Deskjet F4272 need WIA driver

I've had no problem using my all-in-one for several years until yesterday. I try to scan a document and it tells me I need a WIA driver. I've downloaded the lastest version of the drivers for this model, and it still doesn't work, still get the same message.
Where can I get this driver, please?
This question was solved.
View Solution.

Hi,
Download and run HP Print and Scan Dr utility from link below to troubleshoot the issue.
www.hp.com/go/tools
Although I am an HP employee, I am speaking for myself and not for HP.
--Say "Thanks" by clicking the Kudos Star in the post that helped you.
--Please mark the post that solves your problem as "Accepted Solution"

Similar Messages

WIA DRIVER for HP 915

Need WIA Driver for HP 915 All in One Printer..

Hi Kedar31,
I understand you are looking for the WIA driver.
Windows Image Acquisition (WIA; sometimes also called Windows Imaging Architecture) is a proprietary Microsoft driver model and application programming interface (API) for Microsoft Windows Me and later Windows operating systems that enables graphics software to communicate with imaging hardware such as scanners, digital cameras and Digital Video-equipment. It was first introduced in 2000 as part of Windows Me, and continues to be the standard imaging device and API model through successive Windows versions. It is implemented as an on-demand service in Windows XP and later Windows operating systems
Resource: Wikipedia
The Shell Hardware Detection service runs as LocalSystem in a shared process. It shares an executable file with other services. If the Shell Hardware Detection fails to load or initialize, Windows 7 start up proceeds. No warning is displayed, but the error is recorded into the Event Log.
Dependencies
Shell Hardware Detection will not start, if the Remote Procedure Call (RPC) service is stopped or disabled.
If the Shell Hardware Detection is stopped, the Windows Image Acquisition (WIA) fails to start and initialize
Source: batcmd.com
To summarize, these services are necessary for scanning. Please complete the following steps to see if we can resolve the issue you are experiencing.
Hold down the Windows Logo key () on the keyboard and the 'R' to open the run box
Type services.msc and press Enter
Locate Windows Image Acquisition (WIA)
Right click and open Properties
Stop the service from the General tab and then Start it again
Verify that the Startup type is set to Automatic rather then manual
Also, look for 'Shell Hardware Detection' in the list of services. If it is not enabled/started, make sure to enable/start the service, and make sure the Startup Type set as Automatically from its properties.
Locate the 'Remote Procedure Call (RPC)' in the list of services. If it is not enabled/started, make sure to enable/start the service, and make sure the Startup Type set as Automatically as well.
If the issue persists, please use the HP Print and Scan Doctor. The HP Print and Scan Doctor is a free utility (tool) that helps to quickly resolve common printing, scanning and connectivity issues including but not limited to:
Connectivity :
USB: Verifies that the USB connection from your computer to the HP product is working correctly.
Network: Verifies that the network connection between your computer and your network is working correctly.
Device Status Test : Checks for device errors such as out of paper, paper jams, carriage stalls, and paper feed issues, and then provides instructions for fixing the error.
Driver Check : Checks for missing or corrupt driver files.
Device Manager : Checks for problems in Device Manager that would prevent printing.
Device Online : Checks if the product has been paused or set to offline, and then sets the status back to online if necessary.
Print Queue : Checks for and clears pending print jobs in the print queue (a log of print jobs waiting to print).
Port Match : Checks the port settings for the HP product.
Device Conflicts : Checks for conflicts with other drivers, such as other printer brands.
Ink Issues : Checks the cartridges and ink levels for issues that affect print quality.
Print Settings : Checks and adjusts the print quality settings.
Test Print : Prints a test page for print quality evaluation, and provides options for cleaning and aligning the printhead if necessary.
Scan Tests : Checks the scan mechanism, drivers, and registry entries.
You can also click the Printer menu to find the additional features such as cleaning printheads, aligning printheads, checking ink levels, and viewing advanced printer data for your selected printer.
Source: Try the HP Print and Scan Doctor for Windows
Click here to download and run the utility > HP Print and Scan Doctor
Please let me know the outcome of the tests performed, you will see a wrench, a yellow exclamation mark, a red X, or a check mark next each tested item. The tests performed depend on the version of software, the screenshot below is only an example, your PSDR scan test bmight look different.
I look forward to hearing from you. Knowing the outcome of the Print and Scan Doctor will help to point us in the right troubleshooting direction!
Please click the Thumbs up icon below to thank me for responding.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Sunshyn2005 - I work on behalf of HP

WIA driver needed for scanning

Hi there
I frequently use my Photosmart 2610 for scanning. Today, it has started giving me the error message "You need a WIA driver to use this device". Never had a problem in 18 months so why now? Where do I download the WIA driver?
Many thanks. CTodd

Hi CTodd,
Welcome to the HP Forums! I understand that you cannot scan with your HP Photosmart 2610. I am happy to help you with this issue! I have some questions for you:
What version of Windows are you using? Which Windows operating system am I running?
Can you make copies with the printer?
In the meantime, please try the HP Print and Scan Doctor.
Hope to hear back, and have a great day!
RnRMusicMan
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to say “Thanks” for helping!

WIA driver

Hi all, i have problem in my hp deskjet f735 all in one, when i wanna do scanning from toolbox on printer properties in my laptop, they ask for wia driver. Please help to solve this problem, i do need your advise on it, thank you

I m stil cant do scanning thru printer devise due to still ask for WIA driver, i download HP Solution Center and i can do scanning thru it, hope it can solve for this time. But still i wanna know about WIA driver and how to get it.

HP Deskjet F4272 - not responding

My printer (Deskjet F4272) is not responding when I send a document to be printed. The "resume" light is flashing and there is an "E" displayed on the printer but I have looked inside very thoroughly and can't find any obstructions. When I press the button next to this light, the printer will take a sheet of paper, make some loud mechanical noises, crumple it up a bit and spit it halfway out. That's all.
Also (I don't know if this is related or not), when the door on the right hand side of the printer is opened (the door used to take out and load cartridges) the printer cartridges do not travel over to the right hand side - they seem to be stuck over on the left.
Please help!

Hi juleslmt, and welcome to the HP Forums!
I see you are having printer issues. I would love to try and help you, but I do need a little information first. I am linking a few HP Support documents below that will show you how to find which operating system you are using. Also, if you're using Windows, please include whether your operating system is 32-bit or 64-bit. With this information we can provide you with accurate information.
Mac OS X: How Do I Find Which Mac OS X Version Is on My Computer?
Which Windows operating system am I running?
Is the Windows Version on My Computer 32-bit or 64-bit?
Also, do you have any error messages popping up when you try to print?
Good luck and please let me know the results of your findings. Thank you for posting on the HP Forums!
Please click “Accept as Solution " if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks" for helping!
Jamieson
I work on behalf of HP
"Remember, I'm pulling for you, we're all in this together!" - Red Green.

Need a driver for HP 895Cse for windows 7

I have an HP 895 Cse printer. Yes it is an old printer but supper dependable and don't want to have to buy another. I have a desktop that has Win7 Home Premium 64-bit on it and I can install this printer on there. It will not install itself so I need a driver. I can go to drivers on the HP site but there isn't one listed for this version of Win7. I don't understand why I can't find one because I have a laptop with Win7 with the same operation system and the printer work on it fine. I really would appreciate some help with this. Is there a way to find the drive on my laptop and copy it? Thanks

The driver is delivered through Windows Update. There are a few things to try: start with the document here (the Deskjet 895cse and cxi use the same driver). If that does not resolve the issue the driver install wizard available from http://www.hp.com/go/tools may resolve the issue.
If the above do not help then try the following: click Start, Devices and Printers, Add a Printer, local printer, LPt1: (as a placeholder), Next, Windows Update and wait for the list to repopulate (this may take a few minutes). Once the list reappears click HP (not Hewlett-Packard) for the manufacturer and select the HP Deskjet 895cse driver, Next, Cancel. At this point you should be able to connect the USB cable and have the system automatically install the driver on the proper post.
If all the above fail (not likely) then post the details back here along with any error messages. It is also possible to download the driver normally delivered through Windows Update from the Microsoft Catalog site, but the steps are rather involved and I would rather not write them up unless needed.
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

HP Deskjet Ink Advantage K209a Driver not found when installing windows 8

MY PRINTER " HP Deskjet Ink Advantage K209a" OPERATING SYSTEM Windows 8 32 bit
Driver not found when installing windows 8 .So,please give me a suggestion & give me new driver for win 8.
[Personal Information Removed]
Please give me a suggestion

Hey 101214,
I see you have a Windows 8 PC and a Deskjet Ink Advantage All-in-One printer (K209a). I also see that you need a driver link for this OS and Printer. Please follow the link below to download the driver for this printer/OS combo.
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=al-109242-1&cc=us&dlc=en&lc=en...
If you need information on how to perform the USB installation on your Windows 8 PC please click here.
I wish you the best!
Jason
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------
I am not an HP employee.

Need WIA Drivers

I just bought a new hp desktop with windows 7. I have tried installing my hp officejetd135 all in one printer and after much frustration I still find I need a WIA driver to proceed. Any assistance would be great!

I have the same situation. Did you ever figure this out?

WIA Driver Not Found

Whenever I want to scan papers from my Brother MFC-490CW Printer, it says: "You need a WIA Driver to use this device. Please install it from the installation CD or manufacturer's website and try again." I also just upgraded to Windows 10. Please help! Thank you.

Hi,This forum deals with HP products. As I can see on Brother's site, the printer currently not supported on Windows 10 according its compatibility information:http://support.brother.com/g/b/oslist.aspx?c=us&lang=en&prod=mfc490cw_all According the following list Windows 10 native drivers gonna become available for your printer in early December later this year, but the Windows 8.1 drivers are most likely to work on Windows 10:http://support.brother.com/g/s/id/os/windows.html#mfc You may try installing the Windows 8.1 drivers below:http://support.brother.com/g/b/downloadlist.aspx?c=us&lang=en&prod=mfc490cw_all&os=135 Best of luck,Shlomi

Im using HP laserjet M1120N MFP printer and its required WIA driver.

hi,
im using HP laserjet M1120N MFP printer.
last time i dont have any issues to printer or scan, and lately i cant scan
and only able to print out.
its required me have WIA driver. anyone know how to fix its.
thanks

Hello zuzack97,
I am sorry, but to get your issue more exposure, I would suggest posting it in the commercial forums, since this is a commercial product. You can do this at http://h30499.www3.hp.com/hpeb/
I hope this helps.
Regards,
Happytohelp01
Please click on the Thumbs Up on the right to say “Thanks” for helping!
Please click “Accept as Solution ” on the post that solves your issue to help others find the solution.
I work on behalf of HP

Need a Driver for a New HP Laptop. Driver is Not Available on This Site.

A customer of mine just bought two new HP Pavilion Dv7-1135nr. For some reason they each have different DVD drives. One works. The other one, says its DVD drive needs a driver. It has Vista, so I tried to update the driver via the web, and that didn't work. Then I came to this site to find it on the laptop's product page, and it's not there. Does anyone know where I could track this driver down?
Again, the computer is an HP Pavilion Dv7-1135nr. The drive in question is called: HL-DT-ST DVDRAM GSA I 50L ATA Device.
(As I said, the other, seemingly identical computer which has the exact same model number has a different drive. That drive is called: TS-L6332. It will not work in the computer that is having problems.)
Thanks in advance,
Vincent.

This file from Doug Knox's site will do the filter edit automatically without having to mess around in the Registry.It was originally
written for XP,but also works in Vista.
http://www.dougknox.com/xp/utils/XP_CD-DVD-Fix.zip
If this fails I would perform a complete System Recovery to reinstall Vista and drivers/software.Many times when a machine has problems
out of the box,a Recovery sorts it out.
http://tinyurl.com/2y4rub
******Clicking the Thumbs-Up button is a way to say -Thanks!.******
**Click Accept as Solution on a Reply that solves your issue to help others**

Need a driver for Acrobat Distiller 5.0.0.0 that will work on Win 7 Pro SP1 64-bit. How can I find it?

Need a driver for Acrobat Distiller 5.0.0.0 that will work on Win 7 Pro SP1 64-bit. Where can I find it, and what file is it? (Yes, it's an old Distiller that came with Acrobat 5. So shoot me. But I do need the driver.)
Win 7 prompted me for an *.inf file. Any idea?
If I find the original Acrobat 5 CD, which .inf would it be?
(Hey, since I'm asking, also a driver that will work on Win 8.1 Pro 64-bit.)
Thanks.

There is no .inf file on the Acrobat 5 CD that you can use to create a “driver.” If Distiller 5 even installs and runs on Windows 7 x64, the plumbing that came with Acrobat 5 to automatically feed PostScript files created by the PostScript driver to Distiller simply won't work with modern versions of Windows or any 64-bit version of Windows.
FWIW, Acrobat 5 is five full versions back from the current version. And no, we won't shoot you; you are effectively doing that to yourself! Your time must be worth something?!?!
- Dov

I want to use my canon pixma ip4500 as my printer with my good ole G4. I need a driver. Is there an easy way to get that or is my G4 too old?

I want to use my canon pixma ip4500 as my printer with my powerbook G4. I need a driver but was very confused with how to get one. Is it possible and could someone come down to my level and tell me step by step how to do it? Many thanks.

Nope, your PB is not too old.
Here is the link to the PIXMA ip4500 drivers on Canon's site:
Drivers & Software
The page has you first select your version of the Mac OS (10.4) from the pull-down "Chose Operating System" menu. Once selected, you'll see the available software, Click on the arrown next to "Drivers" and it should look like this:
(click image to enlarge if needed)
Click the word "Download " and you'll get the driver.
Note at the top of that image there are other links to other documents pertaining to this printer. If you click on "Brochures and Manuals," while you are on that web page, you'll have Canon's instructions, probably better done than by anyone here other than someone who has the same printer model on a Mac running OS 10.4.

I've installed bootcamp 4.0 on my iMac 27. Everything works superb, but for playing need for speed run or battlefield 3 I need catalyst driver 11.7 or higher. How can I update my graphics? Is there a possibility except waiting for a new bootcamp version?

I've installed bootcamp 4.0 on my iMac 27. Everything works superb, but for playing need for speed run or battlefield 3 I need catalyst driver 11.7 or higher. How can I update my graphics? Is there a possibility except waiting for a new bootcamp version?

But how do you install the drivers if Bootcamp is running interference?
Bottom line, I'ev tried to install three different versions of updated ATI driver sover the last few momnths and on each and every occassion have ended up with the original Bootcamp driver. A number of current games are unplayable on a Mac running Bootcamp as a result.
And if I can't run the software I want, then Bootcamp is as useless as boobs on a bull.

My ipod touch 4th gen works on itunes but not show on windows do i need a driver?

When first time i connect my ipod touch says that the driver for this hardware did not pass windows logo test so i did not installed, and now i need the driver so windows can use it as a storage device anybody knows where or how to get that driver back. helpppp.

iPod Touches do not have a disk mode. However, you can se the iPod in Windows explorer in order to move photos from the iPod to your computer. You probably need to reinstall iTunes and install the unsigned driver.

Deskjet F4272 need WIA driver

Similar Messages

Maybe you are looking for