Dell latitude unable to detect Airport Extreme base station

I have an Airport Extreme base station at my parents house and I am unable to detect the wireless network or connect to the base station on Dell Latitude D610 with Windows XP. I installed the base admin utility for windows Xp and it cannot detect the base station.
Please help....

You don't need the utility to connect, it is ONLY used to configure a base station.
Problems connecting an XP PC to an Airport Base Station
http://www.ifelix.co.uk/tech/2002.html
iFelix

Similar Messages

  • Airport Utility 5.4.2 was unable to find Airport Extreme base station.

    I downloaded the new Airport Utility 5.4.2 to my 2009 24" iMac with Snow Leopard. Now it is unable to find my Airport Extreme base station or Airport Express. My iMac is connected to the network via the Airport Extreme base station but the Airport Utility cannot find it. All I get is this message "Airport Utility was unable to find any Apply wireless devices. Make sure the Apple wireless device you want to set up is plugged in and in range of your computer and then click rescan to try again". I clicked rescan numerous time with no luck. I even downloaded the Airport Utility 5.4.2 again with no luck. What is wrong??? Everything was working fine until I downloaded the Airport Utility 5.4.2.

    Thanks for the info.
    Following your same steps exactly, I am able to save the configuration file to the desktop, or navigate to another folder to save it at that location.
    I was able to do this previously with 10.5.x and with current Snow Leopard. Notice that you list 10.4.x as your operating system. If you are still running this OS, it could be that 10.4.x does not allow this feature with 5.4.2?
    Not sure if downloading another copy of 5.4.2 would be worth the pain, as I'm inclined to believe that it probably would not help solve your issue. If you decide to do this, please post back with your results.

  • Powerbook cannot detect Airport Extreme base station

    I bought a new Airport extreme and cannot connect to it wirelessly. I called and tried to do everything to fix the problem but ended up having to have a replacement Airport sent to me. The new one arrives and same problem. I can see other wireless networks but cannot see the one from mine. When restarting the base station, I see my network for a second but it goes away and I can't connect to it. I'm thinking it might be my computer but I can see other networks... any suggestions on how to rectify the problem?

    Ok, thanks. I can only see, at this time, five choices:
    Try each step one-at-a-time, until successful. After each step, try accessing the AEBSn via Ethernet.
    o Shut down the AirPort Utility, and then, restart it.
    o Unplug the AEBSn, wait at least 5 minutes, and then plug it back in.
    o Reinstall the AirPort Utility on your PC to rule out any issues with the initial installation.
    o Install the AirPort Utility on another device (PC or Mac) to see if it can access the base station.
    o Perform a "hard" reset of the AEBS.

  • Connecting to hotspot from airport extreme base station

    I have a macbook and a Dell Inspiron connected to an airport extreme base station (with an antenna located on the mast) which is located on my sailboat. How do I set up the AEBS to connect to Wifi Hotspots so that I can access and print through the AEBS?
    Thanks for any help

    martinique, Welcome to the discussion area!
    It won't work. The AEBS will only join a wireless network if you use WDS and configure the AEBS as a remote or relay station. Unfortunately:
    only a very few (less than 7) 3rd party manufacturers support Apple's WDS
    to make WDS work, you need to configure the main base station (the one sending the signal) to allow the remote station to connect

  • Unable to access internet via my airport extreme base station

      I have an AirPort Extreme Base Station which is hard wired to a Mac and which communicates wirelessly to a Mac in another room.  My internet access is via comcast.  Direct connection from this computer to my modem works fine, but not if I go through the AirPort.  The LED lights of the AirPort indicate normal network activity, (flashing/on/flashing).  I have tried disconnecting and reconnecting everything and rebooting the computer.  The system has been working normally through the AirPort until today.

    I would recommend that you do the following as a minimum:
    Power-down the modem, AirPort base station, and computer(s).
    (OPTIONAL) Disconnect the AirPort base station from the Internet broadband modem.
    (OPTIONAL) While all of the devices are powered-down, perform a "factory default" reset on the base station. This will get it back to its "out-of-the-box" configuration and make setting it up much easier, especially if you use the "Assist me" process within the AirPort Utility. (ref: Resetting an AirPort Base Station or Time Capsule)
    (OPTIONAL) After the base station resets, go ahead and power it back down.
    (OPTIONAL) Reconnect the AirPort base station to the Internet broadband modem. For the Extreme and Time Capsule, be sure to connect the cable to the base station's WAN (circle-of-dots) port.
    Power-up the modem; wait at least 10-15 minutes to allow it adequate time to initialize.
    Power-up the AirPort base station; wait at least 5-10 minutes. Note: The AirPort's status light may continue to flash amber after it has intialized. That is because, there may be some additional configuration items necessary, like setting up wireless security, before the overall setup is completed to get a green status.
    Power-up your computer(s).
    In this basic configuration, the AirPort base station will broadcast an unsecured wireless network with a Network Name (SSID) of Apple Network NNNNNN. Network clients, connected to the base station either by wire or wireless, should now be able to access the Internet through the ISP's modem. Once Internet connectivity has been verified, you can use the AirPort Utility to configure the base station for wireless security and any other desired options. Please post back your results.

  • Airport extreme base station detecting someone elses network but not mine.

    Sorry if this subject has already been discussed but I couldn't see it anywhere.
    I have an airport extreme base station set up and it works fine but this morning i noticed that I had very little signal which has never happened before so upon further investigation I noticed that my computer was hooked up to a Netgear network amd not my own usual airport "home" network.
    I got my own network back again and my signal is now full strength. The worrying thing is that my computer couldn't seem to find my airport "home" network when I searched for it. I had to start again from scratch and reset it.
    Is there a way I can tell my computer to use only my airport network and no other? Someone obviously has an open network nearby.
    Message was edited by: lispiers

    Try the steps indicated in Mac OS X 10.4 Help: Choosing preferred AirPort networks.

  • MacBook in office unable to detect AirPort Extreme's signal?

    Hello all.
    I took my "old" AirPort Extreme Base Station (white UFO) to the office, connect it to a cable modem, wired network to my main G5 Tower (OS 10.4.11) and wireless network (closed) to my MacBook (OS 10.5.1).
    I reset the B.S. and went through the setup utility inside the MacBook. On first try, I was able to establish and connect the wireless signal to my MacBook, although strangely, certain websites were not accessible, simple website like http://www.leoparddocks.com/ was not accessible.
    This "intermittent" problem got worse a few days later where the MacBook totally cannot load any pages from Safari, although the AirPort Signal Strength on the Menu Bar is full (The B.S. is just beneath the desk)
    I can even access all of the B.S.'s settings and configurations through the MacBook, but just not able to load any pages in Safari.
    My original plan was to have the G5 Tower "enjoy" dual network of office intranet and also the internet via the wired network cable from the B.S. (Yes I know I will have to toggle between the 2 networks) and also wireless network access on my MacBook. But now seems like the plan is back to "square one", I have to plug the cable and hook it into the MacBook.
    If anyone knows how to solve this thing is greatly appreciated.
    Thanks and cheers

    I stopped by my local apple retail store and had a quick chat w/one of the lovely employees. He checked with a Genius and suggested I plug the ethernet cables into the appropriate ports and make sure both computers were set to use DHCP in network settings. The fact that I was running my iMac on Panther (not Tiger or Leopard) should not make a difference b/c the iMac was hardwired via ethernet to the airport and had current airport software.
    It took a little tweaking on my part at home, but using that advice I literally had both computers on the internet in less than 20 minutes. Those guys really are geniuses!
    Thanks!

  • Airport Utility cant connect to Airport Extreme Base Station, Error code -4

    I am unable to use my Apple-product. Earlier it worked, with these settings: The Airport Extreme Base Station worked as a Gigabit switch and an Access Point. It was not supposed to work as a router, since I have a server "on the far side" of the AEBS.
    In any case, it worked for a while. Then it started to act strangely, so I tried to check its settings. I was unable, so I did a factory reset. And haven´t been able to connect (for configuring) since. (It still works as a router and access point, but with the default settings, and with a blinking yellow led.)
    When I use the Airport Utility (5.5.1) connected with a cable it finds nothing. Should I be able to configure it wired? When I connect wireless to the default "Apple Network XXXXXX" it finds the Airport Extreme "with default settings". I click "continue" or "Manual setting", and it says "Detecting wireless Apple Devices" (bear in mind that I translate the messages from swedish, It might get wrong), and then after a minute:
    An error occurred while trying to access the base station. Make sure your network connection is valid and try again. Error Code: -4
    I have shut off the firewall in both Windows and Panda Cloud Office Protection. I have tried to make lots of factory resets.

    See this article for instructions on how to install AirPort Utility 5.6 for Lion on Mountain Lion:
    http://www.macworld.com/article/1167965/mountain_lion_and_the_ancient_airport_ba se_station.html

  • Configure TC and Airport Extreme Base Stations with different channels

    I had to do some serious workarounds to use the Airport Extreme Base Stations as an access point with the same wireless network name primarily due to channel overlap.  I thought I would post my results here since I didnt' find a good article online.
    Also, I found the Snow Leopard verison (5.4.2) of the Airport Setup Utility far superior to Lion's Airport Utility (6.x) in terms of advanced setup. 
    Setup is a 3 flloor house where the 3 wired network locations have wireless overlap.  The problem was that the access points would not hand off the wireless signal because the channels for each airport/TC were automatically set to the same channel.  In non-apple setups, this is how you force a wireless client to switch access points (since the wireless software on your client/mac/windows can detect which access point is stronger and moves to the alternate channel.
    Using apple's "Extend this wireless network" option removes any ability to manually configure wireless channels.  I am writing this from memory, so feel free to ask questions and I will track this topic:
    Procedure
    Setup time capsule as your base station.  Do all the setup for your wireless and guest networks.  Manually configure the network and change the wireless channel to a specific channel for a/b/g networks (e.g., 3) and n networks (e.g, 167).
    Plug your first airport extreme/access point into your wired network.  Do not plug it into the "internet" ethernet plug, use one of the 3 ethernet switch locations
    Use the airport utility to first configure it to "extend" your wired network. 
    Then, go in and reconfigure it manually in the airport utility.  Choose the option to setup a "new network" and name the network the same as the TC wireless network name, security, etc.
    Change the channel from "auto" to a different channel than the TC (e.g., 6 and 137). 
    Now go to the top tab and click on the "internet" icon
    Go to the DHCP tab and change it to "bridge mode."  This will tell the AE to not give out IP addresses (the TC will do this for you).  If you get an error that the IP ranges conflict, you have not done this
    Note that if you have a guest network setup, you will need to set this up on the AE as well. 
    Now test your airport setup.  Take your client (macbook, iOS device) and connect to your network.  Move to a spot near the TC and pull up a web page.  Keep an eye on the signal strength and beginv moving toward the AE.  Refresh the page as you move around.  You should at some point see the signal strength increase.  Refresh your page again.  You should be now connected to to the AE.  I have found that Macbooks do a better job than iOS devices because you get an extra signal bar to measure strength, and they have larger antennas which allows you to better measure problems with handoff
    Another test you can do is to start backing up on your TC and then test the move.  The handoff will truly show you that the TC is handling the process but the AE is relaying to the TC for backup.
    If you need to setup another AE, simply follow setups 3-10.
    I hope this helps others.  I've done this setup 100 times on Linksys devices and although they are cumbersome, they at least allow me to do this setup much more quickly and easily than the apple products. 

    I had to do some serious workarounds to use the Airport Extreme Base Stations as an access point with the same wireless network name primarily due to channel overlap.  I thought I would post my results here since I didnt' find a good article online.
    Also, I found the Snow Leopard verison (5.4.2) of the Airport Setup Utility far superior to Lion's Airport Utility (6.x) in terms of advanced setup. 
    Setup is a 3 flloor house where the 3 wired network locations have wireless overlap.  The problem was that the access points would not hand off the wireless signal because the channels for each airport/TC were automatically set to the same channel.  In non-apple setups, this is how you force a wireless client to switch access points (since the wireless software on your client/mac/windows can detect which access point is stronger and moves to the alternate channel.
    Using apple's "Extend this wireless network" option removes any ability to manually configure wireless channels.  I am writing this from memory, so feel free to ask questions and I will track this topic:
    Procedure
    Setup time capsule as your base station.  Do all the setup for your wireless and guest networks.  Manually configure the network and change the wireless channel to a specific channel for a/b/g networks (e.g., 3) and n networks (e.g, 167).
    Plug your first airport extreme/access point into your wired network.  Do not plug it into the "internet" ethernet plug, use one of the 3 ethernet switch locations
    Use the airport utility to first configure it to "extend" your wired network. 
    Then, go in and reconfigure it manually in the airport utility.  Choose the option to setup a "new network" and name the network the same as the TC wireless network name, security, etc.
    Change the channel from "auto" to a different channel than the TC (e.g., 6 and 137). 
    Now go to the top tab and click on the "internet" icon
    Go to the DHCP tab and change it to "bridge mode."  This will tell the AE to not give out IP addresses (the TC will do this for you).  If you get an error that the IP ranges conflict, you have not done this
    Note that if you have a guest network setup, you will need to set this up on the AE as well. 
    Now test your airport setup.  Take your client (macbook, iOS device) and connect to your network.  Move to a spot near the TC and pull up a web page.  Keep an eye on the signal strength and beginv moving toward the AE.  Refresh the page as you move around.  You should at some point see the signal strength increase.  Refresh your page again.  You should be now connected to to the AE.  I have found that Macbooks do a better job than iOS devices because you get an extra signal bar to measure strength, and they have larger antennas which allows you to better measure problems with handoff
    Another test you can do is to start backing up on your TC and then test the move.  The handoff will truly show you that the TC is handling the process but the AE is relaying to the TC for backup.
    If you need to setup another AE, simply follow setups 3-10.
    I hope this helps others.  I've done this setup 100 times on Linksys devices and although they are cumbersome, they at least allow me to do this setup much more quickly and easily than the apple products. 

  • Problem consistently printing via new (summer 2011) AIRPORT EXTREME BASE STATION and Brother wireless printer (model HL5370DW). What am I doing wrong?

    Thanks in advance for any help you folks can offer. I'm a newb here and will try to offer as much detail as I can about the dilemma at hand.
    Scenario: Home network has been recently set up for wireless internet access via NEW Airport Extreme Base Station (purchased September 2011). Units accessing the network include: 2011 Macbook Pro, 2011 Macbook Air, 2007 Macbook, 2009 Macbook Pro, 2 iPhone 3GSs, and a 1st-gen iPad (and a partridge in a pear tree AEBS is configured to run WPA2 encrypted network, as well as a WPA2 guest network. I am attempting to yoke a BROTHER HL5370DW wireless B or G/ ethernet / usb-capable printer to the main network such that any and all units can print wirelessly or its equivalent (i.e., via printer hooked to AEBS through USB hub)
    Problem: Despite configuring the Brother printer to recognize the main WPA2 network I created, I am unable to get wireless printing to work. My workaround was to physically connect Brother printer to AEBS via USB, specifically using a Belkin USB hub (after all, I wanted access to usb drives, as well as the printer). This workaround works ONLY SOME OF THE TIME. Generally, after a fresh boot of any computer or after a restart of the AEBS, any given computer will be able to print (i.e., any computer wirelessly connected to the main WPA2 network recognizes the printer). HOWEVER, at random times, printer access is gone (as is access to USB drives connected to AEBS's usb hub). Wireless networks are still up and running when that happens. IS THERE A WAY TO GET THE USB HUB's devices (i.e., printer and usb drives) to ALWAYS REMAIN AVAILABLE AS LONG AS THEY STAY CONNECTED TO THE AEBS? In other words, what accounts for the intermittent loss of the usb peripherals?
    Sometimes, I just shut the airport off on whatever computer is having this problem, and the problem goes away. Sometimes, the problem is present across all computers in the house, sometimes only a few are affected. I can ALWAYS see the AEBS in the Airport Utility if the AEBS is connected to the particular computer via ETHERNET CABLE.
    My theories:
    - true wireless printing (i.e., without usb hub workaround) doesn't work because the N network somehow isn't backwards compatible with the Brother printer, which, i believe, is B/G. Although...isn't Wireless N networking supposed to work with BG devices? I did find a thread (https://discussions.apple.com/thread/2570774?start=0&tstart=0 ) that explains some of the particulars of WPA2 encryption and Wireless B/G issues, but it was beyond my level of comprehension (I'm a psychologist, but not an Apple Genius
    - The usb workaround is only intermittently viable because of some flaw in the Airport or Airport Utility that causes dropouts to happen when a Macbook Pro or Air's lid gets closed or one gets opened after having been at a different network (e.g., at my office).
    QUESTIONS:
    - Should I try to use my old router (7 year old Linksys WRT54G) as an access point and connect the Brother printer to that G-router? How do I do that?
    - I wouldn't mind just relying on the usb hub method if I could just insure more consistency (i.e., no random dropouts of peripherals). How could I do this?
    Rule out:
    - wireless printing works on my printer - it was being recognized back before the AEBS. I had the Linksys router running a WEP network and had the wireless printer talking with no cables to the router and the computers. (I just don't want to revert to using WEP encryption given its lack of security and my trying to protect HiPAA related health information on behalf of patients)
    Any help will be greatly appreciated.
    Thanks in advance!

    13 ASCII characters = 104 (aka 128)-bit WEP
    encryption
    If turning off WEP works, then you just need to
    provide the cameras with the "Equivalent Network Password".
    One of the problems with WEP is that the actual
    standard relies on a 10 character HEX key for 40bit
    WEP and a 26 character HEX key for 128bit WEP.
    In order to make things easier, vendors use certain
    algorithms to convert simple alphanumeric passwords
    (or passphrases) into HEX keys, thus enabling the use
    of simple easy to remember WEP password rather than
    lengthy HEX keys. The problem is that different
    vendors use different algorithms to generate the HEX
    key and therefore a ASCII password on an AEBS will be
    hashed differently on a non-Apple client and vice
    versa.
    You may find the following article helpful:
    - Apple article, especially the part about
    "Third-party client to Airport".
    Brilliant idea about trying the system with No encryption on... that DID solve the problem... almost.. once I turned off the encryption option, and restarted the Airport, I got a dialog box showing that the "Base station needs attention" but it didn't indicate WHAT kind of "assistance" it needed. Nonetheless, I closed out of the Airport program only to find that the indicator light, which had been Green, was now, flashing Yellow and I could not connect anything, including my computer. I opened the Airport program again and found the ONLY way I could get the Green light on was to select some sort of encryption option... then the light would go Green again but my cameras would not hook up again, and when I went back in and ONLY changed the option to NO encryption, I got the yellow flashing light and the "this base unit needs attention" warning...
    I think your suggestions are almost on the mark... is there any way of reconciling the WEP coding between the cameras and the Airport??? Or turning off the encryption option and STILL have Airport work?
    Thanks again for your help and suggestions... I really appreciate it.
    geoff

  • Multipmultiple Airport Extreme Base Stations: WDS Or "Extend Wireless Network" To Have Wired -- Wireless Bridge?

    Hello there!
    I've been looking for this info, but have as yet been unable to find it. Here's my scenario:
    I have two Airport Extreme Base Stations (both are dual band) and 3 airport expresses. The main internet connection in my house is in one room, where I have an AEBS as the main wireless router. In another room, I have a bunch of ethernet-only devices. I'd like to use the 2nd AEBS in this room, plug the ethernet devices into it and have the 2nd AEBS act as a wired <--> wireless bridge (connected to the same wireless network as the 1st AEBS). I've attempted this via "extend a wireless network," but the ethernet devices don't get past the AEBS they're plugged into. Should I instead be implementing WDS?
    I mention the airport expresses as I'd like to have airtunes & wireless signal in other areas, but would like to keep the set-up as simple as possible (i.e., not config the AXes for WDS unless it's required).
    Thanks in advance for any help!

    Unlike the 802.11n AirPort Express Base Station (AXn), the 802.11n AirPort Extreme Base Station (AEBSn) cannot be configured as a wireless Ethernet bridge.
    However, there are at least two ways to configure it to provide wired clients access:
    Connect the second AEBSn back to the first by Ethernet; reconfigure the second AEBSn as a bridge and disable its wireless radios, or
    Reconfigure both AEBSns into an extended wireless network. For 802.11n AirPorts, this would be called a dynamic WDS. The AEBSn, connected to the Internet would be the "main" base station and it would only require that you enable the "Allow this network to be extended" option in the AirPort Utility. The extending AEBSn would need to be configured with the option, Wireless Mode = Extend a wireless network, enabled.
    In both configurations, the second AEBSn's Ethernet ports would be enabled for wired clients.

  • HT1218 After a recent iTunes update attempt iTunes no longer functions and the airport extreme base station is not accessable on our computer.  We still have wifi but cannot access the base station software.

    After a recent iTunes update attempt iTunes no longer functions and the airport extreme base station is not accessable on our computer.  We still have wifi but cannot access the base station software.

    Thanks for the reply. I appreciate the response. I tried that approach this evening and it didn't work for me. (Technically it worked for me, when I was hardwired into my base station, but would not work for me wirelessly, which is my main issue.)
    Again, using the approach you recommended works only if I have my ethernet cable attached to the LAN port so my computer is communicating directly to the base station through the hard wire. I am able to scan for my base station and make setting adjustments normally this way too.
    As soon as I disconnect from the LAN port and try to go wireless is where I run into problems. The Base Station's wireless network I created is available to choose in the top right corner of the monitor with all of the other available wireless devices/networks -- but the network I created does not have access to the internet. I am also unable to configure my Base Station wirelessly. When my Airport Utility tries to scan for the Base Station and Network, it cannot find any Apple Wireless Device. It's like the Wireless Network in my base station is not sending out a signal.
    Is there a way to resolve this issue?

  • Airport Extreme base station no longer playing nice with Mac Pro

    This is a strange problem...
    I have an Airport Extreme base station (purchased in 2004) that I use with verizon DSL to get a wireless network going in my house, and I connect three computers wirelessly.
    I have an ipod touch and toshiba PC laptop that are both able to connect to the network and run just fine. But lately (past 2 weeks or so) when I try to connect with my MacPro desktop I can go to a few sites, but after a few minutes the airport locks up. At that point none of my computers will connect and I have to unplug and then replug the airport. At that point the network will start up again and if I do not try to get on with Mac Pro then things run fine, but when I try to connect with desktop again, after another few minutes the same thing happens.
    I know the problem is with the airport and my Mac Pro - I have done numerous connection experiments and have narrowed the problem down to that.
    Is it possible that my MacPro might be drawing more power and causing the airport to overheat? (it is rather hot in the room with DSL connection)
    Or should I accept that the current base it old, and bite the bullet and get a new base?
    Any thoughts?

    Could you post what you did in order to resolve the issue. I'm having a problem with the base station in that I cannot connect to the internet with my laptops (a mac and pc) while I can connect wirelessly to my network with my desktop (G4). The base station is not detected in the base statin admin utility or the aiport setup utility. If anyone else has a solution I would be much obliged to read it.
    Thanks!

  • How do I view a file from a usb hard drive connected to my airport extreme base station on my ipad 2?

    Hi,
    I just purchased the airport extreme base station.  I have a usb hard drive connected to the base station.  Is it possible to view this hard drive on my ipad 2?  I have been unable to do it.  Any help would be appreciated.

    You can't, not natively. An app like FileBrowser:
    http://www.stratospherix.com/products/filebrowser/
    may make this possible, though.
    Regards.

  • Why does the new Dual-Band AirPort Extreme Base Station act as a proxy?

    The previous thread
    http://discussions.apple.com/thread.jspa?threadID=1531675
    has been archived and nothing came of it, but after testing, I'm certain that their findings are true.
    The Dual-Band AirPort Extreme Base Station (AEBS) with firmware 7.4.1 acts as a proxy for TCP ports 21, 554, and 7070 when NAT is turned on. This can be verified by using Nmap on any external server known to NOT have the ports open and having Nmap return that the ports are open. You can telnet to these ports to verify that they're "open," even though they are not on the server.
    This functionality appears to be undocumented and as far as I can tell, the only way to turn it off is to put the AEBS into bridge mode and having some other device do NAT further upstream.
    As a computer professional, this functionality extremely undesirable, particularly since it is not documented and doesn't have an "off switch." I wasted a bunch of time with one of my network engineers because of this, thinking that some network router was spoofing our server. I also wasted a bunch of my time trying to detect whatever "stealthy rootkit" had opened a FTP server and some other botnet related ports on our server, when in reality, it was simply my AEBS tricking me.
    Disabling NAT-PMP ("Enable NAT port mapping protocol") does not affect this.
    Is it too much to ask to have a checkbox in the "Advanced" section of the AirPort Utility to turn this feature off?

    Welcome to the discussions forum Michael Bennett2.
    Thanks for investigating this odd behavior.
    If you want your work to be noticed by those who can effect change, you'll have to tell Apple via their feedback link. It won't do any good to post it here.
    http://www.apple.com/feedback/

Maybe you are looking for