Denon 791 Receiver and Apple Tv
I have a Denon 791 Receiver and Apple Tv. Which source do i connect the apple Tv to? thanks
I also have an AVR-2113 and am experiencing this issue with Apple TV 3G. I have to switch everything off for up to a minute, sometimes disconnect the HDMI cable and then switch it all back on again. I haven't worked out which order I need to turn stuff on in. Sometimes it takes me about 5 attempts before the things works.
It usually goes like this:
* Turn everything on
* Apple logo appears
* Apple logo disappears, I receive a warning from the TV that there is no HDMI signal
* pull out the HDMI cable from the Apple TV
* DENON logo appears on the screen
* plug it back in
* No HDMI signal warning message reappears
This sounds like some HDMI handshaking issue between the Apple TV and the Denon receiver. Is this Apple's fault, Denon's, or a mixture of the two?
Similar Messages
-
Denon AV receiver and Apple TV
Why doesn't Apple TV show picture or sound when hooking up in Denon AVR-1912 receiver? Apple TV works fine when plugging directly into TV.
I also have an AVR-2113 and am experiencing this issue with Apple TV 3G. I have to switch everything off for up to a minute, sometimes disconnect the HDMI cable and then switch it all back on again. I haven't worked out which order I need to turn stuff on in. Sometimes it takes me about 5 attempts before the things works.
It usually goes like this:
* Turn everything on
* Apple logo appears
* Apple logo disappears, I receive a warning from the TV that there is no HDMI signal
* pull out the HDMI cable from the Apple TV
* DENON logo appears on the screen
* plug it back in
* No HDMI signal warning message reappears
This sounds like some HDMI handshaking issue between the Apple TV and the Denon receiver. Is this Apple's fault, Denon's, or a mixture of the two? -
Denon AVR-1909 and Apple TV reverting back to 720p
I have my Apple TV running through my Denon AVR-1909 amp (HDMI). If both units are off and I start them up, my Apple TV reverts back to 720p resolution. The resolution before I turned off the Apple TV is set to 1080p.
It wasn't until I ran the Apple TV through this Receiver did I start experiencing this problem.
If the receiver is already on, then the resolution on Apple TV remains at 1080p when I turn it on.
I'm using a Harmony One Remote to Turn on my devices. I have setup the functionality to Start the receiver first, then I have a created various delays before it starts the Apple TV, thinking that the amp needs sometime before it sends a signal. Even with this delay, the problem still exists.
Is anyone else experiencing this issue, and is there a fix?
Any help would be greatly appreciated.Welcome to the Apple Community.
Contact the developer of the Air Video app. -
after upgrading to iTunes 11.01.12 the air-play button disapeared. the apple-TV3 and the receiver can communicate, but in my computer there is no button to play on any other speaker/unit. it seems that iTunes can find them. i did everything on the checklist, like check that all units are connected to the same wifi and have the latest firmware.
after upgrading to iTunes 11.01.12 the air-play button disapeared. the apple-TV3 and the receiver can communicate, but in my computer there is no button to play on any other speaker/unit. it seems that iTunes can find them. i did everything on the checklist, like check that all units are connected to the same wifi and have the latest firmware.
-
Does Denon AVR-x1000 cooperates with Apple TV 3rd generation perfectly?
Is someone tried that?Search the forums or google and find out for yourself.
Do you have a specific issue? -
I have a Denon 1913 AVR and Apple TV. Doesn't work...
The Denon won't pass through the video to the TV. I connected the HDMI directly to the TV and the optical out to the Denon, but the audio won't come through (apparently optical audio can only come from the TV). Any suggestions?
Thanks, Rudegar, same set up here, but the Denon won't seem to accept the optical in unless it's from...the TV! It's a very powerful AVR, but has some distinctly user unfriendly tendencies. Funny thing, I have a Sony and could easily set it up to do that. Thinking of just getting rid of the Denon, in spite of its superior sound. Was hoping someone has had the same problem, so to speak.
-
I have an HDMI connection to the receiver and on to the TV - but there is non audio from my Apple TV. Not for movies, music, YouTube etc. I have checked all of the connections and the video is xlnt. Have also toggled thru all possible Dolby/Audio combinations in settings. Help! Any suggestions?
Hello again Parker -
The basic setup is Digital Cable Box, DVD Player, Denon Receiver/Amp and TV Monitor. To that I added the Apple TV. The Receiver only has two HDMI IN slots (one for cable and one for the DVD) and one out to the Monitor.
[I bought a switcher to toggle the DVD and the AppleTV back and forth but just disconnected the DVD to simplify when I ran in to trouble.]
So now I have:
HDMI from the Cable Box to the Receiver
HDMI from the Apple TV to the Receiver (in the old DVD slot which always worked well)
HDMI from the Receiver to the Monitor
RCA's from the Receiver to the Subwoofer and the other speakers
In addition I have some backup connections:
S-Video, Optical Audio and L/R RCA's from the Cable Box to the Receiver
S-Video from the Receiver to the Monitor
Wait - JUST FOUND IT!
By going thru the excercise to track all of the connections per your suggestion, I found an anomaly when I switched Receiver sockets for the HDMI links. The video moved but the audio didn't. Turns out the monitor was using the optical audio feed from the receiver. So I disconnected the optical audio and the monitor automatically switched to the HDMI audio feed! Looked promising...
So I first connected an optical audio feed from the ATV to the receiver - Audio! Then I pulled it, but the audio didn't switch to the HDMI feed. It stopped. Would be OK if all I was going to use is the ATV, but I need the DVD player too and I can't use a switcher to toggle between them if I have to unplug the optical audio each time.
This is becoming a career! Any suggestions?
Will -
I am fed up with Spring and Apple passing me off to one another and neither will fix the problem. I am unable to receive a connection on my phone.
The internet goes out and I have to reset network setting each and every time. This is only a temporary solution which by the time I release the line with Spring or leave the apple store the issue is back. Sprint indicates that it is a know issue with the Iphone 5 and apple says it is a network issue as Sprint's network is not up to par with the Iphone and can not meet the expectations on the Iphone 5.
I have attached a few picture, as you can see it clearly says I have 5 bars and 3g available but I have no connections what so ever.
This issue affects all data and so I can not send or receive picture messages, use apps, or access the internet. The data goes in and out intermittently and it seems the phone chooses what I can and can't do.
For example I can watch Youtube or Vevo videos but I can not access Facebook or Instagram.
Is anyone else having this issue?
I will soon loose my patience....
I have reset my phone three time and have reset network and other setting mutltiple times. -
Just hooked up my Apple TV. It's great. I have a satellite receiver and also a multi room sound system where I would like the sound to come through. Can anyone tell me how I would connect to accomplish this. My HDMI is connected so the sound is coming through my TV just fine. I would like it to come through my sound system instead. Your assistance is very much appreciated.
goaliemother wrote:
Hi:
My system is as follows. 1 only HDMI output on TV. I purchased an HDMI switch box/unit. I have the output from the Switch Box Unit going into my TV.
I have 5 inputs on the switch box unit. 2 I have used.....
1 input from my television satellite receiver
2 input from my Apple TV
My other equipment is
1 home theatre system. This is where the sound from my TV goes through
1 russ sound whole home sound distribution system
When I play my Apple TV I am still getting the sound of my satellite TV.
This suggests that your satellite receiver is connected to your "home theater system" (which I will shorten to AVR "Audio/Video Receiver") for audio. Is this correct?
If so, then your problem is that you're switching video inputs, but not audio, and what I listed as (2) applies:
2. You can connect the ATV to the TV using HDMI. Then you can either:
2a. Connect the TV to the AVR using an optical cable for audio.
2b. Connect the ATV to the AVR using an optical cable for audio.
You've connected the ATV to the "switch box" instead of the TV, which amounts to the same thing, as you're just expanding the number of HDMI ports on the TV by using the switch. So your simplest solution is either 2a or 2b. If your TV has an audio out port, and it's the same kind of port that your satellite receiver uses, you can just disconnect the audio cable from the satellite receiver and plug it into your TV. You may have to enable "external speakers" or whatever they call it in the TV settings. This would be best, because then you wouldn't have to change inputs on the AVR to select the correct audio; you would just change inputs on the switch, and both video and audio would switch between the satellite box and the ATV, solving your problem. Note that an optical cable is required to get Dolby Digital 5.1 audio (surround sound), and I mention that because it's possible you're using an analog audio (RCA) cable. So an optical cable is best.
Beyond this, I would really need to know your TV and AVR model numbers, preferably accompanied by links to specification pages or manuals, and it would be very helpful to know how the satellite receiver is connected to the AVR for sound. -
I bought an IR receiver and an Apple Remote, and I can't get it to work. What am I doing wrong?
I bought an IR receiver and an Apple Remote, and I can't get it to work. What am I doing wrong? The receiver is a Lenovo eHome OVU430006/01 USB IR Receiver.
Hello,
You would need to pair the Apple Remote with the receiver. So I would use the generic Mac/PC receiver and follow these instructions:
http://support.apple.com/kb/HT1619
If that doesn't work then check in System Profiler to see if the IR receiver has been recognized by the PowerBook's hardware. You may require the install of drivers for this device to be recognized.
Best of luck -
i am using one apple id for facetime in my iphone and mac. my phone is able to receive and make calls while my mac is not able to do both. what is the problem.
thanks. your answer was correct, clearer. I have another question, maybe you can answer. I just purchase my ipad2 2 days ago. yesterday, there was a sound. today there is no sound. there is a sound only in movies and you tube and music. but no sound on all apps and keyboards. I look it up and seems like ther are few that have this problem. I called walmart coz I bought it there and they told me that they have not heard that before but if I can't fix it, just return it and exchange it with anew one since I have 14 days to do that. I tried rebooting it and still won't work. Should I just restore it?
-
i have an older yamaha receiver and projector both without hdmi inputs but component video instead. I would like to get apple tv and start renting movies through iTunes but apple tv only supports hdmi and ive read that iTunes has codes to prevent the use ot analog cables with movies. Is there a way to adapt hdmi to component video for both apple tv and iTunes easily?
Yes, HDMI is the only supported method. Also, with converters you will run into issues with HDCP (which will prevent you from streaming DRM content from iTunes etc) as well as resolution.
-
My wife and I share the same email address and Apple ID. We are not able to send and receive Text Messages to one another. Is the cause of this because we share the same Apple ID? Will we have to set up 2 separate primary email addresses to be able to send and receive Tex Messages to one another? Like I said, we share the same email address and woul like to keep it that way to keep up with our email together. Is there a way to by-pass having to set up 2 primary emaill addresses if this is the problem?
Thanks.go to the settings and turn off imessage
but that don't change the issue that you will never be able to facetime eachtoher
the appleID is really meant as the handle that identify you it was not meant to be shared
but can see that people may want to do not buy apps more then once -
I somehow seem to have changed the Apple id password on my iPad and don't know what it is. When I try to reset it, I'm given the option of having Apple get in touch with me by email. I click on this choice and Apple says the email has been sent - but I never receive it, even though the address is valid. The other option is to answer two questions preceded by entering my birthdate. I know the answers to the questions, but must have entered my birthdate incorrectly when I set up the account. To make a long story short, I can't sign in to iCloud on the iPad and can't figure a way out of this dilemma.
Your password was sent to your emergency email address. Perhaps you have an email you never use? I use the free email from my cable TV account as my emergency email.
Your Apple account and cloud account are separate. You could even have completely different user and password. Most of us use the same user ID and password, but they are not the same thing, don't mix them up.
If you can't retrieve emergency email, you will have to call apple support.
http://support.apple.com/kb/HE57 -
Trying to install the latest update for itunes...error received "service apple mobile device failed to start. verify thay you have sufficient priveleges to start system services"...? I have uninstalled and tried to reinstall???
Hello Kimberly0914,
It sounds like you have tried to launch iTunes after a recent update due to this error message, and you cannot install iTunes after uninstalling. I recommend the troubleshooting from the following article to help you named:
Issues installing iTunes or QuickTime for Windows
http://support.apple.com/kb/ht1926
Then download and install iTunes with this link:
http://www.apple.com/itunes/download/
Thank you for using Apple Support Communities.
Cheers,
Sterling
Maybe you are looking for
-
At my wits end with Bt usage monitor
I keep getting emails stating I have gone over my broadband usage stating I'm using 100+gb in a month. I know this is not the case as I have been logging into my homehub which tells a different story. It has been connected solid for 15 days and I hav
-
Sometimes my iPad asks if I want to verify by answering questions or by email. When I choose to answer questions, it asks for my birthday but then tells me it is an error. Also when I try to sync iTunes from laptop to iPad, it only goes from iPad to
-
There are two major interface gaffs in Safari 4. The first is moving the tabs back to the bottom without giving the option to leave them on top -- you know, they way they were for the entirety of the beta -- and the second is the loading image. It's
-
Upgraded iMac to OS x 10.10.1 and now find that Photoshop CS3 (606) crashes after launch. It seems to make progress to the point where the menu bar is presented and then crashes. I've searched for others with this problem and tried various recommende
-
Spatial and MV - migrating from one server to another question
If we want to migrate from one MV server + database to another one - is it possible to automatically export/import map cache definitions (MDSYS.SDO_CACHED_MAPS_TABLE)? and MDSYS.SDO_GEOM_METADATA_TABLE ? - this metadata table imports only references