Desktop Real Time on Intel NUC?

I'm exploring small form factors to run RTOS, but don't have the need for FPGA (i.e. CPU only).  Just curious if anyone has tried to install LabView Desktop Real Time on any of the new Intel NUC SFF-PCs, such as the DN2820FYKH?  If so, are all the necessary devices (especially ethernet) supported?  Thanks.
-Joe

Joe,
   I'm trying to do this same thing - Building the world's smallest NI RealTime System using the Intel NUC - D54250WYKH.
   Its been an uphill battle...
   The compatibility list states the 4th generation Intel processors (in my case, an i5) in this unit is supported, but in the next month or two Intel will be releasing the the 5th generation which is currently not on the compatibility list..
   Anyone from NI care to tell us when this might happen? 
   My troubles have been around the ethernet port. The D54250WYKH has only 1 ethernet port and its the l218V chipset - This chipset is not on the currently supported list..
   Once again, Anyone from NI care to tell us when this might happen? 
   I actually need 2 ethernet ports for my application on the NUC, but have been having a terrible time finding an ethernet expansion card for the miniPXIe expansion ports that use the supported chipsets. I found 1, but it doesn't work even though it passes the "NI PC RT Evaluator" software test...   
   I'm now looking at an adaptor that converts the miniPCIe port back to the PCI format. I give this about a 50% chance of working... It's due to be delivered this Friday...
   Does any know of a PCI card that is supported by NI RealTime with 2 ethernet ports?
Barty

Similar Messages

  • Supervisor Desktop - Real time status shows the deleted agents

    Hi All,
    Recently we modified only the agent IDs for few agents.In ICM we just edited the previous entry. We have not deleted and re created it. Now the problem is the in "Supervisor Desktop - Real time status" the old entries are also reflecting in logout state. Exit_OPC will help us to remove this stale values. But is there any other metheod to to achieve this without impacting the production?
    Regards,
    Adithya

    Hi David,
    Thanks for your response. We cannot reinstall the Supervisor desktop there are multiple supervisors for this team. Will wait and check if the stale entry goes automatically. Please let me know if u come across any other process which will help in doing this.
    Regards,
    Adithya

  • Requirements for Desktop PCs as LabVIEW Real-Time Targets

    Hello
    I have read the Requirements for Desktop PCs as LabVIEW Real-Time Targets
    http://www.ni.com/white-paper/8239/en/
    and i have 2 questions:
    Supported Ethernet Chipsets:   Is Intel® i210AT Controller supported?
    Supported Processors: Is E3 and E5 Xeon Supported?
    thank you

    Dear goltnum9,
    Here some Whitepapers where you can read which Requirements must be given and also how do convert.
    Requirements for Desktop PCs as LabVIEW Real-Time Targets
    How do I Create a Desktop Real-Time System?
    Kind Regards,
    SG3 | Applications Engineering | National Instruments | NIG |

  • Read CPU temperature of Desktop PC running LabVIEW Real-Time

    Is it possilbe to read the CPU temperature of a Desktop PC running LabVIEW Real-Time? I found an older example that allows to read the temperature of PXI systems (http://www.ni.com/example/29538/en/). Is there a possibility for Desktop Real-Time Machines as well?
    Regards,
    Steffen

    Hi this is heavily dependent from your specific Hardware. Which PC or more specific which main board do you use?
    I found several examples in the NI forum that try to access the CPU data.  
    I’m using a Dell machine and both temperature VI’s are not working for me.
    Hope you have more luck.
    Attachments:
    Temperatur_der_CPU.vi ‏13 KB
    WMI_GetTemperatureProbe[1].vi ‏26 KB
    WMI_Win32procesor[1].vi ‏41 KB

  • UCCX 8 - CSD Real Time Display "N/A"

    Hello,
    We are facing an issue with Cisco Supervisor Desktop real time display "Agent Logs - call" and "Agent Logs - state". These two real time displays show "n/a" while select specific agents (some agents it show data as normal). For the agents who display "n/a" in CSD, in CAD the real time data display as normal.
    For example: When supervisor monitor Agent_A in CSD "Agent Logs - call" show "N/A" (the same to Agent Logs -state). But in CAD, Agent_A can see real time display "Agent Call Log Display" as normal (the same to "Agent ACD State Log Display").
    Does anyone experience this issue?
    It seem that the real time display data in CAD and CSD are getting from the same source. How come the CSD show "n/a" when the data is available in CAD? Any idea, please help.
    Many thanks,

    Hi Anuj,
    Thanks for your response. We are currently running on UCCX SU2. We used to reinstalled CSD/CAD already after we upgrade the UCCX to SU2. Our issue is now fixed by delete the user id of inactive agent from resource page and resync the directory  services.
    Just a note for anyone who might face similar issue, the recommendation is to first check the version of CAD/CSD running on the client PC (as Anuj suggest) and also comparing the user ID with the UCCX resource page. Be aware that user ID is case sensitive. Check the inactive agent list in the resource page. Delete the user id if you see it there. Then go to Desktop Administrator to resync the directory servcies.
    Thanks!

  • How to reset numbers in real time display in Cisco Supervisor Desktop?

    Hi all,
    I wonder about numbers in real time display in Cisco Supervisor Desktop. There are many statistic number for example : Call Handled, Max Talking, Avg Talking, Max Ready, Total Ready, Call abandoned, etc. Is there any way to reset those numbers back to zero? Please let me know.
    Thank you.

    Joe,
    I haven't tried that, but I'm very skeptical. The CAD Agent gets stats from two places - CTIOS and RASS. RASS keeps the call log information in a SQL Desktop Engine database.
    Stats derived from CTIOS reset at midnight. Obviously, restarting the RASS service has no effect on those. Call log information is being kept in a database so it seems to me that a restart of RASS should also have no effect.
    I guess I will have to try for myself.
    Regards,
    Geoff

  • How to install Vision run-time engine to a desktop PC converted to real-time target

    Hi, all
    I don't know how can I install the vision run-time engine to a desktop PC which I converted to a real-time target.  The same problem applies to installing real-time run-time engine and labview run-time engine to the real-time target.  The only way to install software to real-time target is through "add/remove software" in MAX for remote system, but it is not for all types of run-time engine installation.  
    I am also confused about how to activate those run-time engines for the desktop PC as real-time target.
    Please help and great thanks.
    Wei 

    Hi turtle,
    Here is a link that explains how to set up a desktop PC as a real-time target.  The section for Formatting & Setup should help you the most.
    NI Developer Zone Tutorial: Requirements for Desktop PCs as LabVIEW Real-Time Targets
    Justin D.
    Applications Engineer
    National Instruments

  • Desktop PC as LabVIEW Real-Time Target and DAQ ISA card

    I want to use LabVIEW Real-Time (Desktop PC + OS Pharlap ETS) for operation with DAQ ISA card.
    Pharlap ETS supports operation from Windows dll and can supports Third Party Device PCI.
    Whether there is a possibility to work with ISA card in Pharlap ETS?
    I want to work for example with card PC20TR from BMC Messsysteme GmbH.
    Does anyone have tricks for using ISA card in Pharlap ETS?

    Hi,
    If you have reviewed the requirements for a Real-Time target and verified that your computer is compliant you might want to check out this article.  The main issue that people encounter when using PC's as RT targets is have the correct network card.  Make sure the card you have is on the supported devices list on the webpage that Christian posted.  You should be able to develop a driver using low level VISA commands but it is not an easy task.  Read over the developer zone article to learn more about it.
    Eric A.
    National Instruments
    Distributed I/O Product Support Engineer

  • An agent be able to see his real time performance statistics on his desktop

    HI,
    In Cisco UCCE how can an agent be able to see his/her real time performance statistics on his desktop?
    Please suggest.
    Thanks,
    Manish

    Nope. An agent has a limited real-time view of the skill groups they belong to. They can see the number of calls in queue and how long the longest one has been waiting. They also see the number of calls they have received so far today and the average talk time.
    What do you want to see?
    Regards,
    Geoff

  • NI LabVIEW Real-Time for Desktop PCs compatibility!

    Hello,
    I'm pretending to acquire the NI LabVIEW Real-Time Deployment License for Desktop PCs. But before that, I need to be sure that this will work with other boards (not from NI).  
    Currently, I still don´t have all the project details. But there's a possibility of one board be from other supplier. 
    Can anyone tell me this, please. It's very urgent.
    Best regards,
    Paulo Carmo

    Hi Paulo,
    I guess that you will be disappointed but the response is clearly no.
    When you boot a Desktop PC as RT target, it loads with the basic real-time operating system (including drivers for ethernet, for harddrive, memory....). When you want to add drivers on this embedded system, it will be only possible to add National Instruments drivers such as DAQmx, DAQ, VISA ... The possibility to add others drivers (from others providers) is not supported.
    Hope it will help you,
    Regards
    David D. - Application Engineer - NI France

  • Is it possible to disable some popups from FEP Client on the desktop. But how to disable popups from real time protection

    Is it possible to disable some popups from FEP Client on the desktop. But how to disable popups from real time protection. This is so that end users who are non technical are not disturbed and only the I.T is aware of the viruses in teh environment.Shahid Roofi

    You could set policies which when a malware detected an action perform automatically without user interaction but there is no GPO which stop the notification, one reason could be that when notification keep appearing, then user will know something is wrong
    otherwise why FEP should display any warning.

  • Install real time 8.6 problems

    Hello all,
    I´m trying to install Real Time 8.6 on a Desktop target. I ran the verification tool and it says that it´s a compatible target.
    I created the Desktop PC utility usb drive and formatted the target with no problems.
    When I restarted the PC the network card was initialized with the following address: 169.254.81.194 and it doesn´t show up on MAX.
    It should have started with 0.0.0.0 so that we could then configure the IP Address.
    Am I doing something wrong?
    thanks,
    Adam
    Solved!
    Go to Solution.

    Hi Maxime,
    First I was installing the real time on a desktop connected with a cross over cable and when I tried to see the target on MAX it didn´t show up.That was when I posted this question here.
    This morning I started from scratch and instead of connecting directly using a cross over cable I connected the target to our LAN. The IP address was the same but I was able to change it.
    However I have some questions:
    In Labview 8.5.1 (in this same target) when I installed real time the default IP was 0.0.0.0. Has this changed?
    I tried (with Labview 8.6) to change the IP to 10.0.0.100 and connect to it using the cross over it responded to ping but did not show up in MAX. Any ideas why?
    Network interface: 10/100 Base-T Intel® 82562.
    No error apears on the screen of the target. 
    Thank you,
    Adam

  • LabVIEW2013,LabVIEW2013SP1(Real-Time付)インストールができない

    LabVIEW2013,LabVIEW2013SP1（いずれもReal-Time付）インストールの件で困っています。
    NIの技術サポートにも数度問い合わせていますが、解決していないので、 皆様のお知恵を貸して頂ければと思い、投稿します。
    経緯
    2月末にLabVIEW2013（Real-Time付）を購入し、下記パソコンにインストールを行いました。
    しかし、インストール中、度々エラーメッセージが表示されておりました。
    パソコン： HP Compaq Elite 8300 US/CT
    ＯＳ： Windows7 32bit PRO
    パソコンも最近買ったものです
    その後、LabVIEW2013SP1（Real-Time付）のDVDが届いたので、これをインストールしたところ、
    やはりエラーメッセージが表示され、インストールが完全に成功していないようでした。
    ただ、確認のため、同時に購入したPXIをMAXで認識させて、 Real-Timeのプロジェクトを作る準備ができるかなと思い、付属の手順のとおり作業しましたが、 Real-Timeのプロジェクトが作れませんでした。
    （手順書のとおりできない・・・RealTimeに関する項目が出てこない）
    また、サンプルファインダでReal-Timeのプログラムを探して開きましたが、絵のとおり!マークが表示されます。
    インストールがうまくいっていないと思い、 アンインストールとインストールを数度繰り返しています。
    最初のLabVIEW本体のインストールは成功しますが、そのあとのReal-Time以降インストールが失敗し、 あとはエラーメッセージが表示され、ほとんどインストールできません。 何度か再インストールを行っていますが、いまだ解決に至っていません。
    再インストールの際、行ったことは、
    １．HP Protect Tools一式の削除（hp制のセキュリティソフト）
    ２．Intel Management and Security Statusの終了
    ３．ファイアウォールの無効化
    です。
    なお、３のファイアウォールの無効化の際、ドメインプロファイルのファイアウォールも無効にしたところ、 再インストールの際の動作が改善し、その前よりもインストールできたソフトが多くなりました。
    また、インストール作業の最後のほうで、「ファイアウォールが有効になっています」と毎回表示されます。
    （ファイアウォールは無効にしているにも関わらず）
    質問：
    １．インストールに失敗する原因と解決策のヒントがありましたら、教えてください。
    ２．上記パソコンでのインストール成功例がありましたらお知らせください。
    参考までに絵を添付します。 エラーメッセージはいくつも出ていますが、抜粋して添付します。
    インストールの概要
    インストールされていない
    NI SignalExpress 2013
    NI Real-Time Execution Traceツールキット2013
    LabVIEW 2013 VI Analyzerツールキット
    LabVIEW 2013 Report Generation for Microsoft Officeツールキット
    LabVIEW 2013 PID and Fuzzy Logicツールキット
    LabVIEW 2013 Unit Test Frameworkツールキット
    LabWindows/CVI 2013 SP1 開発システム
    NI デバイスドライバ - 2014年2月版
    インストール済み
    LabVIEW 2013 SP1 （日本語版） (アクティブ化)
    LabVIEW 2013 SP1 Real‐Timeモジュール - 日本語版　　　　　　　←インストール済になっていますが、実際は使用できません LabVIEW 2013 Digital Filter Designツールキット (アクティブ化)
    LabVIEW 2013 Database Connectivityツールキット (アクティブ化)
    LabVIEW 2011 Advanced Signal Processingツールキット (アクティブ化)
    LabVIEW 2013 DataFinderツールキット (アクティブ化)
    LabVIEW 2013 Desktop Execution Traceツールキット (アクティブ化)
    LabVIEW 2013 System Identificationツールキット (アクティブ化)
    LabWindows/CVI SQLツールキット2.2 (アクティブ化)
    LabWindows/CVI Signal Processingツールキット7.0.2 (アクティブ化)
    LabWindows/CVI PID Controlツールキット2.1 (アクティブ化)
    LabWindows/CVI Execution Profiler 1.0 (アクティブ化)
    NI Real-Time Execution Traceツールキット2013 (アクティブ化)
    NI一般セキュリティパッチQ2 2013
    解決済！
    解決策の投稿を見る。
    添付:
    サンプル.PNG ‏73 KB
    13411.PNG ‏115 KB
    ドメインプロファイル2.png ‏229 KB

    まずReal Timeについて確認させてください。
    インストール済み
    LabVIEW 2013 SP1 （日本語版） (アクティブ化)
    LabVIEW 2013 SP1 Real‐Timeモジュール - 日本語版
    LabVIEW 2013 Digital Filter Designツールキット (アクティブ化)
    の中で、Real-Timeモジュールだけがアクティブ化となっていないことが気になります。
    一応の確認ですが、License ManagerでReal Time Moduleはどのような状態になっていますか？
    アクティブ化されていれば添付のように緑色のアイコンになっているはずなのですが
    Tepig
    Certified LabVIEW Associate Developer
    添付:
    rt.PNG ‏2 KB

  • How to install the NI-DAQmx driver on a real time target PC?

    Hi, I’m painful about how I can install a PCI-6363 DAQmx on my real time desktop PC target. The PCI-6363 is directly connected to the real time PC. And I’m using LabVIEW 2011 and MAX 5.0. 
    The DAQmx device driver can be seen in software lIst in the host PC, but it can not be found in the install wizard. Is there something wrong with my host PC? or is that wrong to connect PCI-6363 with real time desktop PC?
    I would be grateful for any advice that I could get here.
    Solved!
    Go to Solution.

    Hi Zhleo,
    If you are about to use the PCI-6363 with the Real-Time Desktop you are right you need to have it installed, and then you need to deploy DAQmx driver software to the real-time target.
    To do that you access your real-time desktop under Remote Systems in MAX and start the Real-Time Software Wizard. There you should see DAQmx listed. 
    In case you do not have DAQmx listed there, see this KB: Deploying DAQmx to a Real-Time Controller or PC?
    Regards,
    Eirikur Runarsson
    Platinum Applications Engineer
    NI Denmark

  • BT NetProtect plus – Real time scanning and update...

    I have posted this message as both a pointer in case others have the same issue as well as whether anyone has found a proper resolution.
    I have recently experianced problems with my BT NetProtect plus indicating the Real time scanning has stopped and any attempt to restart it does not work. This is accompanied with it keep promptig that there is a new update and to restart the computer. This happened every time I logged on.
    I had spent some considerable time with the BT support people who have now reinstalled the software about 6 time's after the 2 time I had already tried.
    I run Windows 7 64 bit and recently installed an SSD drive. The key thing I have subsequently discovered in my upgrade is that I changed some registry settings to make my default installation location to be my D: drive. I followed this post :
    The 64bit version has two versions of regedit. Make this change as well:
    1.) Enter into Start>Run: %systemroot%\syswow64\regedit 2.) Go to: HKEY_LOCAL_MACHINE \ SOFTWARE \ Microsoft \ Windows \ CurrentVersion 3.) Change the Path in DWORDs ProgramFilesDir, ProgramFilesDir (x86) to the new path, probably just changing the drive letter
    Everything works fine apart from BT NetProtect plus which when installed new has the above issue.  If I change the default install location back to C: drive then it installs OK and works OK when I subsequently change the default install location back to the D: drive. When I say works OK, that is until BT NetProtect plus issues a major update when the same problem appears again.
    I am waiting further contact from the 3rd line helpdesk but the 2nd line team did not seam to know of this problem.
    Has anyone else experenced it or know of a proper solution ?

    A full McAfee scan on my desktop PC can take about 2 hours or so and a full scan sometimes slows down my over 3 year old desktop PC. Thats why I only do a full McAfee scan every once in a while but I do a quick McAfee scan every 6 or 7 days.
    I do like the McAfee shredder though and use that now and again. I also got McAfee quick clean set to run at lest twice a week.  
    I have used Norton in the past and that slowed down my last PC more than McAfee from BT. The free version of AVG is good but its only an anti-virus. Some say the windows firewall is ok but not the best.
    I also have windows defender set to do a quick scan every evening around 9pm. As most nights I have my Desktop PC on at that time.
    I also do a disk clean up at leat once a day.
    Darren

Maybe you are looking for

  • Beach Ball of Death, Dark Gray Screen after Clean OS ReInstall- Please Help

    My 13" MBP is less than two months old. I read online somewhere that a company that buys large quantities of Macs has a strategy for combating the industry standard 5% hard drive failure in new notebooks. It said something along the lines of performi

  • Forwarding with utf-8 encoding

    Hi all, I've been having a problem with UTF8 encoding with jdk1.3. Here's three simple JSPs that illustrate it: MattTest3.jsp <%@ page contentType="text/html; charset=utf-8" %> <form action=MattTest5.jsp> <input type=text name=xxx> <input type=submit

  • [SOLVED] Monitor out of frequency while installing

    Past week I completed my first Arch Linux install in a laptop and everything works flawlessly, so I decided to install it also in my desktop computer. I boot from the CD, choose "Boot Arch Linux" option, some boot messages appear, some services start

  • I want to set up a collaborative work room for my company, what do I need to do so?

    I would like to set up a collaborative work room in our company using Apple, what do I need to acomplish such thing: server, ipads, ipods, iphones, smartboard, touchboard, wireless net, certificate logins, vpn, whoever can help me with a few lines fo

  • Automatic Tax in Idoc ACC_DOCUMENT03

    Hi, I'm trying to implement an interface that send ACC_DOCUMENT03 Idoc to SAP to account invoices in out ERP. Everything is all right but we are having a problema with the taxes, we couldn't do that SAP calculate the tax automatic. Is there any field