Dell laptop internet connection airport express
We are using Airport Express to connect to the internet. It works with our iMac & we are also able to print wirelessly with the iMac.
We are having difficulty connecting a Dell laptop to the internet using the same Airport Express. We're not sure how to set it up.
We previously used a router and a PC with the Dell laptop.
Please advise us on how to set this up.
iMac Mac OS X (10.4.9)
L&S, Welcome to the discussion area!
Perhaps you can find a solution on iFelix's site. If not, you can post in the AirPort for Windows discussion area.
Similar Messages
-
I can't connect Airport Express wirelessly to network so that AirTunes and internet are available simultaneously. My old AE allowed this but can't make the new one work that way.
In your instructions, you say to use the same encryption type as the router has set up. well, I am using the WEP 64 bit encryption and the Airport Utility does not have this...it has 40 bit. Is this a problem, or do I have to be using a the same type of encrytion ?
WEP is available in either 40 or 104-bit, but is usually "advertised" as either 64- or 128-bit respectively. For example, 64-bit WEP uses a 40 bit key (also known as WEP-40), which is concatenated with a 24-bit initialization vector (IV) to form the 64-bit RC4 traffic key. So, WEP 64 on the Linksys & 40-bit is equivalent.
What concerns me more is the loss of bandwidth performance you are experiencing when connecting the AX. When the AX is configured as a wireless client it is acting just like any other wireless devices (computer, laptop, printer, etc.) and not like another router. This should cause little or no bandwidth loss. True the more secure the wireless encryption used WPA2 vs. WEP, the more overhead is required for security, but the differences you are seeing seem excessive.
It is very possible that you may have some form of Wi-Fi interference in the immediate area that is preventing your Linksys from providing a good clean signal.
I suggest you perform a simple site survey, using utilities like the following to determine potential areas of interference, and then, try to either eliminate or significantly reduce them where possible:
For Macs:
o MacStumbler
o iStumbler, or
For PCs:
o NetStumbler -
Can't connect to internet through Airport Express anymore
Suddenly, my PowerBook can't connect to the internet through Airport Express. Monday late afternoon--everything was fine. Put it in sleep, come back a few hours later, can't connect.
Thing is, Airport/wireless is working. Can stream audio to my home stereo.
And the DSL/modem are working. If I connect the machine via ethernet directly, I'm online.
Saw that some other users began having problems with USB/printer connections Monday. Could my problem be related?
What gives?
Any ideas?Hello mnkyby. Welcome to the Apple Discussions!
It sounds like your AirPort Express Base Station (AX) in not getting a proper IP address from your modem.
Try this ...
o Connect to the AX's wireless network, and then, run the AirPort Admin Utility.
o Go to the Internet tab.
o Note the value for IP address. (Note: Do not list it here on the forum, just note what it is.)
o Is the IP address what you would expect from your ISP or is it something like: 196.254.x.x?
If the latter, try the following ...
Modem/Router Power Recycling - Quick
o Power-off the DSL/Cable modem, AX, & computer(s); Wait at least 5 minutes.
o Power-on the DSL/Cable modem; Wait at least 5 minutes.
o Power-on the AX; Wait at least 5 minutes.
o Power-on the computer(s)
If this fails to get the modem to "recognize" the Internet router, then try the "Full" version.
Modem/Router Power ReCycling - Full
o Power-off the DSL/Cable modem, AX, & computer(s). (Wait at least 30 minutes. If possible, leave the modem off overnight.)
o Power-on the DSL/Cable modem; Wait at least 15 minutes.
o Power-on the AX; Wait at least 5 minutes.
o Power-on the computer(s) -
Cannot connect Airport express wireless
Hello, cannot connect airport express wireless to linksys router. Connected now with ethernet cable but cannot figure wireless connection. My laptop cannot find the express while preforming setup scan, yet I'm connected to it. I can connect with my iphone but not wirelessly. Any suggestions?
....I was then told over the phone that airport express will not connect to third party routers.
This is NOT correct.
The AirPort Express will connect to a wireless network if you know the following:
1) The name of the wireless network
2) The exact setting for wireless security that the network is using
3) The wireless network password
Most users know 1) and 3), but very few know the exact type of wireless security settings that their wireless router is using. The Express will not connect to the wireless network unless it receives all of the information listed above.
So...we will assume that you know the name of the wireless network and the password for the network.
Do you know the exact type of wireless security setting that your wireless router is using? If not, the Express will not connect.
You may need to check the setup of your wireless router....or if the router was supplied to you by an Internet Service Provider, they may be able to tell you what type of wireless security setting is being used.
Post back when you have this info and we will proceed. There are still no guarantees that the Express will connect....but at least there may be a chance. -
How to Connect Airport Express to Existing Wireless Network (Client Mode)
I am posting this for everyone tearing their hair out trying to connect the Airport Express to your own existing home wireless network. After spending 2 hours last night installing this on my father-in-law's home network, I hope to be able to save someone else the agony we went through.
So here's the situation:
Say you already have your own home network set up, and all you want is to be able to use AirTunes to play music off iTunes into your speaker system. And, you don't need the printer sharing capability nor creation of another wireless network (2 of the features of Airport Express). Then this solution is for you - read on.
Unfortunately, Apple's user manual is very unclear how to connect Airport Express to your own network. When you look at the picture diagram they provide, they show Airport Express picking up its signal from another Apple-oriented base. This can make you think you need to buy another piece of hardware to make it work. DON'T If you read through the manual, the Support section here, etc., you will hear lots of talk about "Client Mode" - and that this is the only way to get it to work. Nice - but no one really tells you how to set up the Airport in client mode.
Do yourself a favor, toss that user manual aside and run these steps.
(Note: These directions assume your DSL/Cable Modem is hooked up to a wireless router or acts as its own wireless router)
1. Get a cat5 Ethernet cable (anything but an orange cable - that's a crossover cable) like you would use to connect your PC to your router to pick up the Internet.
2. Connect the Ethernet cable to the router on one end, and to the Airport Express unit on the other end.
3. Plug in your Airport Express unit to the wall (this will not necessarily become its permanent location - you will be able to move it later). The light will glow solid Amber for about 30-45 seconds while it starts up, then blink Amber. At this point, the unit is ready to operate.
4. Install the CD to the PC where your iTunes music is stored. This should be painless. Once you open the program, it should detect the Airport unit.
5. At this point, the on-screen wizard will present you with your options, and walk you through the setup. This is much like the user manual describes - and you should be good to go form here forward.
Some pointers:
- When asked if you want to create a new network, join an existing network, or connect via Ethernet, choose the middle option for joining an existing network. You will need to know the name of your network, the password to connect to the network (if present), and the type of encryption used on the network (e.g. WEP, WPA, etc.). Side note, WPA is recommended, as it is a higher level of security than WEP. You will be able to configure the Airport Express unit to automatically login to your network.
- I would recommend, when creating a password for the Airport Express unit, use the same password as your network, to avoid confusion.
6. The very last step will ask you to save the settings to the Airport Express. Here's the kicker - when you save the settings, you are TRICKING the Airport Express into no longer acting as a network broadcaster, but instead being a "slave" to your own network. What do I mean? You will lose the connection from your PC to the Airport Express - an error message will pop up telling you the unit can no longer be found. While you might think you did something wrong, you actually were successful!
7. Unplug your Airport Express, and disconnect the Ethernet cable from your router and the Airport unit. This will no longer be needed.
8. Go to your desired location where you want to plug in your Airport Express unit. Before plugging it in, connect your Audio cable from the Airport Express to your audio receiver. Once that is connected, then plug in the Airport Express unit. The light will glow solid Amber for 30-45 seconds while it loads, and then will blink Amber for a brief period of time before turning solid GREEN. When this happens, you have successfully connected the Airport Express to your home network!
9. Go back to your PC with iTunes. Open the Airport software - you should now have a listing for your Airport Express unit in the upper left. Click on this, and the wizard will guide you through connecting - you will need the password you created for the unit. You only need to go through this wizard once, and when finished, the software will tell you that can now use iTunes with your Airport unit.
10. Open iTunes. On the lower right, you will see a dropdown for Speakers, and it should be defaulted to My Computer. Click on that drop-down, and you will see the name of your Airport unit. Click on that name, and now your music will broadcast to the Airport unit!
11. Play a song in iTunes. Go to your audio receiver, and connect it to the channel for your external connection to the Airport Express unit. You should hear your music from iTunes. CONGRATULATIONS! =)
I hope these instructions were helpful - I am happy to answer any questions, so feel free to contact me, *******************@*****.**.
<Edited by Moderator>Thanks for the detailed directions. You are absolutely correct in stating that people should toss the user manual; it's pretty worthless. I have had a problem setting up my new Airport Express as I have described in an earlier post - http://discussions.apple.com/thread.jspa?threadID=1839873&tstart=45
One quick question - does using your setup process set the AE up as part of a distributed network where the AE is acting as a wireless router where it is extending the range of your network? Or, is it simply a wireless connection to your stereo for iTunes? I am interested in having both, since my AE will be at the other end of the house from the main wireless router.
Thanks -
How do i connect airport express to blue ray player
wondering if i can connect airport express to blue ray player using usb for streaming, etc?
Good question. The single port on the AirPort Express places it somewhat at a disadvantage in a situation like this. It's tempting to think that a setup like this will work:
Modem > Ethernet Switch > Express & Blu-Ray Player both connected to the switch
But, unfortunately, it won't. The reason is that the modem has only one IP address it can deliver and it can't go to two devices at the same time. It will be matter of chance as to which device...the Express or Blu-Ray Player....gets the IP address. The other device will not be able to connect to the Internet.
Instead, what is required is a simple "wired only" router connected to the modem. So the corrrect setup will look like this:
Modem > Wired Only Router > Express and Blu-Ray Player both connected to the router
The router "shares" the IP address that it receives from the modem (an ethernet switch cannot do this) and provides simultaneous Internet connections to the devices that are plugged into the ethernet ports on the router. -
when trying to connect airport express keep getting unexpected error please try again. IVE TRIED A HUNDRED TIMES AND HAVE FOUND SUPPORT PAGES UNHELPFUL
Have you tried using a WEP password for your wireless network instead of a WPA one? That fixed it for me.
-
cannot connect airport express to ipad
I keep receiving the message: "an unexpected error occurred" when I try to connect my Ipad to my airport express. Does anyone have a solution?I could not "see" my Express via my wireless router or via the Airport Utility until I reset it to Factory Settings by unplugging it then holding in the tiny reset button while plugging it back in, waiting for the flashing yellow LED signal before letting go.
Then I set it up to DHCP - "connect to wireless network" and DOWNGRADED the firmware to 7.3.x
I would tell you the exact Firmware but I can no longer "see" the Airport express............ AGAIN or still.....
BUT at least I am listening to music streaming from my MacBook Pro... Hmmm.
I log back into the router (Linksys WRT110) and it no longer shows the Airport Express as a DHCP client AND the Airport utility can no longer "find" any Airport Devices..
So if I don't move, or there are no cosmic events, or maybe my KARMA is effecting the device or my "VIBES" are good, but I'm not sure if will continue to work.. Sure would like to use this little device from hel*.
Since I have had this Airport Express I have spent many hours trying to get it to work.
It works just long enough to fool me and then takes a dump...
Maybe this time?
5 Minute later...
Music was playing. I went into iTunes and switched from Airtunes to Computer speakers. When I tried to switch it back GUESS WHAT?
[An unknown error (-15006) occurred while trying to connect to remote speaker "Airtunes"]
Wonderful Green LED though. Totally useless piece of equipment AFAIK.
Message was edited by: Daniel Shattuck -
Connect airport express to router wifi not apple
I already have a wifi router is not Apple, I have already configured iPhone and iMac to wirelessly, now I need to connect my hi-fi via an airport express (via wifi of course) I can connect "airport express" to a wifi router does not Apple via wifi?
now I need to connect my hi-fi via an airport express (via wifi of course) I canconnect "airport express" to a wifi router does not Apple via wifi?
Yes, the AirPort Express can "Join" virtually any wireless network if you know the name of the network, the exact type of wirelss security that is being used on the network and the wireless network password.
The Express will work for AirTunes and/or allow you to connect a printer when it is configured this way.
But....the Express cannot provide any additional wireless coverage for the network when it is configured to "Join" the network, so it will not "repeat" or "extend" the wireless network in this type of setup. -
While connecting airport express, the airport utilities shows airport express but no set up menu
trying to connect airport express for music streaming. already have time capsule. Airport utilities show airport express but no setup options at all.
What version of AirPort Utility do you have?
Please look on the side of the AirPort Express for the model number.....starts with an "A" followed by four numbers.......and post back with that info. -
Windows laptop won't connect to internet using airport express connection
Hi. I don't know what I'm doing wrong. I set up airport express on my imac g5 so I could share the internet with my windows laptop. I have a wireless notecard plugged into my laptop (802.11gg)--the laptop recognizes a wireless network with my imac no problem. I'm able to access the internet with my imac, but my laptop can't. I have a cable modem with the ethernet cable attached to airport express. I set up the wireless network using wep. Am I missing something? Please help! Thanks!
I had a similar issue this morning. My problem was my password. Apple will allow short passwords with wep encryption. Other manufacturer's don't.
"The multiplatform issue
Being an older protocol, WEP password treatment was not implemented uniformly by all wireless hardware and operating system manufacturers. Some products require users to enter relatively cryptic hexadecimal characters (four bits each), while others allow "plain language" password entry. A plain language password, like "apple", uses standard ASCII characters that are 8 bits each.
Products that allow plain language (ASCII) password entry may not force the network administrator to create 5- or 13-character passwords that would result in the required 40 (5*8) and 104 (13*8) bit-length passwords. Instead, they use a "hashing" routine to convert an odd-length password to the correct bit length. The multiplatform issue arises when the hashing results of products from two different manufacturers don't match each other. The resulting "network equivalent passwords," which are always given in hexadecimal format, are different."
In my case I made the password 13 characters long and everything works fine now.
http://docs.info.apple.com/article.html?artnum=108058 -
Can't connect imac to internet through Airport Express
Hello
I am trying to connect my new imac (2.4Ghz,OS X 10.5) to the internet through my Airport Express (v6.3) but have encountered some problems.
The set up goes like this:
Cable Internet <wired> TP-LINK Router <wired> AE <wireless> imac
The internet is coming from my landlord on the bottom floor of my apartment so I can't change the router.
The router is assigning a static IP to my AE (192.168.5.101).
I am using WEP 128 bit security.
I have set the AE through Airport Utility to act as a Bridge.
On the imac I set the Network preferences to manually select an IP address (192.168.5.110) which is out of the range of the Router (192.168.5.101-108).
The AE connects and lights up green and the imac recognises the AE but I still cannot access the internet...
I have also tried to wirelessly connect my PC laptop to the AE using other static addresses but I still can't connect to the internet.
Can anyone please help??
Regards
StarwolfgangHello Starwolfgang. Welcome to the Apple Discussions!
The router is assigning a static IP to my AE (192.168.5.101).
Are you sure that this provided IP address is static? If so, you also need to note the provided DNS server(s) IPs as well.
On the imac I set the Network preferences to manually select an IP address (192.168.5.110) which is out of the range of the Router (192.168.5.101-108).
Since you configured your AX in bridge mode, your computer will be dependent on the NAT (& possibly DHCP) services provided by your apartment's router. Assuming that your landlord doesn't filter out any IP addresses and that the IP address you set is valid, you need to compare your iMac AirPort's DNS server address settings with that provided by your apartment's router to be sure they match.
Finally, assuming that your apartment provides you with an Ethernet jack, if you connect your iMac directly (via Ethernet) can it access the Internet? -
Unable to connect to Internet via Airport Express - 'cannot contact server'
I'm unable to connect to the internet via my Airport Express. I'm using OS 10.3.9, and had the same setup with no problems at a previous address, but with a different modem from the same ISP.
My AE is connected - the light is green - and my mac is connected to the network in Internet Connect. But when I open Safari I get an 'unable to contact server' message.
I've tried rebooting everything (modem, AE, Mac), and leaving modem/AE off for several minutes. Also reset the AE, but to no avail.
The connection works fine via Ethernet cable.
Any ideas?Thanks, I checked out that advice doc (106798), but could not connect to the address (http://17.149.160.49) which is given to test if it's a DNS issue. My ISP says I shouldn't need DNS settings.
The service is PPPoE, and I went into Airport Admin Utility to check if the Airport was configured for this. Under Configure/Internet, I found it was set to 'Ethernet', so changed it to PPPoE. Then when I restarted I got connection status in the bar (and good Airport signal), but status flipped between 'looking for PPPoE host' and 'negotiating PPPoE host', sometimes sticking on one or the other each time I tried rebooting all gear.
Any other ideas? -
How to configure Solaris 10 on a dell laptop to connect to internet
Hi,
I am student and have installed Solaris 10 on my Dell laptop using SUN's Virtual box. I also have Opensolaris on my laptop that is able to connect to internet using any available wireless because of its auto settings. Can some one please guide me with the steps or tutorial to configure Solaris 10 to connect to internet either by LAN or wireless(preferable)
Some information about my Laptop:
Windows IP Configuration
Wireless LAN adapter Wireless Network Connection:
Connection-specific DNS Suffix . :
Link-local IPv6 Address . . . . . : fe80::548:a39d:e943:4144%12
IPv4 Address. . . . . . . . . . . : 192.168.100.198
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.100.1
Ethernet adapter Local Area Connection:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Ethernet adapter VirtualBox Host-Only Network:
Connection-specific DNS Suffix . :
Link-local IPv6 Address . . . . . : fe80::4112:b7fa:5de1:2f6e%15
IPv4 Address. . . . . . . . . . . : 192.168.56.1
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . :
Tunnel adapter Local Area Connection* 6:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 7:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 11:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 14:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
e1000g0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet 0.0.0.0 netmask ff000000
ether 8:0:27:60:84:8d
#netstat -nrv
IRE Table: IPv4
Destination Mask Gateway Device Mxfrg Rtt Ref Flg Out In/Fwd
224.0.0.0 240.0.0.0 127.0.0.1 lo0 8232* 0 1 U 0 0
127.0.0.1 255.255.255.255 127.0.0.1 lo0 8232* 0 33 UH 976 0
Please let me know if you need any other informationFor a start I would give my interface an inet number:
ifconfig <interface> inet <ip_address>
ifconfig e1000g0 inet 192.168.100.198
...further than that I would need to study.
Also see " How to configure internet Solaris 10" thread .
http://forums.sun.com/thread.jspa?threadID=5093731&tstart=0
Edited by: plasmichive on Nov 10, 2009 10:25 AM -
I want to connect Airport Express to my Internet in my dorm?
I just bought Airport Express and I am unable to get it to connect to the internet. I want to be able to just plug in an Ethernet cable into the Airport Express and have it work wirelessly with my computer. How do I do this?
ambisme, Welcome to the discussion area!
Does the IT support at your dorm/school allow you to connect your own wireless router?
If so, follow the steps you described. Connect an Ethernet cable from the wall to your AirPort Express (AX).
Maybe you are looking for
-
I have an airport express and want to know how to set up two different wireless networks. One with 5GHZ and one with 2.4GHZ so different devices can connect to either. I have an iphone 4 that will not connect to 5ghz. thank you!
-
My network connection is: HSDPA. I do not have a faster connection within 200km radius. Is there any way how I can download the iSO 6.1.3 to update my iPad?
-
How can I capture live HD video direct to hard drive?
Hello, My goal is to be able to capture 1080p video from a camcorder direct to the hard drive of a mac. Space is a concern, so ideally this would capture directly to a Mac Mini, but if the only option is to upgrade to a Mac Pro or MacBook Pro (for Th
-
A how-To guide about splitting import files exists?
Hi All, in his Webinar https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/409e4529-adbc-2a10-4d9b-e8fade570414 Klaus David said a "A how-To guide about splitting import files exists" (Page 20). Can anybody tell me where to find this
-
Hi! I have some problem and I need help.. fail-box problem with lokal and network system. I dont know how to solve it' Thank you...