Dell Optiplex 745 CPU Ugrade

I saw in an earlier post that i could run this CPU in my PC:
QX6700 INTEL CORE-2 EXTREME 2.66GHZ 1066MHZ 8MB LGA-775 PROCESSOR
If i upgrade to this, will have have to get a new CPU fan to go with this or can i use my current one?

Cheeseman560
I saw in an earlier post that i could run this CPU in my PC:
QX6700 INTEL CORE-2 EXTREME 2.66GHZ 1066MHZ 8MB LGA-775 PROCESSOR
If i upgrade to this, will have have to get a new CPU fan to go with this or can i use my current one?
This is not possible for a 745. None of the Core 2 EXTREME series works.  You need at least a precision T3400 with Bios A09 with its performance heatsink and 525W power supply.  The QX6600 is a 130W Quad core CPU.
PROCESSOR
Intel® Core™ 2 Duo 1066MHz FSB Socket T with Dual Core technology  XD, EM64T, 2MB and up to 4MB L2 cache, EIST and VT (E6000 series)
Intel® Pentium® D 800MHz FSB Socket T with Dual Core technology  XD, EM64T, 2x2MB L2 cache,  EIST, and VT on 950/960 (900 series)  
Intel® Pentium® D 800MHz FSB Socket T with Dual Core technology  XD, EM64T, 2x1MB L2 cache  (800 series)
Intel® Pentium® 4 800MHz FSB Socket T with HT, XD, EM64T, and 1MB L2 cache  (500 series)
Intel® Celeron® D 533 MHz FSB Socket  T with XD and EM64T (300 series)

Similar Messages

  • Installation of Solaris 10 on Dell Optiplex 745

    Hi,
    I am new to Solaris. I am planning to install Solaris 10 10/08 on my Dell Optiplex 745 with the following config,
    Processor: Intel Core 2 Duo 6300 @ 1.86 GHz
    No if Bits: 64 Bits
    RAM: 2 GB
    HDD: 160GB
    Monitor: Dell 17" Plug and Play
    I would like to know if i can install Solaris 10 on this machine. If i am likely to face some problems, can you please detail the same.
    Thanks,
    Ashwin
    Edited by: AshwinMKumar on Mar 26, 2009 12:58 AM

    In the future, don't post a question to multiple forums.
    [http://forums.sun.com/thread.jspa?threadID=5376263|http://forums.sun.com/thread.jspa?threadID=5376263]
    (your answer in in your other post)

  • Problem with restoring an Image to Dell Optiplex 745

    Hello,
    i try to restore my image to my new Dell Optiplex 745 machines. I am
    using ZFD4.01IR7 with the boot-cd from zenimaging.info which uses the
    zfd7 imaging engine. I am able to restore the image but unfortunately my
    local (and only...) Administrator is not in the Administrators group
    anmyore. The Group membership shows only an SID, perhaps the old
    Administrators SID... So i cannot install drivers for the included NIC
    in order to use DLU for logging in with an Administrator from edir.
    I know that that is an unsupported environment with the mixed versions
    of ZfD but it works for other machines.
    Any help would be appreciated.
    Kind regards,
    Thomas

    On Mon, 26 Feb 2007 15:58:20 GMT, Thomas Degenhardt wrote:
    > The Group membership shows only an SID, perhaps the old
    > Administrators SID... So i cannot install drivers for the included NIC
    > in order to use DLU for logging in with an Administrator from edir.
    hmm.. bring down the image manually, remove the just imaged flag with
    zisedit from ZISD, start windows and check if that helps
    If you have already compiled drivers or have linux.2 please put them on
    http://forge.novell.com/modules/xfmo...ect/?zfdimgdrv
    Live BootCd and USB Disk from Mike Charles
    http://forge.novell.com/modules/xfmod/project/?imagingx
    eZie http://forge.novell.com/modules/xfmod/project/?ezie
    Marcus Breiden
    If you are asked to email me information please change -- to - in my e-mail
    address.
    The content of this mail is my private and personal opinion.
    http://www.edu-magic.net

  • M9748LL/A   vs  Dell Optiplex 745

    I am toying with jumping over  back to Apple since 1991 when I had to give up my Apple II/E for a AST PC.  I am looking at Powermac M9748LL/A and want to know if  I will be able to remove my memory from a DELL Optiplex 745 and put into M9748LL/A?   What about hard drive?

    Hello & welcome back... maybe!
    As far as RAM, that G5 needs...
    184-pin
    DDR PC3200
    64x8 device based 128x64 Module
    8 Non-Stacked TRUE PC3200 Devices per side
    Data Rate = 400MHz
    http://eshop.macsales.com/item/Other%20World%20Computing/3200DDR2GBP/
    Many PC3200 "PC" Value RAM or Stacked RAM will not work.
    On the Hard Drives, the G5 uses SATA1 1.5Gb/s drives, but depending what exact drives your Dell has, there may be workarounds.
    More info on that Model...
    http://www.everymac.com/systems/apple/powermac_g5/specs/powermac_g5_2.3_dp.html

  • Dell Optiplex 745

    When I try to image a dell 745 I get an error that says "No network
    device found. Load a network module first" what is the cause of this.
    What is the fix for this as well, can I just change some settings in the
    bios to get it to work or do I have to download something.

    Jortman,
    It appears that in the past few days you have not received a response to your
    posting. That concerns us, and has triggered this automated reply.
    Has your problem been resolved? If not, you might try one of the following options:
    - Do a search of our knowledgebase at http://support.novell.com/search/kb_index.jsp
    - Check all of the other support tools and options available at
    http://support.novell.com.
    - You could also try posting your message again. Make sure it is posted in the
    correct newsgroup. (http://support.novell.com/forums)
    Be sure to read the forum FAQ about what to expect in the way of responses:
    http://support.novell.com/forums/faq_general.html
    If this is a reply to a duplicate posting, please ignore and accept our apologies
    and rest assured we will issue a stern reprimand to our posting bot.
    Good luck!
    Your Novell Product Support Forums Team
    http://support.novell.com/forums/

  • S10 U3 on Dell Optiplex 745

    Has anyone gotten this to work? It "almost" seems to with some
    poking of the driver aliases etc. Can get the bge interface to be
    UP but not RUNNING and the ethernet addr is 0:0:0ish. Have
    put in the latest kernel patch and 125412-01.
    The NIC is either a BROADCOM 5751 or 5754 depending on who
    you beleive.
    Thanks.
    -T

    I tried to plug the OS11 bge driver into Sol10 but
    failed. I tried several methods,
    but all ended up with the modinfo entry showing
    version v0.49 of the broadcom
    driver being loaded. Weird. I've just finished trying the above, too. The problem you had
    can be avoided by moving aside the Solaris-10 bge driver files
    before installing the SUNWbge package. The S10U3 bge files
    are in /platform/i386/kernel/drv/ and .../drv/amd64/.
    However, even after the above, the SUNWbge driver fails to load
    on S10U3, complaining of many missing symbols. Likely this is
    due to the S11 bge driver having been moved into the new GLD
    network driver framework (so aggregation, etc. will be supported).
    I think the S10U3 kernel just isn't ready for SUNWbge yet, apparently
    not even with kernel patches up to today's level (125101-09).
    Note, however, that I did get the Broadcom-supplied bcme driver
    to work on the Optplex 745. This is the one downloaded from
    their "server" site, since there is no Solaris driver on their "desktop"
    driver section. I downloaded BRCMbcme package from:
    http://www.broadcom.com/support/ethernet_nic/netxtreme_server.php
    http://www.broadcom.com/support/ethernet_nic/driver-sla.php?driver=570x-Solaris
    It was necessary after installing the BRCMbcme package, to:
    update_drv -a -i '"pciex14e4,167a"' bcme
    After that, things are working normally.
    Regards,
    Marion

  • Optiplex 745 motherboard replacement

    looking for proper info to order replacement dell optiplex 745 motherboard. what numbers should I look for?
    Thanks Guys!!!

    You're very welcome!
    Thank you for your acknowledgement of my service to our country. It was an honor to serve.
    I would have been very happy to help if I had known the answer to your question.
    I help anyone I can with drivers from different brand PC's, but I don't have any info on part #'s, etc.
    In other words, I am not a HP "snob."
    Happy Holidays to you too!

  • Slow Taskbar Clock on Dell Optiplex 960

    I just installed Windows 7 RC Build 7100 32-bit version on 2 brand new right out of the box Dell Optiplex 960. This was a fresh install not an upgrade. The setup ran just fine. Windows boots up and runs but is sluggish and sometimes I have to wait for things to open. Such as running solitaire it is slow to deal the cards and even stops briefly.
    I also tried the 64-bit version but receive an error during the boot from DVD. Status 0xC00000e9. Info: An unexpected I/O error has occurred.
    The cpu and memory usage are not high at all. I have also noticed that the time on the taskbar is running very slow. It takes about 45-50 seconds for one second of time to pass.
    I am wondering if maybe there is a driver issue with the machines. I have installed the Windows 7 video driver from the ATI site. I am not sure where to find a chipset driver for this computer. There are no red X's or other problems in the device manager.
    Any help would be appreciated.
    Computer specs.
    Optiplex 960 Minitower
    Core 2 Quad Processor Q9650 (3.0GHz, 12M, 1333MHz FSB)
    4GB DDR2 Non-ECC SDRam 800MHz
    256MB ATI Radeon HD 3450
    320GB HD

    I wonder if xperf may show something about what's going on...
    Download and mount the Windows 7 RC1 SDK  ISO which contains xperf 4.5.  The MSI for the Windows Performance Toolkit appears to be in the \Setup\WinSDKTools_amd64\cab1.cab file.  Install the the Windows Performance Toolkit from there, and then, from an elevated CMD prompt change to the folder containing xperf.exe and execute:
     xperf -on DiagEasy+PROFILE  -stackwalk Profile
    Then, just after reproducing the problem, run:
     xperf –d merged.etl  
    Then, ZIP merged.etl and password protect it.  Upload the ZIP file somewhere, and share the location either publicly or privately.  Share the password privately...   (My email address is in my profile.)

  • Dell optiplex 755 won't boot with NI PCI Fieldbus card installed

    After installing NI Configurator 3.1.0 on new Dell optiplex 755 and then installing the NI PCI Fieldbus card the pc won't boot up.
    This card works fine 745 and older dell pc's.
    Anybody else having this problem?

    Hi,
    In which step does the boot process fail? Is there any error message?
    After installing NI-FBUS 3.1, please go to Windows Device Manager, check whether the driver of PCI-FBUS is correctly installed. There should be no any error in Device Manager.
    You can try the following methods.
    1. Change to another PCI slot.
    2. Use Windows XP. NI-FBUS 3.1 does not support Windows Vista.
    3. If there exist other PCI devices in the system, remove them and try using PCI-FBUS only.
    4. Update the drivers of Dell Optiplex 755 if there are new versions, including video card, ethernet card, etc.
    Feilian (Vince) Shen

  • Apex giving installation problem on dell optiplex xe system

    Hi
    We have installed apex 4 on dell optiplex xe , but it display the source code when we use page forwared and backward of mozilla firefox. We also use the same versionon our laptpops and other non branded computer , it working fine.
    Regard
    Faiz

    This case is similar to the case handled by Jurgen Keil on Digest Number 385 except that my case, it has a different error message.
    At the prompt "Select type of installation" (or the prompt
    "Select (b)oot or (i)nterpreter:", I type the command "b kadb -d". I see a General Protection Fault and some messages which cause the system to reboot. But I can't capture all the errors/messages cuz there's no system dump device configured.
    How do I configured the system dump device so I can send you more details?
    Thank you.

  • Repeated blue screen crash when running labview 8.2 on Dell optiplex GX620

    Hi, I have recently experienced a series of 'blue screen' crashes on a Dell Optiplex GX620 while running Labview 8.2. The dell is running Windows XP SP2 with an ATI Radeon X600 graphics card. Labview is interfacing with a NI DAQPad 6015 device. The computer is a dedicated Labview machine so there is no other third party software that has been installed that could be causing the problem. Also, the computer is one of three identical machines, the only one that has labview installed and the only one that is crashing. Upon rebooting after the first 'blue screen' crash an error report indicated that there was a problem with the ATI graphics driver and suggested updating the driver to the latest version. This was done. Upon rebooting after the second 'blue screen' crash an error report indicated that there was a problem with the RAM. Both of these crashes occurred while running a labview application. A further two incidents have occurred where the computer has restarted for no apparent reason while running a labview application. I was wondering if you were aware of any known issues/incompatibilities with my specific machine and labview 8.2, or if there could be any other known issues with labview that might be causing the crashes. It should also be noted that this is a new setup and these crashes have occurred in relatively short time frame. Thanks for your help!

    Hi,
    To have a better understanding of what is causing the blue screen crash and the Windows restart, we may need to retrieve the memory dump caused by the crash in Windows XP.  Before we actually get into that, we may need to disable Automatic Reboot by Windows when it crashes.  I have attached a link that describes how to disable computer reboot after a crash and I have also attached a link of how to retreive the memory dump.  Let me know how it goes!
    Why Does My Computer Automatically Reboot For No Reason?
    How Can I Create a Kernel Memory Dump When Windows Crashes?
    (Note that we want to select Complete memory dump, not Kernel Memory dump)
    Regards,
    Nadim
    Applications Engineering
    National Instruments

  • Officejet Pro 8500 A909g Scan-To-Network-Folder Problem On New Dell Optiplex 3020

    I hope that I am posting this issue to the correct board.
    I recently purchased a Dell Optiplex 3020 64-bit desktop running Windows 7 Pro. My home network now has the old HP printer and my original 2003 vintage Sony Vaio XP Home 32-bit on wired connections. There is also an HP Notebook 64-bit running Windows 7 Home, using a WiFi connection. I replaced a Linux clone (which had connected ok to the printer) with the new Dell on the same wired connection.
    With the other 2 PCs, I was able to set up Scan To Network Folder using the original HP software with no problems. I used a current setup file from the HP site to set up the Dell. The file is: "OJP 8500vA909_Full_14 HP Webpack". The Dell prints fine, but when I try to set up the network scan folders on the Dell the setup stalls and I get a request for an SSL certificate. I don't know if this is being generated by the OS or by the HP setup file that I downloaded. I can't figure out how to get the network folders to work on the new Dell, and I know next to nothing about SSL.
    To be clear, the old Sony is a 32-bit Windows Home Edition, the HP notebook is Windows 7 Home 64-bit, and the new Dell is Windows 7 Pro 64-bit. Any suggestions will be appreciated. Sometime soon, the Sony will be retired and the OS environment will become much simpler.
    While I'm at it, I probably should update the printer firmware. However, my guess is that I should wait to do that until the old 32-bit Sony goes out to pasture.
    TIA for any advice and suggestions.

    Hi Alla-guy,
    As far as I know, you have posted your issue to the correct board, now let us see what we can do to get it resolved
    I will answer your easier question first, in regards to the firmware. You can update the firmware whenever you are ready! You don't need to wait for the other computer to reach it's end, as the firmware is just within the hardware of the printer and shouldn't affect anything software wise on the computer, so go ahead and update the firmware when you have a few minutes!
    As for the setting up to scan to a network folder, it is odd that it's asking for SSL, do you know if you're the administrator on the new computer?
    I realize the instructions in this Set up and Use Direct Digital Filing for Windows document are for setup, but still have a look and make sure that is how things were going for yourself. Also, it may be a good idea to check any firewalls or anti-virus that you have and temporarily disable any firewalls or programs that could be blocking things over the network.
    Let me know how this goes for you!
    Please click “Accept as Solution ” if you feel my post resolved your issue, as it will help others find the solution faster
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    **MissTeriLynn**
    I work on behalf of HP

  • Help! I need to upgrade my Dell Optiplex GX260 (tower) power supply!

    Hi,
    I plan on taking a trip to Best Buy today to purchase a video card and power supply for my Dell Optiplex GX260 (tower).  I am looking to get at least a 500W power supply.  Can you tell me the BEST power supply that will work/fit that Best Buy sells?  Thanks very much.

    I see that you posted back in March of 2009 so I hope that you haven't already fried a motherboard or PSU while learning the hardway, as I feel that I almost did. We have a Dell GX260 that my daughter wants to play some games on but I found out that the Graphic Card (ATI Radeon 7500 series) was not good enough for the games that she wants to play so I decided to upgrade the graphic card, unfortunately I found out that a lot of newer cards have PCI-Express connectors and not the PCI I need. As well, I found out that most of the PCI cards above what I have need more than the 250Watt power supply that I have. So I thought, why not just upgrade my my PSU and then I found out that Dell actually rewires their PSU differently than the industry standard ATX connectors but I see a lot of post and recommendations from people that say that you can use any store bought PSU to upgrade your Optiplex GX260 but BEWARE that if you bought your system after late 1998 then you have a Dell system that has their own proprietary wiring configuaration and even though you can buy a standard ATX PSU at bestbuy and it will seem to fit properly, it will either fry your new PSU or worse yet, it will fry your motherboard as well.  In fact, I went to bestbuy three days ago and bought a graphic card and the salesman told me that if my PSU was not at least 300Watt, which is what the card required, that I can come back and buy a standard PSU from them and that would fix the problem. The salesman even knew that I had a Dell System so I wonder if BestBuy would be willing to replace my motherboard if I had fried it based on what the bestbuy salesman told me to do???? Anyway, read this link http://www.informit.com/articles/article.aspx?p=339053 and see what you think!!  I am glad I stumbled across the information and plan on upgrading my PSU with a compatible Dell PSU or look for a Dell Converter (if there is such a cable) or just replace both my PSU and Motherboard as directed.  I also think I might actually build my next PC from scratch with all industry standard parts, as I was very ignorant up until now that Dell was doing this to their products and I have 3 of their systems in my house....but no more!!! I did find a Dell compatible PSU 500 Watt on PCPower.com but it comes with SATA drive connectors and my Optiplex GX260 has IDE connectors so I don't know if I can get a SATA to IDE conversion or not but as you can see I am still researching my options. I might actually find it will be cheaper to just buy a new system or build the one of my dreams!!  
    I know I wrote a lot but I hope that this information is helpful to someone else out there who is in the same boat as me.

  • Can I install Mac OS X Tiger 10.4 on a dell Optiplex Gx280?

    Hi! I have a couple of questions which I can't seem to find the answers too.
    1) Can I install Mac OS X Tiger 10.4 on a Dell Optiplex GX280?
    2) Can I take the HDD from the aforementioned Dell and place it in my Power Mac G4 Digital Audio? If so, will Tiger still be on it?
    3) If I can't install Tiger on my Dell, can I rip the DVD drive out and use that to install?
    4) HDD's don't have to be Mac specific, do they?
    Thank you for your valuable time,
    Obiwan-Kenobi

    Can I install Mac OS X Tiger 10.4 on a Dell Optiplex GX280?
    10.4.8 has been done:
    http://wiki.osx86project.org/wiki/index.php/HCL_10.4.8/Desktops
    If you want further info, don't ask here.
    Use Google and search terms "Dell Optiplex GX280 hackintosh" to search the x86 sites.

  • Installation of  Solaris 10 x86 9/10 on  Dell Optiplex 780 machine.

    Hi All,
    I am gettting the below error while trying to install Solaris 10 x86 9/10 on Dell Optiplex 780 machine.
    Error: The disk you inserted is not a Solaris OS CD/DVD
    Any suggestions how to resolve this.
    Thanks

    I have modified the BIOS settings as below to resolve this issue.
    BIOS menu -> Setup -> Drives -> SATA Operation -> check the "Legacy" box
    I suspect that Solaris installation not detecting the Hard disk of DELL Optiplex 780 machine.

Maybe you are looking for

  • IPad 2, restore & setup as new, then restore from backup?

    Confused yet? I am! So here we go, yes, I'm new to the forum, I've had my iPad 2 since Oct. 2011. And No, this problem isn't in my head. Last week, I finally updated to iOS 5.1.1, and I deeply regret doing so. I had NO issue before the update, and no

  • Special/Swedish characters in an AXL request

    Hello, I am developing an application that is adding a user to the Call Manager (4.1). When I try to add a name with swedish characters (???) the CCM changes them to question marks "?". I have tried adding the swedish characters unicode encoded, ? =

  • How reduce pop up ads without completely blocking pop-ups

    All of a sudden ads pop up all over my browser. How can I stop this from happening. But I don't want to turn on block all plug-ins.

  • Writeback and Deployment Services

    We are planning on a major infrastructure improvement for an overloaded Essbase OLAP server. One option was to use deployment services to cluster two (or more) servers. The load balancing and failover protection would be of great value. The problem i

  • In middle of sync, iTunes crashes. (Windows XP)

    *I am not good with computers, and I am a teenager. I need help. Whenever I try to put a song on my iPod Touch 2nd generation, my computer, or try to import a CD to iTunes, iTunes crashes and says "iTunes has encountered a problem and needs to close.