Deskjet 3520 wireless network password not accepted but it is the correct password

I just got this Deskjet 3520 printer and it's supposed to use my wireless connection. I got as far as it selecting the correct wireless network and the correct password was already there but after configuring a few minutes, it said the wireless network rejected the password. This happened a few times and I tried both the wireless network key and the system password. So I don't have a wireless printer at this point. I hope someone can help. thanks.

Hi mwell10,
I suspect you would have to either call your router provider or you can go into the EWS (Embedded Web Server) of the router using its IP address.
To get the IP address of the router you can click on the airport/wifi icon on the top right of the Mac screen ans select *Open Network Preferences*. Then in the Network Preferences you will see the Router IP address.
Take this IP address and put it into the address bar of a Safari browser.
Use the Thread below for further assistance.
http://community.linksys.com/t5/forums/forumtopicprintpage/board-id/Wireless_Routers/message-id/2171...
Hope this helps
Please click the Thumbs up icon below to thank me for responding.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Sunshyn2005 - I work on behalf of HP

Similar Messages

Hi. My new generation iPad will not accept my wireless network password.

Hi! My new generation iPad tells me my wireless network password is incorrect. Therefore, I cannot connect! Please help!

Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
Additional things to try.
Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Change the channel on your wireless router. Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
 Cheers, Tom

My machbook pro has suddenly stopped syncing with icloud. I am giving password of my apple ID but its not accepting. but by the same ID and pass i can open my icould in browser.

my machbook pro has suddenly stopped syncing with icloud. I am giving password of my apple ID but its not accepting. but by the same ID and pass i can open my icould in browser.

Another user just has a similar issue tonight and I advised him to go to the below Apple support link to see if the password was recognized there, which eventually resolved his username/passowrd issue. Give it a try and see if it works.
https://daw.apple.com/cgi-bin/WebObjects/DSAuthWeb.woa/wa/classicLogin?appIdKey= 58ef9db8ff4d201409e7270a68e4408ae1678e1618204c476572a1b5e5fb3518&path&language=U S-EN

Have a 802.11n time capsule, the range of the wireless network has shrunk down to nothing over last few days. Used to be able to use wireless network anywhere in house, but now can only use in my office. Will not connect to iphones, ipad, itouch, or noteb

Have a 802.11n time capsule, the range of the wireless network has shrunk down to nothing over last few days. Used to be able to use wireless network anywhere in house, but now can only use in my office. Will not connect to iphones, ipad, itouch, or notebook. Worked fine last week, but over weekend just started having issues.

It is very possible that you may have some form of Wi-Fi interference that has appeared recently that is preventing your Time Capsule (TC) from providing a clean RF signal.
I suggest you perform a simple site survey, using utilities like iStumbler, or AirRadar to determine potential areas of interference, and then, try to either eliminate or significantly reduce them where possible. Look for other Wi-Fis that may be operating nearby. Note those with the strongest signals and which channels they are operating on ... then change the channel used by the TC to be at least 3-5 channels away.

Hi, I am trying to print to an HP4050n via a secure wireless network. It prints but the default page setting sent to the printer is JIS B5. I have to hit the "Go" to get the printer to print. I have the correct setting in my Printer Settings (Letter).

I am attempting to print via a wireless (secure) network to an HP4050n printer. The document prints AFTER I choose "GO" on the printer. It is waiting as it wants me to load the JIS B5 paper/tray. I have the printer defined as Letter but in spite of that, it is requesting a different setting. I am thinking that because I am using the Generic PCL setting (I also tried the HP 4/5 PCL ) it is not communicating correctly. It does print once I get up and hit the GO button.
Any ideas? Thanks.

The paper size would normally be coming from the application rather than some setting in the driver. I've never seen the Generic PCL driver send a request for B5, but then I do use A4 rather than Letter and I don't have a PCL printer at home to check this. But I do think it has more to do with the application/document being printed.
For the application that you are using, is there are a separate Page Setup menu?
If the page and document is correctly set to Letter, you mention a wireless secure. If you mean something more than a wireless network that requires a password to access it, such as using https to connect to a remote server, then it could be settings for the shared printer queue. Although these shared printers are usually just an access point (throughport) for the remote client. Still, if you do have some additional network server for this secure wireless network, then this could be contributing to the incorrect paper size call.

HT3728 How do I reset wireless network password?

How do I reset wireless network password? Current password not being accepted; keep receiving connection timeout message.

http://support.apple.com/kb/ht3728

Deskjet 3050A - wireless radio is not functioning

I cannot connect my Deskjet 3050A-J611g on my wireless network. In attempting to set up the network I get the message: "The wireless radio is not functioning. Contact HP support". The troubleshooting information does not appear to address this problem

ATTENTION The wireless radio is not functioning. Contact HP support
diagnostic results
>wireless
                          --wireless on                                                                                 pass
                          --wireless working                                                                fail
                          --signal quality                                                                              not run
>connectivity
                          --connected                                                                                    not run
                          --disconnect count total                                                              74
                          --disconnect count (last hour)                                                    0
                          --disconnect count (last 24 hours)                                            0
>network
                          --network name (SSID) found                                                     not run
                          --other networks detected matching your networks name no
                          --wireless networks detected                                                        0
>settings
                          --printer settings consistent with wireless router settings not run
                          --no filtering                                                                                      not run
                          --channel                                                                                            not run
                          --security                                                                                           not run

HT2497 I just purchased the 2TB TC and set it up on bridge mode to my att verse which is connected via ethernet cable. The TC is continually blinking amber and an error message states that a wireless network cannot be found but the uverse is functioning

I just purchased the 2TB TC and set it up on bridge mode to my att verse which is connected via ethernet cable. The TC is continually blinking amber and an error message states that a wireless network cannot be found but the uverse is functioning great. The network name I assigned to the TC is also not appearing among available networks. How do I remedy this, please?

What OS on the computer you are using to setup the TC?
Did you turn on ipv6 for wireless to link-local... this is essential for network access now??
Try power cycling the network.. start up in correct order.. uverse.. 2min wait.. TC.. 2min wait.. computer.
No luck factory reset and start over. Use ethernet cable as well to the computer to help it.
No luck I can show you manual method.

Wrt610n wireless network does not work after firmeware upgrade

Hi
I just updated my Wrt610n hardware version 1 to the newest firmware, it did finish with sucess, I did factory reset reboot and reconfig. But the wireless network does not work , cant connect computers to it. Did downgrade the firmware to the same it was and restore my settings but still wireless does not work. But router works fine with lan. Any suggestions? maybe the firmware tosted the router?
Regards
Stefan

Update -
After last reset and reupgrade with the newest firmware for hardware version 1 I could config the router and connect 2 computers with wireless - but only for about 15 mín - then they lost connection and could not reconnect.
I did then get the newest update for hardeware version 2 - just to try and upgraded with that and got success, and now I have reset the router again and config it and those 2 computers are connected and have been for 1 hour now. So seems to be working - is it okay to have the firmware for hardware version 2 on my version 1 router?
Any thought what is going on - could it be that the other firmware had not loaded compleytle or?

Photosmart C6180 on wireless network does not respond when attempting to print

Photosmart C6180 successfully installed on wireless network does not respond when attempting to print. All in one is successfully installed on wireless network and SW successfully installed on Windows XP computer yet printer does not print. Get no error message other than document failed to print. HELP!

So gald I'm not the only one. I have been fighting this crappy HP printer for MONTHS also. Everything says a OK goody goody but printer fails to print every two to three weeks.

Wireless network does not automatically reconnect after sleep

I have a Belkin wireless G+ mimo modem router network. When I wake the mac from sleep it does not automatically reconnect to my wireless network and i have to manually select the network from the airport icon in the menu bar and then it connects without having to reenter my secure password. How do i set the mac to auto connect to the network after sleep? There are about 6 other wireless networks in range which may be effecting this reconnection.

In may case the network was already at the top of the preferred networks list.
Based of of a hint over at MacOSXhints.com, here's how I fixed this problem:
1. In the Network references pane, delete the Airport connection that does not like to reconnect.
2. Click Apply and Quit the System Prefs app.
3. Put the computer to sleep.
4. Wake the computer.
5. Go back in to the Network pref pane and re-add the Airport connection. Do not try to connect to the network at this time.
6. Click Apply and Quit the System Prefs app.
7. Use the Airport menubar app to connect to your network.
8. Verify connectivity
9. Put the computer to sleep.
10. Wake the computer.
11. Verify connectivity
My machine now consistently reconnects when coming out of sleep or restarting.
God luck!

What would cause an IMAC to recognize one printer on a wireless network and not recognize another printer?

What would cause an IMAC to recognize one printer on a wireless network and not another printer? I have a smaller HP and a an HP 4600. The computer recognizes the smaller printer but not the bigger printer even though the printer in Settings and shows up on Settings, but I cannot print to it.

Do you have a printer driver installed for it? When you open the Print dialog have you selected it from the Printer dropdown menu at the top of the dialog?
Do you know that the printer is working and is properly installed (Added?)

HT5022 I'm trying to add a "new client" to my wireless network using Airport Utility, but I can't find that option in the new version. I've downloaded all available updates of the OS and the utility.. Help!

I'm trying to add my HP wireless printer as a "new client" to my wireless network using Airport Utility, but I can't find that option in the new version. I've downloaded all available updates of the OS and the utility.. Help!

Why would you need to ADD a new Client. Unless the APE sytem is completely different then any other Wireless router the printer should get an IP address from the router. That is IF the printer is setup to get an IP from the LAN DHCP server.
Now you may want to make that IP it does get a Staticly assign IP address so it never changes, which will screw up printing if it does change. But i don't know if you can do that with APE routers.

Wireless network connection not showing up in network connections

Hi, Experts,
I recently re-image my Toshiba laptop (using window xp installation disk) due to I deleted few system files accidentally and can not boot the system up.
Before I re-image, I have no problem to connect Fios internet. After the re-image, the wireless network connection not showing up in network connections, so I cannot set up my Fios internet.
How to set up the wireless network connection that it will show up in network connections? Thank you very much for your help.

Issue Resolved. I did not turn on the wireless switch.

After my friend locked me out of my iPhone with too many wrong passwords I restored my iPhone and now it is showing that picture of a cable leading towards itunes and itunes says the sim is not supported but it is the original sim. How do I fix this?

After my friend locked me out of my iPhone with too many wrong password attempts I restored my iPhone via recovery mode and now it is showing that picture of a cable leading towards itunes, and itunes says the sim is not supported but it is the original sim. How do I fix this?

Something went wrong with the update, this can and does happen with every version of iOS.
There is nothing wrong with the update.
Simply restore the device via iTunes on the computer.
If iTunes is stating it will take hours to update, that indicates an extremely slow Internet connection and is likely the reason the OTA update failed.

Deskjet 3520 wireless network password not accepted but it is the correct password

Similar Messages

Maybe you are looking for