Desktop 2 Needed to Print?

Hi:
I've just installed 10.4 on our PowerMac and now can't print from an OS 9 application. I get the following message?
"This printer cannot print as the Application is not AppleEvent aware and
you have not installed Desktop 2.0 software."
I'm not sure what the issue is nor where to go with this? The printers for this machine are the HP 2200 LaserJet and the HP 7210 OfficeJet.
Any help is appreciated....
jaseriek

This thread may help:
http://discussions.apple.com/thread.jspa?messageID=1514966&#1514966
But you can also use the LW 8 driver to print to your OS X queues:
http://docs.info.apple.com/article.html?path=Mac/10.4/en/mh660.html
Hope this helps.

Similar Messages

  • PDF document not full page but need to print it as a full page

    Hi,
    I have a pdf document which is 15 cm by 8 cm and need to print it as a full page without the white border making up the full page. How can I do this?
    The document was created in publisher and saved as a pdf.
    I am reading the document from Adobe Reader on a Windows XP machine.
    Thank you for any help any one can give.

    Do you have a printer that can print pages without a white border?
    Very few printers can do this.
    Aandi Inston

  • This is about iPhoto:  I need to print the FULL IMAGE as shown on the screen:  the image is SQUARE (equal on four sides).  iPhoto keeps cropping it into a rectangle - THIS IS NOT ACCEPTABLE!  How do I get what I see on the screen in print form???

    I need to print the FULL image as shown on the screen - the image is SQUARE (equal on all four sides).  iPhoto keeps cropping it into a rectangle - this is not acceptable!  How do I get what I see on the screen into print form?

    Like Terence explained:
    OT

  • Windows Server 2008R2 running Remote Desktop Services reports printer process does not exist when installing PDF printer

     Windows Server 2008R2 running Remote Desktop Services reports printer process does not exist when installing PDF printer, And when Installing network printers from the domain controller it reports it cannot connect to printer.  I can ping all
    network devices. I can connect to the internet.
    On boot I get a netlogon 5719 error followed by service control manager errors 7023,7001 and a group policy error 1129.
    Clients can connect to the remote application and RDP operates to connect to the server internally and externally.
    The domain controller is another server 2008r2 box. I have scoured the internet but have not found any solutions that work yet.

    Hi,
    After referring to your post, it can be identified that the issue which you are facing is mostly due to some network issue in your environment. Please recheck your network connection issue between computer and domain controller. 
    Can you able to ping with IP address and also with fully qualified name of a domain controller in the users' and computers' domain. If it fails states that name resolution issue with computer and domain controller. Are you using MS DHCP Relay agent then there’s
    available Hotfix for the particular Event ID. Please go through this KB 2459530 to fix the error event ID.
    As per the net logon error 5719 which you are facing states that the client component of Netlogon was unable to locate a DC for the domain it was trying to perform an operation against. Below is one of the reason. If this is being logged on a DC and the event
    refers to the DC's own domain, something might be preventing the client component of Netlogon from starting a network session (to itself or to another DC in the domain). The following event 7001 & 7023 states start & stop operation service. Please
    go through beneath article for more details.
    1.  Event ID 5719 is logged when you start a computer
    2.  Netlogon 5719 and the Disappearing Domain [Controller]
    3.  Event ID 1129 — Microsoft-Windows-GroupPolicy
    Hope it helps!
    Regards.

  • Need to print a report

    Hello guys,
    I have button in my form, which displays
    a report, I need to print the report,
    once the the button the pressed.
    Are there any ready made functions !!!
    A.Kishore
    null

    Kishore,
    Do you want the report to show up and then
    the browser print window to show up?
    If so, then in the unstructured template, call the window.print() method using the onLoad event for the body tag. When the report loads in the browser, you will get the browser print window (in Netscape). In IE, the print starts automatically.

  • HT4946 I need to print & back-up a series of abusive/threatening SMS (on iphone 5c) for my solicitor. Is there a way to do this which will show the time, date & sender info? How can I preserve (full) SMS data as evidence for future court proceedings?

    Does anyone know how to access sms text messages from iphone 5c backup from icloud or itunes? Apparently SMS can be restored so data I need must be stored in backup. I need to print a series of abusive/threatening SMS messages received on my iphone 5c from one sender. I need the time, date & whatever data is stored about source/sender of messages, as well as content. How can I access this data to create a chronological record of the abusive SMS messages and can I preserve the iphone's message log specifically-- so I can access records of these texts without having to restore a back-up? I need to do this to provide evidence for my solicitor and preserve that evidence for future court proceedings, thank you.

    http://www.wideanglesoftware.com/touchcopy/index.php?gclid=CMr1..
    http://www.ecamm.com/mac/phoneview/

  • I have a brochure I need to print. When viewed on screen it is pixelated, however when I change to presentation view it is fine. I need to print on presentation view. How do I do this?

    I have a brochure I need to print. When viewed on screen it is pixelated, however when I change to presentation view it is fine. I need to print on presentation view. How do I do this?

    Sounds to me more like you have the Display Performance set on Typical rather than High Quality Display. Unless there is a problem with a missing or out-of-date link, the display in ID has nothing to do with output quality -- all of the image data is used for output.

  • Need to print some text only in last page in SAP script

    Moved to correct forum by Moderator.  General wasn't right either.
    Hi All.
    I need to print "Remarks" only in last page of sap script.
    Can anyone please help me on this.
    Thanks
    Senthil kumar V.
    Edited by: Matt on Nov 21, 2008 7:38 AM

    Hi,
    you have 4 possibilities.2 at non main window, 2 at main window.
    at non main window.
    1. /: IF &PAGE(C)& = &SAPSCRIPT-FORMPAGES(C)&
    remarks
    remarks
    remarks
       /: ENDIF
    2, /: if &NEXTPAGE& ='0'.
    remarks
    remarks
    remarks
       /: ENDIF
    at main window
    3. Add the remarks at the last item of the main which is printed
    4. add a new item to your main (/E)
        put your remarks in it.
       Change your program in such a way this item will print as last one.
       like
        /E REMARKS
    remarks
    remarks
    remarks
       and in sapscript program add logic at the end.
    CALL FUNCTION 'WRITE_FORM'
    EXPORTING
    element = 'REMARKS'
    EXCEPTIONS
    element = 1
    window = 2.
    I am sure this will do. Make a choice.
    Gr., Frank

  • I need to able to print a pdf that is locked.  It has fields to fill in but then to save a copy I need to "print" to PDF not save as a pdf because that is not an option with the document.  Is there a way to do this?

    The PDF has fields to fill in but then to save a copy I need to "print" to PDF not save as a pdf because that is not an option with the document.  Is there a way to do this?  HELP!

    Sorry I thought  was just a one off, it would be no use for large volumes.
    Do you not have this avaiable in the print menu in Preview with these documents?
    I have also found a link on the Adobe web site that discusses that this facilty is enabled by the creater of the PDF.
    http://help.adobe.com/en_US/acrobat/X/pro/using/WS58a04a822e3e50102bd61510979419 5ff-7e0d.w.html
    If you do a web search there are various claims on how to save a protected PDF, I have'nt a way to test the proceedures. I would want a copy of any forms that I sent off, not sure why they protect them in this way, there must be a reason.

  • Multiple PR-PO but need to print GR based on PR

    Hi All,
    We have multiple PR grouped into one PO and when we receive Goods Receipts (GR) for this PO, is there any way we can print the goods receipt note based on PR ?
    I.e. Say 5 PR grouped into one PO and GR is posted and when we print the GR we need to print based on purchase requisition based, 5 print out.
    We have the requirement were we don't want to post GR individually.
    Appreciate if you can help me on this. Thanks.
    Regards
    Ashwin

    Hi,
    As and when we create PO with reference to PR.. I think you will be knowing the Item lines of the materials from which PR it is been taken.
    Then when creating a GR with respect to PO please enter the PO number with the line item number and then only the materials in that PR will be picked up while creating the GR.
    You can make a reference in one of the fields the PR number and then you can even customise in your forms for the print out of the PR number also
    Then you can configure for WE03 which is collective GR list and then when you print you will get the materials with respect to the PR only.
    Hope this is helpful,
    Thanks & Regards,
    Kiran V
    Edited by: Kiran. V on Apr 18, 2008 3:48 PM
    Edited by: Kiran. V on Apr 18, 2008 3:49 PM

  • Help needed in printing in java

    hello everyone, i m in grave need of a solution of printing a java page. I have a page designed in Java swings which contains mainly labels and textareas. And i need to print this page. The problem is that I have no clue how to go ahead. Cud neone arnd pls help me on this matter asap as this is very urgent. I shall be highly obliged to all the takers on this issue. Please email me at [email protected]
    Thanks and kind regards,
    Rahul.

    http://java.sun.com/docs/books/tutorial/2d/printing/index.html

  • I need to print the footer in all pages except last page.

    Hi,
    I'm working on PO RTF template. I got one probelm, I need to print the footer in all pages except last page.
    Can someone help me in this.
    Thanks in advance.
    Venki.

    This question has been answered already multiple times - please search the forum before posting a question - in case you did and you didn't find it - we added a feature
    in 5.6.2 to solve this problem - It is described in the user guide in the RTF template section search for start@last-page:
    Last Page Support
    XML Publisher now has the ability to show content only on the last page. This is useful for documents such as checks, invoices or purchase orders where you want want content such as the check or a summary in a specific place only on the last page.
    The basic command is:
    <?start@last-page:body?>
    <?end body?>
    http://forums.oracle.com/forums/search.jspa?threadID=&q=%40last-page&objID=f245&dateRange=last90days&userID=&numResults=15&rankBy=9
    Any content above or below these two tags will only appear on the last page of the document.
    Hope that helps,
    Klaus

  • Need to print simultaneously via the network/TCP/IP & also print parallel from stand-alone PC

    1. HP LaserJet 4200 Q2427A
    2. Win7 - 32bit
    3. When I print from the Networked PC (which is on same subnet as printer) Prints come out. No problems. Then I need to print from a PC( which is a standalone PC w/ no connection to the corporate LAN, but does have a separate DSL connection to the internet) connected via the parallel cable. Prints fine no problems. When I try to then go back to the networked PC and print, The job takes 10-15 minutes print if at all- which sometimes it does not print at all.
    4. The stand-alone PC was replaced with a new windows 7 PC. The previous stand-alone PC was running windows XP. We did not experience any issues when PC was XP. PC was replaced due to Hard drive going bad and age. The windows 7 PC has a PCI parallel card installed for the parallel connection.
    Have also tried using a parallel to usb adapter with same results.

    That would be Wireless Distribution System (WDS). That is to say Wireless to Wireless. And if I recall correctly that option is not available to you.
    Bridge Mode is bridging between ethernet and WiFi.
    One way you could maybe do what you want without ethernet over powerline adaptors is to get an Airport Express (more money), attach that to the Pirelli via ethernet. Put the Express into Bridge Mode. Now have the Express provide the WDS server to the Airport Extreme Base Station. Of course you now have 3 WiFi transmiters in your home just so you can print something, but just think of the coverage in your home.
    NOTE: If for some reason you decide to try this Express to AEBS WDS system, you can create a roaming network by giving all 3 WiFi systems the same SSID and password. When everyone is using the same SSID and password you can roam around the house and your laptops will automatically switch to the base station with the strongest signal (assuming that is worth something to you).

  • Need to print report imediately

    i need to print the report output immediately i am pasting some code which i am having problem , in job_open function module exporting parameters are gettting problem.
    CALL FUNCTION 'GET_PRINT_PARAMETERS'
            EXPORTING
              mode           = 'BATCH'
              report         = l_repid
            IMPORTING
              out_parameters = l_parms
              valid          = valid.
          IF valid <> space.
            CALL FUNCTION 'JOB_OPEN'
              EXPORTING
                jobname = my_job.
       SUBMIT l_repid VIA JOB 'MY_JOB' NUMBER jobcount TO SAP-SPOOL WITHOUT
       SPOOL DYNPRO SPOOL PARAMETERS l_parms.
            CALL FUNCTION 'JOB_CLOSE'.
          ENDIF.
    *Sending the print parameters to this.
          CALL FUNCTION 'GET_PRINT_PARAMETERS'
            EXPORTING
              destination    = 'LP01'
            IMPORTING
              out_parameters = l_parms
              valid          = valid.
          IF valid <> space.
            NEW-PAGE PRINT ON PARAMETERS l_parms.
          ENDIF.

    Hi!
    *Sending the print parameters to this.
    CALL FUNCTION 'GET_PRINT_PARAMETERS'
    EXPORTING
    destination = 'LP01'
    immediately = 'X'            "<<< add this line - immediate print
    NEW_LIST_ID = 'X'     "<<< add this line - new spool request
    IMPORTING
    out_parameters = l_parms
    valid = valid.
    Regards
    Tamá

  • I need to print logo in alv grid

    I need to print logo in alv grid .As of now its getting displayed but it cannot be printed .Kindly tell me wether there is any option to print it .Eitjer using ALV or Object oriented ALV.Please reply soon

    Hi Deepti,
    Refer the code below.
    report  sy-repid.
    type-pools : slis.
    *ALV Formatting tables /structures
    data: gt_fieldcat type slis_t_fieldcat_alv.
    data: gt_events type slis_t_event.
    data: gs_layout type slis_layout_alv.
    data: gt_page   type slis_t_listheader.
    data: gs_page type slis_listheader.
    data: v_repid like sy-repid.
    *ALV Formatting work area
    data: w_fieldcat type slis_fieldcat_alv.
    data: w_events type slis_alv_event.
    data: gt_bsid type table of bsid with header line.
    initialization.
      perform build_events.
      perform build_page_header.
    start-of-selection.
    *perform build_comment.     "top_of_page - in initialization at present
      select * from bsid into table gt_bsid up to 10 rows.
    *perform populate_for_fm using '1' '3' 'BUKRS' '8' 'GT_BSID' 'Whee'.
    *USING = Row, Column, Field name, display length, table name, heading
    *OR
      perform build_fieldcat.
      gs_layout-zebra = 'X'.
    *top of page event does not work without I_callback_program
      v_repid = sy-repid.
      call function 'REUSE_ALV_GRID_DISPLAY'
        exporting
          i_callback_program                = v_repid
          i_structure_name                  = 'BSID'
       i_background_id                   = 'ALV_BACKGROUND'
          i_grid_title                      = 'This is the grid title'
      I_GRID_SETTINGS                   =
          is_layout                         = gs_layout
          it_fieldcat                       = gt_fieldcat[]
          it_events                         = gt_events[]
        tables
          t_outtab                          = gt_bsid.
    Form..............:  populate_for_fm
    Description.......:  Populates fields for function module used in ALV
    form populate_for_fm using    p_row
                                        p_col
                                        p_fieldname
                                        p_len
                                        p_table
                                        p_desc.
      w_fieldcat-row_pos = p_row.          "Row Position
      w_fieldcat-col_pos = p_col.          "Column Position
      w_fieldcat-fieldname = p_fieldname.  "Field name
      w_fieldcat-outputlen = p_len.        "Column Lenth
      w_fieldcat-tabname = p_table.        "Table name
      w_fieldcat-reptext_ddic = p_desc.    "Field Description
      w_fieldcat-input = '1'.
      append w_fieldcat to gt_fieldcat.
      clear w_fieldcat.
    endform.                    " populate_for_fm
    *&      Form  build_events
    form build_events.
      data: ls_event type slis_alv_event.
      call function 'REUSE_ALV_EVENTS_GET'
           exporting
                i_list_type = 0
           importing
                et_events   = gt_events.
      read table gt_events with key name =  slis_ev_user_command
                               into ls_event.
      if sy-subrc = 0.
        move slis_ev_user_command to ls_event-form.
        append ls_event to gt_events.
      endif.
      read table gt_events with key name =  slis_ev_top_of_page
                               into ls_event.
      if sy-subrc = 0.
        move slis_ev_top_of_page to ls_event-form.
        append ls_event to gt_events.
      endif.
    endform.                    " build_events
    *&      Form  USER_COMMAND
    When user command is called it uses 2 parameters. The itab
    passed to the ALV is in whatever order it currently is on screen.
    Therefore, you can read table itab index rs_selfield-tabindex to get
    all data from the table. You can also check r_ucomm and code
    accordingly.
    form user_command using  r_ucomm      like sy-ucomm
                             rs_selfield type slis_selfield.
      read table gt_bsid index rs_selfield-tabindex.
    error checking etc.
      set parameter id 'KUN' field gt_bsid-kunnr.
      call transaction 'XD03' and skip first screen.
    endform.
    *&      Form  top_of_page
    Your own company logo can go here if it has been saved (OAOR)
    If the logo is larger than the size of the headings in gt_page,
    the window will not show full logo and will have a scroll bar. Thus,
    it is a good idea to have a standard ALV header if you are going to
    use logos in your top of page.
    form top_of_page.
      call function 'REUSE_ALV_COMMENTARY_WRITE'
           exporting
                it_list_commentary = gt_page
                i_logo             = 'ENJOYSAP_LOGO'.
    endform.
    *&      Form  build_fieldcat
    *Many and varied fields are available here. Have a look at documentation
    *for FM REUSE_ALV_LIST_DISPLAY and REUSE_ALV_FIELDCATALOG_MERGE
    form build_fieldcat.
      w_fieldcat-fieldname = 'BUDAT'.
      w_fieldcat-seltext_m = 'Dte pst'.
      w_fieldcat-ddictxt(1) = 'M'.
    Can change the position of fields if you do not want them in order
    of the DDIC or itab
    w_fieldcat-row_pos = '1'.
    w_fieldcat-col_pos = '10'.
      append w_fieldcat to gt_fieldcat.
      clear w_fieldcat.
    endform.                    " build_fieldcat
    *&      Form  build_page_header
          gt_page is used in top of page (ALV subroutine - NOT event)
          *H = Header, S = Selection, A = Action
    form build_page_header.
    For Headers, Key is not printed and is irrelevant. Will not cause
    a syntax error, but is not used.
      gs_page-typ = 'H'.
      gs_page-info = 'Header 1'.
      append gs_page to gt_page.
      gs_page-typ = 'H'.
      gs_page-info = 'Header 2'.
      append gs_page to gt_page.
    For Selections, the Key is printed (bold). It can be anything up to 20
    bytes. It gets printed in order of code here, not by key value.
      gs_page-typ = 'S'.
      gs_page-key = 'And the winner is:'.
      gs_page-info = 'Selection 1'.
      append gs_page to gt_page.
      gs_page-typ = 'S'.
      gs_page-key = 'Runner up:'.
      gs_page-info = 'Selection 2'.
      append gs_page to gt_page.
    For Action, Key is also irrelevant.
      gs_page-typ = 'A'.
      gs_page-info = 'Action goes here'.
      append gs_page to gt_page.
    endform.                    " build_page_header
    Settings for the Logo :
    01) GOTO - OAOR (Business Document Navigator)
    02) Give Class Name - PICTURES
    Class Type - OT
    Object type - whatever you want to call your area EG: OURCOMP.... then Execute
    03) Top left will say PICTURES. Bottom left will have multi tab. Select Create and double-click on Screen.
    04) Select your image from the appropriate directory.
    05) Give the image an appropriate name (not Screen)
    06) It will tell you document stored successfully.
    07) You can now find your logo under the heading OURCOMP in top left window.
    08) You can reference the logo in things like FM REUSE_ALV_COMMENTARY_WRITE or any other area which may reference these things. EG: I_LOGO = 'OURCOMP'. You can preview image by double-clicking it.
    <b>Please reward points if it helps.</b>
    Regards,
    Amit Mishra
    Message was edited by: Amit Mishra

  • Regarding Invoice and Payment slip   both needs to print sub sequently

    Hi Guys,
             i have problem with smartform ,
    the requirement was ,
    invoice and payment slip both i need to develop using smartforms,
    the thing is invoice will print on white paper(Portrait) and
    payment slip will print on pre - printed paper (landscape) ,
    subsequently it needs to print one invoice and payment slip for that invoice and
    another invoice and payment slip like this in the sequence it needs to print .
    this would be done by overnight job scheduling ,
    how could i do this ,
    what about output types and how can i proceed with technically please guide  me .
    urgent requirement ..help me out this .
    Thanks & Regards
    Vijay Kumar Reddy
    +91-9789098418
    [email protected]

    Hi Dewang,
    I have a different situation, I posted SD request at contract account level posted using FPSEC1.
    Since the contract account is for purpose of Aggregation, I did a aggregated posting then when I prepare a print doc for the same using EA10_AGGRBILL it is not picking up the security deposit request.
    I have maintained the necessary entry in Item Selection in Account Maintenance/ Define Sub-Items for RF clearing type.
    Please advice.
    Thanks
    Satyajeet

Maybe you are looking for