Dell OpenManage agent installation

I am just starting evaluation of Oracle VM and need to install the Dell OpenManage agent on the host. What Linux distro is Oracle VM based on so I can get the correct agent? Thanks for your help.

user12094601 wrote:
I am just starting evaluation of Oracle VM and need to install the Dell OpenManage agent on the host. What Linux distro is Oracle VM based on so I can get the correct agent? Thanks for your help.Oracle VM 2.1.2 and 2.1.5 are based on EL5 GA
Oracle VM 2.2 is based on EL5 Update 3
Hope that helps.

Similar Messages

Unable To Install Dell OpenManage On ESXi 4.0 Host

I have been having issue installing dell OpenManage on a PowerEdge 2950 ESXi 4.0 host. Some details about the host include: VMware ESXi 4.0.0 Update 2 build-332073. First I would like to know if anyone has been successful doing this and what are the steps? I also think I am confused on where the actual download is for OMA for this particular ESXi version.I did try installing a few version but I ended up getting a few different errors, some that I can remember include:
"please wait patch installation is in progress ... there was an error setting up esxi installation destinationbootbank preparation failed: /sbin/bootbankstage-install.sh -v prep returned (1)"
Error (28) on file : [Errno 28] No space left on device"
Some things I tried:
Make sure CIMOEMProvidersEnabled is set to 1
tried downloading different versions from Dell. (see below links)
tried installing from the remote CLI using vihostupdate.pl --server <esxhost> --username root -i -b c:\oem-dell-openmanage-esxi_6.1-0000.zip
tried installing from SSH using the esxupdate --bundle OM-SrvAdmin-Dell-Web-6.3.0-2075.VIB-ESX41i_A00.8.zip update
Any help would be appreciated. Thanks in advanced, I am pulling my hair out here on this one.
www.dell.com/.../DriversDetails
How to Install OpenManage Server Administrator (OMSA) 6.1 on ESXi 4 | Dell US

Ice2921,
Here is a walkthrough I put together on using OMSA with ESXi. Verify the steps you have done, compared to the steps here.
Download the Dell OpenManage Offline Bundle and VIB for ESXi 4
http://dell.to/1bD7UJm
Log onto a Windows machine on the same network.
Type in the IP of the ESXi server in a Internet Explorer window.
Download the VI Remote CLI tool, or Vsphere. Those tools can be downloaded right there from the webpage that comes up.
Installing the offline VIB bundle
Copy the OMSA 6.5 VIB to the ESXi host (/var/log/vmware or /vmfs/volumes/<datastore>)
Run the following command from the vSphere CLI prompt:
esxcli.exe --server <server> software vib install –d <remote path to VIB>
Example: C:\Program Files\VMware\VMware vSphere CLI\bin>esxcli.exe --server 10.180.57.109 software vib install -d /var/log/vmwar/Dell_OpenManage_ESXi_OM650-offline_bundle-467660.zip
Enter username: root
Enter password:
Installation Result
Message: The update completed successfully, but the system needs to be rebooted for the changes to be effective.
Reboot Required: true
VIBs Installed: Dell_bootbank_OpenManage_6.5-0000
VIBs Removed:
VIBs Skipped:
Reboot, Check Software > Advanced Settings for UserVars.CIMvmw_OpenManageProviderEnabled should already be set to 1
Verify OMSA VIB on ESXi 5
esxcli.exe --server <server> software vib list
Example:
C:\Program Files\VMware\VMware vSphere CLI\bin>esxcli.exe --server 10.180.57.109 software vib list
Enter username: root
Enter password:
Name Version Vendor Acceptance Level Install Date
Dell-Configuration-VIB 5.0-0 Dell PartnerSupported 2011-10-05
Dell-License-VIB 5.0-0 Dell PartnerSupported 2011-10-05
OpenManage 6.5-0000 Dell VMwareAccepted 2011-10-05
That installs the server side of it.
This is for the workstation -
Download OpenManage Server Administrator Managed Node version 6.5 from Dell’s support site (not the OpenManage Server Administrator Web Services under the ESXi downloads)
ftp.us.dell.com/.../OM-SrvAdmin-Dell-Web-WIN-6.5.0-2247_A01.10.exe
On a separate windows machine install OpenManage Server Administrator Managed Node and choose ‘Custom’ install.
When choosing features make sure Server Administrator Web Server is selected (If installing on a desktop it could be the only option).
Once the install is complete, double-click on the server administrator icon.
On the login page Enter the ESXi server ip address, use root for the user, and the root password. Make sure to check the option to ignore certificate warnings.
Done! You should be able to access the OpenManage Managed Node Web Interface.
Let me know how it goes.

Mapping del credere agent and consignment stockist in sap sd

Dear Gurus
My client has trading business with IOCL company acted as a del credere agent and consignment stockist. Generally, IOCL sending the material our company go down. we do the business with the customers and we are paying the amount to the IOCL in advance and we are taking the money from the customer. For doing this business we are getting from the IOCL. we are also maintaining RG23D register. Our go downs are registered as depot. But we are not selling the material directly, please tell me how can we map this scenario.
Regards
thirupathi

hi,
Sales office is termed as an internal organisation element in SAP. ie:- Its a representation of the company at a specified geography.
The distributor is always a customer for the business. The operations of the distributor are completely different from the company. Hence, mapping distributor as a sales office is completely ruled out.
The distributors can be taken as a DISTRIBUTION CHANNEL in the org structure.
All the distributors are created as customers in a specific sales area.
Secondary sales is a business activity happening from the distributor to the dealer.
So, in any business automation(not only SAP) we need not automate this activity.
This would be automated by the distributors. We can only frame business regulations in domain for the secondary sales but not automate it.
Reward if helpful.
regards,
sriram

FAM 8.0, Tomcat J2EE agent installation problem

Hello:
I was able to install FAM 8.0 in Tomcat 6.0.14 on Ubuntu (7.04) Linux. Everything seems fine. In the end, the applications I want to use with OpenSSO also make use of Tomcat 6.0.14. I noticed on the opensso users email list that the Tomcat 3.0 agent won't be available until early next year; but that the 2.2 agents should work with FAM 8.0. So, I got the the J2EE agent for Tomcat - SJS_Tomcat_Server_55_agent_2.2-01.tar.gz. The documentation makes no references to Tomcat 6, and I'm hoping this is due to the fact that Tomcat 6 was not available when the documentation was written.
Does this agent work with Tomcat 6? I have this problem when installing the agent (agentadmin --install):
$CATALINA_HOME environment variable is the root of the tomcat
installation.
[ ? : Help, < : Back, ! : Exit ]
Enter the $CATALINA_HOME environment variable: /Users/jas/Development/opensso/tryout/apache-tomcat-6.0.14
Invalid directory specified for the $CATALINA_HOME environment variable
Invalid CATALINA_HOME directory :
/Users/jas/Development/opensso/tryout/apache-tomcat-6.0.14I can see in debug/agentadmin.log the following:
[05/24/2008 13:06:37:684 PDT] FileSystemValidator : Is directory : /Users/jas/Development/opensso/tryout/apache-tomcat-6.0.14 valid ? true
[05/24/2008 13:06:37:686 PDT] HomeDirValidator : Is $CATALINA_HOME directory /Users/jas/Development/opensso/tryout/apache-tomcat-6.0.14 valid ? false
[05/24/2008 13:06:37:686 PDT] Invalid CATALINA_HOME directory : /Users/jas/Development/opensso/tryout/apache-tomcat-6.0.14This directory does indeed exist, and is accessible by the user I'm logged in as. It appears FileSystemValidator agrees with me, but HomeDirValidator has a problem. I tried this on both Ubuntu 6.04 and Mac OS X 10.5.2. Does this indicate that Tomcat 6 is not supported? Or is it indicative that neither OS on which I've tried to install the agent is officially supported?
Thanks!
Jeff

Hi Denis:
Before being redirected to another short term task, I did indeed get the Tomcat 6 agent to work. I probably won't be able to look at OpenSSO again seriously for another couple of months. :(
I have the OpenSSO server running on Tomcat 6.0.14 on Ubuntu 6.x Linux running in a virtual machine on my Mac. I was not able to get the server to run directly on the Mac, and I cannot remember the reason at this time.
But, as far as the agent goes, I run it again using Tomcat 6.0.14 on my Mac (Mac OS X 10.5.2), using the 1.5 JRE. I do have the agentapp war deployed as well as the agentsample web application to play with. In my catalina.out file:
Jun 18, 2008 10:07:20 AM org.apache.catalina.core.StandardEngine start
INFO: Starting Servlet Engine: Apache Tomcat/6.0.14
Jun 18, 2008 10:07:20 AM org.apache.catalina.startup.HostConfig deployWAR
INFO: Deploying web application archive agentapp.war
Jun 18, 2008 10:07:21 AM org.apache.catalina.startup.HostConfig deployWAR
INFO: Deploying web application archive agentsample.war
Jun 18, 2008 10:07:22 AM org.apache.coyote.http11.Http11Protocol start
INFO: Starting Coyote HTTP/1.1 on http-8090
Jun 18, 2008 10:07:22 AM org.apache.jk.common.ChannelSocket init
INFO: JK: ajp13 listening on /0.0.0.0:8011
Jun 18, 2008 10:07:22 AM org.apache.jk.server.JkMain start
INFO: Jk running ID=0 time=0/16 config=nullI have no error messages is any Tomcat log file.
I checked out the source code for the Tomcat v6 agent (2.2) on May 27, so I don't know how that compares to yours or what's been checked into CVS since my build. I also don't know what the OpenSSO NamingService is.
I assume you used fully qualified domain names to specify the web application to be protected by agent as well as the OpenSSO server itself. The following is the output of the conversation when I run the agent installer script on my system. It has been redacted a bit (domain name and encryption key) to protect my client, but otherwise this is what I supplied to the installer:
Enter the complete path to the directory which is used by Tomcat Server to
store its configuration Files. This directory uniquely identifies the
Tomcat Server instance that is secured by this Agent.
[ ? : Help, ! : Exit ]
Enter the Tomcat Server Config Directory Path
[/opt/apache-tomcat-6.0.14/conf]: /Users/jas/Development/opensso/tryout/apache-tomcat-6.0.14/conf
Enter the fully qualified host name of the server where Access Manager
Services are installed.
[ ? : Help, < : Back, ! : Exit ]
Access Manager Services Host: login.opensso.example.com
Enter the port number of the Server that runs Access Manager Services.
[ ? : Help, < : Back, ! : Exit ]
Access Manager Services port [80]: 8080
Enter http/https to specify the protocol used by the Server that runs Access
Manager services.
[ ? : Help, < : Back, ! : Exit ]
Access Manager Services Protocol [http]:
Enter the Deployment URI for Access Manager Services.
[ ? : Help, < : Back, ! : Exit ]
Access Manager Services Deployment URI [/amserver]: /opensso
Enter the fully qualified host name on which the Application Server
protected by the agent is installed.
[ ? : Help, < : Back, ! : Exit ]
Enter the Agent Host name: analysis.opensso.example.com
$CATALINA_HOME environment variable is the root of the tomcat
installation.
[ ? : Help, < : Back, ! : Exit ]
Enter the $CATALINA_HOME environment variable: /Users/jas/Development/opensso/tryout/apache-tomcat-6.0.14
Choose yes to deploy the policy agent in the global web.xml file.
[ ? : Help, < : Back, ! : Exit ]
Install agent filter in global web.xml ? [true]:
Enter the preferred port number on which the application server provides its
services.
[ ? : Help, < : Back, ! : Exit ]
Enter the port number for Application Server instance [80]: 8090
Select http or https to specify the protocol used by the Application server
instance that will be protected by Access Manager Policy Agent.
[ ? : Help, < : Back, ! : Exit ]
Enter the Preferred Protocol for Application Server instance [http]:
Enter the deployment URI for the Agent Application. This Application is used
by the agent for internal housekeeping.
[ ? : Help, < : Back, ! : Exit ]
Enter the Deployment URI for the Agent Application [/agentapp]:
Enter a valid Encryption Key.
[ ? : Help, < : Back, ! : Exit ]
Enter the Encryption Key [XXmyencryptionkeyXX]:
Enter a valid Agent profile name. Before proceeding with the agent
installation, please ensure that a valid Agent profile exists in Access
Manager.
[ ? : Help, < : Back, ! : Exit ]
Enter the Agent Profile name: testagent1
Enter the path to a file that contains the password to be used for identifying
the Agent.
[ ? : Help, < : Back, ! : Exit ]
Enter the path to the password file: /Users/jas/Development/opensso/tryout/agent_password
SUMMARY OF YOUR RESPONSES
Tomcat Server Config Directory :
/Users/jas/Development/opensso/tryout/apache-tomcat-6.0.14/conf
Access Manager Services Host : login.opensso.example.com
Access Manager Services Port : 8080
Access Manager Services Protocol : http
Access Manager Services Deployment URI : /opensso
Agent Host name : analysis.opensso.example.com
$CATALINA_HOME environment variable :
/Users/jas/Development/opensso/tryout/apache-tomcat-6.0.14
Tomcat global web.xml filter install : true
Application Server Instance Port number : 8090
Protocol for Application Server instance : http
Deployment URI for the Agent Application : /agentapp
Encryption Key : XXmyencryptionkeyXX
Agent Profile name : testagent1
Agent Profile Password file name :
/Users/jas/Development/opensso/tryout/agent_password
Verify your settings above and decide from the choices below.
1. Continue with Installation
2. Back to the last interaction
3. Start Over
4. Exit
Please make your selection [1]: 1
Updating the
/Users/jas/Development/opensso/tryout/apache-tomcat-6.0.14/bin/setclasspath.sh
script with the Agent classpath ...DONE.
Creating directory layout and configuring Agent file for Agent_001
instance ...DONE.
Reading data from file
/Users/jas/Development/opensso/tryout/agent_password and encrypting
it ...DONE.
Generating audit log file name ...DONE.
Creating tag swapped AMAgent.properties file for instance Agent_001 ...DONE.
Creating a backup for file
/Users/jas/Development/opensso/tryout/apache-tomcat-6.0.14/conf/server.xml
...DONE.
Creating a backup for file
/Users/jas/Development/opensso/tryout/apache-tomcat-6.0.14/conf/web.xml
...DONE.
Adding SJS Tomcat Agent Realm to Server XML file :
/Users/jas/Development/opensso/tryout/apache-tomcat-6.0.14/conf/server.xml
...DONE.
Adding filter to Global deployment descriptor file :
/Users/jas/Development/opensso/tryout/apache-tomcat-6.0.14/conf/web.xml
...DONE.
Adding SJS Tomcat Agent Filter and Form login authentication to selected Web
applications ...DONE.
SUMMARY OF AGENT INSTALLATION
Agent instance name: Agent_001
Agent Configuration file location:
/Users/jas/Development/opensso/tryout/tomcat_v6_agent/Agent_001/config/AMAgent.properties
Agent Audit directory location:
/Users/jas/Development/opensso/tryout/tomcat_v6_agent/Agent_001/logs/audit
Agent Debug directory location:
/Users/jas/Development/opensso/tryout/tomcat_v6_agent/Agent_001/logs/debug
Install log file location:
/Users/jas/Development/opensso/tryout/tomcat_v6_agent/logs/audit/install.log
Thank you for using Access Manager Policy Agent
[jaslap:tryout/tomcat_v6_agent/bin] jas% Can you post the exception details you're getting. That might help someone diagnose the problem.
Take it easy,
Jeff

ZLM Agent IR2 agent installation fails

Hi all
I have installed ZLM 7.3 IR2 Server in SLES 10 SP2. The ZLM Server setup is not able to complete on sles11 server, the system hangs. Also when trying to install the ZLM 7.3 IR2 agent on SLED 11 OS, the installation starts & hangs in the middle.
Some of the error messages are
1)Error no 111 Connection Refused
2) when executed the zlm-config file it displays the "OS is not supported version"
The SuSEfirewall is set to stop & iptables rules were not set.
I have tried the ZLM 7.3 IR2 agent installation in a freshly installed SLED 10 machine, but the machine is not able to contact the server (host name not found). I have not configured DNS service in the server machine. Please provide suggestions in the ZLM 7.3 IR2 agent installation.

baranii,
a few questions for my understanding:
I have installed ZLM 7.3 IR2 Server in SLES 10 SP2.
This is a running ZLM server and you try to register the other devices to this server. Correct ?
The ZLM Server setup is not able to complete on sles11 server, the system hangs.
SLES 11 or SLES 11 SP1 ? For SLES 11 SP1 you would need to use ZLM 7.3 IR3.
Do you want to install another ZLM server on this SLES 11 server or just the agent ?
I have tried the ZLM 7.3 IR2 agent installation in a freshly installed SLED 10 machine, but the machine is not able to contact the server (host name not found). I have not configured DNS service in the server machine.
The agent must be able to resolve the dns name of the zlm server.
You can either configure DNS or you can add an entry to the /etc/hosts file of the managed device. But you must make sure the device can afterwards ping the ZLM server by its name. (ping <ZLM Server Name>).
It is possible to register the zlm server by its ip address and not by it's name, but5 I would recommend to use the dns name.
So if you have fixed the name resolution and retry the agent installation, verify the zlm-install.log file if a installation fails. That log file is available in /var/opt/novell/logs/zenworks. Go from the end back and look for errors or warnings.
Rainer

Need Agent Installer for Solaris (SPARC)

Hi All,
I have downloaded Grid Control Agent Installer for Solaris from http://www.oracle.com/technology/software/products/oem/htdocs/agentsoft.html.
When I tried to extract the zip file, I am getting the following error message.
"Can not open file. It does not appear to be a valid archive. If you downloaded this file, try downloading the file again."
Even I tried using http://sac.us.oracle.com/download/index.html also but getting the same error.
Please send me the location if you have,
Thanks
Sumathi

Most commands are identical. Performance analysis, loading all are similar. Tape interaction, creation of tape devices is going to be pretty much the same.
The differences show up a lot at the hardware level. HBAs aren't usually the same, many drivers (and their quirks) are different between the architectures. If you're debugging connectivity to a tape library, those differences may be critical.
So you can't get as close as you may want, but I'll bet it would still be helpful.
Darren

MBSA Windows Update Agent installation

I'm implementing MBSA on our domain. I've worked through the various firewall issues, etc. Next I received a Security Update Scan Result that "Computer has an older version of the client and security database demands a newer
version. Current version is and minmum required version is ." This is pasted directly from the screen. It appears information is missing from the message.
Based on research of the message, I reran the scan with the "Configure computers for Microsoft Update and scanning prerequisites" option selected. Then I get the result "Windows Update Agent installation succeeded.Restart
the target computer to have Windows Update Agent updated completely." Scanning the computer after a restart just repeats the same results. Looking in the WindowsUpdate.log on the target computer, there are messages stating that 3
CBS packages were evaluated and that each is not applicable. "WUESTUP has finished. Exit code is 0. Reboot is NOT needed." I have checked and the
wuaueng.dll version is 7.6.7600.256, which I believe is the latest.
I have seen this result on multiple Windows 7 computers I have tested. None have worked so far. What is causing MBSA to report one thing and the target to indicate something else?
Ken Kemp Eddy County, NM IT

At this point, no. Since I didn't turn up an answer here, I've had to set this aside for more pressing matters. I hope to get back to it at some point soon.
If you are fortunate enough to find an answer, please be sure to share it here.
Ken Kemp Eddy County, NM IT

Diagnostics Agent 711 - SAP Host Agent - Installation on a cluster environm

Dear all,
We have the following architecture in our productive environment :
1. Cluster 01 is composed of 2 nodes.
   On Cluster 01, only "Database" and "Central Services" are running
   for 5 productive SAP systems.
2. Cluster 02 is composed of 6 nodes.
   On Cluster 02, only "Central Instance" and "Application Server"
   are running for 5 productive SAP systems
As read in "Diagnostics Agents installation Strategy", rules #4, slide 12 :
===================================================================
- Do not install a Diagnostics Agent on host that only run Database
or SAP Central Services.
- Install a Agent on EACH host running a Central Instance (CI)
and / or a Dialog Instance
===================================================================
For our productive environment, we do have to install Diagnostics Agents 7.11 on cluster 02 where we have CI + AS running.
Questions :
1. How do we monitor "database" and "central services" data on cluster 01 (DB + CS) as far as no "Diagnostics Agents"
   are installed ?
2. Do we have to install the new "SAP HOST AGENT" in our cluster 01 ?
3. As written in "Downloading and Installing Package SAPHOSTAGENT"
   guide, "you only need to install the host agent host taht not have
   an SAP Component". Does it mean that the new "SAP HOST AGENT"
   will have to be installed on our cluster 01 to monitor "DB+CS" data ?
4. What are for SAP a host that not have SAP Component ... ?
    "Database" and "Central Service" running for a SAP system should be consider as SAP Component or not ... ?
5. What is the difference between the new "SAP HOST AGENT" delivered by SAP today 23.11.2009
    and the "Wily Host-Level Introscope Agent"
   delivered by CA ?
Best regards
PC

Yes, it has to be installed.

Audit Vault Agent Installation issue

Hi All,
I have installed the following things
1) Audit Vault Server (10.2.2.0.1) on a Windows 2003 Server
2) I completed the post-installation tasks
3) I am trying to install Audit Vault agent (10.2.2) on HPUX (11.11) machine.
I start the AV Agent runInstaller, and fill the details like AVAgent name, Username, connect String etc, then click on next , it throws the following error:
"error1: the AV server is expecting an agent with the given name to be installed on another machine"
I am able to ping from Windows to HP machine and Vice versa (By IP Address and Hostname).
Can anyone tell me where i am going wrong and how to solve it.
Please mail to my email address ([email protected])
Thanks & Regards,
Rakesh

Hi,
The details of the installation done so far:
1) I have installed "Oracle Audit Vault Server (10.2.2)" on a Windows 2003 machine providing the following details
a) Audit vault Name
b) Audit Vault Home
c) Audit Vault Administrator
d) Administrator Password
e) Audit Vault Auditor
f) Ausitor Password
g) Database Vault Owner and Manager
h) Created a Audit Vault Agent user and added the user to the udit Vault server using AVCA.
2)I invoke the "Audit Vault Agent" Installer from a HP-UX machine and provide details viz.,
a) Audit vault Agent Name (Same name when i executed the AVCA command above)
b) Aduit Vault Agent Home
c) Agent Username
d) Agent Password
e) Audit Vault Server Connect String (Provide the Database details as mentioned in Audit Vault Server (localhost:port:servicename)
and when i click on the next button it throws me the following error:
"error1: the AV server is expecting an agent with the given name to be installed on another machine".
Hope this gives you a better idea. Waiting for your reply.
Thanks & Regards,
Rakesh

How to deployment for AV agent installation on RAC enviroment?

before the AV agent installation on RAC , the agentname and agentuser should be added to av server first. only one agentname/agentuser for the two nodes, or one agentname/agentuser for each node ? also ,the agentusr and the avsrcusr account only one account for two node ?
1. how to tell the agentname and agentuser account before agent installation ? more details are better.
2.with the 9i RAC DB at AIX, need install CRS first?
3. I setup an Linux cluster enviroment ,and a windows cluseter envirement(no CRS installed). but when install the agent , if the agentname set to hostname of the virtual IP ,the error is : ERR0R1: The av server is expecting the agent with given name to be installed in another machine. if input the agentname (which agenthost is node1) , it contiued,but no "node select GUI" comes up (according to the the GUI of Morgan's Library at: http://www.psoug.org/reference/audit_vault.html
),it executes a single agent installation on node1.
I don't know it's wrong configuration of my linux or windows cluster enviroment , or there are some import steps missed ?
it's urgent ,thanks!!
--the node's hostname and IP :
#public
192.168.0.11 node1
192.168.0.12 node2
#private
192.168.8.11 node1-private
192.168.8.12 node2-private
#vip
192.168.0.99 node
agentname: agentwin with agenthost node
agentname : agentwin01 with agentost node1
Message was edited by:
user634185

It is not urgent ... no one is drowning, your house is not on fire, so please don't abuse this forum. Thank you.
Audit Vault is auditing one database ... multiple instances. First create the RAC cluster the way you normally would. Then go to any single cluster node and install the agent. The agent installation will recognize that it is a cluster and ask you whether you want to install on one or all nodes and let you choose which ones.
There is no need to perform separate installations on each node.

11.1.0.1.0 agent installation failure

I have successfully installed 11g grid control on Linux RHEL 5 x86_64
While installing the agent using oms push on to other Linux RHEL 5 x86_64 machine in installation phase its getting failed. I am not able to figure it out how to resolve the issue.
The errors in log specified are like these
install.err Logfile content
ls: /opt/oracle/product/11gagent//agent11g/cfgtoollogs/oui/: No such file or directory
grep: /opt/oracle/product/11gagent//agent11g/cfgtoollogs/oui//: No such file or directory
grep: /opt/oracle/product/11gagent//agent11g/cfgtoollogs/oui//: No such file or directory
agentInstall.sh030211140140.log
Agent installation on node linuxserver1 fails for default shiphome
********************************

Hi ,
could you please check if the directories
/opt/oracle/product/11gagent//agent11g or /opt/oracle/product/11gagent/
do exist at all?
Have you installed an agent on the node before?
Please check the logfile "OC4J~OC4J_EM~default_island~1" of the OMS
for messages like
'agentpush_Install_NotDefaultShiphome' failed orThe action 'agentpush_Install_CollectLog' failed.
as well (could be found under $OMS_HOME/opmn/logs). If you have found those errors please let me know...
HTH

CCMS agent installation

Hi Experts,
I am doing SAP CCMS agent installation to monitor a non-SAP system which will be monitored by a Central monitoring system.
I have followed all the steps as:
http://help.sap.com/saphelp_nw04/helpdata/en/a8/adf7409b9d8531e10000000a1550b0/frameset.htm
http://help.sap.com/saphelp_nw04/helpdata/en/e2/eff640fa4b8631e10000000a1550b0/frameset.htm
1. communication user CSMREG in Central monitoring system.
Created the CSMCONF start file for CCMS agents in monitoring system.
2. CCMAGENT.SAR , SAPOSCOL.SAR , INSTALL_WIN.SAR
And done the configurations required in the monitored system.
3. Register the CCMS agent with CEN and start the agent. By following this step:
<hostname>\saploc\prfclog\sapccmsr.exe -R*
while registering the CCMS agent ,
I ma getting this...
This CCMS agent program sapccmsr is able to actively report alert data into the monitoring system[CEN], which is the central monitoring system.
to enable this feature, you have to setup the user CSMREG in [CEN].
After entering the RFC logon info for the user,
client:001
user:CSMREG
language:EN
host name:
load balancing:n
system number:01
router sting :optionla
trace lavel:0
password for CSMREG user:********
Its showing this error:
ERROR: RFC error during logon: 105 DESTINATION_NOT_EXIST
How to solve this?
Do I have to do any RFC configuration in the Central monitoring system(as I want to monitor a non-SAP system)?
urgently required.
Any help will be appreaciated.
Regards
Manisha

Hi Manisha,
Yes you will have to create a RFC and a suitable RFC user in the Central Monitoring System (CEN) via txn RZ21 to monitor these remote systems.
Please follow this link:
http://help.sap.com/saphelp_nw04/helpdata/en/a8/adf7409b9d8531e10000000a1550b0/frameset.htm
Please award suitably if helpful.
Regards, Dibya

Weblogic 81. portal server doesnot startup after the AM Agent installation

Hi,
I have a problem starting the weblogic server after I create the agent Authentication provider.
I have cross checked the CLASSPATH values and the JAVA_OPTIONS values.. it is correct
I get the following error
weblogic.security.service.SecurityServiceRuntimeException: [Security:090371]Problem instantiating Authenticati:
[java.lang.ClassNotFoundException: Can't load class: com.sun.identity.agents.weblogic.AmAuthProvider]
at weblogic.security.service.PrincipalAuthenticator.initialize(PrincipalAuthenticator.java:205)
at weblogic.security.service.PrincipalAuthenticator.<init>(PrincipalAuthenticator.java:262)
at weblogic.security.service.SecurityServiceManagerDelegateImpl.doATN(SecurityServiceManagerDelegateIm)
at weblogic.security.service.SecurityServiceManagerDelegateImpl.initializeRealm(SecurityServiceManager)
at weblogic.security.service.SecurityServiceManagerDelegateImpl.loadRealm(SecurityServiceManagerDelega)
at weblogic.security.service.SecurityServiceManagerDelegateImpl.initializeRealms(SecurityServiceManage)
at weblogic.security.service.SecurityServiceManagerDelegateImpl.initialize(SecurityServiceManagerDeleg)
at weblogic.security.service.SecurityServiceManager.initialize(SecurityServiceManager.java:734)
at weblogic.t3.srvr.T3Srvr.initializeHere(T3Srvr.java:822)
at weblogic.t3.srvr.T3Srvr.initialize(T3Srvr.java:670)
at weblogic.t3.srvr.T3Srvr.run(T3Srvr.java:344)
at weblogic.Server.main(Server.java:32)
Reason: weblogic.security.service.SecurityServiceRuntimeException: [Security:090371]Problem instantiating Auth:
[java.lang.ClassNotFoundException: Can't load class: com.sun.identity.agents.weblogic.AmAuthProvider]
Please help!!!
-Karun

Have you specify relative path or full of weblogic startup script? How's permission for user invoking startup script?
Excerpt from the docs as below:
Startup Script Location: Enter the full path to the startup script that is used to start your BEA WebLogic Server instance.
Have you installed the agent on the admin server instead of the managed server? It should be managed server.
Is this WebLogic clustered environment ? If it is a clustered setup; then you need to follow some specific steps to configure the managed servers. You are better off installing the agent on a managed server and copy the agent changes (CLASSPATH and JAVA_OPTIONS) to all the server instances. Some folks also prefer to copy these changes in commEnv.sh (easy way out) but we do not recommend this route since the server related JAVA_OPTIONS can be specific to each BEA server instance. Please note that the agent installer does not understand the template of admin server script. So, for a clustered environment :
1. Remove the present agent, restore the admin server script.
2. Install the agent on a managed server.
3. If there are more than one managed servers, put the agent startup script related changes manually in each of the managed servers.
4. Also note that you can start managed servers from console or command line. Depending on where you start managed servers, you will have to copy the agent changes to the respective files.
If it is not a clustered environment; follow 1 and 2 only. Could try it out and let us know what are your findings? Jerry

DPM Agent Installation Failed with Error code =0x80070643

Hi,
We had an Virtual Machine TFS server 2010 which had SQL server 2008 R2 installed on it.
On this Server we were running an DPM 2010 agent and it was fine.
Then I had uninstalled DPM 2010 agent and try to Install DPM 2012 R2 Agent on this Virtual Machine it gives me error 0x80070643. And for other VM the agent installation is fine.
When I checked on DPM agent logs in Windows/Temp folder it gives me below error.
I had tried with Deleting DPM Registry but still the Problem remains same.
Thanks

Hi,
Earlier the Protected Server had DPM 2010 Agent installed and while Troubleshooting I had already deleted the
HKLM\SOFTWARE\MICROSOFT\Microsoft Data Protection Manager\Setup Registry
And Tried to Reinstall Agent but still it gives same error.
Regards,
Nadeem

Preparing Solution Manager for SMD Agents Installation

Hello everyone
I have to configure the Solution Manager of QAS to receive new SMD Agents, I looking at the transaction SOLMAN_SETUP.
Does anybdoy know what do I have to do to prepare the environment for the installation of SMD agents?
Thank

Hi Marcelo,
Check note 1365123 - Installation of Diagnostics Agents, this note shows the agent installation strategy. You must install one SMD agent per host (physical or virtual) . The SMD agent should be installed in all host you want to monitor.
In order to connect the SMD agent into your Solution check the following WIKI:
http://wiki.sdn.sap.com/wiki/display/SMSETUP/Diagnostics+Agents#DiagnosticsAgents-Connectionoptions
Also, you can managed the SMD agent in the "Agent Administration", it can be found at:
- SOLMAN_WORKCENTER
- Tab Root Cause Analysis
- "Agent Administration"
I recommend you to use the "Direct connection to solution manager" for your agents. It is easier than the SLD registration.
Regards,
Allam

Dell OpenManage agent installation

Similar Messages

Maybe you are looking for