Designjet 130 paper feed issue

Paper coiled up caused a jam. I cleared the jam and reset the tabs and still get the images for a paper jam and here is the report from the printer.
Printer Latest Errors:
# 0 81.01.1 D.05.04 SM: 01 [tError (l/PaperCtrl.c : 0331)] 02-01-2011 Page# 1595
# 1 42.10 D.05.04 SM: 01 [tError (s/MotorPhys.c : 0046)] 02-01-2011 Page# 1595
# 2 81.01.1 D.05.04 SM: 01 [tError (l/PaperCtrl.c : 0331)] 02-01-2011 Page# 1595
# 3 86.11 D.05.04 SM: 01 [isp_mech (MechCommand.c : 0794)] 02-01-2011 Page# 1580
# 4 86.01 D.05.04 SM: 02 [tError (arriageCtrl.c : 0445)] 02-01-2011 Page# 1580
# 5 81.01.1 D.05.04 SM: 01 [tError (l/PaperCtrl.c : 0331)] 02-01-2011 Page# 1570
# 6 79.04 D.05.04 SM: 05 [tCLC (redosmon.c : 0199)] 02-01-2011 Page# 1570
# 7 81.01.1 D.05.04 SM: 02 [tError (l/PaperCtrl.c : 0331)] 01-31-2011 Page# 1566
# 8 79.04 D.05.04 SM: 06 [tRedSP (fsm.c : 0549)] 01-27-2011 Page# 1559
# 9 81.01.1 D.05.04 SM: 01 [tError (l/PaperCtrl.c : 0331)] 01-27-2011 Page# 1552

This forum is focused on consumer level products. For the Designjet you may have better results posting in the HP Enterprise Designjet forum here.
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

Similar Messages

HP officeJet all in one 6310 paper feed issues at input tray

what could be the cause of my HP officejet 6310 printer intermitantly grabbing multiple pieces of paper at the input tray?
I have been using the same paper for over a year or 2 with no issues up to the last few months. I have blown out any dust and tried to clean the rollers with alcohol to no avail. Is it a part worn or did I not clean the right part?
It seems to happen more often with less sheets in tray. any help would be appreciated.

Hi,
Here is a link to a document that covers paper feed issues on the OJ 6310. There's a video which shows some steps about what to do. Even though you have cleaned rollers the video may contain more information about cleaning other rollers that you may not have cleaned.
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02036357&tmp_task=solveCategory&lc=en&dlc=en&cc...
I hope that this helps solve your issue.
---- If my answer was helpful please click the Kudos star.
If your problem is solved please click the Accept as Solution button so other forum users can use the solution.---->
(I am an HP employee) I am not a expert on all our products, but I'll do my best to help you.

Paper Feed issue

HP 6500A Plus
Mac/ Lion
When setting up my printer I was printing some test pages and the paper feed seems to be acting very strange. There is a wrinkled path the lengh of my paper where the paper feeder moved the paper through the unit. Seems to have forced the paper through the machine and wher it touched the paper it made crumpled tracks.
Thanks in advance.

Hey Peggalope! Are you using the ADF(Automatic document feeder) by chance? If so check out this document: Paper Path Issues in the Automatic Document Feeder
If not then check out this article: Printer Paper Tears, Wrinkles, or is Damaged while Printing from the All-in-One This article is not specifically for your printer but is similar enough to fix your issue. Had you had a paper jam lately?
Thanks!
-Sean
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------

Z6100ps 42 inch plotter paper feed issue

I have a HP Z6100ps 42 inch printer which will feed 4-5 feet of paper onto the floor during its schedule printer maintenance cycle. The firmware is up-to-date and everything prints normally, but when I get into work each morning I have a pile of paper waitng for me to clean up. Has anyone else had this issue? Is there a cure?
Help!

This forum is focused on consumer level products. For the Designjet you may have better results posting in the HP Enterprise Designjet forum here.
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

LaserJet 2100 Paper Feed Issue

Our company has an HP LaserJet 2100 printer. The problem is every 10 pages or so, the paper will feed through crooked causing the print to be off center and the edge to become crinkled. I replaced the paper with a different ream and a different stock, verified there is no paper bits in the path by completely removing the Registration Assembly, etc. and cleaning the paper path.
My question is could this be due to the rollers? I would just go ahead and replace them but it is quite a process to obtain replacement parts and if this doesn't fix it, I have wasted a lot of peoples' time and money. Any information would be appreciated, thank you.

I am having the exact same issue. Did u ever get this figured out?

Paper feeding issue with G85

I have a G85 all in one.
It has started to print at an angle on the sheet.
Paper seems to feed ok, w/o jams.
Any thoughts?

Hi,
Did you find any particular Event ID for your issue?
To troubleshoot this issue, have you tried changing the default printer and printing from other programs such as Word or any other?
The issue which you are facing might occurs because the Microsoft XPS Document Converter (MXDC) determines the paper size by using the FormID value on the server. As you commented that you are using Easy print driver first you can find incorrect paper size
if RD Easy Print printer driver first is enabled.
To work around this issue, use the forms that are defined by the system when you print. The paper sizes for these forms match on the server and on the client computer. Additionally, a printer driver can rename these forms. Please refer below article for more
information.
The client printer may print the documents by using an incorrect paper size if the "Use Remote Desktop Easy Print printer driver first" policy is enabled
Apart from this providing link to understand RD Easy print in Windows 7 & Server 2008 R2.
Hope it helps!
Thanks.

D110a paper feed issues

My printer has had these issues since day one of purchase.
1) Often, paper simply won't feed.
2) When it does feed, it usually tries to feed the entire packet of paper in the tray.
I have little hope of a solution, considering I've had these issues since the first time I used the unit.
I'm chalking it up to having purchased a low quality item. However, if you've seen these problems before I'd like to hear
what you have to say about it.

Try this link and see if it helps.
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02017179&tmp_task=solveCategory&cc=us&dlc=en&la...
**Click the KUDOS star on the left to say 'Thanks'**
Please mark a reply "ACCEPTED AS SOLUTION" if it solved your problem, so others can find it.

Adobe InDesign CS5.5 Paper Feed Issue

Hi,
I am using InDesign CS 5.5 on Mac OS X Lion.
I can't print a document from InDesign using paper tray 2.
Within the same setting, I CAN print it from Adobe Acrobat X.
Has anyone got the same issue? know how to solve this issue?
Please leave a comment if you do so.
Thank you.
Bryan

Like I said, I don't know.
I never print from ID. If you feel it's a bug and needs to be reported you can do so here: https://www.adobe.com/cfusion/mmform/index.cfm?name=wishform
Bob

C4280 paper feed issues

Hello,
I have an HP C4280 Printer. Generally works pretty well, although recently, it does not feed paper properly. It picks up multiple sheets, which causes jams. If we feed in, and print, a single page at a time, it works fine. Is there a way to replace the feed roller in the back? Or is this likely to be something worse?
Thanks!

Try this link and see if it helps.
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02017179&tmp_task=solveCategory&cc=us&dlc=en&la...
**Click the KUDOS star on the left to say 'Thanks'**
Please mark a reply "ACCEPTED AS SOLUTION" if it solved your problem, so others can find it.

Designjet 1050c paper cutting issues

I have a designjet 1050c printer. The problem is it will not cut the paper at all. The carriage scrolls across as if it's wanting to cut the paper but it never does. I've adjusted the carriage properly and still no success. Any ideas or tips would be greatly appreciated.

HI
As your unit is considered a bussines unit, you will most likely get a better response HERE.
Say "Thanks" by clicking the Kudos Star in the post that helped you.
Although I work for HP my posts and replies are my own
Please mark the post that solves your problem as "Accepted Solution"

Officejet 5510 paper feed issue

The machine is giving a paper jam message when there is no paper jam. If I press OK or Cancel, the message goes away for a few seconds. Then, the unit on the right side which operates to move paper through starts up . Most of the time it does not pick up paper. Sometimes, it does pick up paper, moves it through partially, stops, then reverses the paper, stops, pulls it forward again, stops, reverses again, then stops and the paper jam message reappears. Anyone know what I can do about this?

The machine is giving a paper jam message when there is no paper jam. If I press OK or Cancel, the message goes away for a few seconds. Then, the unit on the right side which operates to move paper through starts up . Most of the time it does not pick up paper. Sometimes, it does pick up paper, moves it through partially, stops, then reverses the paper, stops, pulls it forward again, stops, reverses again, then stops and the paper jam message reappears. Anyone know what I can do about this?

Laserjet 1018 paper feed problem - started suddenly and now wrinkles paper but does not feed it in

This HP Laserjet 1018 is 4 years old, has worked flawlessly. But a day or two ago it fed a sheet of paper, there was a ripping sound, and the paper emerged, printed, but with a 1/4" wide, 5" long missing bit near the bottom, running the long way of the paper. I found and removed the crinkled up torn strip of paper, and have restarted this printer numerous times. Since that incident, it refuses to feed paper correctly, but bunches it up and wrinkles it a bit from the left to right and does not feed it in. Thus, won't work. I can't see any broken parts or anything stuck inside -- and taking this printer apart is v. complicated -- no easy panel to remove to see the feed mechanism. I'm doubtful I can take it apart enough, and still get it back together. I've cleaned the feed roller (small half-round gray rubber thing) and it does not seem to be the problem.
Questions:
a) anyone experienced, and solved this problem?
b) is it worth trying to send this for repair (I got it on special for $69, and the replacement equivalent now appears to be the HP P1102w, which is selling via Amazon for $94.99
Thanks

Hi. Thank you for your post.
The following link at the HP Customer Care web site may provide some help on the paper feed issues you are seeing.
http://h20000.www2.hp.com/bizsupport/TechSupport/SupportTaskIndex.jsp?lang=en&cc=us&taskId=110&prodS...
Although I am an HP employee, I am speaking for myself and not for HP.

Paper feed not working

Hello, Below are the sequence of events that happened and the problem I am facing: 1. I was able to use my HP 3510 printer print a page even 30 minutes ago. 2. After that, I tried scanning a page. The scanner got stuck many times. I opened the top lid of the printer and saw the scanner bar (I don't know how else to describe it) stuck in the middle. I restarted the printer and my computer and finally, after 6-7 retries, I was able to scan a page. Scanner has been working perfectly ever since. 3. After the scan was completed, I tried printing another page. The page feeder did not work. It showed me a "Out of paper. Load paper into the tray" message. I tried printing again by putting the page in more securely in the page feeder section but it showed the error again. I tried noticing what was happening and here is what I found out: a. The page was getting pulled into the printer. b. After the initial pull, the page stops once and the printer tries to pull in the paper again. But this time the paper gets pushed back out. When I look at the page, the top middle part (the end which was going into the printer first), is all crooked. ONLY the top middle part is crooked and the rest of the paper edge is the same. Every time I try to print a page, the same thing happens. The page is pulled in and then the print pushes it back the way the page came in and shows the "Out of paper" error. What can I do to fix this issue? Thanks.

Hi , Welcome to the HP Support Forums! I see you are running into some paper feed issues with your HP Deskjet 3510. Thank you for the detailed information. I would like you to go ahead and start troubleshooting here: HP Deskjet 3510 and HP Deskjet Ink Advantage 3510 e-All-in-One Printer Series - An 'Out of Paper' Error Message Displays on the Control Panel and the Printer Does Not Pick Up Paper Follow all steps listed above, focusing on the cleaning of the papers rollers. Let me know the outcome, I will watch for your reply. Thanks,

No paper feed Office Jet 6500 710a

The initial paper feed fails to load the paper, resulting in no paper error.
I tried all the steps HP suggests.
The problem started with a paper jam. All the paper seems to be removed.
The printer makes a sound of radars clicking.
With a litle help, pushing the paper in for some cm, the print is correct.

Hello @C4me,
Welcome to the HP Support Forums!
I understand that since removing a paper jam in your HP Officejet 6500A e-All-in-One Printer you have not been able to print as your product fails to grab paper in the paper tray and feed it into the unit. I would like to assist you today with this issue. Now you mentioned in your post that you have already ran through all of the troubleshooting steps for this particular issue and that the jammed paper seems to have been completely removed. There is chance that the initial jam that you had may have damaged the paper feed rollers. This would result in no paper feed at all and an 'out of paper' message, or you having to guide the paper into the machine for the rollers to actually grab the paper.
With that being said, can I please have you double check these two support documents to ensure that all steps have been completed:
'Out of Paper' Error Message and the Product Does Not Pick Up or Feed Paper
A 'Paper Jam' Error Displays on the HP Officejet 6500A and 6500A Plus e-All-in-One Printer Series
If all steps have been attempted to no avail, than I'm afraid that you would need a whole unit replacement to correct this issue. Should you want to explore additional options I suggest that you contact our Technical Support queue by phone.
HP Technical Support can be reached at: 800-474-6836.
If you live outside the US/Canada Region, please click the link below to get the support number for your region.
HP Worldwide Contact
Please let me know if any of the steps I've provided you resolve your paper feed issue. Best of luck!
X-23
I work on behalf of HP
Please click "Accept as Solution" if you feel my post solved your issue, it will help others find the solution.
Click the "Kudos, Thumbs Up" on the right to say "Thanks" for helping!

Paper feed

Hello Everyone,
I have a used HP 8000 printer and it won't pick up and feed paper.
I have cleaned the rollers , re booted the printer as instructed in Trouble shooting, ...
I 've also watched the pick up rollers as they come down, and they are moving into position,.but they will not pick up the paper.
Is there maybe an adjustment I might perform myself ?
Thank You ,
Kenneth
This question was solved.
View Solution.

Hello @Oldradio, and welcome to the HP Forums, I hope you enjoy your experience!
I see you are having paper feed issues. I would like to help!
I'd suggest starting by removing the ink cartridges, and performing a power reset on the printer. Disconnect the power cord from the printer and the power outlet, then wait 60 seconds. After 60 seconds, plug the printer back in. Ensure you plug the printer directly to a wall outlet. Make sure to bypass any sort of surge protector or power bar.
I would also suggest updating the printer firmware:
HP Officejet Pro Firmware
Good luck and please let me know the results of your troubleshooting steps. Thank you for posting on the HP Forums!
Please click “Accept as Solution " if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks" for helping!
Jamieson
I work on behalf of HP
"Remember, I'm pulling for you, we're all in this together!" - Red Green.

Designjet 130 paper feed issue

Similar Messages

Maybe you are looking for