Default beacon/dtim settings

What are folks thoughts regarding increasing the beacon interval as well as the dtim interval on a very large byod data ssid? I know the dtim increases for voice but I'm interested in upping those settings on regular data ssid.
Sent from Cisco Technical Support iPhone App

If you can sniff the traffic you may want to look at the "QBSS" to see change utilization. Also you can check the beacon to make sure they are getting spit out even 102.4ms. The AP has to content to send it out, so if it the medium is busy you'll see delayed beacons. Though after so many delayed beacons will give itself better chances to access the medium (I forget the details)
Disable load balancing and band select. those are hacks.
In CPI you can run channel utilization reports. This will help you see airtime use
In 7.2 they added a way to limit users per radio. I'd set the 2.4GHz fairly low. This will help move dual band client over to 5GHz. It does run the risk of 2.4GHz users not getting access. In 7.4 you can enable AVC and watch traffic patterns. Give proiaty to the important class stuff and BE the unimportant stuff like facebook etc.
You may want to set up two SSIDs, a fast and a slow. Make the fast SSID 5GHz only. Users that can see it join it instead of getting on the 2.4 radios. Also I'd make the 5GHz 40MHz, this will allow clients that support it use less airtime. Make sure you select your 5GHz channels to match a large % of what you clients support. If only 10% of your clients support unii-2 extended... well don't enable those channels.
CCNP - Wireless
CWNA and CWAP

Similar Messages

Do you change the default RAW conversion settings?

I have used Sony (and formerly used Panasonic MFT) cameras (a900, a850) for two or three years and never had any reason to change the default RAW conversion settings. Five weeks ago I started using Sony's new a77, and for the first time am not satisfied with Aperture's default RAW conversion. (I recalibrated all my monitors -- twice -- thinking that something in my color workflow had got busted.) The default a77 RAW file conversion results in an overly-saturated, "Disneyfied" picture. I have found that by sliding "Boost" almost to zero, and cutting "Hue Boost" by half, I end up with a much more life-like, atmospheric, picture -- and one that closely matches the default rendering of RAW files from the a850 and a900.
1. Do you change the default RAW conversions settings? Why?
2. To what units, specifically, do the scales of these controls refer?
3. It seems that Hue Boost provides a range of settings that corresponds to the print settings "Perceptual" (= zero hue boost) to "Relative Colorimetric" (= full hue boost); does that make sense?
The User Manual, as usual, provides a solid concise explanation of the RAW Fine Tuning Brick.
Any experience you can share is appreciated. Thanks.
(Added:
(It seems conceptually wrong to me to have these controls be part of the RAW converter. Are there other adjustments in Aperture that do the same thing?)
--Kirby.
Message was edited by: Kirby Krieger

William -- many thanks for your help. I will almost certainly change the default for my a77 (as well as for the Nex-7 I used for a week).
Are there is any other adjustments mathematically similar to the "Boost" or "Hue Boost" sliders in the RAW Fine Tuning Brick? I ask for two reasons:
- Mostly I'm just trying to figure out what they do, and strengthen with knowledge my quiver of Aperture effects. According the the User Manual, they change the overall contrast, and the amount to which the hue is changed as the overall contrast is increased.
- In practice, it makes sense to me to have the RAW conversion produce the "flattest", least "effected" image possible -- to leave _aesthetic_ adjustments to me. I don't want to use the RAW Fine Tuning controls as part of my workflow; I want to know how to get the same increase in contrast and control of hues using other adjustments (that, specifically, don't require de-mosaic'ing). Apple seems to indicate that the use of the RAW Fine Tuning controls may be the best approach:
For images that consist of saturated primary and secondary colors, such as an image of flowers in a lush garden, shifting the hues to their true values has a desirable visual effect. However, this is not visually desirable for images containing skin tones.
The implication is spelled out in the sentencesthat follow: use the max setting for flowers, and the minimum setting for portraits. Isn't it odd that this recommendation is left to the RAW converter, and is buried deep in the User Manual?

Default Optimize Image Settings?

How do I set my own default optimize jpeg settings for Image Preview in Dreamweaver CS5? Whenever I open the Image Preview window, quality is set to "82" (see image). I have already optimized my jpeg files and want them to be inserted at "100" automatically. Otherwise, transferring an existing site with over 2,000 jpegs into Dreamweaver will mean I have to reset the optimization over 2,000 times (once for each image)!

OK - I get it. Don't open the panel, don't get FW! I'm relatively new to DW, so am finding my feet. Thanks for your help.

Default Noise Reduction Settings

HI, i upgraded from Digital Photo Professional 3 to 4, and it looks like the "Default Noise Reduction Settings" have been removed from preferences. Is there any way to achieve a default luminance and chrominance settings of 0 in DPP4?
Thanks!

I don't think so. There is nothing in the manual about, and like you, I can't see a way in preferences.
John Hoffman
Conway, NH
1D Mark IV, Rebel T5i, Pixma PRO-100, MX472

How do go back to my default display color settings? Just bought Spyder 3

Hello out there in Genius land...
I just purchased Spyder 3 Pro to calibrate my display monitor, but in order to do this correctly, I need to go back to my default color display settings.
I have manually calibrated my display several times in the past in the advanced mode, so I am familiar with this process, but I am unable to figure out how to go back to the default. Can't find a default option in the color settings tab.
Any assistance in this matter would be greatly appreciated.
Thanks,
Anneita

Thank you for your quick response.
I just checked mine since I never changed it. It shows I have two default color >displays - Color LCD.
When I select either one, the "Delete Profile" button is grayed out. This would >indicate to me that you should also still have your "default" color profile >showing.
Hmmmm....
Good point about the grayed out "Delete Profile" button. I went back into my "Color" tab to check it out, and I have 4 different profiles listed:
- 12-30-10
- 7/29/08
- Color LCD
- Color NTSC (19530 Calibrated
When I click on each of them, they show a totally different display color.
The only one that the "Delete Profile" button is not grayed out is 12-30-10, which I made on that date. The other 3 delete buttons are grayed out. But I am thinking that my actual default may be the one that says "Color LCD" like yours.
Is that safe to assume? What do you think?
Thanks,
Anneita

AirPort Express - Keeps Defaulting to Factory Settings

Hi everybody:
I just got an AirPort Express to broadcast my broadband internet throughout my apartment.
I connected it to my cable modem by ethernet cable, created a new network in Airport Utility, and it set up just fine.
I noticed that the light on the Airport Express was flashing amber, although in the A.Utility, it showed green with a successful connection.
The Airport Express is placed directly next to my computer.
Everything was working great (for a while), and I was even able to set up another Airport Express on that same network to broadcast AirTunes in another room. That connection was successful, and the light on Airport Express #2 glowed green.
After a few hours however, I lost connection.
And in Airport Utility, the status on Airport #1 (the one used to create the new network & connected by ethernet to my modem) showed that it had been defaulted to factory settings.
I then manually reset both Airports to default settings, set up the whole configuration again by creating a whole new network, and everything worked as before (#1 flashing amber, but status good in A.Utility; #2 glowed green), but again, after a few hours lost connection #1 status showed default factory settings.
There's a good chance that I'm doing something wrong -- any ideas?
Any wisdom is greatly appreciated.

Usually, if you have an amber light on the Express, there's also an amber light in AirPort Utility when you check the settings.
Click on the word "Status" to see if there are any messages in the window that opens. A flashing amber light can sometimes be a message that a firmware update is available for the AirPort Express.

I purchased my imac in the United States and now I live in the United Kingdom. How do I set the computer to know where we live as it defaults to US settings and I am having trouble registering my iphone

I purchased my imac in the United States and now I live in the United Kingdom. How do I set the computer to know where we live as it defaults to US settings and I am having trouble registering my iphone. I had used it in the US for two years.

You're Welcome..
See Here for
Changing Account Information
http://support.apple.com/kb/HT1918
Changing iTunes Store Account
http://support.apple.com/kb/HT1311
Apple ID FAQ
http://support.apple.com/kb/HE37

CHANGE DEFAULT NAME/SECURITY SETTINGS = LOWER CONNECTION SPEED

I have a Linksys WirelessN Router--If I use the router with all of the default settings I can achieve cable speeds of 300mbps. Fantasically fast!!! As soon as I change the name of the router from "Linksys" to any other name, my speed drops back down to 54mbps. I also changed the security settings to "PSK Personal" and added a personal password so my system wouldn't get "hyjacked." Any thoughts?

Hi… logon to router’s setup page, try changing Radio band to wide 40MHz, wide channel to 9, standard channel to 11, go to advanced wireless settings reduce beacon interval to 50, fragmentation and RTS threshold to 2304, change N Transmission rate to 270MBps…wireless security should be PSK personal, also try upgrading latest firmware on router, check whether it makes any difference or not.

How do i restore default text/font settings for fire fox?Text is not displaying correctly some letters not dark and see odd characters inplace of letters in words

How do i restore my text so that all words are uniform in darkness?Now some letters are fragmented or missing a part of it and see odd characters instead of letters in some sentences.Ive tried different fonts in the Options still the same.Would like to
be able to restore my default settings for text/fonts.Would that eliminate this problem?

Try to set the Boolean pref gfx.font_rendering.directwrite.use_gdi_table_loading to false on the about:config page.
To open the about:config page, type about:config in the location (address) bar and press the "Enter" key, just like you type the url of a website to open a website. 
If you see a warning then you can confirm that you want to access that page. 
*Use the Filter bar at to top of the about:config page to locate a preference more easily.
*Preferences that have been modified show as bold (user set).
*Preferences can be reset to the default via the right-click context menu if they are user set
*Preferences can be changed via the right-click context menu: Modify (String or Integer) or Toggle (Boolean)

Column not showing up in Change Default Column Values settings

There is a column that appears in the view without a problem but we are not seeing the column in the Library settings "Columnd Default Value Settings" We see other similar columns (single line of text) from the same content type but
we are not seeing this one. I am not sure why and and not really sure how to start troubleshooting this. curious.
davidh

Seems strange issue, but i have few questions. What is the type of the column which is missing?
Is this content type is custom one and developed using Visual studio? do you see the same behavior when you try to create from UI(I think you should see same behavior)? did you try creating/developing the content type in other site template?
My Blog- http://www.sharepoint-journey.com|
If a post answers your question, please click Mark As Answer on that post and Vote as Helpful

Default transaction type settings

Hi,
When I try to select the transaction type from the locator with in order creation t code , where we can see only one custom defined transaction type ( user restricted one ) ,
Please suggest how we can do this custom settings for the particaluar transaction/screen.
Regards
Naren..

Hi Rhesa,
Thanks for your reply, here I would like to set the transactin code level not the user specific, means when you run the
CRMD_ORDER T code to create the orders and select the create option, where you will get only default transactin type .
Can you please provide any input inthis.
Regards
Naren..

Change default query display settings (show more cells)

Hello Friends!
I have a little issue with default display settings in the Bex Query Designer.
Can I change the display settings like in an analyses item e.g. more Number of Data Columns Displayed at once?
Thank you for your help
Best regards
Florian

You can also look at the following thread -
show more than 5 column in web analyzer

Set default page setup settings in adobe acrobat so adobe reader prints to tray 2 on my printer by default?

I want to set a tray on my printer to be the default for just adobe reader without setting the default for windows. When i set page setup settings it reverts to the defaults when i open new PDFs and i want this seetin to save.
Thanks

I would suggest creating a second instance of the printer in Windows with tray 2 as the default tray - select that printer from Acrobat.
Control Panel > Add Printer > Create the Printer
Control Panel > Printers > Printer Properties

Can I set by default some Aperture settings?

When I select Edge Sharpen it always appears by default the settings 50-33-66
I have two presets, one of them, the most I use I would like, if it were possible, to set it as default, so that when I open Edge Sharpen appear.
Is it possible?
Regards

First, an explanation about my name:
this is the mail I have received with the notification that I had an answer is this post:
guillermaolvares (what a name!)...
it is not possible to automatically apply your setting to every photo you load into aperture, however instead of clicking on the "enable" button of "edge sharpen" (which enables the adjustment with the defaults), you can select your preset straight away (clicking on the gear icon). this will enable the adjustment with your settings, and you saved 1 click.
My name is Guillermo Álvarez (William Alvarez) and when I registered I decided to write all together: "guillermoalvarez"
Done it that I only want to thanks the answer.
Regards.
Guillermo

How do I change the default ruler style settings

I'm very frustrated with the lack of margins in the default ruler settings in cocoa apps. I would MUCH rather have the ability to set my defualt ruler settings including margins, font, size, etc. rather than reset them every time I create a new document. Is this possible? How?
Thanks so much.
Varen

"Cocoa apps" is too broad a category - so the answer to that is "no". There's no system-wide setting for document formatting.
But you may be able to do it for individual apps if you tell us which ones you are using. And even if there is no way to set a preference for a particular app, in general you can create a blank document with the formatting that you want, save it someplace convenient, then in the Finder right-click it, choose "Get Info" and check the "Stationary Pad" option. Then whenever you double-click that document, you'll get a new document with those same settings.
That works with TextEdit, but you need to type a little bit of text for the new margins to stick (for some reason the margins reset to 0 if you leave the document blank).

Default beacon/dtim settings

Similar Messages

Maybe you are looking for