Default Host (DMZ) and Port Mapping together

Hi all,
I have the G5 set as a default host for all my web services through the Airport Extreme.
In the Airport Extreme's Port Mapping tab, a user is not prevented from using the port mapping tab even when the Default host is set. I want to serve video through another port not on the G5.
Does this mean I can set up port mapping for ports I do not want to go to the default host? (my G5 in this case)
I asked this on the airport forum and never got an answer, maybe you G5 folks might know. (Or maybe there is a setting that will redirect from the G5.)
Thanks in advance,
Jamy

I figured it out. I can't have a DMZ and separately port mapping on the Airport.

Similar Messages

Web service invocation problem on host hostname and port 8000 protocol : http logical port name : LP_WS_SMDAGENT_MONITORING

hello colleagues,
In the phase Connect Diagnostics dont show the Agent available in SLD, but when go to SLD i have the agents,
Error,
Connect Diagnostics Agent
The table does not contain any data
Agent availables in all SLD
SOAP:1.007 SRT: Unupported xstream found: ("HTTP Code 401 : Unauthorized")
Web service invocation problem on host hostname and port 8000 protocol : http logical port name : LP_WS_SMDAGENT_MONITORING
Thanks

OK, then pls follow below steps;
- Go to step 'Create Users' in solman_setup System Preparation scenario and make sure the user SM_INTERN_WS has a green status. Use the 'Test Login' button to make sure the user is not locked and has correct credentials maintained in solman_setup
- Immediately after checking the user status, navigate to Configure Connectivity->Enable Web Services and execute again the 'Create Logical Ports' automatic activity, in order to propagate the correct credentials to the Logical Port definitions.
- If the above operation is not successful, repeat the two steps above, providing a different user Id in 'Create Users' step, eg SM_INTERN_W1. This will prevent situations where the user gets locked by Logical Ports using an obsolete password.
Let me know the results.
Regards,
Vivek

Replacing Host Name and Port number throughout Environments

So I am currently working on a project that have several classes using simple JDBC code. I'm switching all of it to use JNDI instead of what is currently being used. I'm using Weblogic and the plan is to have the code run in a cluster.
Here is a code Snippet of some of the code.
Context ctx = null;
Hashtable ht = new Hashtable();
ht.put(Context.INITIAL_CONTEXT_FACTORY,
"weblogic.jndi.WLInitialContextFactory");
ht.put(Context.PROVIDER_URL,
"t3://hostname:port");
My problem lies in the the "t3://hostname:port" String. I don't want to hardcode that since I know its bad code practice but my question is what is the best way to replace that with the Host Name and Port number as I move environments. Should I have a Class with a Static Variable and just reference that through the other classes or should I put it in some Property file and read the value from there? Any insight into this would be greatly appreciated.
Thank you.

would it be something like this?
Properties properties = new Properties();
          try {
     properties.load(new FileInputStream("src/jndi.properties"));
     String url = properties.getProperty("url");
     System.out.println(url );
     } catch (IOException e) {
     }

How to get the Host name and port number

Hi all,
I am working in xRPM. I need to get the server name, host name & port number for the portal and i need to diaplay as a link in the Workflow step. I cant give the portal link as static, as it will vary depends on the DEV, QUAL, PROD. Is there any FM or class is available, so i can get the server name, port no. for my purpose?.
Regards,
Vinoth

Hi Kanagaraja,
My client has configured the portal and backend in different stack. So when i execute the FM you provided and with class: CL_HTTP_SERVER, CL_WD_UTILITIES, i am getting only the backend host name and port no. not the portal's info. So please help is there any way we can get the portal's info.
Thanks for your reply.
-Vinoth

Getting host name and port number from application

Does anyone know how I would be able to get the host name
and port number from an application launched by java webstart ?
This is the host and port of the URL that this application is launched from.

A couple of suggestions:
-The note is about 6.40. Doesn't fit for your server
-Don't!
-Reinstall!
Regards,
Benny

Getting host name and port number from an application

Does anyone know how I would be able to get the host name
and port number from an application launched by java webstart ?
This is the host and port of the URL that this application is launched from.

A couple of suggestions:
-The note is about 6.40. Doesn't fit for your server
-Don't!
-Reinstall!
Regards,
Benny

Getting WLS host url and port number

Hello Experts,
I need to forward an authenticated request to JAAS LoginModule. How can I get wls host name and port numbe in the LoginModule?
Thank you in advance,
Thanks for reading my post

Hi friends.
I have used the last post, but it is not working.
Mat be the API had changed.
What class or interface could give me this data in web dynpro component?
Too, I'm using the SAP NetWeaver Developer Studio
Version: 2.0.16
Build id: 200602130353
Thank you.
Manuel Loayza
Living La Vida JAVA
Edited by: Manuel Loayza Gahona on Jul 23, 2008 6:54 PM

SMICM and WAS host name and port

Hi all,
Can someone please throw some light on the activity WAS host name and port in port... the question is:
Q. The information about host name and port is available in Tx SMICM, looking there in my case I find port 80xx whereas the portal runs on port 500xx. What value should we enter in the port field of "Connecting to a WAS system" in portal?
Is it what is given in SMICM or we should use 500xx?
Regards.

(80xx assuming you're starting Web Dynpro ABAP apps, integrated ITS and BSPs.)
Thanks Michael,
How about in case when it's not ABAP it's java apps i.e. when we are connecting BI to portal with SSO on dual stake. BI uses the 500xx port on FQDN and thus it's confusing me, whether to use 80xx or 500xx (when 500xx seems the port in use on BI portal).
Hope I made my point clear.
Regards.

ITS host name and port.

Hi Experts,
What is integrated ITS host name and port for portal services? Where can I find the ITS Parameters to create a SYSTEM in Portal?
Regards,
Amit.

Hi Amit,
GO to SMICM toce in R3 system and clcik on (F) servicess button , u will get ITS host path and port number .
GIve this details in System object ITS .
ITS host name : from SMICM
ITS path should be /sap/bc/gui/sap/its/webgui
Surekha.

NAT configuration and Port Mapping for xBox

I'm looking for help with port mapping to open up the NAT for an xBox One. I'm working with the following network devices:
xBox One
DSL Modem: Embarq (ZyXEL) 660R series
Airport Extreme version 7.7.3
I understand the following from researching the issue:
The default settings for both devices block the ports needed for xBox Live.
Airport Extremes are not on the compatible list for xBox.
Port Mapping is better then creating a DMZ for the xBox.
The xBox needs its own manually set IP address.
I switched my Network>Router Mode from Off (Bridge Mode) to DHCP and NAT. I then created a DHCP Reservation and the Port Settings for that IP.
After doing this, the Airport would restart and display a warning - Double NAT. I figured this was because the 660 settings showed the NAT Mode to be SUA Only. The Edit Details link displayed an empty table where you edited the SUA/NAT Server Set. I switched from NAT Mode>SUA Only to None. So there was my Double NAT and I would have thought that would have removed one.
I also disabled the Firewall and Enabled the UPnP.
After restarts the Airport continued to display the Double NAT error. However, with the 660's NAT Mode set to None, the Internet was not there. Web browsers and email accounts replied with server not found.
Only with the 660 set to SUA Only and the Airport in Bridge Mode is the Internet accessible. I now have the details for the SUA filled out for the xBox's IP address and ports.
Hypothesis
Since both devices are acting as DHCP servers the port mapping is not working. Rather then have the 660 distribute IP addresses and then having the Airport distribute another range of numbers, I need to have both devices bridge and distribute one range of numbers. Currently the 660 is using the 192.168 range and the Airport is using the 10.0 range.
Am I correct? Any thoughts and suggestions are welcome.

Port forwarding through a double NAT.. is near impossible.. !!
And the xbox is so attuned to using UPNP it is very hard not to.. even port mapping is not a great fix. Since apple decided gamers did not count as users for Airports.. I think honestly it is best to bypass the airport and stick to upnp from the modem router.
What method of authentication does your ISP use? Because it is really better to use one router.
And in fact the router should be the Zyxel. If you plug the Xbox to the Zyxel running in full router mode, with the airport removed from the network does it work and open NAT??
If not replace the Zyxel with a modern listed router that is xbox compatible and bridge the airport to it.

How to get Host name and port inside UDF

Hi,
I want to access the Host and port in UDF to pass it to a link http://host:port/AdapterFramework/ChannelAdminServlet?party=&service=&channel=*&action=status dynamically.
How can I acieve it?
Manisha

Hi
With this code. I am getting error:
try
java.net.InetAddress addr = java.net.InetAddress.getLocalHost();
String host = addr.getCanonicalHostName();
catch (UnknownHostException e){}
if (ProcessMode.equals("P"))
try{
String xyz="/AdapterFramework/ChannelAdminServlet?party=&service=&channel="Name"&action=stop";
URL server = new URL("http", host, 8XXX, xyz);
tring userPassword =Userid + ":" + Password;
   String encoding = new sun.misc.BASE64Encoder().encode (userPassword.getBytes());
    URLConnection uc=server.openConnection();
    uc.setRequestProperty ("Authorization", "Basic " + encoding);
    BufferedReader br = new BufferedReader(new InputStreamReader(uc.getInputStream()));
     while ((inputLine = br.readLine()) != null)
     output+=inputLine;
    br.close();
catch (Exception e){}
ERROR:
cannot resolve symbol
symbol : variable host location: class com.sap.xi.tf._MM_CommunicationChannel_Stop
_ URL server = new URL("http", host, 8xxx, xyz);
^ 1 error
Any other way to get host and port?
Manisha

FTP and Port mapping

Hi
we get troubles with our FTP Server. The clients send a Syn with Src port 40000 then the Server replies with the the same dst port but i presume that the loadbalancer makes a port-mapping and translate the source Port to eg. 33000. Our firewall clearly drops the packet with the reason "Packet out of state". have you any idea ?
Here my config
service h01p6u_21
keepalive type tcp
keepalive port 21
ip address x.x.158.129
protocol tcp
redundant-index 11790
active
service h01p6v_21
ip address x.x.158.130
keepalive type tcp
keepalive port 21
protocol tcp
redundant-index 11800
active
content c01sg5_21
vip address x.x.x.140
add service h01p6v_21
add service h01p6u_21
port 21
protocol tcp
application ftp-control
active
!*************************** GROUP
group srg_c01sg5
vip address x.x.x.140
add service h01p6u_21
add service h01p6v_21
active

Hi Gilles
the problem that I have now is with ACTIVE FTP. I made PBR on the Loadbalancer. Passive FTP works either from the internet and from our internal network while Active FTP works only from the internet and doesn't work from our internal network. What we see is that the Loadbalancer sends the ftp-data packet out to the InternetVLAN (eg. VLAN 3605) and not to the VLAN 3603. I guess the problem is in my access-list. have you any Idea ??
My configuration
!*************************** GROUP ***************************
group srg_c01sg5
vip address x.x.152.140
add service h01p6v_21
add service h01p6u_21
active
!**************************** ACL ****************************
acl 1
clause 10 permit any x.x.172.0 255.255.255.0 destination any prefer FW_VLAN3605
clause 99 permit any any destination any
apply circuit-(VLAN3607)
acl 2
clause 10 permit any x.x.158.0 255.255.255.0 destination any prefer FW_VLAN3603
clause 99 permit any any destination any
apply circuit-(VLAN3610)
clause 15 permit any x.x.158.0 255.255.255.0 destination 10.0.0.0 255.0.0.0 prefer FW_VLAN3603
clause 20 permit any x.x.158.0 255.255.255.0 destination 138.191.0.0 255.255.0.0 prefer FW_VLAN3603
clause 25 permit any x.x.158.0 255.255.255.0 destination 192.168.251.0 255.255.255.0 prefer FW_VLAN3603
clause 30 permit any x.x.158.0 255.255.255.0 destination 192.168.250.0 255.255.255.0 prefer FW_VLAN3603
clause 35 permit any x.x.158.0 255.255.255.0 destination 192.168.0.0 255.255.0.0 prefer FW_VLAN3603
clause 40 permit any x.x.158.0 255.255.255.0 destination 172.16.0.0 255.240.0.0 prefer FW_VLAN3603
acl 10
clause 99 permit any any destination any
apply circuit-(VLAN3605)
apply circuit-(VLAN3603)
apply circuit-(VLAN2421)
apply circuit-(VLAN1)

Find host name and port number using query

Hi,
How do find the system_name, host_name and port no
using sql query or data dictionary.
plz

SELECT i.instance_name, i.host_name, f.release_name RELEASE, i.version, k.patch_level FROM
v$instance i, fnd_product_groups f, fnd_product_installations k WHERE
UPPER(SUBSTR(i.instance_name, 1, 4)) = UPPER(SUBSTR(f.applications_system_name, 1, 4)) AND
k.application_id = '200';

N8 default photo viewer and Nokia Maps

With the E52, I can view a photo (with geotag) with the default photo viewer. Select "Option/Show on Maps" and it will automatically opens up Nokia Maps showing where that photo was taken. And to navigate to that place.
With the N8 photo viewer, there isn't any such option. Is there any apps that could do that? Thanks

Seems it works the same way that on Nokia 5800xm as mentioned here ...

WRT160N V3 DMZ and Port-Forwarding dont work

Hi All,
i have a WRT160N V3 and DMZ or Portforwarding dont work.
i tried locally following
WAN_PC-> WAN-PORT -> WRT160N V3 -> LOCAL-PORT -> LOCAL_PC
The WAN_PC has a Static-IP 192.168.1.2, Subnet 255.255.255.0
The WAN-PORT has a Static-IP 192.168.1.1, Subnet 255.255.255.0
ON the WRT160N V3 i configured a DMZ on 192.168.0.100.and Disabled the Firewall.
On the LOCAL_PC (192.168.0.100:8888) is a Apache
So when i type 192.168.1.1:8888 on the WAN_PC i get NOOO Website from the Apache on 192.168.0.100:8888?
WHY??????????????
Solved!
Go to Solution.

Please correct me if I am wrong. My understanding of your setup is that you have a computer plugged-in to the internet port of the router and another computer plugged-in to the ethernet port of the router? Is that correct? You do not have a modem for internet connection or something like that? If you can post here a diagram that will be better. Thank you.

Default Host (DMZ) and Port Mapping together

Similar Messages

Maybe you are looking for