Delay by receive a call
i have iphone 4s and when i receive a call, have 2-3s delay, after this time can i talk...it is depresive, older ios 7.1.2 was without this problem. This bug have all ipohnes (4s, 5, 5s, 6, 6plus).... work Apple on fix?
recover ios installation in iTunes, recovery ios installation in iTunes with DFU clear....no effect. This is not a only my problem, many people have this problem, but no solution :-/
Similar Messages
-
4FXS-DID configuration problem using BRI to receive/send calls from/to PSTN
Hi to all.
Follow is the partial configuration of my CME.
It has a 4FXS card to use analog phones and faxes, and 4 ISDN Basic Rate interfaces.
On each port of the 4FXS DID card happens the following:
If I enable direct-inward-dial
I can receive calls from PSTN.
Off hooking the analog phone I cannot hear any free line tone. I cannot make any call from that phone.
If I disable direct-inward-dial
I cannot receive directly calls form PSTN.
Callers on PSTN after typing my number, they hear a free tone. Then just typing the extension desired the phone ring.
Off hooking the analog phone I hear a free line tone. I can make normal calls to everyone.
I have half the configuration working.
Where am I wrong?
I really appreciate your help.
Thanks to all.
Giorgio.
CME#sh ver
Cisco IOS Software, 2800 Software (C2800NM-IPVOICEK9-M), Version 12.4(24)T3, RELEASE SOFTWARE (fc2)
ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)
CME uptime is 2 days, 15 hours, 49 minutes
System returned to ROM by power-on
System restarted at 18:54:45 CDT Fri Aug 2 2013
System image file is "flash:/c2800nm-ipvoicek9-mz.124-24.T3.bin"
Cisco 2811 (revision 53.50) with 249856K/12288K bytes of memory.
Processor board ID FTX1120A08L
2 FastEthernet interfaces
4 ISDN Basic Rate interfaces
16 terminal lines
4 Voice FXS interfaces
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
1948656K bytes of USB Flash usbflash0 (Read/Write)
497448K bytes of ATA CompactFlash (Read/Write)
Configuration register is 0x2102
CME#sh telephony-service
CONFIG (Version=7.1)
=====================
Version 7.1
Cisco Unified Communications Manager Express
isdn switch-type basic-net3
voice translation-rule 1
rule 1 /^2929091\(..\)/ /\1/
rule 2 /^2929091\(.\)/ /\1/
rule 3 /^02929091\(..\)/ /\1/
rule 4 /^02929091\(.\)/ /\1/
voice translation-rule 2
rule 2 /\(.*\)/ /02929091\1/
voice translation-rule 10
rule 1 /\(^......$\)/ /0\1/ type national national plan isdn isdn
rule 8 /\(^......$\)/ /00\1/ type international international plan isdn isdn
voice translation-profile PSTN-IN
translate calling 10
translate called 1
voice translation-profile PSTN-OUT
translate calling 2
interface BRI0/0/0
description Isdn channels 1 & 2
no ip address
isdn switch-type basic-net3
isdn timer T310 60000
isdn overlap-receiving T302 3000
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI0/0/1
description Isdn channels 3 & 4
no ip address
isdn switch-type basic-net3
isdn timer T310 60000
isdn overlap-receiving T302 3000
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI0/1/0
description Isdn channels 5 & 6
no ip address
isdn switch-type basic-net3
isdn timer T310 60000
isdn overlap-receiving T302 3000
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI0/1/1
description not used
no ip address
shutdown
isdn switch-type basic-net3
isdn timer T310 60000
isdn overlap-receiving T302 3000
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
voice-port 0/0/0
translation-profile incoming PSTN-IN
translation-profile outgoing PSTN-OUT
compand-type a-law
description Connessione con CO Telecom channels 1 & 2
voice-port 0/0/1
translation-profile incoming PSTN-IN
translation-profile outgoing PSTN-OUT
compand-type a-law
description Connessione con CO Telecom channels 3 & 4
voice-port 0/1/0
translation-profile incoming PSTN-IN
translation-profile outgoing PSTN-OUT
compand-type a-law
description Connessione con CO Telecom channels 5 & 6
voice-port 0/1/1
description Disponibile
voice-port 0/2/0
input gain 14
connection plar 83
description Interphone 40
station-id name Citofono
station-id number 40
caller-id enable
voice-port 0/2/1
cptone IT
description Ced 35
station-id name CED
station-id number 35
caller-id enable
voice-port 0/2/2
cptone IT
description FAX_1 50
station-id name FAX_1
station-id number 50
caller-id enable
voice-port 0/2/3
cptone IT
description FAX_2 60
station-id name FAX_1
station-id number 60
caller-id enable
dial-peer voice 1001 pots
description **Sends call to PSTN line 1-2**
destination-pattern 0T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/0/0
dial-peer voice 2001 pots
description **Receives calls coming from PSTN line 1-2**
destination-pattern 2929091..
incoming called-number .T
direct-inward-dial
port 0/0/0
dial-peer voice 1003 pots
description **Sends call to PSTN line 3-4**
destination-pattern 0T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/0/1
dial-peer voice 2003 pots
description **Receives calls coming from PSTN line 3-4**
destination-pattern 2929091..
incoming called-number .T
direct-inward-dial
port 0/0/1
dial-peer voice 1005 pots
description **Sends call to PSTN line 5-6**
destination-pattern 0T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/1/0
dial-peer voice 2005 pots
description **Receives calls coming from PSTN line 5-6**
destination-pattern 2929091..
incoming called-number .T
direct-inward-dial
port 0/1/0
dial-peer voice 2035 pots
description **Receives calls coming from PSTN to Extension 35**
answer-address 35
destination-pattern 35$
incoming called-number 35
port 0/2/1
dial-peer voice 2040 pots
description **Receives calls coming from PSTN to Extension 40**
destination-pattern 40
incoming called-number 40
no digit-strip
direct-inward-dial
port 0/2/0
dial-peer voice 2050 pots
description **Receives calls coming from PSTN to Fax 50**
destination-pattern 50
incoming called-number 50
no digit-strip
direct-inward-dial
port 0/2/2
dial-peer voice 2060 pots
description **Receives calls coming from PSTN to Fax 60**
destination-pattern 60
incoming called-number 60
no digit-strip
direct-inward-dial
port 0/2/3
CME#Hi Paolo.
Sorry for the delay. I was on holiday.
I would like to keep separate incoming calls from outgoing calls.
So I decided to keep two dial peers for every BRI interface.
I followed your suggestion on eliminate commands:
"incoming called-number" on FXSs,
various "progress_ind" on BRIs
Also I eliminated "direct-inward-dial" on FXSs,
Today I reconfigured and right tested the dial peers as following:
! Bri Interfaces
dial-peer voice 1001 pots
description **Sends call to PSTN line 1-2**
destination-pattern 0T
port 0/0/0
dial-peer voice 2001 pots
description **Receives calls coming from PSTN line 1-2**
destination-pattern 2929091..
incoming called-number .T
direct-inward-dial
port 0/0/0
dial-peer voice 1003 pots
description **Sends call to PSTN line 3-4**
destination-pattern 0T
port 0/0/1
dial-peer voice 2003 pots
description **Receives calls coming from PSTN line 3-4**
destination-pattern 2929091..
incoming called-number .T
direct-inward-dial
port 0/0/1
dial-peer voice 1005 pots
description **Sends call to PSTN line 5-6**
destination-pattern 0T
port 0/1/0
dial-peer voice 2005 pots
description **Receives calls coming from PSTN line 5-6**
destination-pattern 2929091..
incoming called-number .T
direct-inward-dial
port 0/1/0
! FXS interfaces
dial-peer voice 2035 pots
description **Receives calls coming from PSTN to Extension 35**
destination-pattern 35
no digit-strip
port 0/2/1
dial-peer voice 2040 pots
description **Receives calls coming from PSTN to Extension 40**
destination-pattern 40
no digit-strip
port 0/2/0
dial-peer voice 2050 pots
description **Receives calls coming from PSTN to Fax 50**
destination-pattern 50
no digit-strip
port 0/2/2
dial-peer voice 2060 pots
description **Receives calls coming from PSTN to Fax 60**
destination-pattern 60
no digit-strip
port 0/2/3
Thanks a lot Paolo. :-)
Giorgio. -
I am facing issue in Receiving incoming calls, Name not getting displayed though the same has been saved in my phone book!! I have done sync from Windows contacts.. please help if some1 knows how to rectify the issue...
Has your carrier been having issues with Call Display? Do the telephone numbers come up when people call, or does it just show 'Unknown Number' or 'Blocked' ?
-
IPhone 5s is not receiving incoming calls
Hi everyone,
I am having problems with receiving incoming calls after I got the 5s. Sometimes, it didn't even ring, just went straight to voice mail even though the signal was strong. Sometimes they have to call me up to 8 - 10 times for the phone to ring once and the other calls will appear as missed calls. Does anyone experience the same problem with the 5s? Should I bring it to the apple store for them to take a look?
ThanksDouble check settings - do not disturb - off
-
Iphone 5s cannot call out any calls, but still can receive incoming calls and sms
Hi
anyone experiencing this problem? After buying iphone 5s less than 2 months which I never did in the past, I could no longer make any phone calls out, yet i still can receive incoming calls and data.
Could someone kindly assist in this?Contact your carrier. Phone functions are a carrier responsibility. Have them check your account. Are you seeing any error messages?
-
Why does my iPhone 5s not receive incoming calls
My iPhone 5s does not ring when receiving incoming calls yet I have signal, do not disturb is off and I receive texts or voicemails notifying me of a missed call which I can return immediately. What is going on? How can I fix this?
Yes the ringtone works. I know you are trying to help however I am fairly tech savvy and have eliminated all basic user defined settings that could cause the issue. The issue is not that there is no sound the issue is that there is no call incoming notification at all. The call does not connect to my Boone to even make it ring and display as a missed call
-
Iphone doesnt receive incoming calls
Hi, for about 2 weeks i cannot receive incoming phone calls any more. Earlier it worked without problems. Now even in the phone log, no incoming calls are registered. I can make phone calls by myself, i can receive incoming calls by facetime, but no phone calls or sms. The phone is not muted (i tried the button already) . A complete reset of the phone did not change anything. Has anybody an idea what i can do?
My carrier did not know a solution, but proposed to send the iphone back to apple.
I removed all photos and videos. Just before i wanted to send it back, it suddenly worked again.
Now i wonder how long it will work. After all it seems like a software problem to me. -
My iphone 4S has problem in making and receiving the calls. While making the call , call fails and netwrok disappears. Like wise no voice is heard for incoming calls. This happened after return from the overseas travel.
Hello SamSax
Check out the assist page below for troubleshooting call connectivity.
Calls and connection issues
http://www.apple.com/support/iphone/assistant/calls/
Thanks for using Apple Support Communities.
Regards,
-Norm G. -
IPhone 4 Can't receive incoming calls and sms after 3G has been activated
I can't receive incoming calls and sms on my iPhone 4 after the 3G connection has been activated and used actively by me. Outgoing calls and messages do work and as long as I use the Wi-Fi connection everything's fine but the problem appears after switching to 3G. Any help? Thx in advance!
I think the next step is to do a reset by holding the sleep and home buttons down at the same time until the Apple logo appears. If you haven't done this before, keep holding the buttons when the turn off slider appears. The screen will go black and after what seems like an eternity, actually several seconds, the Apple logo will appear. When the logo appears, release the buttons.
-
i got problem when trying to call my iphone 4 using facetime with my Macbook Pro 13',it did ringing,but my iphone 4 did not receive that call as if nothing happen.But,when the call ended,that call appeared in the missed call list.fyi both are connected to internet.Help!! thank you in advance
i got problem when trying to call my iphone 4 using facetime with my Macbook Pro 13',it did ringing,but my iphone 4 did not receive that call as if nothing happen.But,when the call ended,that call appeared in the missed call list.fyi both are connected to internet.Help!! thank you in advance
-
I cannot receive phone calls or messages when iPhone screen is locked
Hello,
i have an iPhone 5.
i Am unable to receive phone calls or text messages when my screen is locked. When I unlock the screen the missed call doesn't even appear so I have no idea anyone has called me. Text messages come through at about 12:30am every night.
i Have tried EVERYTHING I could find in forums and Apple trouble shooting. This is my last resort other than sending it to Apple.
iit is as if "do not disturb" is stuck on, but it isn't.
i Have tried:
changing all all do not disturb settings.
checked call forwarding etc.
checked mute
my silent button is not on.
i have reset every setting and then even reset the phone and manually transferred everything back onto it rather than restore It from previous back ups.
oout it in recovery mode.
i Have no success with any.
the weird part is when I first lock the screen and try to call it, it does ring. But if I give it a minute or more it won't ring.
does anyone have any ideas or anything that may help?
PLease, please, pleaseI Have also checked blocked numbers and swapped SIM cards from a completely different carrier so it's not the carrier either
-
MacBookPro Cannot Make/Receive Phone Calls
Hello,
My MacBookPro (early 2013 Retina) cannot make or receive phone calls. I'm on the same wifi network, my bluetooth is on, I can send/receive texts and SMS, I have the most recent software upgrades, but I can't make calls. As of right now when I try it says "Your iPhone and Mac must be on the same Wi-Fi network".
The same thing is happening with my iPad.
In FaceTime under "iPhone Cellular Calls" I've tried to move the slider over to the right to allow calls on MacBookPro and iPad, but it says "Cannot Turn on iPhone Cellular Calls- FaceTime and iCloud must be signed in to same Apple ID to use iPhone Cellular Calls". THEY ALL ARE ON THE SAME APPLE ID!!!
IT MAKES NO SENSE!!!
I am actually having issues with handoff JUST on my MacBookPro if that is any sort of useful information. It works just fine on iPhone and iPad.
BBHello Bluebuck,
The article linked below details a number of troubleshooting steps that can help get Continuity working correctly.
Get help using Continuity with iOS 8 and OS X Yosemite
http://support.apple.com/en-us/TS5458
Cheers,
Allen -
I have forgotten my security questions and cannot purchase apps. My rescue email was entered with an error .me instead of .mw so I can't reset my account. Is there a way to contact support via email ? as I can't receive a call.
Thankshttp://www.apple.com/support/contact/
would be the place to start -
My husband and I shared the same apple id I accidentally deleted his number from the iCloud And now his phone won't receive phone calls or text what do I do
In preferences turn on iTunes sharing in iTunes preferences and keep iTunes turned on in both accounts. Or better yet put the iTunes library on the main HD rather than in an account and set the location of the library to that location in iTunes preferences.
-
Every time I make a call or I'm receiving a call my phone is extremely static i can't hear the person on the other line and the person on the other line cannot hear anything They say that they hear a lot of static now my videos when I play a video on YouTube for instance works just fine Siri works just fine. I can't make a call or receive a call whatsoever because all I hear is static and I haven't dropped the phone in water nothing has really happened this literally happened overnight
This is a wireless carrier issue. The fact that the speaker & microphone work properly for other apps is a great indicator that your device is fine.
Contact your wireless carrier about your call quality issue.
Maybe you are looking for
-
Creation of Text File on Client Machine
I am using Oracle 11i EBS and I have a requirement to create a text file on the client's machine. The name of the file is suppose to be on a particular format (DDMMYY.TXT). It is an urgent requirement from our client and we need to go live in 3 days.
-
How do to set up time limits on a guest network
I have a new generation Airport Time Capsule and I have set up a Guest Network for my kids but I would like to set up time limits on the Guest Network also, is there a way to do it?
-
Why is latency for sync messages more than async messages in PI?
Hi All, Is it normal thing for Sync messages to have more latency time than async messages in PI. if yes then what is the reason behind it? Also whats the appropriate latency time in PI? Thanks
-
Custom Phone theme Xperia arc S?
Is there a way to change the theme of Xperia Arc S running on ICS without using a custom launcher? Solved! Go to Solution.
-
Pavilion dv4 Cd drive not working
Hi guys about two months ago my cd drive decided to stop read my my cds as well as to stop burning disc. Ive tried updating it and cleaning the eye and i know that its not the cds because they work on my desktop. the funny thing is that the drive do