Desbloquear de fabrica.

Hola soy de Chile y tengo un Iphone con la compañía movistar, ahora estoy en ecuador y necesito desbloquear de fabrica mi iphone para poder utilizarlo acá, alguien me podría ayudar?

Only the Carrier who sold the iPhone can unlock it, as per their unlocking policy. Contact them.

Similar Messages

Si tengo un iphone modelo mc319ll de apple como se puede desbloquear

si tengo un iphone apple con modelo mc319ll se puede desbloquear de fabrica ya que estoy en costarica y no funciona como se puede hace

No. La memoria no es cambiable/remplazable.
Vende el telefono tuyo y comprate uno con mas capacidad.

Error on nexus 7k series " operation failed.the fabric is already locked"

getting following error on nexus 7k series switch: error is " operation failed.the fabric is already locked", while removing ntp commands (no ntp server 10.101.1.1) from switch. Please help.

I had the same error message, only in my situation Outlook would only open successfully every 4 or 5 attempts. When Outlook would open (versus just hanging at the splash screen), I would get two dialog boxes with the warning/error message.
After I clicked okay I could get into Outlook.
Previously I experienced this problem running my Office 2010 client with my Exchange 2007 mailbox on my old laptop. The problem followed my mailbox through an Exchange 2010 migration (so new Exchange org), client upgrade to Outlook 2013, and a new
laptop (so I knew it wasn't a corrupt profile). This led me to the conclusion that it was a corrupt item(s) in my mailbox.
To resolve the issue, I archived *everything* in my mailbox to a PST file, ran SCANPST to fix the corruption, and then uploaded everything back into my Exchange mailbox one folder at a time, stopping after each folder to close and restart Outlook so I could
narrow down which folder had the corrupt item if the problem recurred. I'm happy to say my issue is now resolved.

Fabric Manager - do I need to install server component?

Hi,
I would like to know if I need to install the server component of Fabric Manager, or if I can just use the client component to manage the switches directly.
I have 2 MDS 9120 switches which will be run as 2 separate fabrics. They will be used in a non-production environment and I will need to configure VSAN and zoning using pWWN. If I do need to install the server part, what is the benefit of using the licenced version over the unlicenced?
Thanks, Darren.

Darren,
The choice to install and licence the server component would be to manage your entire SAN fabric as a holistic centralized topology versus using the client which pretty much only allows you to view the fabrics individually within Fabric Manager.
For a small non-production environment like yours you will be fine, but if you find yourself in a situation where your fabric is becoming a larger Production enironment then I would recommend moving to the licenced server version.
regards
Alan

Is there a way to see SAN luns from the UCS fabric interconnect.

Hello,
I have recently added a 3rd and 4th vHBA to a B440 running RHEL5.
Originally I had 2 vHBAs', and each created a path to 172 luns. (I was multipathed to 172 luns)
Now I have added two additional vHBA's and my SAN admin assures me he has mapped, zoned and masked all 172 luns to the 2 new vHBA's.
So, at this time I should have 4 paths to 172 luns....but I don't.
What I see is 4 paths to 71 luns.
I still see 2 paths to all 172 luns, but only see 4 paths on 71 of them.
Its almost like my SAN admin either mapped or masked only 71 of the 172 luns to my 3rd and 4th path.
Via the RHEL5 OS I have rescaned the FC paths, rebooted, done lsscsi, looked in the lowest level places for what devices are present on my FC channels, always I see 172 devices on the 2 original FC paths and 71 devices on the 2 new FC paths.
My question is....is there a way to see all devices (luns) accociated with an vHBA from the command line in the Fabric Interconnect?
My configuration is UCS w 2 FI's, using 8Gb FC connections to Cisco 9500 directors, to an EMC DMX4.
Thanks in advance,
Gene

wdey,
The link you supplied in your response is the answer.
You can look at the devices on the FC boot paths, but not while the OS is running.
I have a test server I could reeboot to try what you have in your document, and it does work.
Too bad Cisco could not create a linux util rpm that would allow looking down the fabric while running. Im quit sure emulex has this kind of util, called HBAanywhere...at least for solaris.
In any case, thanks for the link to your article, it was VERY good!
My problem with seeing a shorter list of luns on 2 of my FC paths may get solved this afternoon by a change my SAN admin is going to make.. If it does I will post the fix.

When trying to upload a cd onto itunes it chooses to chop the original cd into 4 separate albums and mix up the track order. Any ideas why and how to overcome this problem? ( the cd is guy gerber and called fabric 64)

When uploading a cd onto itunes on my imac it has choosen to copy the original cd into 4 seperate cds and mix up the track order, particularly annoying as this is a mixed cd (Guy Gerber, fabric 64) . Any ideas why when everthing else copies perfectly and how to rectify this problem?

See Grouping tracks into albums.
tt2

Can no longer open Fabric Manager Web Client 4.7(2b)

Hello
I have recently upgraded from Fabric Manager 3.3(2b) to 4.2(7b). I followed the correct path, so went from 3.3 to 4.1 and then from 4.1 to 4.2.
The application opens but I can not browse to the localhost address on either http or https and there are no Cisco related services running, or, even available. Additionally, the server is no longer listenning on port 80 or 443.
Does anyone know of what might be happenning here because at the moment, trying to get to the server from itself, or remotely, just brings up a "page cannot be displayed" error.
Many thanks in advance
Anthony
p.s. I have rebooted since the rebuild.

Hi
Yes, the PostgreSQL service has started but there is not even a Cisco Fabric Manager service visible, nor a Fabric Manager Web Client service. I can open Fabric Manager and it works, just no services and I cant open the Web GUI.
Thanks for replying
Anthony

Enabling VM Guest NLB w/Multicast IGMP on 2012 Hyper-V host w/ converged SCVMM fabric switch

What a mouthful.
As short as possible:
WHAT I'M ATTEMPTING:
I'm trying to build a new NLB cluster for a 2008 R2 SP1 Remote Desktop Services farm. And I'm trying to do it the right way, with multicast igmp, not unicast.
The two guest VMs with NLB install converge fine. VIP gets this:
IP: 192.168.100.157
MAC: 01-00-5e-7f-64-9d
NLB NIC is on the same VLAN & "Converged switch" in VMM as our mgmt/server traffic (That is to say it's on production VLAN, not on a separate vlan)
PROBLEM:
Can't ping 100.157. From VM guest itself, from host, or from Cisco 6509 switch.
Cisco show mac address lookup does not see that MAC anywhere
show ip igmp groups shows not igmp traffic at all. Clearing counters show sno multicast increment.
FURTHERMORE:
Host is setup thusly:
- Dell R810
- 8x1GbE Broadcom 5709c in a Server 2012 LACP/HASH team built via VMM powershell cmdlets
- On the physical switch side, those 8 nics are in a Cisco port-channel, trunked, all VLANs allowed
- Host has no "physical" nics per se, as in a 2008 R2 hyper-v host. Instead Host has these:
Set-VMNetworkAdapter -ManagementOS -Name "Live Migrate" -MinimumBandwidthWeight 35
Set-VMNetworkAdapter -ManagementOS -Name "MGMT" -MinimumBandwidthWeight 25
Set-VMNetworkAdapter -ManagementOS -Name "CSV" -MinimumBandwidthWeight 40
Set-VMNetworkAdapter -ManagementOS -Name "iSCSI #1" -MinimumBandwidthWeight 0
Set-VMNetworkAdapter -ManagementOS -Name "iSCSI #2" -MinimumBandwidthWeight 0
Set-VMNetworkAdapter -ManagementOS -Name "Aux" -MinimumBandwidthWeight 0
Get-VMSwitch outputs this on the converged v-switch:
ComputerName : My-host
Name : My awesome switch
Id : e2377ce3-12b4-4243-9f51-e14a21f91844
Notes :
SwitchType : External
AllowManagementOS : True
NetAdapterInterfaceDescription : Microsoft Network Adapter Multiplexor
Driver
AvailableVMQueues : 0
NumberVmqAllocated : 0
IovEnabled : False
IovVirtualFunctionCount : 0
IovVirtualFunctionsInUse : 0
IovQueuePairCount : 0
IovQueuePairsInUse : 0
AvailableIPSecSA : 0
NumberIPSecSAAllocated : 0
BandwidthPercentage : 0
BandwidthReservationMode : Weight
DefaultFlowMinimumBandwidthAbsolute : 0
DefaultFlowMinimumBandwidthWeight : 1
Extensions : {Microsoft NDIS Capture, Microsoft
Windows Filtering Platform, Microsoft
VMM DHCPv4 Server Switch Extension}
IovSupport : False
IovSupportReasons : {This network adapter does not support
SR-IOV.}
IsDeleted : False
Question:
Aside from a few of my favorite MS MVPs (shout out to
WorkingHardInIt for having this same question), I can't find much documentation on employing 2008 R2 NLB on guest VM within a fabric-oriented, VMM-built 2012 Hyper-Visor converged switch (no network virtualization...yet).
Yes I know all about VMM NLB but 1) I'm trying to wedge NLB in after building these VMs without a service template (NLB is the audible, essentially) and 2) MS NLB is configured in providers & I've created requisite VIP templates.
Even so, I ought to be able to create an NLB cluster without VMM's assistance in this scenario correct? Suboptimal, I know but possible, yes? Essentially I've put to synthetic NICs on each VM, set IPs manually, and assigned them to the same vlan. I can ping
each synthetic NIC, but not the cluster IP.
And yes: these particular vNICs have Mac Address Spoofing enabled.
Cisco:
I have a TAC case open with Cisco, but they can't quite figure it out either. IGMP Snooping enabled across the switch. And they insist that the old static arp entry to resolve this problem is no longer necessary, that Microsoft now complies with relevant
RFCs
Possible SOlution:
Only thing I can think of is flipping MulticastForwarding param below from disabled to enabled. Anybody ever tried it on a converged virtual switch on the Hyper visor? Is my virtual converged switch protecting
me from multicast igmp packets?
PS C:\utilities> Get-NetIPv4Protocol
DefaultHopLimit : 128
NeighborCacheLimit(Entries) : 1024
RouteCacheLimit(Entries) : 128
ReassemblyLimit(Bytes) : 1560173184
IcmpRedirects : Enabled
SourceRoutingBehavior : DontForward
DhcpMediaSense : Enabled
MediaSenseEventLog : Disabled
IGMPLevel : All
IGMPVersion : Version3
MulticastForwarding : Disabled
GroupForwardedFragments : Disabled
RandomizeIdentifiers : Enabled
AddressMaskReply : Disabled
Thanks for any thoughts.
Robert

Sorry for the poor follow-up Steven. We are using Server 2012 Hyper-V, not VMWare, on the hosts. You can close this but for the benefit of anyone who comes across it:
After working with Cisco, we decided not to implement multicast IGMP. Cisco says you still need to create a static ARP entry on the physical switch, though my cluster IP address & Microsoft NLB 2008 R2 were set up with igmp multicast, not multicast or
unicast. Here was his email:
Yes, we will need the static mapping for the NLB server in this case because the NLB mac address is multicast and the IP address is unicast. I was under the impression that even the server would be using IGMP but that’s not
the case. We won’t need to do the mapping for the nodes though if they use IGMP. To this end, following is the configuration that should make this work.rp 192.168.100.157
0100.5e7f.649d arpa
<u5:p></u5:p>
mac address-table static 0000.0000.649d vlan <> interface <> disable-snooping
ßThis is the switch interface where the NLB server is located<u5:p></u5:p>
interface vlan<>
<u5:p></u5:p>
ip pim sparse-dense-mode <- This is needed for the switch to elicit IGMP joins from the nodes<u5:p></u5:p>
end<u5:p></u5:p>
I don't think it got through to him that there was a virtual Layer 2/3 Hyper-V switch on top of 8 teamed GbE interfaces in LACP/hash. "Where the NLB server is located" = 1)a Cisco port-channel bound to one of six physical hosts; the NLB VM itself could be
on any of those port channels at any given time (We have a six node Hyper-V cluster).
Once I enabled pim I did see activity; but we killed this later as we realized we'd have to implement the same on 40+ managed routers globally
Anyway we further would have had to implement this across managed routers at 40 sites globally according to Cisco.
Robert

I'm new to photoshop and I want to convert an image file to a fabric file like .zfab or .fab...is this possible? I want the image to be in color and the images are .png. I am using windows 8

HI I am using software for fashion design called Marvelous Design . I want to import my fabric patterns which are .png image files but they have to be in .zfab or .fab format. can adobe convert these files into these extensions? If so, how do I do it? Thanks for any help!

This is from File extension FAB - Open .fab files :
The FAB file extension is associated with the Fabmaster software, or file format developed by the Electronic Source Company.
Fabmaster seems to be obsolete product that is not supported by its developers.
~~~~~~~~~~~~~~~
As for the software, did you mean Marvelous Designer?
~~~~~~~~~~~~~~~
For ALL file formats supported by Photoshop, see:
Photoshop Help | Supported file formats

Can't able to add update server to fabric in SCVMM 2012 R2

Hi,
I have one windows server 2012 R2 standard machine (update server) with WSUS, I have installed from server manager as server role. This update server machine is having the public IP without domain and it is a VM on one of my Hyper-V server. I would like
to add the update server to my SCVMM 2012 R2 environment. When I try to add the update server to the fabric, it can't seems to be add because its throwing the error like, "Error (410) Agent installation failed on update server. The RPC
server is unavailable."
Has anybody else have clue ?
Can anybody offer some help ?

Hi,
following link provides info on how to add untrusted Hyper-V hosts to VMM
http://technet.microsoft.com/en-us/library/gg610609.aspx
as it might help you adding an untrusted WSUS also (haven't tested it myself)
MCITP SA - MCP Active Directory - MCP Infrastructure - MCP Server Virtualization www.it101.eu

Can't Install CISCO Fabric manager in Windows 7 32 Bit.

Hello Folks,
Can some one let me know how to launch the Fabric manager installer in IE 8, I am using Windows 7 32 bit OS with IE 8.
I can't launch the Fabric manager installer in IE 8, your help much appriciated. thanks in advance.

Open DOS command prompt
\bin\java -Xms512m -Xmx512m -jar
example:
C:\Program Files\Java\jre1.5.0_11\bin\java -Xms512m -Xmx512m -jar c:\tmp\m9000-fm-5.0.7.jar

LS AppDomain Host Process, Failed to start Fabric Pool Manager.

Hi,
Today renewed the
Certificate in and the server will not start.
Can someone help me.
I've tried for several hours to fix it.
System
Provider
[ Name]
LS AppDomain Host Process
EventID
50006
[ Qualifiers]
50181
Level
2
Task
1029
Keywords
0x80000000000000
TimeCreated
[ SystemTime]
2015-02-21T22:57:29.000000000Z
EventRecordID
6508871
Channel
Lync Server
Computer
srvlync.itexpert.pl
Security
EventData
System.ApplicationException: Failed to start Fabric Pool Manager. at Microsoft.Rtc.AppDomainHost.Launcher.Initialize(String[] args) at Microsoft.Rtc.AppDomainHost.Launcher.Main(String[] args)
System
Provider
[ Name]
LS Server
EventID
12330
[ Qualifiers]
50152
Level
2
Task
1000
Keywords
0x80000000000000
TimeCreated
[ SystemTime]
2015-02-21T23:00:06.000000000Z
EventRecordID
6508872
Channel
Lync Server
Computer
srvlync.itexpert.pl
Security
EventData
C:\Program Files\Microsoft Lync Server 2013\Server\Core\RtcHost.exe
C3E8302D
The worker process failed to initialize itself in the maximum allowable time.

Hi,
It can be the issue with Windows Fabric service.
Please try to Repair the Window Fabric Component with the following steps:
1. Stop Lync Services
2. Remove Windows Fabric application
3. Don’t Restart
4. Install Windows Fabric (C:\Sources\WindowsFabric)
5. Restart Windows
6. Confirm Windows
Fabric Service starts
Then test the issue again.
Best Regards,
Eason Huang
Eason Huang
TechNet Community Support

Nexus 7000 Switch Fabric Redundancy with Fab-2 ?

Hi all,
I know that N7K did not have N+1 Switch Fabric redundancy. It is required to have all five SF modules to provide full throughput. Does this change with FAB-2 modules ? I mean with new modules, does N7K have N+1 SF redundancy ?
Thanks in advance.
Dumlu

The N+1 fabric redundancy will depend on the type of module.
If you are using M132 (80G) per slot and you have 3x FAB-1 (46G each), it will provide N+1.
The same story applies to FAB-2. If you are using the F1 series, and have 4x FAB-2, you have N+1. Of course, if you are using F2 series linecard and have all FAB-2 populated, you don't have N+1 because F2 is 480G and all 5 FAB-2 will give you 550G.
HTH,
jerry

'Not running in a hosted service or the Development Fabric' exception on deployed Worker role

We are getting this exception after a worker role has been operating fine in production for several weeks. Once this exception starts getting reported, it will keep getting it every time the worker role tries to access anything with the Diagnostics:
Not running in a hosted service or the Development Fabric
Note that the role is full trust, and as I mentioned this in in production on the Azure servers, NOT in debug. The worker role itself does some dynamic compilation, for which it needs to start a new AppDomain. It appears that the exception is
coming from the spawned AppDomain when it occurs. The exception itself is triggered on a simple Trace.TraceInformation call.
What could cause this?
What can we do to recover from this?

We are getting this exception after a worker role has been operating fine in production for several weeks. Once this exception starts getting reported, it will keep getting it every time the worker role tries to access anything with the Diagnostics:
Not running in a hosted service or the Development Fabric
Note that the role is full trust, and as I mentioned this in in production on the Azure servers, NOT in debug. The worker role itself does some dynamic compilation, for which it needs to start a new AppDomain. It appears that the exception is
coming from the spawned AppDomain when it occurs. The exception itself is triggered on a simple Trace.TraceInformation call.
What could cause this?
What can we do to recover from this?
Hi,
I have tested this situation in Windows Azure platform and i can not reproduce your exception message, my test code in follwoing MSDN samples and i deploy it in Production status.
The MSDN article (include Appdomain code snippets)
http://msdn.microsoft.com/en-us/library/system.appdomain.aspx .
Base on my understand, the "Not running in a hosted service or the Development Fabric" error message occur when Azure Emulator or Azure development fabirc, because you create a new appdomain in WorkRole, and it may cause permission errors, a similar
posts by my research:
https://social.msdn.microsoft.com/Forums/en-US/windowsazuretroubleshooting/thread/50987285-58ac-484e-b604-725fe01a3325
If you still have some problems, please inform me. Thank you.
Please mark the replies as answers if they help or unmark if not. If you have any feedback about my replies, please contact
[email protected]
Microsoft One Code Framework

Proximity sensor problem -- direct contact with fabric confuses it

On the Twom (and I'd guess the Onem), if the prox. sensor is covered and the phone is locked, it disables all of the phone's buttons until the prox. sensor is uncovered. This is a good thing, because it means the volume can't accidentally be changed in your pocket so long as the phone was locked before it went in your pocket.
Here's my problem: at any small distance, the prox. sensor works exactly as it should, whether facing skin, fabric, whatever. However, if the phone is brought into direct contact with certain fabrics (like denim on my jeans), the prox sensor fails to "see" this and all the buttons remain active. This means that in my pocket, where the phone is fully in contact with the fabric, it usually still lets the ringer volume change and the phone unlock.
Anyone else notice this behavior with their phone, or is it just mine?

you got it right. The sensor sends out a signal, a light, that you can see if you push any of the buttons with the phone locked in low light. My guess as to how it works is it sends out a low-frequency signal, perhaps infared/borderline red light, and if it is reflected back, it recognizes it as being 'covered'. Because it is low-frequency/low-power, it only will recieve the signal back from very short distances. True, most fabric won't block it. If you're wearing tight jeans/pants, then it does work if you put hte screen-side against your leg. But what i did was file down the volume keys anyways. They sit about half as high as they were originally, and now it is very hard for them to be accidentally changed, but they still can be pushed for the camera zoom, or volume change, when i want.

Desbloquear de fabrica.

Similar Messages

Maybe you are looking for