Designjet 510 with lpt1 print server

Hi,  I just bought Designjet 510 42-in to replace my old plotter.  I cannot install IP at the plotter for using with LPT1 print server.  I dont want to buy new network card for the plotter since I already have LPT1 print server for my old HP750C.  Now my network cannot detect the plotter because I cannot install IP address.  The computer can detect the print server but not the IP address.  Pls anybody help me. Thanks

This forum is focused on consumer products, you may have better results asking your question in HP's Designjet Forum here.
Bob Headrick,  HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

Similar Messages

  • Printing with SMC4007ABR Print Server to PostScript Printer

    I've just set up my Mac Mini in a new network configuration, with an old SMC4007ABR router/print server printing to my Ricoh Laser AP2100 printer, using IPP printing and the configuration for a Generic PostScript printer, which had worked for this printer in previous setups. I am using the IP address of the router, 192.168.2.1, and the queue name specified in the documentation "lpt1". When I log into the router to view the status page it says the printer is idle and ready. When I submit a print job, I get the message "Network host '192.168.2.1' is busy; will retry in 30 seconds...".
    I have tried deleting the printer queue and recreating it, using the queue name with upper case, using the queue name specified for use with Windoze ("LP"), changing the router configuration from DHCP to manual IP assignments and back again, resetting the print system from the Printer Setup Utility, using the CUPS interface at http://localhost:631/ to modify the printer setup in any sane way I could think of. I have looked at anything I could find in this forum that seemed relevant, but haven't found anything to try which I haven't tried. I have tried the SMC technical support system, but the router is no longer supported by them, but by another firm which charges per incident, and doesn't support Macintosh.
    I would appreciate any suggestions from people who know idiosyncracies of this router, or who have fruitful insights into this strange behavior. Clearly my Mini sees the printer queue, but not well enough to be able to transmit data to it. Thanks for any insights you can offer.
    Regards,
    Geoff
    Mac Mini Intel   Mac OS X (10.4.8)  

    Thanks very much for your response. It seems I was ignoring the answer in some of the posts I was looking at, having misjudged that they were applying to a different sort of situation. I can't even remember what set of instructions from years ago established such a strong prejudice that I needed the IPP protocol. In any case, I'm grateful for your help.
    Best regards,
    Geoff
    Mac Mini Intel Mac OS X (10.4.8)

  • HP C309a set-up with wireless print server

    My HP C309a wireless radio no longer seems to work (run diagnostics, reset to factor defaults, etc, over and over without luck), so now I'm trying to set it up with a Linksys Wireless-G print server (WPS54G).  I've gone thru all of the linksys print server set-up steps, but the wireless connection fails.  I turned off the wireless radio on the printer, but are there other steps I need to take to get the wireless print server to work with this printer?  Thanks.

    Have you reset the printer - turn it off, hold # and 6 keys while turning back on.  This can sometimes reset the wireless radio....sometimes not.
    Honestly, I don't know a lot about wireless print servers other than they are hard to set up and its best if the server and your router are made by the same company - and that they usually only support printing.
    Another off the wall option is to use powerline Ethernet (google it).  This uses the power lines in your home to transmit Ethernet signals.
    Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
    I am employed by HP

  • HP psc 1315xi with wireless print server

    Printer = HP 1315xi, Wireless Print Server = Linksys WPSM54G.  Computer #1 = Windows Vista (64-bit), Computer #2 = iMac using OSX.
    I set up the Windows Vista computer on 198.162.1.101 using the HP 1300 driver listed in the setup.  I can only print one document and then printing fails.
    I set up the  OSX computer on 198.162.1.101 but couldn't find a listed driver that workes. Also, OSX give the ip address as 198.162.1.104.  I tried that with no success.
    The HP 1315xi works fine on both computers when connected directly via USB
    Any ideas on what to try next?
    Thanks,  Ira

    Update - I have gotten the printer to work under Parallels once I assigned it to an LPR queue. Still no progress on the Mac side

  • HP F4480 and setting up with a print server

    I have the F4480 all-in-one printer, home network using a router with two laptops, an HP with win 7 and an Acer netbook with XP. Currently, the printer is connected vis usb to the HP laptop. It can be inconvenient when either of both laptops is in use away from the computer desks and the HP is not connected to the printer, resulting in the printer being unavailable.
    So, how co i set up a print server or a new router with p/s capability? Is it possible or sensible to do such a thing?
    I am not all that geeky to solve a complicated install of either a p/s or another high-tech router. I have searched the net for answers, but am confused as to the feasibilty of the job or the hardware needed.
    Thanks for input.
    Barsac

    1. Does it come with software to configure it and modify it as needed with a PC?
    Yes
    2. Are these verions of the Extreme still sold, or are they considered obsolete?
    They are no longer sold.

  • Macbook Pro won't work with HP print server n2101?

    Hi all, happy New Year.  I have a new Macbook Pro and I am trying to hook it up to my HP print server n2101 and my HP psc 2210 all-in-one printer.  The mac recognises the server (and vice versa), the mac prints when connected directly to the printer but the server refuses to connect with the mac (keeps showing 'idle')  Anyone have any ideas how to fix it?  Very disappointed as all things mac usually work with no probs!

    Hi, I used the Mac setup instructions, not the PC ones.  The printer was automatically recognised in print and scan when I connected it with a USB cable.  I accessed the server's web-based page and followed all the instructions, but still no joy.  Thanks for the tip about posting.  I have just posted in the section you suggested, so let's see what happens.  From a quick scan around the apple forums, lost of other people seem to having precisely the same problem (and not just with HP printers!), but unfortunately, no-one seems to be offering a solution!  And trying to get through to the apple online support is a complete waste of time.  They've been 'not available' for two days now.  Christmas/New Year shutdown, I suppose.  Thanks for all your help, though!

  • C5550 non-compat​ibility with Netgear print server

    Netgear claims my HP Photosmart C5550 is in-compatible with their wireless PS121v2 print server.  What print servers are?

    Hi, Les,
    I think that info about Macs and postscript printers applies to OS 9.
    But there are usually two challenges to get this working:
    1. Driver - postscript drivers aren't limited to local connections; non-postscript drivers nearly always are (because manufacturers provided Carbon drivers that specify the comm type). A postscript PPD/driver for your model is included in OS X.
    2. Print Server setup. There's almost always an auto-setup wizard for Windows. We Mac users have to read the manual and understand what details to use in the Add printer dialog.
    First - what is called the TCP/IP protocol in the Netgear manual is the LPD protocol on OS X. What is called the Physical Port Name in the manual is equal to queue name in OS X. If I'm reading the correct manual, the queue name for parallel port 1 is "P1." Enter that in the space for queue name in the Add printer dialog.
    Good luck.

  • Wireless Printing with Netgear Print Server and HP Officejet 6110

    Setting up my wife's iMac for wireless printing (Mac is in Kitchen, printer in home office).
    We have a Netgear router and her internet connection (wireless) is fine.
    I configured the WGPS606 via a Vista laptop and have effectively printed through to the server wirelessly from the laptop.
    I downloaded and installed the drivers for the HP printer to the mac and have successfully printed when connected via USB (brought the printer to the kitchen to test)
    In adding the IP printer, I am able to set up an IP printer fine, but the HP driver does not appear in the dropdown menu.
    I have been able to get the iMac to ping the Print Server and choosing another HP driver does spool, but with gibberish of course.
    I believe the problem is that I can't figure out how to get the new driver to appear in the dropdown in the printer settings, which should solve the problem, I think.
    Advice?
    Thank you.
    Message was edited by: Tauria

    Unfortunately, there are two kinds of driver on OS X (not like Windows), Carbon and CUPS. To use the CUPS standard network protocols like IP printing, you have to use CUPS drivers. HP doesn't provide CUPS drivers (yet). Install the hpijs 3-part set:
    http://www.linux-foundation.org/en/OpenPrinting/macosx

  • HP Director won't work with Wireless Print Server

    I have an HP 5500 Office Jet all in one.  It comes with bundled software called HP Director that enables scanning, printing, and faxing.  The software worked fine while I had the printer connected to my pc with a USB cable.
    To give myself flexibility I installed a WPSM54G Linksys Wireless G Printserver.  There is no direct connection between my printer and pc anymore.
    Printing still works fine.  This is being handled by the Linksys software.
    The HP Director no longer can find the printer.  When I try to scan (for example) using HP Director, I get a message that "an error occurred communicating with the printing device...".  It presumably is looking for a direct USB connection, and not finding one.
    I can't find a fix on the HP site, but I imagine there must be one.  Wireless print servers have been around for quite a while.  Is there a download that will solve this problem?
    Thanks for your help.

    Hi JoJoh,
    I can't be of much help with the printer but I just checked my "Pages" and my version number is 4.0.2. I'm using iWork 09. Perhaps you need to update? I just checked the "Snow Leopard Compatible" site and found "Apple Pages 4.0.2" is compatible. It didn't mention 1.0.2. I'm so sorry. That's pretty rough when it's how you make your living.
    As for the printer, I have an HP Photosmart C4580 which wouldn't print. I finally just deleted all the printers on my MacBook and used my Snow Leopard install disk and selected the "Optional Install" which allowed me to just reinstall the printers. My HP is now working fine. I do feel like this is just a work-around until HP gets things sorted out. I say that because even though my HP now works, the only place it shows up is in my users folder. It's not in my Applications folder, but as long as it works for now, I don't care.
    Hope I was of some help to you. Best of luck!

  • Mac Printing with a printer server and Windows XP desktop

    I have the following configuration:
    Dell Desktop running XP
    Apple iBook G4 running 10.4
    Linksys Router
    Linksys Print Server
    I can't get my iBook to print through the print server. I have tried IP Printing and provided the printer server IP Address and correct printer driver "HP LaserJet 1012 Foomatic/hpijs (which I think is now part of 10.4). When I try to print I get the following message, "Printer Busy; will retry in 10 sec. I have also had Connecting to 192.168.1.78 on port 630... and nothing happens.
    Any suggestions? I am at wits end because nothing is working. I know that my wireless router and print server are working because I ping'd them from the PC.
    Any help would be greatly appreciated.

    On windows, the setup software fills in required info like print server queue name - but we don't have that software on the Mac.
    Look in the print server manual and check the supported protocols - LPD and IPP require a queue name which you can find in the manual. HP Jetdirect protocol doesn't need a queue name, and is called TCP/IP raw or socket 9100 printing in some manuals.
    Good luck.

  • Unable to print to kyocera fs-1020D with netgear printer server

    Hi,
    I have a Kyocera FS-1020D connected to the network via a netgear PS101 printer server. I can see the print server admin page through my browser. I have installed the correct printer driver for the fs-1020d. Every time I try to print to the printer, it pauses and I can restart the printer but when I try to resume the document the printer pauses again.
    Thanks for any help.

    This topic has been covered several hundred times. Please search for "CUPS print server."

  • How to connect Canon MP470 with USR5461 Print Server on Leopard 10.5

    The main problem I had with adding this printer is that the drivers from Canon's website do not work. Do not download and use the CUPS driver provided from Canon.
    You need to use this driver which should be included on your MacBook: Canon PIXMA MP150 - Gutenprint v5.1.3
    Here are the steps:
    1) Go to System Preferences
    2) Click on Print & Fax
    3) Hold down alt/option next to control and click the + sign to add a printer.
    4) Select advanced from the tabs above. Note: If you do not see an advanced icon on the top toolbar, right click and click customize toolbar to add the advanced button (the fact that you have to do that is weird to me).
    5) Wait for a little while when you enter into advanced and it will eventually give you a list of printing protocol types. Select the drop down labelled types and select Internet Printing Protocol (http)
    6) Enter the URI http://192.168.2.1:1631/printers/My_Printer
    7) If you changed your router address replace 192.168.2.1 with whatever address you use to access your router's settings page.
    8) Select the driver Canon PIXMA MP150 - Gutenprint v5.1.3
    9) You may enter the location of your printer if you want i.e. Brad's Room or where ever your printer is located.
    10) Click add printer.
    11) You should be back to the Printer & Fax screen. Double click the newly added printer on the list to your left. That will open the printer queue.
    12) Then select Printer from the system menu on top and select print test page.
    13) Make sure your printer is on and everything is connected.
    14) Happy printing.

    Actually there is a better way. I had been having problems on my new Macbook with OSX 10.5 but not on my Mac Mini running OSX 10.4. After doing some searching I figured out that it had something to do with the way 10.5 handles CUPS whatever that is. After sitting on hold with Apple forever they blamed it on USR even though my other Mac running 10.4 and my Windows machines all work fine.
    Since Apple refuses to admit it is there problem here is the work around I came up with. It is a two parter. Before you start make sure your printer driver is installed just like you would if your printer was connect directly to your Mac.
    First Part
    1) Open the "printer and fax" control panel
    2) Delete the old printer set up through the USR5461
    3) Click the "+" sign to add a new printer
    4) Here is the tricky part apple doesn't tell you. You need to go into "advanced set up but there is no obvious way to do that. Right click on the blank spot next to more printers and select "customize tool bar".
    5) Click and drag the sprocket called "Advanced" to the tool bar"
    6) Then click the "advanced" icon in the tool bar.
    7) Give it a few seconds before clicking anything. Then in the "type" drop down menu choose "internet printing protocol (http)"
    8) Enter the IP address of your printer (the default for the USR5461 is http://192.168.2.1:1631/printers/My_Printer)
    9) Name the printer and fill in the location field with whatever you like
    10) From the drop down menu choose "select a printer to use" and then find your printer driver.
    11) Then hit the "add" button at the bottom and you are done with the first part
    Second Part
    1) Use your browser to go to http://192.168.2.1/device.asp (this may require you to log into your USR5461)
    2) About halfway down you will see "Check the U.S. Robotics Web site for an update." and click the link
    3) The link takes you to a page where you have to select your device (USR5461 under "wireless")
    4) There you can find a "beta firmware update 3.93.35.0.9 (Jun 5 2008)", download that.
    Then go back to http://192.168.2.1/device.asp and upload the firmware file and choose "ugrade"
    5) Once you do this it will take about 30-60 seconds for your USR5461 to come back online. Wait until it is completely rebooted and check the firmware to make sure the update is correct. If so you are done with the second part.
    Now try printing. I hope this works for everyone.
    Well, to get the Advanced tab choice, I had to customize the Add Printer toolbar: there you can add a handy Advanced button. Press that, and there you'll find the Tiger functionality hiding!

  • Connecting a Photosmart C3180 with a USB cable to a wireless iomega iConnect with a print server

    The printer is recognized by all my software - Word, Excel, Adobe, etc. and will print when selected.  However, the HP Solution Center doesn't see the all-in-one at all, so there is no ink level check and no scanning function unless I unplug the cable from the iConnect and put it directly on my computer.
    Computer is  a Dell Studio running Windows 7 Professional 64-bit.
    Any suggestions?
    thanks
    liz

    Hi there billham68 and welcome to the HP Consumer printer Forums.
    Here is a link that should assist you in accomplishing the task at hand.
    Installing the Printer Software in Windows for a USB Cable Connection
    http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02458337&tmp_task=setupCategory&cc=us&dlc=en&la...
    If I have helped in any way, just click the Kudos star on the left. Also, if your issue has been resolved, don't forget to select Accept as Solution

  • Issues with 64 bit win 7 clients printing from 2008 R2 print server

    Hello All,
      I have a Windows 2008 R2 SP1 64 bit server built with a print server role. My issue is  64 bit win 7 clients cannot add a new printer. The clients see the printer in the list, starts the printer installation, get to the point of downloading the
    driver & then fails ' Windows cannot connect to the printer. ' the error is 0x0000012 or 0x000003ee. Any way I try to add the new printer I get the same result. The only way I can get the printer added is to do a local printer with the full path \\servername\printer_name
    and then "have disk" and point to the driver folder on the print server to get the printer added.
    Anyone have any thoughts on why the 64 bit clients will not add a new printer from a 64 bit print server ?
    Thanks,
    Steve

    Hi Steve,
    Please check if you can ping the print server successfully from this Windows 7 client computer. Did you encounter
    the same issue when add other printers? Or just for this one printer?
    Please type
    regedit on Run to open Registry Editor and follow the path:
    HKEY_CURRENT_USER\Printers\Connections and check if there has existent printer connection on the registry key.
    If any update, please feel free to let me know.
    Hope this helps.
    Best regards,
    Justin Gu
    Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

  • Deskjet D4260 does not work with an ethernet printer server

    I am attempting to attach a Deskjet D4260 printer to a home ethernet network using a StarTech PM1115U printer server. The printer has been connected to the network through a desktop computer, and worked perfectly.  The printer server will also work with a different printer (Canon i550).  However, it doesn't work with the D4260.  The server's port will not go online, and it does not appear to recognize the printer.
    This occurs regardless of OS (Windows XP, VIsta, 7, and 8 preview all don't  work).
    StarTech says there is no incompatibility issue with the server and host-based LIDL printers in general or the D4260 in particular.  Does anyone know of any issues, or how to get the D4260 to work with this printer server?

    Yes, that is how the instructions with the server tell you to install it.  The server is connected to the network via ethernet cable and the printer to the server via USB.  The server's instructions (as well as those given to me from StarTech support) say to install the printer as a local printer using a TCP/IP port using the server's IP address, which must be on the same subnet as the computer you are installing the printer on.  All this I have done.  There are a number of settings for the port.  It can be raw or LPR and there are other options.  I have attached it as instructed, and I have tried both raw and LPR, and tried various other settings.  I was able to install a Canon i550 on the server with no difficulties.  I was able to print to the printer, and the server, when I accessed it using either StarTech's server management software or a browser pointed to the IP address, showed the server's port on line and identified correctly the printer attached to it.  When I attach the D4260, however, it shows the port off line and does not identify the printer.  I got this server as a replacement for one that I bought without knowing that, according to its own documentation, it does not work with LIDL orinters.   StarTech did not have any such warning, and the StarTech support people said that there should be no problem with a LIDL printer.  They told me to consult HP support (to which this forum is the closest thing I can find).  It looks to me as if either there is something about the printer that needs to be reset, or the server does not work with this printer.  So far changing the driver does something, but not enough to print.

Maybe you are looking for