Delete Indexes Variant ended with errors in Process chain

Hi experts,
I have a process chain which executes dialy to load data Info Cube we create the index and finally we delete the index after that we have few variants..
Remaining all variants are executed with out errors except delete index variant I checked the error message it shows that " The system has not finished loading request APO_R46PWZHRIA7JS9NOM8X879QEZJ into data target ZUP_CARF1"
It is so happened weekly twice or trice not every day. one day it was running with out any errors and one day this process chan was ended with errors.
I need to know the reason why this variant was executed with errors.?
I need your valule sugestions regarding this issue.
Regards
sailekha

hi sailekha,
therevare some functional constraint of processes.
while deleting indexes
it is not possible to:
                              loading
                              indexes are being built
                              stastics are being built
                              during rollup
                              while compressing
                              while updating.
my be u can check which is the other process chain that does all above oprations in concerned infoprovider.
bye

Similar Messages

Process Chain Ended with Errors - cause unknown

I have had several instances of process chains stopping for no apparent reason. The stops occur between 2 master data infopackage loads. The last step is green and the next is grey. The PSA table has been updated successfully for the last step. All IDocs are in green status in both systems. The monitor for the last successful step does say "Ended with Errors" although no errors are evident. The process chain starts back up via Repeat at the next (grey) step and continues successfully. There were no system problems or connection interruptions that occurred during the time the process chains failed. There were no changes in the remote user profile.
This exact problem has occurred a half dozen times since our application of ECC Support Packs several months ago and had not occurred before. The infopackages are different each time. Two different process chains have had this problem. I have re-activated and re-scheduled the process chains without solving the problem.
Thanks for any ideas on why this may be occurring or what I can do to prevent it.
Patty Moffatt

Hi Des,
Here's my BW release info:
SAP_ABA        640       0019 SAPKA64019     Cross-Application
SAP_BASIS      640       0019 SAPKB64019     SAP Basis
PI_BASIS       2005_1_6400009 SAPKIPYJ69     Basis Plug-In
ST-PI          2005_1_6400008 SAPKITLQH8     SAP Solution Tools Plug-
SAP_BW         350       0019 SAPKW35019   SAP_BW
ECC SPs 13-21 were applied before the BW problem started:
SAP_BASIS      640       0021 SAPKB64021
SAP_ABA        640       0021 SAPKA64021
PI_BASIS       2005_1_6400012 SAPKIPYJ6C
ST-PI          2005_1_6400008 SAPKITLQH8
SAP_BW         350       0021 SAPKW35021
PI             2004_1_5000016 SAPKIPZI6G
The process chain step and the monitor load both are green. The Details tab shows all the processing is green, but the Process Chain itself is red with "Errors Occurred. There have been no runtime dumps.
Patty

Automatic imports throwing "tp ended with error code 0204"

Hello frnds !
In one of my non prod system, where automatic transport is enabled for 4 clients, we are getting tp error with 0204 error code in job jog of TMS_000000000*TMS_TP_IMPORT with report TMS_BCI_START_SERVICE.
Can you plz suggest someting ..
Release :
SAP_BASIS : 700 : SAPKB70013 : SAP Basis Component
Job log:
Job log overview for job: TMS_0000000005TMS_TP_IMPORT / 18003700
Job started
Step 001 started (program TMS_BCI_START_SERVICE, variant , user ID **)
Transport control program tp ended with error code 0204
Transport control program tp ended with error code 0204
Job finished
STMS errors :
System E40 Command Start TMS_TP_IMPORT
Client 000 Service Transport Service
User HP Start Hintergrund
Date 24.06.2009 Function TMS_TP_IMPORT
Time 18:00:58 Message TP_REPORTED_ERROR
Transport control program tp ended with error c
Errors: parameter is missing
System E40 Command Start TMS_TP_IMPORT
Client 000 Service Transport Service
User HP Start Hintergrund
Date 24.06.2009 Function TMS_TP_IMPORT
Time 18:00:58 Message TP_REPORTED_ERROR
************************************************************************************************************************Transport control program tp ended with error c
Errors: parameter is missing
This is tp version 372.04.40 (release 700)
Warning: Parameter DBLIBPATH is no longer used.
Warning: Parameter DBSWPATH is no longer used.
/usr/sap/trans_P40/tmp/SLOG0926.E40.LOC is already in use (1), I'm waiting 2 sec (20090624180056). My name: pid 18030 on er3asu72
(e40adm)
HALT 20090624180058
ERROR: Empty client(s) found in buffer E40. These entries cannot be filled implicitely.
Either use one of the options 'CLIENT' or 'DEFAULTCLIENT' or#use the command 'FILLCLIENT' to fill these entries with a valid client.
ERROR: EXIT(16) -> process ID is: 18030
tp returncode summary:
TOOLS: Highest return code of single steps was: 16
ERRORS: Highest tp internal error was: 0204
standard output from tp and from tools called by tp:
************************************************************************************************************************Thanks
Ashish

Hi Vikas,
Could you please check the SLOG file and see what you observe
/usr/sap/trans_P40/tmp/SLOG0926.E40.LOC is already in use (1), I'm waiting 2 sec (20090624180056).
Please check the following Note 12746 - WARN <file> is already in use (), I'm waiting 5 sec.
Mostly you have to perform the following step mentioned in Note
"If there is only one tp process that writes the SLOG messages, stop this process and copy the generated file in tmp to the existing file in log on UNIX, for example, using cat /usr/sap/put/tmp/P<date>.<SID> >> /usr/sap/put/log/P<date>.<SID>Afterwards, you can delete the file in tmp and repeat the phase."
Before trying above you can also stop all tp process and then start the transport job again.
Thank You,
Praveen

The report l runs very night and gets ended with error

Dear all,
I am facing a problem in solution manger. There is an report (Program/Command RDSMOPSOL_MONIREFRESH ) will runs very night and get ended with error and there is Run-time error "MESSAGE_TYPE_X".
Please suggest how to solve the problem.
Is this report is necessary   for the system because it is not mention in the sap stand jobs.
SM37 log
Job started
Step 001 started (program RDSMOPSOL_MONIREFRESH, variant &0000000000875, user ID BASIS)
Opening and closing session started. Session SM2000000000065
Opening and closing the session was successful. Session: SM2000000000065
Opening and closing session started. Session SM2000000000005
ABAP/4 processor: MESSAGE_TYPE_X
Job cancelled
SM:CSA SESSION REFRESH
No. Program/Command       Prog. type Spool list Parameter      User Lang.
1 RDSMOPSOL_MONIREFRESH ABAP                  &0000000000876 BASIS EN
Sm21 log
00:00:50 DIA 00 000 SAPSYS            EEA OPERATION MODES: Switch to operation mode Normal triggered
00:30:57 BTC 08 200 BASIS             R68 Perform rollback
00:30:57 BTC 08 200 BASIS             AB0 Run-time error "MESSAGE_TYPE_X" occurred
00:30:57 BTC 08 200 BASIS             AB1 > Short dump "081112 003057 sapsm BASIS " generated
00:30:57 BTC 08 200 BASIS             D01 Transaction Canceled 00 671 ( MESSAGE_TYPE_X 20081112003057sapsm BASIS 2001 )
00:30:57 BTC 08 200 BASIS             R68 Perform rollback
00:30:57 BTC 08 200 BASIS             AB0 Run-time error "MESSAGE_TYPE_X" occurred
Details
Recording at local and central time........................ 12.11.2008 00:30:57
Task................ 05312 . 08 B8 BTC background processor No. 08
User................ BASIS
Client.............. 200
Terminal............
Session............. 1
Transaction code....
Program name........
Problem class....... T    Transaction Problem
Development class... SABP
Further details for this message type
Module name......... abdynpro
Line................ 1133
Error text.......... ab_jmess
Documentation for system log message AB 0 :
The specified runtime error has occurred in the system.
Parameter
a.. MESSAGE_TYPE_X
Technical details
File................ 000048
Position............ 0000253620
Entry type.......... l      ( Error (Module, Row)            )
Message ID.......... AB 0
Variable parts...... ab_jmess                                            abdynpro1133
Time     Ty. Nr Cl. User         Tcod MNo Text                                                                    Date : 12.11.08
00:30:57 BTC 08 200 BASIS             AB1 > Short dump "081112 003057 sapsm BASIS " generated
etails
ecording at local and central time........................ 12.11.2008 00:30:57
ask................ 05312 . 08 B8 BTC background processor No. 08
ser................ BASIS
lient.............. 200
erminal............
ession............. 1
ransaction code....
rogram name........
roblem class....... K    SAP Web AS Problem
evelopment class... SABP
BAP Mini dump
ate................ 20081112
ime................ 003057
ost................ sapsm
ser................ BASIS
ocumentation for system log message AB 1 :
A short dump was generated for the specified program termination.
You can analyze this short dump in the system log evaluation by
selecting this line or evaluating Table SNAP (Transaction ST22).
echnical details
ile................ 000048
osition............ 0000253800
ntry type.......... s      ( ABAP Runtime Error             )
essage ID.......... AB 1
ariable parts...... 081112003057sapsm   BASIS
Time     Ty. Nr Cl. User         Tcod MNo Text                                                                    Date : 12.11.08
00:30:57 BTC 08 200 BASIS             D01 Transaction Canceled 00 671 ( MESSAGE_TYPE_X 20081112003057sapsm BASIS 2001 )
Details
Recording at local and central time........................ 12.11.2008 00:30:57
Task................ 05312 . 08 B8 BTC background processor No. 08
User................ BASIS
Client.............. 200
Terminal............
Session............. 1
Transaction code....
Program name........
Problem class....... K    SAP Web AS Problem
Development class... SDYN
Module name.........
Location............
T100................ 00                  671
Parameters..........
Documentation for system log message D0 1 :
The transaction has been terminated. This may be caused by a
termination message from the application (MESSAGE Axxx) or by an
error detected by the SAP System due to which it makes no sense to
proceed with the transaction. The actual reason for the termination
is indicated by the T100 message and the parameters.
Additional documentation for message 00                  671
ABAP/4 processor: &
No documentation exists for message 00671
Parameter
a.. MESSAGE_TYPE_X
00:30:57 BTC 08 200 BASIS             R68 Perform rollback
Details
Recording at local and central time........................ 12.11.2008 00:30:57
Task................ 05312 . 08 B8 BTC background processor No. 08
User................ BASIS
Client.............. 200
Terminal............
Session............. 1
Transaction code....
Program name........
Problem class....... W    Warning
Development class... STSK
Further details for this message type
Module name......... thxxhead
Line................ 1240
Error text..........
Caller.............. ThIRoll
Reason/called....... roll ba
Documentation for system log message R6 8 :
An error has causes an SAP rollback. All database updates are reset.
Technical details
File................ 000048
Position............ 0000254520
Entry type.......... m      ( Error (Function,Module,Row)    )
Message ID.......... R6 8
Variable parts......                                       ThIRollroll bathxxhead1240
Regards,
Shiva

Hi karteek,
I have check there is Switch of operation mode but when I have checked the t-code sm63 there is no new mode are in normal mode.
There is one thing I want to ask dose this report (Program/Command RDSMOPSOL_MONIREFRESH ) run   in your system or any one server because I have think there is some problem in job shued
and is also not mention in the sap stand jobs.
there is an error in sm21 in job.
BASIS        SM36 EFK BP_CHECK_REPORT_VALUES: Invalid program values found. Reason:
BASIS        SM36 EFC > Program RDSMOPSOL_MONIREFRESH has no variants, but a variant was specified
Is this SM37 log
Job started
Step 001 started (program RDSMOPSOL_MONIREFRESH, variant &0000000000875, user ID BASIS)
Opening and closing session started. Session SM2000000000065
Opening and closing the session was successful. Session: SM2000000000065
Opening and closing session started. Session SM2000000000005
ABAP/4 processor: MESSAGE_TYPE_X
Job cancelled
Sm21 log
SAPSYS            EEA OPERATION MODES: Switch to operation mode Normal triggered
BASIS             R68 Perform rollback
BASIS             AB0 Run-time error "MESSAGE_TYPE_X" occurred
BASIS             AB1 > Short dump "081111 003056 sapsm BASIS " generated
BASIS             D01 Transaction Canceled 00 671 ( MESSAGE_TYPE_X 20081111003056sapsm BASIS 2001 )
BASIS             R68 Perform rollback
BASIS             R49 Communication error, CPIC return code 017, SAP return code 223
BASIS             R64 > CPI-C function: CMINIT(SAP)
*BASIS        SM36 EFK BP_CHECK_REPORT_VALUES: Invalid program values found. Reason:*
*BASIS        SM36 EFC > Program RDSMOPSOL_MONIREFRESH has no variants, but a variant was*
specified
BASIS             R68 Perform rollback
BASIS             AB0 Run-time error "MESSAGE_TYPE_X" occurred
BASIS             AB1 > Short dump "081111 220948 sapsm BASIS " generated
BASIS             D01 Transaction Canceled 00 671 ( MESSAGE_TYPE_X 20081111220948sapsm BASIS 2001 )
Details Page 2 Line 6 System Log: Local Analysis of sapsm                     1
Time     Ty. Nr Cl. User         Tcod MNo Text
00:00:51 DIA 00 000 SAPSYS            EEA OPERATION MODES: Switch to operation mode Normal triggered
Details
Recording at local and central time........................ 13.11.2008 00:00:51
Task................ 04100 . 00 D0 Dialog work process No. 00
User................ SAPSYS
Client.............. 000
Terminal............
Session............. 1
Transaction code....
Program name........
Problem class....... S    Operation Trace
Development class... SBTC
Sm63
Start/end time   Name of the active operation mode
   00.00 - 01.00    Normal
   01.00 - 02.00    Normal
   02.00 - 03.00    Normal
   03.00 - 04.00    Normal
   04.00 - 05.00    Normal
   05.00 - 06.00    Normal
   06.00 - 07.00    Normal
   07.00 - 08.00    Normal
   08.00 - 09.00    Normal
   09.00 - 10.00    Normal
   10.00 - 11.00    Normal
   11.00 - 12.00    Normal
   12.00 - 13.00    Normal
   13.00 - 14.00    Normal
   14.00 - 15.00    Normal
   15.00 - 16.00    Normal
   16.00 - 17.00    Normal
   17.00 - 18.00    Normal
   18.00 - 19.00    Normal
   19.00 - 20.00    Normal
   20.00 - 21.00    Normal
   21.00 - 22.00    Normal
   22.00 - 23.00    Normal
   23.00 - 00.00    Normal
Regards,

Transport control program tp ended with error code 0203

when i import queue and transport queue from dev to prd ,error show:
Transport control program tp ended with error code 0203
Message no. XT200
Diagnosis
An error occurred when executing a tp command.
Command: IMPORT DEVK900298 P01 clientP01 U0 pf=/usr/sap/tra
Return code: 0203
Error text: wrong syntax in tp call
Request: DEVK900298
System Response
The function terminates.
Procedure
Correct the error and execute the command again if necessary.

Dear Allen,
The transport control program tp collects all return codes that occur when a tp command is executed. From all of these single return codes, a combined return code is calculated that tp outputs as a result at the end the command. During an import, for example, all return codes for individual import steps are handled. If a special return code does not occur, then the combined return code at the end is the maximum of individual return codes that occur. In addition to the value of the return code, tp also gives a short description of this return code. You can display this short description using the command explainrc.
Normally, all return codes that occur originate from individual transport steps. Since these individual return codes can only have the following values 0, 4, 6, 8, 12, 13, 14, 16, the combined return code also has one of these values. However, if a general error occurs, a single return code over 200 is generated. For example, this could arise if tp cannot establish a connection to the database. The maximum return code for all single transport steps is output in a separate message before specifying the combined returned code. In this case, the combined return code is always the return code of the general error message.
tp Commands:
tp addtobuffer <request> <sapsid>
As of Release 4.6A, an explicit addtobuffer command leaves the position of the entry unchanged, if the relevant transport request is already in the buffer. Only the status of the entry is changed:
Unconditional modes appearing in the command line are added to the unconditional modes in the buffer.
All the steps of the entry are re-initialized.
If the entry found is not an initial entry, the import step for the command file is set to *4000 .
Before you call this command and its options, consider the effects of changing the import sequence.
tp cleanbuffer <sapsid>
This deletes successfully imported change requests from the list of requests that are marked for import into the SAP System <SAPSID>. This function is contained in the commands tp import all <sapsid> and tp put <sapsid> .
tp delfrombuffer <request> <sapsid>
If the specified request is marked for import into the specified SAP System, this flag is deleted from the import list.
Before you call this command, consider the effects of changing the import sequence.
As of Release 4.6A: If a transport request was only partially imported, you can delete this type of transport request from the buffer. However, if a deleted transport request is placed in the buffer (without having been initially or completely imported), the attributes of the old entry are reactivated. This means the return codes, the unconditional modes and tags of the deleted entry appear in the new entry.
tp delstopmark <sapsid>
If the list of requests marked for import into the specified SAP System contains a STOP mark, the mark is deleted.
tp export <request>
This exports the complete request from the source system. This command starts the export of a request from the operating system level. Only use this command in exceptional cases. The SAP System uses the command expwbo to release requests from CTS transactions.
tp reformatbuffer <sapsid> [options]
This automatically reformats the entire buffer.
As of Release 4.5A, there are 2 different formats for buffer entries. (As of Release 4.5A, tp can work with both formats, and with a puffer containing heterogeneous entries. As of Release 4.6A, tp can work with 3 formats.)
However, in certain cases entries with the old formatting have to be reformatted during the normal run of tp . In this case, the entire buffer is automatically reformatted.
If you use the options downtorelease and Iagree for command reformatbuffer , you can format the buffer so that its formatting is compatible with an older release:
Option downtorelease <Release>
The command reformatbuffer with this option formats the buffer so that the formatting corresponds to the one used in an old release. This is necessary if tp writes buffer entries to the buffer of another system, but uses a buffer format that the transport control programs does not understand in this system.
Since older formats cannot store the same amount of information as the newer ones, some information contained in the original buffer may not be stored in the unformatted buffer. This may lead to data loss.
To avoid data loss, the original buffer is stored. In addition, you have the following functions:
Displaying the unformatted buffer (using showbuffer <SID> )
Displaying the original buffer (using showbuffer buffer=<SID>SAV )
Accepting the unformatted buffer (using reformatbuffer and the option Iagree yes )
Resetting the changes (using reformatpuffer and the option Iagree no )
If you call reformatpuffer using downtorelease , tp displays in detail if information was lost by reformatting, and what that information was. tp also names the commands that is has to execute to accept or reject the changes.
If you use the option downtorelease , you must also specify the option Iagree with yes or no . You cannot use the transport system until you decide to accept or reject the changes.
Option Iagree
Here are the following values for this option:
yes ( true )
Accept the change made by tp reformatbuffer <SID> downtorelease <rel>
In this case, tp deleted the buffer semaphore file that was lifted for security reasons at the first call of reformatbuffer
no ( false )
Reject the change made by tp reformatbuffer <SID> downtorelease <rel> In this case, tp copies the backup of the original buffer back and deletes the buffer semaphore file that was lifted for security reasons at the first call of reformatbuffer
tp setstopmark <sapsid>
A special STOP mark is added to the list of requests registered for import into the specified SAP System. The commands tp import all <sapsid> and tp put <sapsid> only process the requests in front of this stop mark.
If there is no stop mark, it is automatically generated by the commands
tp import all <sapsid> and tp put <sapsid> .
When all the requests in front of the stop mark have been imported successfully, at the end of all the calls the related marks and the mark itself are deleted.
A STOP mark can only be placed at the end of the change requests that have already been marked. In addition, it can only be set if no other mark of the same kind already exists.
tp showparams <sapsid>
This tp function displays which values the individual parameters of the transport profile have for the current SAP System.
tp verse <request>
This creates versions of the objects in the specified request. This transport step is contained in command export .
As of Release 4.5A, more actions that prepare the export are performed in this step.
Thanks and Regards,
Naveen.

SQL Plus & End with Errors

In my Process Flow I have a SQL Plus activity that calls a custom DML Express program. How would I trigger the End with Errors activity if my custom DML program errrors out? Currently my SQL Plus activity is as follows:
--SET SERVEROUTPUT ON
-- PL/SQL
DECLARE
v_cmd VARCHAR2(500);
BEGIN
DBMS_AW.AW_ATTACH('AW', true);
DBMS_AW.EXECUTE('cda logfiles_dir');
v_cmd := 'Call CUSTOM_DML_PROG';
DBMS_AW.EXECUTE(v_cmd);
DBMS_AW.AW_DETACH('AW');
end;
quit
Is there a way to pass a parameter from my DML Express program to the SQL Plus activity that could somehow trigger End with Errors?
Kristine

Hi David,
I have been able to run this process flow that calls my DML program several times however, I am now receiving the following errors:
RPE-01003: An infrastructure condition prevented the request from completing.
RPE-01038: Failed to evaluate expression declare "$LOOP_DETECT$" NUMBER := 0;function...
My function returns a Number and my transformation in the process flow has been defined as having Integer as the Data Type and by default the Literal value is True.
The complex condition has been defined as the following:
"CALL_GS_MTH_END_GL_ACT1"."CALL_GS_MTH_END_GL_ACT1" =0
Any ideas as to why all of a sudden I receive this error? I have been able to workaround this issue by deleting the transformation from the process flow, adding it back and re-deploying the process flow however this is not ideal.
Kristine

Online backup by DB13 ended with error not by BRTOOLS

Dear Friends,
I am trying to take online backup by DB13 of my CRM Dev system but it is ended with error , but when i check in SM37 it show finished.
By using BRTOOLS it work proparly but not by DB13.
Other Details :-
OS :- Win 2003 server
DB :- Oracle 10g
error message is :-
Detail log: bdxbnwwr.ant
BR0051I BRBACKUP 7.00 (26)
BR0055I Start of database backup: bdxbnwwr.ant 2008-01-19 10.48.21
BR0484I BRBACKUP log file: F:\oracle\CD1\sapbackup\bdxbnwwr.ant
BR0252W Function remove() failed for 'f:\oracle\cd1\102\database\sap.ora' at location BrInitOraCreate-1
BR0253W errno 13: Permission denied
BR0252W Function remove() failed for 'f:\oracle\cd1\102\database\sap.ora' at location BrInitOraCopy-7
BR0253W errno 13: Permission denied
BR0166I Parameter 'control_files' not found in file f:\oracle\cd1\102\database\initCD1.ora - default assumed
BR0252E Function CreateFile() failed for 'G:\ORACLE\CD1\SAPDATA3\TEMP_1\TEMP.DATA1' at location BrFileStatGet-2
BR0253E errno 5: Access is denied.
BR0273E Determination of file status for G:\ORACLE\CD1\SAPDATA3\TEMP_1\TEMP.DATA1 failed
BR0314E Collection of information on database files failed
BR0056I End of database backup: bdxbnwwr.ant 2008-01-19 10.48.45
BR0280I BRBACKUP time stamp: 2008-01-19 10.48.45
BR0054I BRBACKUP terminated with errors
So please help on this issue and reply ASAP.
Thanks,
Regards,
Sachin Jadhav
BASIS

Hello Friends,
I m facing one problem while taking backup form db13. can sombuddy help me to solve this problem following is the log file details
Job started
Step 001 started (program RSDBAJOB, variant &0000000000011, user ID BASIS)
Execute logical command BRBACKUP On host eccqa
Parameters:-u / -jid FLLOG20081015143102 -c force -t online -m full -p initIEQ.sap.wed -a -c force -p initIEQ.s
ap.wed -s
BR0051I BRBACKUP 7.00 (32)
BR0055I Start of database backup: bdzapxni.fnd 2008-10-15 14.31.02
BR0484I BRBACKUP log file: /oracle/IEQ/sapbackup/bdzapxni.fnd
BR0280I BRBACKUP time stamp: 2008-10-15 14.31.02
BR0301E SQL error -27140 at location BrDbConnect-2, SQL statement:
'CONNECT /'
ORA-27140: attach to post/wait facility failed
BR0310E Connect to database instance IEQ failed
BR0280I BRBACKUP time stamp: 2008-10-15 14.31.02
BR0301E SQL error -27140 at location BrDbConnect-2, SQL statement:
'CONNECT /'
ORA-27140: attach to post/wait facility failed
BR0310E Connect to database instance IEQ failed
BR0056I End of database backup: bdzapxni.fnd 2008-10-15 14.31.02
BR0280I BRBACKUP time stamp: 2008-10-15 14.31.02
BR0054I BRBACKUP terminated with errors
BR0280I BRBACKUP time stamp: 2008-10-15 14.31.02
BR0291I BRARCHIVE will be started with options '-U -jid FLLOG20081015143102 -d disk -c force -p initIEQ.sap.wed -s'
BR0002I BRARCHIVE 7.00 (32)
BR0006I Start of offline redo log processing: adzapxni.sve 2008-10-15 14.31.02
BR0484I BRARCHIVE log file: /oracle/IEQ/saparch/adzapxni.sve
BR0280I BRARCHIVE time stamp: 2008-10-15 14.31.02
BR0301W SQL error -27140 at location BrDbConnect-2, SQL statement:
'CONNECT /'
ORA-27140: attach to post/wait facility failed
BR0310W Connect to database instance IEQ failed
BR0280I BRARCHIVE time stamp: 2008-10-15 14.31.02
BR0301W SQL error -27140 at location BrDbConnect-2, SQL statement:
'CONNECT /'
ORA-27140: attach to post/wait facility failed
BR0310W Connect to database instance IEQ failed
BR0278W Command output of '/oracle/IEQ/102_64/bin/sqlplus /nolog < /oracle/IEQ/saparch/.adzapxni.spi':
SQL*Plus: Release 10.2.0.2.0 - Production on Wed Oct 15 14:31:02 2008
Copyright (c) 1982, 2005, Oracle. All Rights Reserved.
SQL> Connected to an idle instance.
SQL>
SQL> ORA-01034: ORACLE not available
SQL> Disconnected
BR0280I BRARCHIVE time stamp: 2008-10-15 14.31.02
BR0279W Return code from '/oracle/IEQ/102_64/bin/sqlplus /nolog < /oracle/IEQ/saparch/.adzapxni.spi': 0
BR0302W SQLPLUS call for database instance IEQ failed
BR0323W 'Archive log list' for database instance IEQ failed
BR0252E Function fopen() failed for '/oracle/IEQ/saparch/archIEQ.log' at location arch_last_get-1
BR0253E errno 13: Permission denied
BR0016I 0 offline redo log files processed, totalsize 0.000 MB
BR0280I BRARCHIVE time stamp: 2008-10-15 14.31.02
BR0301W SQL error -27140 at location BrDbConnect-2, SQL statement:
'CONNECT /'
ORA-27140: attach to post/wait facility failed
BR0310W Connect to database instance IEQ failed
BR0252W Function fopen() failed for '/oracle/IEQ/saparch/archIEQ.log' at location BrCleanup-8
BR0253W errno 13: Permission denied
BR0121W Processing of log file /oracle/IEQ/saparch/archIEQ.log failed
BR0007I End of offline redo log processing: adzapxni.sve 2008-10-15 14.31.02
BR0280I BRARCHIVE time stamp: 2008-10-15 14.31.02
BR0005I BRARCHIVE terminated with errors
BR0280I BRBACKUP time stamp: 2008-10-15 14.31.02
BR0292I Execution of BRARCHIVE finished with return code 3
External program terminated with exit code 3
BRBACKUP returned error status E
Job finished
it showing me above messege every time ..
Thanks
Vijay

STMS: Transport control program tp ended with error code 0232

Dear ERP Gurus,
I just encountered problem with STMS in my PRD system. The import is just stuck up on "tp connecting to database". It won't continue unitl the system gives me this error message:
Transport control program tp ended with error code 0232
Errors: connect failed
The tp System log says:
ERROR: Connect to PRD failed (20090227135454, probably wrong environment)
I have verified that the suggestion in SAP Note 165708 has already been implemented in our DEV, QAS, and PRD instances.
Any idea why I am having this problem? Imports were running fine yesterday. Please help.
Your prompt response is highly appreciated.
Thanks a lot.
Best Regards,
Albert

Hi Albert,
First check import monitor and delete all requests from queue, which are still getting imported.
And go to /usr/sap/trans/tmp and mv all those tmp files to other location.
Then kill all OS jobs which are getting execute with tp.
Check all jobs are runnig fine, related to transportation. If not reschedule the same.
Then start importing.
Before doing this just check whether your stms related RFCs are working fine.
I think One of your RFC is getting struck. just try to change ip or hostname accordingly and try.
Regards
Nick Loy

Transport Controll Program tp ended with error code 0012

we have 3 instances 1 DEV 2 TEST 3 PROD.
in TCODE:STMS by clicking 'system overview' icon
all systems are showing and domain controller is PROD,
and Test System also defined as Transport Domain Cotroller.
earlier STMS scenario: Transport Route is from DEV to PROD system not to the TEST system.
what I have done:
deleted the Transpor Domain Controller of the TEST system and kept as test system.
create routes from DEV to TEST to PROD.
present STMS problem:
when I am sending Request from the DEV to TEST Request going smootly. but at TEST sytem while importing the Request it is giving the ERROR as "Transport control program tp ended with error code 0012"
please help out me....as soon as possible.

This is definitely the wrong forum for your post. Please repost properly.
Regards, Klaus

Transport control program tp ended with error code 0249

Hello guys,
I am facing an when importing transport. After I click import to the transport in STMS, before it runs, a message window is displayed immediately. This was working find until last week, any kind of transport is followed by the same error.
Transport control program tp ended with error code 0249
Message no. XT200
Diagnosis
An error occurred when executing a tp command.
Command: IMPORT BWDK903312 BIW client200 U0 pf=
sapbiw1a\s
Return code: 0249
Error text: connect failed due to DbSL load lib failure
Has anyone faced this error while trying to import a transport? I have not found the same error in sdn (0249)
help will be appreciated.
thanks
DGF

Your are right, but which is the Basis forum?
Business Process Expert
Database & OS Platforms ABAP Development
Enterprise SOA Portal
Emerging Technologies
SAP Solutions
Business Intelligence
Scripting Languages
SAP Business One Industries
Community Discussions
SAP NetWeaver Application Server Integration and Certification Center (ICC)

Transport control program tp ended with error code 0016

Hello colleagues,
We are getting the following error when exporting system HRP to HRI:
Transport program TP started successfully for HRPKX00005 21:25:45
|   Transport control program tp ended with error code 0016
|   Error exporting request HRPKT00005 00:59:50
|   Program ended with error or warning, return code: F
|   Runtime (seconds)         :         13.876
|   End of processing: 00:59:50
Please could you kindly help us to solve the issue?
Thanks in advance.
Best regards
Edited by: Víctor Barahona Cimas on Nov 12, 2009 3:33 PM

ok thanks

Transport control program tp ended with error code 0212 | URGENT

Hi All,
 We are trying to import requests in our PRD system. As soon as we select the request and try to import it , we get the error "Transport control program tp ended with error code 0212".
This is tp version 305.12.42 (release 46D) for ANY database
/usr/sap/trans/cofiles/K915883.<SID> for transport: <SID>K915883: Permissio
HALT 20070222114323
ERROR: /usr/sap/trans/cofiles/K915883.<SID> : cant open
: Permission denied
ERROR: EXIT(16) -> process ID is: 6878
tp returncode summary:
TOOLS: Highest return code of single steps was: 16
ERRORS: Highest tp internal error was: 0212
Output from tools called by tp:
This is R3trans version 6.05 (release 46D - 18.10.01 - 11:30:00).
R3trans finished (0000).
When i checked the transport tool and rfc destinations, everything was successful.
When i tried to do tp connect -
23> tp connect <SID> pf=/usr/sap/tran/bin/TP_DOMAIN_<SID>.PFL
This is tp version 305.12.42 (release 46D) for ANY database
E-/usr/sap/tran/bin/TP_DOMAIN_<SID>.PFL could not be opened.
EXIT
tp returncode summary:
TOOLS: Highest return code of single steps was: 0
ERRORS: Highest tp internal error was: 0212
tp finished with return code: 212
meaning:
could not access file as supposed (see SLOG for more details)
We are having SAP 4.6C with DB -Oracle and OS HP-UX.
Please let me know whow to rectifiy the issue. The situation here is getting worse.
Regards,
NK

Hi Ruchit, Sorry for the delay. Here is the file you wanted -
steic25q:root>ls
DOMAIN.CFG TPPARAM.bak TP_DOMAIN_ID1.PFL TP_DOMAIN_IQ1.PFL
TMS_TEST.IS1 TPPRAMA0918 TP_DOMAIN_ID1.orig nik.dev_evt
TPPARAM TP_DOMAIN_ID1.BAK TP_DOMAIN_IP1.BAK
steic25q:root>more TP_DOMAIN_ID1.PFL
#TMS:0078:DOMAIN_ID1
Caution !
This file was generated by the Transport Management System.
Do not change this file using a text editor.
For more information, refer to the online documentation of the
Transaction STMS.
If this file was destroyed, it can be regenerated in the TMS.
To do this, log on to the domain controller (system ID1) and call
transaction STMS. In the System Overview, you can distribute the TMS
configuration. This regenerates the file.
STMS -> Overview -> Systems -> Extras -> Distribute TMS configugration
TRANSDIR = /usr/sap/trans
DU1/CTC = 1
DU1/DUMMY = 1
DU1/NBUFFORM = 1
DU1/TP_VERSION = 266
DU2/CTC = 1
DU2/DUMMY = 1
DU2/NBUFFORM = 1
DU2/TP_VERSION = 266
ID1/CTC = 0
ID1/DBHOST = steic24q
ID1/DBLIBPATH = /usr/sap/ID1/SYS/exe/run
ID1/DBNAME = ID1
ID1/DBSWPATH = /oracle/ID1/817_64
ID1/DBTYPE = ora
ID1/NBUFFORM = 1
ID1/TP_VERSION = 266
IP1/CTC = 0
IP1/DBHOST = steic25q
IP1/DBLIBPATH = /usr/sap/IP1/SYS/exe/run
IP1/DBNAME = IP1
IP1/DBSWPATH = /oracle/IP1/817_64
IP1/DBTYPE = ora
IP1/NBUFFORM = 1
IP1/TP_VERSION = 266
IQ1/CTC = 1
IQ1/DBHOST = cbnysap2
IQ1/DBLIBPATH = /usr/sap/IQ1/SYS/exe/run
IQ1/DBNAME = IQ1
IQ1/DBSWPATH = /oracle/IP1/817_64
IQ1/DBTYPE = ora
IQ1/NBUFFORM = 1
IQ1/TP_VERSION = 266
TRN/CTC = 1
TRN/DUMMY = 1
TRN/NBUFFORM = 1
TRN/TP_VERSION = 266
steic25q:root>

Re: Transport control program tp ended with error code 0212

Hi ,
When transport request is added to import queue, getting following error :
"Transport control program tp ended with error code 0212 "
Please find the slog file description as follows:
HALT 20110530001050
ERROR: /usr/sap/trans/cofiles/K904416.<SID>: cant open
: Permission denied
ERROR: EXIT(16) -> process ID is: 2273
HALT 20110530004629
ERROR: /usr/sap/trans/cofiles/K904416.<SID> : cant open
: Permission denied
ERROR: EXIT(16) -> process ID is: 14341
HALT 20110530004703
ERROR: /usr/sap/trans/cofiles/K904416.<SID> : cant open
: Permission denied
ERROR: EXIT(16) -> process ID is: 14514
How to correct this ?
Thanks
Srikanth

Hi,
It may happen happen due to permission issue when you are having SAN and sharing common trans directory now to check the permission of the file you have to login at os level and check the permission of the TR.
cd /usr/sap/trans/cofiles/
ls -l K904416<SID> - now here it will show the permission of the file please paste the output
Thanks,
Saleem

Releasing a Transport Request ends with error code 0012.

Hi,
We have a Development system and a Production System (both running on separate windows machine) but they are not connected in STMS. We perform transporting of Requests at o.s level and NOT through STMS.
We are facing this new problem - We are trying to release a Transport Request in SE01 and it ends with error code 0012. The task inside the Request is released without any error. There is no Notes in SAP Marketplace for this.
Test call of transport control program (tp) ended with return code 0012
Message no. TK094
Diagnosis
Your transport request could not be exported, since all requirements were not fulfilled.
Calling the transport control program tp
"tp EXPCHK EFIK900025 pf=E:\usr\sap\trans\bin\TP_DOMAIN_EFI.PFL -Dtransdir=E:\usr\sa"
which checks the export requirements, returned the following information:
Return code from tp: 0012
Error text from tp: ERROR: Buffer check failed.
System Response
Further processing is terminated.
Procedure
Check the following points:
Feasibility of the transport control program tp
Parameter settings in the transport profile
Availability of the transport directory and the subdirectories (cofiles, data, log, sapnames, bin)
Write authorization for the subdirectories
Write authorization for the files of the subdirectories cofiles, data, log, sapnames
Release the request again when the error has been removed
Please help.
Regards,
Mohan.

Hi Mohan,
Nice to hear that that your problem is resolved.
For Pamater CTC, please check the below links:
Automatic transport between DEV clients ?
http://sapsolutions.searchsap.com/kw;ExtendedTransportControl/content-sap.htm
Regards,
Hari Kishan

Plz.. Help me..... Concurrent program ended with errored.

hi alll....
I am on working on Oracle Audit trail for mtl_system_item_b (ie. whenever item is changed, created or deleted , i want to track the data, who delete that item and wat item). I followed the below steps to perform that.
Steps 1:
sysadmin ->Security : AuditTrail->install. I checked weather audit trail is enabled for oracle inventory (ie, in screen i query for inv under oracle username tab and checked weather enabled box is checked).
Steps 2:
Creation of Audit group
navigation : AuditTrail ->Groups.
Application Name: Oracle Inventory
Audit Group: XX inventory
Group State: Enabled
I added audit tables to this group
User Table Name: MTL_SYSTEM_ITEMS_B
Steps 3:
After creation of audit group i run the Concurrent program “*AuditTrail Update Tables*” . It has no parameter..
The request is ended with errored when i ran. Plz help me... Its urgent.
I checked with log file too. It has so many page. finally it displaying
fatal error in fdasql,quitting...
fatal error in fdacv,quitting...

Hi,
Search the log file for more details about the error.
You may also review these documents and see if it helps.
Note: 353326.1 - Audittrail Update Tables : Fatal Error In Fdasql,Fdacv,Fdaupc When Create View
https://metalink2.oracle.com/metalink/plsql/ml2_documents.showDocument?p_database_id=NOT&p_id=353326.1
Note: 563116.1 - AuditTrail Update Tables Program Fails with "Fatal error in fdasql, quitting..."
https://metalink2.oracle.com/metalink/plsql/ml2_documents.showDocument?p_database_id=NOT&p_id=563116.1
Regards,
Hussein

Delete Indexes Variant ended with errors in Process chain

Similar Messages

Maybe you are looking for