Delay when using remote?

Hello,
When I first turn on my 46in lcd tv using the cable remote, I must wait a full 60 seconds before ANY function on the remote works. Any Assiatance would be greatly appreciated. Thank You/Joe
Solved!
Go to Solution.

Try resetting the TV to factory defaults. Press "MENU" and open the "Setup" menu. Select "Installation" and then "System Information." Select "Factory Defaults" and then confirm.
If the problem persists, please contact support at (800) 631-3811.
- Peter

Similar Messages

Printing to a Printer Connected to TIme Machine when using Remote Desktop

Hi,
I am having trouble printing to a printer connected to our wireless network via Time Capsule when I am on my remote desktop connection. Printing from all other programs work. I downloaded Bonjour on our Windows based server, and it did not detect any printers. When I am connected directly to the printer, I can print when using remote desktop. Any suggestions are much appreciated.
Thanks!
Mac OS X (10.5.4)

Airport Extreme/Express do emulate Jetdirect/port 9100 printing, but that isn't what they use for printing from OS X. OS X and the Bonjour/airport software use USB port redirection, a unique and separate method.
If the HP driver supports any protocol over ethernet, it would be appletalk. Does that router server use appletalk?

Midi Delay when Using Rewire?

I am experiencing really bad midi delay when using
LE7.1 & Reason 3.0 in Rewire mode.
Should this be happenening? I take it that I am setup properly for rewire or I would not hear anything at all. I can trigger Reason synths via LE in rewire mode but the delay is so bad that it is unplayable.I thought "latency" issues only occured when using audio. I have tried different buffer sizes to no avail.
Any ideas?

ok I'll answer my own post.
Issue was a toggle box in LE prefs to control "Rewire Behaviour". Set it to "Live mode" not "Playback" mode solves this issue.

RMBP reaches 104C when using remote desktop. Is this normal?

I have a new rMBP that is reaching temps of 104C when using remote desktop or other moderately intensive applications. Is this normal?

No, that's way too hot. It's only a few degrees below automatic thermal shutdown.

Apple TV3 turns off and on when using remote, already reset and restarted.

Apple TV just started acting up yesterday. When using remote, light on Apple TV would turn off and on so it would somewhat work when the light was on and would not when light when off. When light is off and in a menu selection, cursor would just move to the end of the list and stop. Already restored back to factory and reset it. Difficult to program after reset when remote only works part of the time when the light goes on so stuck in out of the box condition. Any help on this? Thanks!

Hello stiktani,
After reviewing your post, I have located an article that can help in this situation. It contains a number of troubleshooting steps and helpful advice concerning Apple TV remote issues:
Apple TV (2nd and 3rd generation): Resolve issues with Apple Remote
Thank you for contributing to Apple Support Communities.
Cheers,
BobbyD

Report hangs when using Remote Desktop

I am having trouble with Crystal Reports 11. I was wondering if there is a known issue when using it in conjuction with Remote Desktop.
Here is the scenario.
I am using Remote Desktop to connect to a server.
I am running a report using Crystal Reports 11.
The records have already been retrieved (approx. 800,000 records) and is printing - slowly.
It takes around 75 minutes for the report to print 12 pages.
If the Remote Desktop connection is closed, then re-established, the Crystal Reports pops up a message box stating "Not Supported". The pages of data the were previously printed are now blank. (For example: if it was on page 1 of 9+ it will go back to 1 of 1+ and the page will be blank.)
If I use a VPN to connect to the network, then use the Remote Desktop Connection to connect to the server, the connection will periodically disconnect and the re-establish. This does not occur when not using Crystal Reports.
Is there a problem with using Crystal Reports with Remote Desktop? Is there a better way to run my reports remotely?
Thanks for any input.
Ryan

You may be better off posting this in the Crystal Reports Design forum as that team supports issues regarding working with the CR designer:
SAP Crystal Reports
Ludek

Delay when using doubletap and hold with bootcamp 5

Hi,
I just bought a 15" MBPro and discoverd a delay when I use doubletap and hold to scroll or to mark text or drag. Is this a know problem of the bootcamp trackpad driver?
Hoping for answers
Bye
Michael

I have the same problem, except that I'm using the Apple Trackpad in Windows 8 in Boot Camp on a 2012 iMac, so my guess is that the driver is to blame.

Delay when using BC partition in VMware Fusion

Hi everyone,
I've been wondering about this for months now and finally decided to ask for your experiences.
When using my Windows (XP Pro 32bit) Boot Camp partition as a VM in Fusion I always get a delay when the desktop appears and the taskbar items are loading. I can see that the VM Tools seem to be loading (taskbar icon) while this is happening. This usually takes at least 10-15 seconds on my MBP (C2D with 4 GB RAM) and it has been the same for the last few versions of OS X and Fusion.
Is this delay normal when using the BC partition? It definitely isn't there when booting a regular VM. If so, how long does it take for you?
Thanks!
Björn

Nope, KBDMGR.EXE is located in "Program Files" and autostarted via the RUN registry-entry. It's seemingly not even a real driver, but merely a bridging process that administers the drivers.
If you run bootcamped Windows without KBDMGR you cannot use the special function keys (brightness, loudness etc) and at least in Vista you have to do some manual settings every time you start Windows in order make tap-to-click usable without KBDMGR (a better and easier way is to start KBDMGR once and then stop it again if you don't want/need it).
Manually enabling tap-to-click and chosing the Boot-OS is possible without KBDMGR being loaded even once, you can just call the settings application from Windows/System32. The Readme coming with my Script explains how to find that and possibly use a keyboard- or icon-shortcut for that.
Theoretically it can be stopped/killed via Process-Manager and started manually by just calling the exe file. Practically that only works as long as the RUN entry in the registry remains intact and points to an existing file.
Along other things my script explains how to replace KBDMGR.EXE with a dummy file which in turn allows to start Windows without it and later loading it manually if needed (preferably via a keyboard- or icon-shortcut as described in the Readme of my script).
Personally I use Right-ALT+, for opening the Settings and Right-ALT+. for switching KBDMGR on/off (along with switching the F-Keys from Standard to Special functions alongways). Works like a charm.
Message was edited by: T1mur
Message was edited by: T1mur

Significant delay when using the "tap to click" trackpad function

(I accidently post this in the wrong forum -- for the old MBP -- so this is a repost)
Hello everyone! I bought a 2.4 Ghz unibody MBP like 3 weeks ago. I had an issue and they replaced the computer with a new one at the store. Today is the first day of using the new laptop. They switched out the ram upgrade and the hard drive.
The issue seems to be that when using the tap to click function on the trackpad, there is a relatively significant delay (at least for a click). With the regular mouse button the delay isn't there. Such as if I'm clicking on the finder or the file tab, there's a bit of a delay before they pop up, compared to instantaniously with the mouse button. When using the trackpad for regular types of tasks, there is a bit of a delay sometimes too. Such as I'll be moving the mouse across the screen and it will stop.
Please help me out. If I could solve it without going back to the Apple store that would be great. Thanks everyone in advance.

Update: I think the 1/2 second delay is too long of an estimate, but the delay is significant enough to make me notice something has to be wrong. My previous MBP had no delay.
When moving the mouse around, I'm not sure if it's a MBP issue, but occasionally the mouse seems to "get stuck" on the screen and I have to begin moving my finger again on the trackpad. This happened on the first MBP too.

Kinect for windows sensor does not start when using remote WMI

Scenario:
I have written a software (lets call it kinectRecorder.exe) that uses "kinect for windows sensor" to record images. The machine that connects to the kinect sensor has windows 8.1 and kinect v2 installed. The software is able to successfully records
images from kinect sensor when running locally. (meaning if I hit f5 from vs2013, frames are recorded to local disk)
Due to resource constraint and other requirement, I have to remotely kickoff kinectRecorder.exe on the windows 8.1 machine from a windows 7 machine. on the windows 7 machine, I remotely kick off the kinectRecorder.exe using windows WMI infrastructure.
The credential used for windows 8.1 machine and windows 7 machine are the same under same windows domain. the credential used to authenticate in wmi is also the same, I can see the user name running kinectRecorder.exe after kinectrecorder.exe is started
remotely.
Problem:
The result is that kinectRecorder.exe starts ok, but after the kinectsensor.open call, isavailable property changed to false, meaning sensor not detected.
Question:
What's stopping kinect sensor to be detected/opened (i'm not sure what the correct jargon is here)?
I have been search the web, In msdn documentation (known issues), I cannot find the problem being mentioned. I wonder if I'm the only person who has encountered this issue before.
Any pointer is hugely appreciated.

Kinect is not supported within the context of a service because of the underlying need for a user session, see
https://social.msdn.microsoft.com/Forums/en-US/72cecf8b-ac64-47e2-b54b-ddbd1dc237c9/calling-kinect-sdk-apis-from-a-windows-service-is-not-possiblesupported?forum=kinectv2sdk
Can determine that the system has at least one logged in user and can you launch the application within that users session? KinectMontior/KinectService must be running for the runtime to get any data from the sensor. If you use Remote
Desktop to log into that user session, you can confirm this works by running any of the samples and they should work without issue(remember to ensure that your audio remoting is left on the server, see troubleshooting guide
https://social.msdn.microsoft.com/Forums/en-US/20dbadae-dcee-406a-b66f-a182d76cea3b/troubleshooting-and-common-issues-guide?forum=kinectv2sdk).
Carmine Sirignano - MSFT

Delay when using Airport Express

a friend hooked up an airport express yesterday in a place with a few macs - there seems to be about a 2 second delay when clicking on any mp3 song in itunes. Is this normal?
Any way to reduce the delay?

Thanks snives,
You're talking about Airtunes right
Yes, Airtunes.
Try to not let it bother you.
Just can't use it for professional timing needs - so useless for us...
Alternative wireless methods would be to transmit raw audio using another device
* interesting - what other device are you thinkng of?
or use an audio cable if that's possible in your situation.
already tried that - works fine - but don't want the cable

Logic, delay when using midikeyboard

What is wrong when my midi keyboard conected to my Macbook pro and logic gives me a delay when i play on it, dont know for how long, but just a little irritating delay, for every note. Makes it impossible to play

Read this:
http://help.apple.com/logicpro/mac/9.1.6/en/logicpro/usermanual/#chapter=2%26sec tion=0
Look at the section called configuring your audio hardware.......... or wait around until someone tells you what to do.

ITunes won't play when using Remote Desktop

I noticed that if I access my home computer from work remotely using Windows Remote Desktop, and that iTunes is opened on my Home PC, when I get home, I can't play music from iTunes.
I need to close iTunes and re-open it again...
any idea?

Sorted it.

IPod Touch 4G not detected in iTunes 10.0.1.22 when using Remote App 2.0

I'm guessing Apple's Remote App 2.0 works well for iPhone 4 and iPad, but when I try using it with iPod Touch 4G, it does not show up in devices to enter the passcode.
same wifi network
iTunes 10.0.1.22, Home Sharing On, Library Sharing enabled, Looking for remotes enabled.
iPod Touch 4G (iOS 4.1) (no problems with wifi)
Apple's Remote App 2.0 Home Sharing login works well. Adding Library produces 4 digit passcode.
BUT, again, it does not show up in Devices to have the opportunity to enter the passcode.
iTunes is an approved app in firewall settings.
Win 7 (32bit) Network Detection/Printer&File Sharing is enabled.
Interesting:
When I try to connect to Airport Express with my PC,
I receive "unknown error (-15006)"
Another iMac running iTunes 9 is able to stream music to the airport express without problem.
Using my PC, I'm able to connect to the iMac, and stream music from the iMac to my PC.
When Airport Utility (on PC) is open I can't detect Airport Express (even though the light is solid green.
I'm still guessing iTunes 10.0.1.22 has AirPlay/AirTunes issues, and in general doesn't want to detect any wifi devices.
I haven't yet looked up the error code, but would love to hear some thoughts out there.
Anyone else have similar issues? Are there any fixes?
Please share.
Thanks.

another piece of info about Remote App 2.0 on my iPod Touch 4G
I'm able to turn on the Home Sharing button inside the app.
The text description below it says:
"Remote will automatically find the iTunes libraries and Apple TV's that have Home Sharing turned on using the account _____."
Both my iTunes and this app have Home Sharing turned on and logged-in using the same account info, but Remote App is NOT automatically detecting my iTunes library. Nothing happens!! When I then click the "Add an iTunes Library" button, Remote app generates a 4-digit passcode number, but still won't detect my iTunes account. The same is true for iTunes; it will not detect my iPod Touch as a nearby wireless device on the same wifi network.
I don't know how to move beyond this issue!
Am I correct to assume that signing into my Home Sharing account on Remote App should automatically find my iTunes Library and populate the Remote App screen on my iPod Touch with a button/link to start navigating my iTunes Library, while at the same time iTunes should detect my iPod Touch in Devices and give me a screen to enter the passcode? Do I actually need a passcode if I'm using Home Sharing?
I'm guessing that Home Sharing is for when I'm at my house, and a passcode is for when I'm at a friend's house. Could someone confirm if this is really the case?

Synaptics touchpad blocked & delay when using the keyboard in Windows 8.1

Sometimes (possibly when I use the keyboard and then quickly attempt to move the mouse arrow on the screen with the Synaptics touchpad), I am unable to move the cursor for a half of second-or-so.
Sometimes I cannot tap to click, maybe, few seconds (it is very annoying).
There are some Mouse and touchpad settings in Windows 8.1 ("To prevent the cursor from accidentally moving while you type, change the delay before clicks work") which I set to "No Delay (always on)" but it does not work, either.
I also checked the following registry key:
HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\PrecisionTouchPad
but "AAPThreshold" is set correctly to 0 (No delay).
But I still experiences problems and touchpad does not work while typing and sometimes also few moments after.
Using HP Zbook 14, Win 8.1 x64, Synaptics driver 17.0.18.23.

Hi,
If you trying connect two Universal apps through Bluetooth, can you check if the
Windows 8.1 Bluetooth RFComm sample runs fine on both the devices? I successfully tested the Windows 8.1 Bluetooth RFComm sample on Laptop (Windows 8.1) and Windows Phone 8.1 (paired).
Make sure the service which you are trying to advertise/listen is supported by both the devices.
-Sagar

Delay when using remote?

Similar Messages

Maybe you are looking for