and their corresponding accounting documents, if available. If you want to see only those material document that do not have corrsponding accounting documnet, then while you are in the selection screen say accounting document number is not equal to blank.

Link between Ivnoice A/R (OINV) and Ivnoice A/P (OPCH)

Hi!
Is it possible to find some link between Ivnoice A/R (OINV) and Ivnoice A/P (OPCH) without using batches, serial numbers and UDFs?
Any ideas?
Thanx!
Regards,
David

Hi David,
I only known of 1 link possibility.
If you created the purchase order from the sales order (and the invoices are based on the orders) you can find the purchase invoice through the Purchase order, Sales Order, Sales Invoice.
Regards
Ad

Dedicated Gigabit link between v880s

Similar Messages

Maybe you are looking for