Delays in net access restriction

XI31 - IIS6.0 - .NET (no tomcat)
It is taking users "minutes" to bring up the net access restrictions... How can I speed this up PLEASE?!?!!?

Well I must admit this does not really sound like a best practice. But since this is a rather unusual setup I would recommend to open a case by SAP support (http://service.sap.com/support) and ask if this delay to display the list with the 1800 restriction is by design or a bug.
Regards,
Stratos

Similar Messages

Access Restrictions again...

Ok so I cant get the access restrictions to work. I input the mac addy of the pc i want to restrict and no matter what times I put in the pc can still acess the net. In other words, I can restrict it to 24/7 no access and it still wont work.
Anyone able to get this to work? Im using WRT54GL v4.30.5

I think i figured it out. You have to have the firewall enabled for it to work (duh) so far it seems to be working now.

E1000 Access Restrictions Issue

I attempted to create a rule to limit access only to specific URLs during a specific time of day. However, it seems to have blocked all of the internet for the user at that MAC address, outside of the times I had chosen. I double-checked to make sure that the radio button next to 'Allow' was selected in the section that reads: "Internet access during selected days and hours." I don't know what I'm doing wrong. How is the time of day determined by the router? Is there a clock which needs to be set to my time zone somewhere? If so, I've yet to find it. Also, why is it blocking all access to the internet? It should only be blocking 3 URLs.

The Access Restrictions feature of a Linksys router allows you to limit Internet access on your network. You can deny certain computers’ Internet access or block certain applications and services. This article will provide instructions on how to set up Access Restrictions by blocking certain days or hours.
Here is the link for the same: http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=20b29e54474a4a17aff594cb659747ea_4041.xml&pid=80&r...
The time zone on your router should be set correctly according to the time zone in your current location. This is to ensure that the Parental controls feature will block Internet access on the exact time you specified. To configure the time zone on your router, access your router’s web-based setup page, then go to Basic Setup sub tab under the Setup tab. Click the Time Zone drop-down menu and select the appropriate time zone. Once done, click Save Settings.

WRT120N v1.0.07 Access Restriction Problem

My Wireless-N Home Router WRT120N with version 1.0.07 seems to have a problem blocking Sites through scheduling with Access Restriction "Allow" ...
I notice that... when I enable access restriction, with policy and some range of computers connecting to my router , and set it to "allow" from "monday - friday" from "8am-6pm" .. with a purpose of blocking some social networking sites, example facebook, It works perfectly fine. But when the "scheduled" time comes ( before 8am and after 6pm ).. I cannot access the internet.. router is working, it detects my modem.. but no internet connection.
It always happen before and after the "scheduled time" before the configured access restriction takes over. I have to disable the Access Restriction to continue our internet access.

In this case, I would like to ask whether you have upgraded the firmware of the router yourself? If yes, did you reset and reconfigure the router after the firmware upgrade? If you haven't, then I would recommend you to reset and reconfigure the router. The following link shows how to reset the router http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=eaa3127db5f4402584c959a7251e754c_4008.xml&pid=80&r...
Click on the link below which shows how to reconfigure the router in case of a cable and DSL connection:
Cable connection - http://www6.nohold.net/Cisco2/ukp.aspx?pid=80&vw=1&articleid=3686
DSL connection- http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=20ee1457387f40178cd5f41d4b585db4_3687.xml&pid=80&r...

ABOUT wrt54g 'Access Restriction'

Dear all:
once the duration of rule expired. It won't apply another rule by the time serial.
For example, I set up one of PCs was allowed to access internet between 7:00am~11:55am. This PC could access to internet after 11:55am, even I set another rule for this PC with duration 12:00pm~18:00pm.
Is any solution for my needs.
Beswt Regards
tom
Solved!
Go to Solution.

The Access Restrictions feature allows you to limit Internet access on your network. You can deny access to certain computers, block certain applications and services, and block certain websites by the use of keywords or by the URL at a given time. This feature allows you to customize up to 10 different Internet Access Policies for particular computers, which are identified by their IP or MAC addresses.
Here is the link Implementing Access Restrictions for computers: http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=20b29e54474a4a17aff594cb659747ea_4041.xml&pid=80&r...

WRT54G Access Restriction Time /Day Problems. Need Help!

Hi,
I have a WRT54G wireless router. When I set the access restriction time to DENY everyday from 11:00pm to 6:00am, it displayed that "The end time must be bigger than start time!". It is from 11 at night to 6 in the morning. How else do I set it? I even upgrade the firmware to v4.21.1 but it still does not work with that time setting. I tried to set to ALLOW everyday from 6:00am to 11:30pm and it accepted the settting but it just applied the restriction right away without waiting for the right time (after I enable it, none of the laptops can access internet even its only 9:10pm).. The time in the linksys setup page is correct as well as all my pcs. Please help! Thanks.

The Access Restrictions feature of a Linksys router allows you to limit Internet access on your network. You can deny certain computers’ Internet access or block certain applications and services.
Here is the link for setting up the Access Restrictions on a Linksys router: http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=20b29e54474a4a17aff594cb659747ea_4041.xml&pid=80&r...

EA2700/3500/4500 Access Restrictions

I can't find info about Access Restrictions in new series of routers. (http://www6.nohold.net/Cisco2/ukp.aspx?pid=80&vw=1&articleid=24957)
Do new routers have both Parental Controls + Internet Access Policy? I need this http://www6.nohold.net/Cisco2/ukp.aspx?pid=80&vw=1&articleid=4041

paultarasov wrote:
I can't find info about Access Restrictions in new series of routers. (http://www6.nohold.net/Cisco2/ukp.aspx?pid=80&vw=1&articleid=24957)
Do new routers have both Parental Controls + Internet Access Policy? I need this http://www6.nohold.net/Cisco2/ukp.aspx?pid=80&vw=1&articleid=4041
Yup, I agree with Wendel48.

Delay in Share access locally on windows 2008 r2

HI All,
Have been facing with an issue in which shares hosted on one of my server sometimes take a long time to open in explorer even if tried by IP/hostname/Fqdn..sometimes the lag is for more than 40sec ..It happens rarely once or twice in a month but causes issues
with our processes..During the issue the delay in share access occurs from diff servers including locally on the server..tried from win xp/win7/windows 2003/windows 2012.
Some options were opted like disabling RSS,checksum,TCP/Ip offload ,firewall disabled,SMB patch
but in vain.
Has anyone encountered such issues.Please let me know if anyone has any fix for the issue.
Infra:
OS:windwos 2012 r2 SP1 ent
App: sql 2008 r2
ManeeshB

Hi,
Since the issue also occurred locally, you could try the steps below to troubleshoot the issue:
1. Check the hard drive containing the folder that is causing the slow downs.
2. Check the folder optimization preference to see if the automatic optimization got it right.
3. Disable indexing temporarily to see if it resolves the slow folder issues.
For more detailed information, please refer to the article below. The article applys to Windows 7, but you can also try the troublshoot steps on Windows Server 2008 R2.
How To Fix Slow Folders In Windows Explorer
http://www.ghacks.net/2011/06/09/how-to-fix-slow-folders-in-windows-explorer/
Please Note: Since the website is not hosted by Microsoft, the link may change without notice. Microsoft does not guarantee the accuracy of this information.
Best Regards,
Mandy
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

WRT54G2 and WRT54G locks-up (freezes) when blocking web sites using Access Restrictions

I am convinced that a few Linksys routers such as WRT54G2 and WRT54G have a major issue when blocking web sites using Access Restrictions (Internet Access Policy). After a few hours of internet access by 15 wired users the Linksys locks-up and blocks all internet web access. The only solution is to restart the power on the router.
We are currently using a Linksys WRT54G2 v1 (firmware 1.0.04). We upgraded the WRT54G2 v1 firmware to the latest 1.0.04 version which did not resolve the issue. NOTE: We were previosuly using a a Linksys WRT54G v1.1 (firmware 4.21.1) until the power supply blew a week after we started blocking web sites using Access Restrictions (Internet Access Policy).
Basically, we have a T1 internet connection and a hub connected to the Linksys router. We are trying to block several web sites such as facebook, myspace, etc. for 15 wired users. We do not use wireless connections.
This is the 2nd time it happened with 2 different models.
Please help ASAP.
Thank you,
Lance
(Mod note: Edited post. Some parts off topic.. Thanks!)

Also, you have already upgrade/re-flash the firmware of your Linksys Router you need to reset and reconfigure your router from scratch. Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...

How to configure CLI/DNIS based access restriction in 5.3 ?

Hi,
does anybody have an idea how the setting
define CLI/DNIS-based access restrictions which is defined in ACS v. 4.2
can be configured in acs 5.3 ?
in v. 4 for every user in a group with 40 members a different CLI is defined for each. How can I configure that in version 5.3 ?
any help as always much appreciated!

The equivalebt to NAR functionality can be found at:
Policy Elements > Session Conditions > Network Conditions > End Station Filters
Can then define an object with a set of CLI values
These objects can then be used in policy conditions. So can create a condition with a set of CLI values and then match in authorization policy for values that are included in this set and set authorizations accoridngly
Not sure if this is your use case but hopefully may be a start

Access restrictions timing off by 1 hour

I don't know if anyone else is experiencing this problem. I have set access restrictions on my WRT610N router and they execute an hour earlier than set.
I checked the time zone settings, the system clock and all seem correct. I have a rule that is supposed to turn off access to the Internet at 11:55pm. However, the rule gets executed at 10:55pm.
This was happening on my first WRT610N which was also dropping network connections. So, I returned that unit and got a replacement.
The new unit does not drop connections but has the same timing problem. The only solution I have found is to change the time zone to the next one that is 1 hour behind my time zone.
Please let me know if anyone else has experienced this same situation.

My ISP is on the same town as I am. The information they are supplying appears to be correct as my WRT54G uses the same information and its rules execute properly.
I think there is a problem with the WRT610N. My solution is temporary I hope that Linksys will fix this problem.

WRTU54G-TM Slow Setup Page and HTML Error on Access Restrictions Page

I have a WRTU54G-TM Wireless Router. It has v1.00.21 firmware and I have done a reset with no solution. Everything seems to work, except the setup pages load very, very, very slow. Also in Internet explorer I get an HTML error on the access restrictions page. Resets don't help. The router did not have this issue until about a month ago that I recall. I can see on the access restrictions page the gray shading is all lined up except at the bottom on the page, like ther is some sort of issue in the html within the router.
One more problem, after I reset the router the saved config file I made would not change the default settings back, I had an older saved config file also, it would not work either.
Is this an issue with this firmware version? Any one else see this?
Message Edited by johnsonle9 on 01-24-2010 01:24 PM
Message Edited by johnsonle9 on 01-24-2010 01:24 PM

Are you getting the same problem with another computer...?
Try using different computer and check if you are getting the same problem or not...If yes then,I would suggest you to re-flash/upgrade the router's firmware,reset the router and re-configure it from scratch..Do not use the save config file.

Access Restrictions bug of firmware 1.01.1 for WRT54G V5 V6

I am using WRT54G V5.
The Access Restrictions function won't work properly when using firmwares 1.01.1 and 1.01.0. Ports can't be blocked by using the "Blocked Services" in this function.
Now I have to switch back to 1.00.9 to make the port blocking work, but there is a DHCP server issue which could only be fixed in 1.01.0 or above.... Could someone fix this BIG BUG and roll out a new firmware????
Thanks a bunch.
Message Edited by Dennis_Hsu on 01-08-200705:02 PM

What is your Fragmentation and RTS threshold value? I'm not sure if I'm reading your message right, but it says as far as I can understand 30. The value should be 2304 instead for both.
Ty changing the wireless channel also to either 1, 6 or 11.

Access restriction error? not sure how to fix it....

I am trying to use JPEGImageEncoder and i imported import com.sun.image.codec.jpeg.*; fine but i get the following error on my code:
CODE:
JPEGImageEncoder encoder =JPEGCodec.createJPEGEncoder(outImage);
ERROR:
Access restriction: The type JPEGImageEncoder is not accessible due to restriction on required library /usr/local/java/jdk1.6.0_07/jre/lib/rt.jar
I am not sure how to fix this... anyone know what needs to be done? I am using eclipse and i see the rt.jar in my library....
thanks!

MikeTheBorg wrote:
OK, I agree it's simpler for simple cases, but how do I do something like this:
          JPEGImageEncoder jie = JPEGCodec.createJPEGEncoder(os);
          JPEGEncodeParam jep = jie.getDefaultJPEGEncodeParam(bi);
          jep.setDensityUnit(JPEGEncodeParam.DENSITY_UNIT_DOTS_INCH);
          jep.setXDensity(1200);
          jep.setYDensity(1200);
          jep.setQuality(1, false);
          jie.setJPEGEncodeParam(jep);
          jie.encode(bi);
using ImageIO?
"Stupid" Eclipse+Maven refuse to compile this legacy code.It's an Eclipse error, not a Java/compiler error as such. To fix it, I believe you have to check your plug-in configuration -- imported packages here or exported packages there. Try adding "com.sun.image.codec.jpeg" to the imported packages. Something along those lines. Anyway, bottom line: this is not an issue with the code.
Furthermore, lookee here: GIAD

WRT160Nv3 problem with blocking traffic using Access Restrictions

Hi.
I want something quite simple. Block Youtube. I go into "Access Restrictions", choose a name for policy 1, enable it, choose the pc from the pc list, but then...
if a click Deny, all other options will be disabled (greyed out, can't click nor write on them).
Therefore, I can't put the urls I want (youtube).
I tried writing the url with "allow" and then change it to "deny" but it will block ALL traffic.
No good.
So, how do I make a new policy just to block this one URL?
Is it normal that when I click and choose "Deny" everything gets disabled afterwards?
Thanks in advance.
Regards,
Leo
Solved!
Go to Solution.

for internet access policy DENY means to restrict internet access during specified days and hours. this will block ALL internet traffic for the said schedule. website blocking by URL, blocking by means of keyword and blocking applications would then be NOT AVAILABLE as the computers would not have internet access to begin with if you have such a policy disabled.
for your case, you may want to try to set restriction to ALLOW internet access then specify youtube.com under Website Blocking by URL. this would allow computers to have access to the internet all the time (if you have the schedule set to EVERYDAY) or during specific days and hours but NOT have access to youtube.

Delays in net access restriction

Similar Messages

Maybe you are looking for